Page 1
Owner’s Manual
Single Flat Screen Flex Arm
Desk Clamp
MODEL: DDR1327SFC
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
75x75/100x100
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте компании
Tripp Lite по адресу: www.tripplite.com
Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: www.tripplite.com
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2014 Tripp Lite. All rights reserved.
27”
MAX
1
10kg
(22lbs)
MAX
14-12-061-9333E9.indd 1 12/15/2014 2:01:59 PM
Page 2
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this manual. If you have any questions regarding any
of the instructions or warnings, please visit www.tripplite.com/support.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experience and a full understanding of this manual.
• Make sure that the mounting surface can safely support the combined load of
the equipment and all attached hardware and components.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over-tighten. Over-tightening can damage the
items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
Warranty & Product Registration
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects
in material and workmanship for a period of 5 years from the date of initial purchase. If the product should
prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY
SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,
INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these devices for any specific application.
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
2
14-12-061-9333E9.indd 2 12/15/2014 2:01:59 PM
Page 3
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to
installing. If any parts are missing or faulty, visit www.tripplite.com/support for service.
Adapter Bracket Assembly (x1)
Pole (x1) Desk Clamp Assembly (x1)
Package M
M4X14 (x4)
M5X14 (x4) D5 Washer (x4)
Package P
3mm Hex Key (x1)
Base Plate (x1)
3
14-12-061-9333E9.indd 3 12/15/2014 2:01:59 PM
4mm Hex Key (x1)
Pad (x1)
Page 4
1. Remove the VESA Plate
3mm Hex Key
Adapter Bracket Assembly
• Use Hex Key to loosen the screws in order to separate the VESA plate from the Adapter Bracket Assembly.
• Retain these screws for later use.
VESA Plate
2. Install the Pole and Desk Clamp Assembly
tighten
adjustable height
3mm Hex Key
tighten
3mm Hex Key
collar
3mm Hex Key
loosen
4
14-12-061-9333E9.indd 4 12/15/2014 2:02:01 PM
Page 5
3. Desk Installation
3a. Edge Installation
Note: min. desktop thickness=10mm (.4”)
max. desktop thickness=90mm (3.5”)
tighten
• Determine approximate location for mount, keeping in mind display size, height adjustment and pitch/roll
requirements.
• Slip the desk mount assembly over the edge of desk so that clamp fully contacts desk edge.
• Turn the knob to adjust the clamp to edge of desk and secure it tightly.
Note: If more secure clamping pressure is needed for thinner desktop surfaces, adjust the clamp adjustment
plate by removing the two screws from the desk clamp assembly, then align the clamp adjustment plate with
the desk clamp assembly’s upper holes and reattach using the same screws.
5
14-12-061-9333E9.indd 5 12/15/2014 2:02:02 PM
Page 6
3. Desk Installation
3b. Hole Installation
Disassemble the desk clamp assembly by removing the clamp
adjustment screw, the two clamp adjustment plate screws and
the base plate’s three attachment screws.
Base Plate
Rubber Pad
Re-install the base plate with three retained attachment screws. Tighten securely.
From below the desk, insert retained clamp adjustment screw through pad and up through the hole in the desk.
Thread screw by turning the knob into base plate, but do not tighten completely at this time. Center the desk
mount assembly over the hole and then securely tighten the Clamp Adjustment Screw.
Attachment Screw
4mm Hex Key
Note: min. hole diameter =10mm (.4”)
max. hole diameter =70mm (2.75”)
Pad
Clamp Adjustment Screw
6
14-12-061-9333E9.indd 6 12/15/2014 2:02:02 PM
Page 7
4. Install Adapter Bracket Assembly
collar
Insert the adapter bracket assembly
onto the pole and slide it down until it
touches the collar.
tighten
adjust handle
To tighten the adapter bracket assembly, push the plastic handle in and turn upward until it can turn no more.
Then pull the plastic handle out to disengage from the hex bolt and turn it down to the bottom position. Once
again, tighten by pushing the plastic handle in and turning upward until it can turn no more. Continue process
until firmly secured.
Note: Repeat the same process to loosen, except push the plastic handle downward from the top position.
7
14-12-061-9333E9.indd 7 12/15/2014 2:02:02 PM
Page 8
5. Install VESA Plate
Lift the display and align the rear mounting holes with the mount’s VESA plate.
Top of Display
TV
TV
TV
D5 Washer
M4X14
M5X14
Attach the display to the VESA plate with the appropriate included screws.
Do not over-tighten screws.
8
14-12-061-9333E9.indd 8 12/15/2014 2:02:03 PM
Page 9
6. Install the Display
3mm
Hex Key
Using an assistant or mechanical lifting equipment, lift the display with attached VESA plate and slide onto the
head of the adapter bracket assembly. Use the screws removed in Step 1 to secure the VESA plate and display
to the adapter bracket assembly. Make sure the display is safely secured before releasing.
9
14-12-061-9333E9.indd 9 12/15/2014 2:02:03 PM
Page 10
7. Cable Management
Use clips for routing the cables.
Note: Leave slack in the cable for arm movement.
10
14-12-061-9333E9.indd 10 12/15/2014 2:02:03 PM
Page 11
8. Adjustment
It may be necessary to slightly loosen or
tighten the adjustment screw depending on
the weight of display installed.
4mm
Hex Key
180°
Adjust to the desired position or tilt.
180°
180°
360°
+15°
– 15°
3mm
Hex Key
Once the display is adjusted to its final
desired position, tighten the collar using a
3mm Hex Key.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please visit www.tripplite.com/support if you have any questions.
11
14-12-061-9333E9.indd 11 12/15/2014 2:02:04 PM
Page 12
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
12
14-12-061-9333E9.indd 12 12/15/2014 2:02:04 PM
14-12-061 • 93-33E9_RevA
Loading...