Tripp Lite B024-HU08, B024-HU16 Quick Start Guide

4 5

connector with screw lock. selection includes a speaker jack, a USB Type-B connector and an HDMI Cables that link the switch to the computers connect here. Each KVM port

the second or third level of a cascaded installation. Note: The USB 2.0 hub cannot be accessed through the switch by computers on

port. USB 2.0 peripherals (printers, scanners, etc.) can be connected to the

Connect a grounding wire to ground the switch (optional).

appropriate icon to indicate the connector type. mouse and speakers connect here. Each connector is marked with an The cables from the console HDMI monitor, USB keyboard, USB

Selection

KVM Port

Hub

USB 2.0 Terminal

Grounding

Selection

Console Port

Power Jack The power adapter cable connects here.

Key Component Description

K L

(Model B024-HU08 shown)

Rear Panel

Power LED Illuminates to indicate the switch is powered and ready to operate.

complete. After the reset is complete, you can log in again. the unit beeps and the port LEDs ﬂash in succession until the reset is

the second or third level or a cascaded installation. Note: The USB 2.0 hub cannot be accessed through the switch by computers on

port (a user-supplied power adapter may be required). USB 2.0 peripherals (printers, scanners, etc.) can be connected to the

included Firmware Upgrade Cable to this port. This port is used to upgrade the ﬁrmware on the KVM switch. Connect the

connector have priority over those plugged into the rear panel.

Firmware Upgrade Recovery). upgrade recovery (for details, see Owner’s Manual section 13.6 does not complete successfully, this switch is used to perform a ﬁrmware switch should be in the NORMAL position. If a ﬁrmware upgrade operation During normal operation and while performing a ﬁrmware upgrade, the

Reset Switch Pressing this switch performs a system reset. When the system is reset,

Hub

USB 2.0 Upgrade Port

Firmware

Audio Port Connect speakers to this port (optional). The speakers plugged into this

Switch Recovery Upgrade

Firmware

Key Component Description

FFGGH

port is the one with access to the USB peripherals.

• Lights green to indicate the computer connected to the corresponding

USB

being accessed under Auto Scan mode.

• Flashes to indicate the computer connected to the corresponding port is

corresponding port has the KVM focus (Selected).

• Illuminates bright orange to indicate the computer connected to the

• Flashes to indicate Firmware Upgrade mode is in effect.

corresponding port is up and running (On Line).

• Illuminates dim orange to indicate the computer attached to the

KVM

LEDs are on the left. The USB LEDs are on the right.

* For more details, see Owner’s Manual section 9.2 Port Selection.

Manual section 11.11.3 Mouse Emulation Control).

• For independent switching, enable mouse emulation (see Owner’s

11.6 Keyboard/Mouse Reset). keyboard and mouse reset (for details, see Owner’s Manual section

• Press pushbuttons 7 and 8 simultaneously for 2 seconds to perform a

Mode). Scan Mode (for details, see Owner’s Manual section 11.4 Auto Scan

• Press pushbuttons 1 and 2 simultaneously for 2 seconds to start Auto

audio selection to the computer attached to its corresponding port.

• Press a pushbutton for longer than two seconds to bring the KVM and

corresponding port. the KVM, USB hub, and audio focus to the computer attached to its

• Press a port selection pushbutton for less than two seconds to bring For manual port selection*:

Port LEDs The Port LEDs are built into the Port Selection Switches. The KVM Port

Pushbuttons Selection

Port

Key Component Description

Model B024-HU16

AAB

Model B024-HU08

Front Panel

Regulatory Compliance

FCC Notice, Class A

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The user must use shielded cables and connectors with this equipment. Any changes or modiﬁcations to this equipment not expressly approved by Tripp Lite could void the user’s authority to operate this equipment.

Regulatory Compliance Identiﬁcation Numbers

For the purpose of regulatory compliance certiﬁcations and identiﬁcation, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marketing name or model number of the product.

Introduction

Quick Start Guide

NetDirector® 8/16-Port 1U

Rack-Mount HDMI/USB KVM

Switch with Audio and

Peripheral Sharing

Models: B024-HU08, B024-HU16

A complete Owner’s Manual is available on Tripp Lite’s website: tripplite.com.

Tripp Lite has a policy of continuous improvement. Speciﬁcations are subject to change without notice. Photos and illustrations may differ slightly from actual products.

Este manual esta disponible en español en la página de Tripp Lite: tripplite.com

Ce manuel est disponible en français sur le site Web de Tripp Lite : tripplite.com

Русскоязычная версия настоящего руководства представлена на

веб-сайте компании Tripp Lite по адресу: tripplite.com

WARRANTY REGISTRATION

tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

8 1

20-01-046 93-3B86_RevB

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

6 3

KVM Cable Set HDMI USB

Sun Solaris 8 and higher FreeBSD 5.5 and higher AIX 4.3 and higher Ubuntu 7.04 / 7.10 Debian 3.1 / 4.0 SuSE 10 / 11.1 and higher RedHat 9.0 and higher Kernal 2.6 and higher

Novell Netware 6.0 and higher

UNIX

Linux Mac OS 9.0 and higher Windows 2000 and higher

Operating System Version

Supported Operating Systems:

• Speaker ports (Optional)

• USB Type-A port

• Source with an HDMI port

Computers

• Speakers (Optional)

• USB Mouse/Keyboard

• HDMI-compliant monitor

Console

HDMI

KVM Cable Set

HDMI USB

3 7

the diagram correspond to the steps below) and perform the following: To set up single-level installation, refer to the following installation diagram (the numbers in

Single-Level Installation

surges or static electricity

• It is recommended to properly ground the KVM switch to prevent damage to your installation from

• Make sure power to all devices that you will be connecting has been turned off

Note: Before beginning installation:

System Requirements

Product Features

• Control up to eight (B024-HU08) or 16 (B024-HU16) HDMI computers and two USB 2.0 peripheral devices using one centralized monitor, keyboard and mouse.

• Cascade up to three levels with the B024-HU08 (control up to 512 computers) or two levels with the B024-HU16 (control up to 256 computers).

• Effortlessly switch between computers using either the front panel buttons, hotkeys or on-screen display (OSD).

• The KVM and USB focus can be switched independently of one another; for example, you can access one computer while simultaneously printing from another computer.

• Support HDMI video resolutions up to 1920 x 1200 @ 60 Hz.

• Console mouse emulation supports multi-functional mice and most mouse drivers.

• OSD Backup/Restore feature allows the administrator to back up the switch’s conﬁgurations and user proﬁle information.

Package Includes

Installation

Plug a USB keyboard and a USB mouse in the USB console ports located on the unit’s

rear panel.

Connect an HDMI monitor into the HDMI console port and power it on.

Plug primary speakers into the speaker jack located on the unit’s front panel. These

speakers have priority over those plugged into the rear panel.

Plug secondary speakers into the audio port located on the unit’s rear panel (optional).

Using Tripp Lite’s P782-0XX-HA HDMI/USB/Audio KVM cable kit or individual HDMI, USB

and audio cables, plug the HDMI connector into any available HDMI port, then plug in the accompanying USB and audio cables to their corresponding ports.

At the other end of the cable, plug the USB, video and speaker cables into their

respective ports on the computer.

Plug USB peripherals into the Type-A connectors in the USB hub section.

Plug the power adapter that came with the switch into an AC power source, then plug the

power adapter cable into the switch’s power jack.

Power on connected computers.

Installation

• B024-HU08 or B024-HU16

• HDMI/USB Custom KVM Cable Kits (x2) – 6 ft.*

• Firmware Upgrade Cable – 6 ft.

• External Power Supply with C13 to NEMA 5-15P Power Cord (Input: 100-240V, 50/60 Hz,

0.7A; Output: 5V 4A)

• Rubber Feet (x4)

• Mounting Hardware

• Quick Start Guide

* Note: The microphone connector on the cable kit will not be used because the B024-HUXX supports speakers only.

Optional Accessories

• P569-Series High Speed HDMI Cables

• UR022-Series USB 2.0 Reversible A/B Cables

• P312-Series 3.5mm Mini Stereo Audio Cables

• P782-0XX-HA HDMI/USB/Audio Custom KVM Cable Kits*

* P130-000 HDMI to DVI adapter sold separately.

Warranty & Product Registration

2-Year Limited Warranty

TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of two (2) years from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment which has been damaged by accident, negligence or misapplication or has been altered or modiﬁed in any way. EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s)may not apply to the purchaser. EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Speciﬁcally, TRIPP LITE is not liable for any costs, such as lost proﬁts or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

Product Registration

Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

2 7