Tripp Lite 232, 216 User Manual

Page 1
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright ©2012 Tripp Lite. All rights reserved.
Smart 216 / 232 – Quick Start Guide
1. Introduction
To take advantage of the Smart 216 / 232 full range of features, we recommend you read the softcopy User Guide after performing the Quick Start procedure. It’s in PDF format on the supplied CD or on our website www.minicom.com in the Support section.
All references throughout this guide to the Smart 216 refer equally to the Smart
232. The two units are functionally the same. The Smart 216 has 16 Server ports and the Smart 232 has 32 Server ports.
The Smart 216 extends your KVM (keyboard, video, and mouse) from servers with PS/2 or USB interfaces up to 30m/100ft away. 2 users can control, monitor and manage up to 16 servers simultaneously. You can connect a Power Distribution Unit (PDU) for power management.
2. System components
The system consists of:
1 Smart 216 (p/n 1SU22090) or 1 Smart 232 (p/n 1SU22091)Rack mounting set (p/n 5AC20247)ROCs - PS/2, USB
3. The Smart 216 unit
Figure 1 illustrates the front panel of the Smart 216.
MINICOM
Power RemoteLink
21
Figure 1 Smart 216 ports – side 1
SMART 216 A
Page 2
3.1 LED and button table
LED Function
Power Link Remote 1 and 2
Power Indicator Unit is connected to the network Illuminates when the respective user connects to a server
SMART 216 / 232
I 0
POWER
100-240 VAC 50/60 Hz
Power
Remote Power Switch (RPS) port
RPS
LAN
LAN (Ethernet) port
Monitor
USER 2
Keyboard
Mouse
Monitor
USER 1
Keyboard
1 2 3 4 5 6 7 8
Mouse
SERVER
Server ports
10 11 12 13 14 15 169
Figure 2 Smart 216 ports – side 2
3.2 Connector table
Connector Function
User 1 and User 2 KVM consoles
RPS LAN
Server ports
Connect 2 KVM consoles for two users to operate the Smart 216
Connect Minicom’s Serial Remote Power Switch To configure and update the unit, connect to 10/100 Mbit
Ethernet. Connect to servers via ROCs
4. Pre-installation guidelines
Place cables away from fluorescent lights, air conditioners, and machines that
are likely to generate electrical noise
Place the Smart 216 on a flat, clean and dry surface or install in a rack Ensure that the maximum distance between each computer and the Smart 216,
does not exceed 30m/100ft.
5. Connecting the system
Figure 3 illustrates the Smart 216 system overview.
1
Page 3
QUICK START GUIDE
User 2
Keyboard, monitorand mouse connectedto KVM User2 ports
POWER
100-240 VAC 50/60 Hz
PDU connectedto RPS port
User 1
Keyboard, monitorand mouse connectedto KVM User1 ports
I
0
RPS
USER 1
USER 2
LAN
1 2 3 4 5 6 7 8
SERVER
10 11 12 13 14 15 169
To servers
ROCs
PDU
Figure 3 Smart 216 system overview
5.1 The ROCs
Each computer/ server is directly connected to the Smart 216 via theappropriate RoC using CAT5 cable in a star configuration. No external power is needed at the ROCs. The ROCs draw their power from the computer’s keyboard port (ROC PS/2) or from the USB port (ROC USB). The figures below illustrate the ROC PS/2 and ROC USB.
2
Page 4
SMART 216 / 232
Figure 4 ROC PS/2
To computer’s Video Card
To computer’s USB Port
Figure 5 ROC USB
5.1.1 Connecting a ROC PS/2
To computer’s keyboard port
To computer’s mouse port
To computer’s Video card
1. Switch off the server.
2. Connect the ROC PS/2. Figure 6 illustrates the ROC PS/2 connections.
3. Power on the server. You can connect the ROC PS/2to a powered on computer, but it must be in the
following order:
1. Connect the Mouse connector to the computer’s Mouse port.
2. Connect the Keyboard connector to the computer’s Keyboard port.
3. Connect the Screen connector to the computer’s Video port. Failure to connect in the above order while the server is running, may lead to the
mouse malfunctioning until the server is rebooted.
3
Page 5
QUICK START GUIDE
To Keyboard port
Keybd
Mouse
100T
Parallel
VideoSerialA
SerialB
PCI 33Mx32b PCI 33Mx32b PCI 33Mx32b PCI 33Mx32b
SCSI
CAT5 cable to switch Server port
To Mouse port
ROC PS/2
To Video port
Figure 6 ROC PS/2 connections
5.1.2 Connecting a ROC USB
The ROCUSB supports Windows 98 SE and later, MAC, SUN and SGI, and all modern Linux distributions. Figure 7 illustrates the ROC USB and its connections.
To connect the ROC USB:
1. Connect the Screen connector to the computer’s Video port.
2. Connect the USB connector to the computer’s USB port.
To Video port
ROC USB
CAT5 cable toswitch Server port
Figure 7 ROC USB
5.2 Connecting the CAT5 cables
1. Connect one connector to the ROCs RJ45 port.
2. Connect the other connector to one of the Smart 216’s Server ports.
3. Follow the above 2 steps for each computer.
4
To USB port
Page 6
SMART 216 / 232
5.3 Connecting the two KVM consoles
Connect a keyboard,monitorand mouseto each of the User 1 and User 2 ports as follows:
1. Connect the monitor connectors to the Monitor ports.
2. Connect the USB keyboard connectors to the USB Keyboard ports.
3. Connect the USB mouse connectors to the USB Mouse ports.
5.4 Connecting to the power supply
1. Using the Power cord provided, connect the Smart 216 to a socket outlet with grounding connection. Only use the power cord supplied with the unit.
2. Switch on the Smart 216.
6. Connecting to the Local Area Network (LAN)
Configuration is done mainly via a web interface. For this purpose connect a network cable to the LAN port of the Smart 216. This must be done before powering on the Smart 216.
7. Setting network parameters via the OSD
By default, Smart 216 boots with an automatically assigned IP address from a DHCP (Dynamic Host Configuration Protocol) server on the network. The DHCP server provides a valid IP address, gateway address and subnet mask.
You can identify the IP address from the OSD. Also where there is no DHCP server set the IP address via the OSD as follows:
1. From the local keyboard, press left Shift twice. The OSD Main window appears.
2. Press F2. The Settings window appears see Figure 8.
Figure 8 Settings window
5
Page 7
QUICK START GUIDE
In the Settings window you navigate downwards using the Tab key. At the bottom of the window, press tab to go to the top of the window. Change settings by typing in the selected area or by pressing the spacebar – whichever is relevant.
8. Logging into the web configuration
1. Open your web browser.
2. Type the Smart 216 system IP address – http or https://IP address/ - and press Enter. The login page appears.
3. Type the default Administrator user name - admin - and password - access - (both lower case).
4. Press Enter. The web interface opens at the Targets page. See Figure 9.
Figure 9 Targets page
Columns: Server name - The server name can be changed in the configuration settings to
give the server an identifiable name. Server Status - Server Status can be on, off or busy (i.e. a user is accessing the
server). User – The current user (if any) accessing the server. From the Targets page menu - see Figure 9 - an Administrator can:
Change the passwordReach the configuration pagesSee an event log
6
Page 8
SMART 216 / 232
9. Operating the system via the OSD
To display the OSD:
1. From the local keyboard, press the left Shift key twice. The OSD Main window appears. See Figure 10.
Server status: Port number appears here
Instruction keys
Figure 10 OSD Main window
9.1 Navigating the OSD Main window
To navigate up and down use the Up and Down arrow keys.
Off
Server status: On
To exit the OSD press Esc.
9.2 Selecting a computer
To select a computer:
1. Navigate to the desired computer line. Or, type the two-digit port number of the desired computer.
2. Press Enter. The selected computer is accessed. A Confirmation label appears showing which computer is accessed.
For the full configuration and operation instructions see the full softcopy User
Guide on our website:
http://www.minicom.com/supportuserguides.htm
7
201204201 •933196_EN
Loading...