TRENDnet Wireless 802.11g AP, TEW-410APB User Manual
TEW-410APB
Wireless 802.11g AP
User’s Manual
User’s Guide
Version 1.4
0
Copyright Statement
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical,
photocopying, recording, or otherwise without the prior writing of the publisher.
July. 2003
User’s Guide
1
Contents
1. Introduction.............................................................................................................. 3
2. Safety Notification ................................................................................................... 4
3. Hardware Installation .............................................................................................. 5
4 Web Management Settings ...................................................................................... 6
4.1. Primary Setup ………………………………………………………………………………………………7
4.2. System…..………………………………………………………………………………………………….11
4.3. Operating Mode……………………………………………………………………………………………12
4.4. Status……………………………………………………………………………………………………….14
4.5 Traffic Log…………………………………………………………………………………………………..15
4.6 AccessControl ……………………………………………………………………………………………..16
4.7 Advanced Wireless………………………………………………………………………………………..17
4.8. SNMP………………………………………………………………………………………………………19
4.9. Upgrade Firmware………………………………………………………………………………………..20
5. Troubleshooting .................................................................................................... 22
User’s Guide
2
1. Introduction
Thank you for purchasing your AP Wireless 802.11g AP.
This user guide will assist you with the installation procedure.
The package you have received should contain the following items:
AP Wireless 802.11g AP
User Guide
Power Supply / Cord
Ethernet Cable
Note: if anything is missing, please contact your vendor
User’s Guide
3
2. Safety Notification
Your Wireless AP should be placed in a safe and secure location. To ensure proper operation, please
keep the unit away from water and other damaging elements. Please read the user manual thoroughly
before you install the device. The device should only be repaired by authorized and qualified
personnel.
Please do not try to open or repair the device yourself.
Do not place the device in a damp or humid location, i.e. a bathroom.
The device should be placed in a sheltered and non-slip location within a temperature range of
+5 to +40 Celsius degree.
Please do not expose the device to direct sunlight or other heat sources. The housing and
electronic components may be damaged by direct sunlight or heat sources.
User’s Guide
4
1. Power on 2. Reset to default 3. Firmware upgrade (first 1
h wireless
Used to connect to the power outlet. Only use the power
of an unauthorized
power adapter may cause damage to your device and
Press the Reset Button for approximately ten seconds, all
your PC, hub,
3. Hardware Installation
Front Panel
The front panel provides LED’s for device status. Refer to the following table for the meaning of each
feature.
LED STATUS Description
PWR/STAT
Off No power
Link
Green On
Green
Blink
Off no Ethernet link detected
minute)
1. System up 2. Power on 3. Firmware upgrade
Green On 10/100Mbps Fast Ethernet link detected. No activity.
Active
Green
Blink
Green
Blink
Indicates data traffic on the 10/100 Mbps LAN
Indicates the device is linking or active data throug
links
Rear Panel
The rear panel features 1 LAN ports and Reset button. Refer to the following table for the meaning of
each feature.
Power (DC 5v)
adapter provided with the device. Use
violate your warranty.
Reset
LAN
configurations will set to factory default settings.
The RJ-45 Ethernet ports used to connect
switch or Ethernet network.
AP Default Settings
The default settings are shown following.
User admin
Password admin
AP IP Address 192.168.1.250
AP Subnet Mask 255.255.255.0
RF ESSID ap11g
11g RF Channel 6
Mode 11b+g
Encryption Disabled
User’s Guide
5
Quick power cycle can caused system corruption. When power on, be careful not to shut down in
4
Web Management Settings
TURN ON POWER SUPPLY
about 5 seconds, because data is writing to the flash.
START UP & LOGIN
In order to configure the Wireless 11g AP, you must use your web browser and manually input
http://192.168.1.250 into the Address box and press Enter. The Main Page will appear.
To start configure the Wireless 11g AP, you must login as “admin” in the User Name box. And input
password “admin” on the password section.
Once you have logged-in as administrator, it is a good idea to change the administrator password to
ensure a secure protection to the Wireless 11g AP. The Security Settings section described later in
this manual describes how to change the password.
Once you have input the correct password and logged-in, the screen will change to the Setup page
screen.
User’s Guide
6
connect the
4.1. Primary Setup
MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER
To change the configuration, use Internet Explorer (IE) or Netscape Communicator to
WEB management 192.168.1.250.
Primary Setup
This screen contains all of the AP's basic setup functions.
.
Most users will be able to configure the AP and get it working properly using the settings on this
screen.
LAN IP Address and Subnet Mask:
This is the AP's IP Address and Subnet Mask as seen on the
internal LAN. The default value is 192.168.1.250 for IP Address and 255.255.255.0 for Subnet Mask.
User’s Guide
7
Loading...