Page 1
2
FCC Warning
This equipment has been tested and found to comply with the
regulations for a Cl as s B digi ta l devi c e , purs ua nt t o Pa rt 15 o f
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if it’s not installed and used in accordance with
this user’s guide, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own
expense.
CE Mark Warning
This is a Class B product. In a domestic environment, this
product may cause radio interference, i n which case the user
may be required to take adequate measures.
VCCI Class B Compliance (Japan)
This is a product of VCCI Class B Compliance
P/N: 1907SHUN2105001
Page 2
3
Table of Contents
INTRODUCTION............................................4
ABOUT THE USB 2.0 TO 10/100MBPS FAST
ETHERNET ADAPTER...................................... 4
PRODUCT FEATURES ...................................... 4
INSTALLATION ............................................. 5
ASPECT DESCRIPTION ....................................5
HARDWARE & SOFTWARE INSTALLATION.......5
LED INDICATORS........................................... 6
USB CONNECTOR PIN ASSIGNMENT.............. 7
SPECIFICATIONS.......................................... 8
4
INTRODUCTION
Thanks for purchasing of the USB 2.0 to
10/100Mbps Fast Ethernet Adapter. This Adapter
will allow your computer to connect to 10Mbps
Ethernet or 100Mbps Fast Ethernet Network
through USB 2.0 interface.
About the USB 2.0 to 10/100Mbps Fast
Ethernet Adapter
The USB 2.0 to 10/100Mbps Fast Ethernet
Adapter allows user to connect up to 10Mbps
Ethernet or 100Mbps Fast Ethernet Network
through their USB 2.0 ready PC.
The USB 2.0 to 10/100Mbps Fast Ethernet
Adapter is designed to provide quicker and easier
access to a type ‘A’ plug for connecting to USB
2.0 Hub or the PC’s USB 2.0 port, the RJ-45
Ethernet Port for connecting to 10Mbps Ethernet
or 100Mbps Fast Ethernet Network.
Product Features
Compliant with USB specification 1.0, 1.1
and 2.0
IEEE 802.3 10BASE-T Ethernet, IEEE
802.3u 100BASE-TX specification
ANSI/IEEE 802.3 Auto-negot iation
Plug-and-Play
Supports Bus-power mode. No external
power needed.
Page 3
5
One dual color LED indicator for Ethernet
port status.
INSTALLATION
The USB 2.0 to 10/100Mbps Fast Ethernet
Adapter is designed to be simple and easy
install.
Aspect Description
Hardware & Software Installation
Step-1: Make sure the PC is power on and
running at Windows Operating System
Step-2: Connect to Adapter to a 10Mbps,
100Mbps or 10/100Mbps Hub/Switch through
RJ-45 Ethernet Port.
Step-3: Insert USB A-type plug of the Adapter to
PC’s USB port.
6
Step-4: The Windows system will show a “New
Hardware Found” window. Click “Next”
Step-5: Put the USB 2.0 to Ethernet Adapter
driver program CD into CD-ROM Driver and
select “Search for the best driver for your device
(Recommended)”. Click “Next”
Step-6: The system will ask you to indicate the
best driver. Make sure the CD driver is selected
and drive d:\ is specified. Click “Next” to
continue.
Step-7: The system will search the specified
driver and start to download the pointed driver.
Click “Next” to Continue.
Step-8: When the system finish the driver
installation, click “Finish” button.
Step-9: Then the system will ask you to restart
your computer. Click “Yes” to restart compu ter..
LED Indicators
The USB 2.0 to 10/100Mbps Fast Ethernet
Adapter is equipped with LED indicator:
LAN Port status LED:
This indicator green when the port is connected
to 100Mbps Fast Ethernet Hub, if the Adapter to
which the hub is connected is powered off, or if
Page 4
7
there is a problem with the link, the LED will
remain off. When the indicator blinking green
while the data will be received to the 100Mbps
Fast Ethernet port. Otherwise, This indicator
indicates amber when the port is c onnected to
10Mbps Ethernet Hub, if the Adapter to which
the hub is connected is powered off, or if there is
a problem with the link, the LED will remain off.
When this indicator blinking amber while the
data will be received to the 10Mbps Ethernet
port.
USB Connector Pin Assignment
Receptacle A Series-A Plug
Receptacle B Serie s-B Plug
8
SPECIFICATIONS
Standards: USB Specification V.1.0, 1.1, 2.0
IEEE 802.3 Ethernet Specification
IEEE 802.3u Fast Ethernet Specification
ANSI/IEEE Std 802.3 auto-negotiation
Data Speed: USB 1.0, 1.1, 2.0: 1.5, 12, 480Mbps,
Fast Ethernet: 10/100Mbps
LED indicators: Green: 100Mbps Fast Ethernet Link/Rx
Amber: 10Mbps Ethernet Link/Rx
USB Port: Series-A Plug x 1
Fast Ethernet Port: RJ-45 10/100BAS E-T port x 1
EMI Compatibility: FCC Class B, CE Class B, VCCI-II
Dimensions: 65 x 48 x 28 mm
Storage
Temperature:
Storage: -25°C ~ 70°C
Operation: 0°C ~ 40°C
Humidity:
(non-condensing)
Storage: 10% ~ 90%
Operation: 10% ~70%
Power Consumption: 1. 2 W a t t s (maximum)
Driver Support: Windows 98/2000/Me/XP
Page 5
Limited Warranty
TRENDware warrants its products against
defects in material and workmanship, under
normal use and service, for the following
lengths of time from the date of purchase.
TU2-ET100 – 5 Years Warr a nty
If a product does not operate as warranted
above during the applicable warranty period,
TRENDware shall, at its option and expense,
repair the defective product or part, deliver
to customer an equivalent product or part to
replace the defective item, or refund to
customer the purchase price paid for the
defective product. All products that are
replaced will become the property of
TRENDware. Replacement products may
be new or reconditioned.
TRENDware shall not be responsible for any
software, firmware, information, or memory
data of customer contained in, stored on, or
integrated with any products returned to
TRENDware pursuant to any warranty.
There are no user serviceable parts inside
the product. Do not remove or attempt to
service the product by any unauthorized
service center. This warranty is voided if (i)
the product has been modified or repaired
by any unauthorized service center, (ii) the
product was subject to accident, abuse, or
improper use (iii) the product was subjec t to
conditions more severe than those specified
in the manual.
Warranty service may be obtained by
contacting TRENDware office within the
applicable warranty period for a Return
Material Authorization (RMA) number,
accompanied by a copy of the dated proof of
the purchase. Products returned to
TRENDware must be pre-authorized by
TRENDware with RMA number marked on
the outside of the package, and sent prepaid,
insured and packaged appropriately for safe
shipment.
Page 6
WARRANTIES EXCLUSIVE: IF THE TRENDWARE
PRODUCT DOES NOT OPERATE AS WARRANTED
ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL
BE, AT TRENDWARE’S OPTION, REPAIR OR
REPLACEMENT. THE FOREGOING WARRANTIES
AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, EITHER IN FACT OR BY OPERATION OF
LAW, STAT UTORY OR OTHERWISE, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. TRENDWARE
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER
PERSON TO ASSUME FOR IT ANY OTHER LIABILITY
IN CONNECTION WITH THE SALE, INSTALLATION
MAINTENANCE OR USE OF TRENDWARE’S
PRODUCTS.
TRENDWARE SHALL NOT BE LIABLE UNDER THIS
WARRANTY IF ITS TESTING AND EXAMINATION
DISCLOSE THA T T HE ALLEGED DEFECT IN THE
PRODUCT DOES NOT EXIST OR WAS CAUSED BY
CUSTOMER’S OR ANY THIRD PERSON’S MISUSE,
NEGLECT, IMPROPER INSTALLATION OR TESTING,
UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY,
OR ANY OTHER CAUSE BEYOND THE RANGE OF
THE INTENDED USE, OR BY ACCIDENT, FIRE,
LIGHTNING, OR OTHER HAZARD.
LIMIT ATION OF LIABILITY: TO THE FULL EXTENT
ALLOWED BY LAW TRENDWARE ALSO EXCLUDES
FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY,
WHETHER BASED IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE), FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR
PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS
OF REVENUE OR PROFITS, LOSS OF BUSINESS,
LOSS OF INFORMATION OR DATE, OR OTHER
FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE, USE, PERFORMANCE, FAILURE,
OR INTERRUPTION OF THE POSSIBILITY OF SUCH
DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR,
REPLACEMENT, OR REFUND OF THE PURCHASE
PRICE PAID, AT TRENDWARE’S OPTION. THIS
DISCLAIMER OF LIABILITY FOR DAMAGES WILL
NOT BE AFFECTED IF ANY REMEDY PROVIDED
HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be
governed by the laws of the state of California.
Page 7
T echnical Support
You can find the most recent
driver/firmware/software and user
documentations on the TRENDware
website. TRENDware provides FREE
technical support for all customers for
the duration of the warranty period on this
product.
TRENDware Technical Support
Tel: +1-310-626-6252
Fax: +1-310-626-6267
E-mail: support@trendware.com
www.TRENDnet.com
Monday ~ Friday, 7:30AM ~ 6:00PM
Pacific Standard Time
(Except holidays)
Loading...