
Anleitung zur Schnellinstallation
TU2-ET100
V3

 1. Bevor Sie anfangen
Systemanforderungen
!
CD-ROM-Laufwerk
!
USB-Port: 2.0 order 1.1
Packungsinhalt
!
TU2-ET100
!
Treiber CD-ROM 
!
Mehrsprachige Installationsanleitung
Unterstützte 
Betriebssysteme
Windows 7 (32/64-bit) 
Windows Vista (32/64-bit)
Windows XP (32/64-bit)/ 
2000 / ME / 98SE
Mac OS X (10.6) 
Mac OS X (10.5) 
Mac OS X (10.4)
Mac OS X (10.1-10.3)
Prozessor
1GHz oder schneller 
800MHz oder schneller
300MHz oder schneller 
Intel Processor
867MHz oder schneller 
333MHz oder schneller
300MHz oder schneller
1
Speicher
1GB RAM oder mehr 
512MB RAM oder mehr
256MB RAM oder mehr 
1GB RAM oder mehr
512MB RAM oder mehr 
256MB RAM oder mehr
256MB RAM oder mehr

 2. Installation 
Note: 
1. Informationen zur Installation der Treiber für Windows 98SE und ME und 
Mac OS X finden Sie in der Bedienungsanleitung auf der Treiber-CD.
2. Installieren Sie den USB-Adapter TU2-ET100 erst dann im Computer, wenn Sie 
dazu aufgefordert werden.
Windows 7 / Vista / XP / 2000
1. Legen Sie die Treiber-CD in Ihr
CD-ROM-Laufwerk ein.
2. Klicken Sie auf Run Autorun.exe 
(Autorun.exe ausführen) (nur Windows 7/Vista).
3. Klicken Sie Install Driver .
4. Folgen Sie den Anweisungen des 
 Installationsassistenten und klicken Sie dann 
auf Finish (Fertigstellen).
2

5. Klicken Sie Exit.
6. Nehmen Sie die Treiber-CD-ROM aus dem 
CD-ROM-Laufwerk Ihres Computers.
7. Verbinden Sie den Adapter mit einem freien 
USB-Port Ihres Computers.
8. Die Treiber werden automatisch installiert.
9. Verbinden Sie den Adapter über ein 
RJ-45-Kabel mit einem Umschalter, Router 
oder Kabel/DSL-Modem.
Ihre Installation ist beendet!
3

 Troubleshooting
1. 
I inserted the Driver CD-ROM into my computer's CD-ROM Drive and the 
installation menu does not appear automatically. What should I do?
1. 
For Windows 7, if the installation menu does not appear automatically, click on  
the Windows Icon on the bottom left hand corner of the screen, click the 
“Search programs and files” box, and type D:\autorun.exe, where “D” in 
“D:\autorun.exe” is the letter assigned to your CD-ROM Drive, and then press 
the ENTER key on your keyboard
2. For Windows Vista, if the installation menu does not appear automatically, click 
Start, click the Start Search box, and type D:\autorun.exe where "D" in 
"D:\autorun.exe" is the letter assigned to your CD-ROM Drive, and then press 
the ENTER key on your keyboard.
3. For Windows 2000/XP, if the installation menu does not appear automatically, 
click Start, click Run, and type D:\autorun.exe where "D" in "D:\autorun.exe" is 
the letter assigned to your CD-ROM Drive, and then press the ENTER key on 
your keyboard.
2. Can I connect or disconnect the TU2-ET100 while the computer is on?
Yes, you can connect or disconnect TU2-ET100 while the computer is on 
because the USB interface is Plug-and-Play compliant and hot-pluggable.
3. Windows is unable to recognize my hardware.  What should I do?
1. Make sure your computer meets the minimum requirements as specified in 
Section 1 of this Quick Installation Guide.
2. Try plugging the adapter into a different USB port.
4. Windows recognizes my new hardware, but I'm unable to connect to my 
network. What should I do?
1. Verify that the RJ-45 Ethernet cable is securely connected from your switch or 
router to your adapter.
2. Verify that the LEDs on your adapter are lit.
3. Verify that the TCP/IP settings are set to Obtain an IP address automatically.
5. How do I install this device on Windows 98SE, ME and Mac OS X? 
Refer to the User Guide included on the Driver CD-ROM for installation 
instructions.
If you still encounter problems or have any questions regarding the TU2-ET100, please 
contact TRENDnet's Technical Support Department.
4

Copyright ©2010. All Rights Reserved. TRENDnet.