Trendnet TK-400, TK-200 User Manual
INSTALLATIONINSTALLATION
1. Before installation, please make sure all
peripherals and computers are powered off.
1
1
M
M
1
1
K
PC1PC1
K
V
V
G
G
A
A
2. Connect one keyboard, monitor and mouse
to KVM switch’s console port.
3. a. For TK-200: Connect PCs to K1,M1,VGA and
K2,M2, VGA of KVM switch using standard
extension Cable.
PC2PC2
Model No: TK-200
2
2
K
K
V
V
G
G
A
2
2
M
M
A
MOUSE 2
K/B 2
MOUSE K/B POWER
K/B 1
MOUSE 1
PC1
PC2
VGA 1
VGA 2MOUSE 4
MOUSE 3
K/B 4
PC3
PC4
K/B 3
VGA 4
VGA
VGA 3
Model No: TK-400
INTRODUCTIONINTRODUCTION
In situations where multiple PC Servers are installed,
user can use KVM Switches to control multiple PCs
with one Keyboard, one Monitor, and one Mouse. By
using the KVM Switch, user saves on hardware cost,
saves valuable space, and reduce energy
consumption cost. These advantages make the KVM
Switch a must-have device in multiple Servers
Environment.
1
1
M
M
V
V
G
G
A
A
1
1
K
K
PC1PC1
PC2PC2
2
2
K
K
V
V
G
G
A
A
2
2
M
M
b. For TK-400: Connect PCs to Computer 1,
Computer2, Computer 3,Computer 4 of KVM
switch using standard PC extension cable.
4. Power on all PCs. Do not press the push button on
the KVM switch and do not use “Hot key” when PCs
are booting up.
OPERATIONOPERATION
Power on
1. Power on: The KVM switch draw the power from PCs
keyboard power. One LED will lit red, meaning
the console is controlling/monitoring to the PC
that is connected to that specific port.
Push button
2. Push button: Press and then release the Port
Selection Button once changes the selected port
to the next port.
Hot key
3. Hot key: Press and then release the SCROLL LOCK
Key twice within 2 seconds, you will hear a beep
confirming entering the “Hot Key” mode.
LED will
SCROLL LOCK
FEATURESFEATURES
2/4 port KVM switch is compact size designed
for easy transport.
Support Microsoft Intellimouse, Logitech Net
Mouse...etc.
Support DOS, Win3.X, Win95/98/ME/2000
WinNT, Netware, Unix, and Linux.
Hot Pluggable; add PCs or remove connected PCs
without powering down the KVM switch or other
online PCs.
Support Video Quality Up to 1920X1440,
Band width: 200MHz.
No software Required; user can select PC via
Push button or Hot-keys.
Auto Scan mode for monitoring PCs (4 sec. interval)
Keyboard status restored when switching between PCs.
LED display for easy status monitoring.
Buzzer sound confirming port switching action.
Below are the “Hot Key” commands:
Scroll
Scroll
Lock
Lock
Scroll
Scroll
Lock
Lock
Scroll
Scroll
Lock
Lock
Scroll
Scroll
Lock
Lock
Scroll
Scroll
Lock
Lock
Scroll
Scroll
Lock
Lock
Previous Channel
Next Channel
Auto Scan
SS
In Hot key Mode, use "Up-Arrow" to Selected the
previous port, "Down Arrow" to select the next
port and Press "S" key to set the KVM switch into
Auto Scan Mode.
Note: If no command is entered in two seconds after
entering the Hot Key Mode, the switch will cancel
the Hot Key operation.
SPECIFICATIONSPECIFICATION
SYSTEM REQUIREMENTSSYSTEM REQUIREMENTS
SYSTEM REQUIREMENTSSYSTEM REQUIREMENTS
Model no.Model no.
TK-200TK-200
TK-400TK-400
TROUBLESHOOTINGTROUBLESHOOTING
Note:
Note:
Please ensure all cables are correctly seated in the connection ports. Properly
Please ensure all cables are correctly seated in the connection ports. Properly
label the cables to avoid confusion.
label the cables to avoid confusion.
Console SideConsole Side Computer SideComputer Side
One VGA Monitor
One VGA Monitor
One PS/2 keyboard
One PS/2 keyboard
One PS/2 Mouse
One PS/2 Mouse
One VGA Monitor
One VGA Monitor
One PS/2 keyboard
One PS/2 keyboard
One PS/2 Mouse
One PS/2 Mouse
Two HDB 15pin male to maleVGA cables.
Two HDB 15pin male to maleVGA cables.
Two PS/2 cables male to male for Keyboard.
Two PS/2 cables male to male for Keyboard.
Two PS/2 cables male to Male for Mouse.
Two PS/2 cables male to Male for Mouse.
Four HDB 15 pin male to male VGA cables.
Four HDB 15 pin male to male VGA cables.
Four PS/2 cables male to male for Keyboard.
Four PS/2 cables male to male for Keyboard.
Four PS/2 cables male to male for Mouse.
Four PS/2 cables male to male for Mouse.
1.TK-200/TK-400 KVM switch draws power from computer’s keyboard port. Portable computers,
such as, Laptop computers and Notebook computers, may not supply enough power to the
KVM switch to make it function properly. In this case, please connect a DC 5V~9V, 500mA~1A
AC Adapter to the power jack to compensate the lack of power. The power jack’s polarity is
center positive.
2.Don't press any keys on the keyboard while the selected computers is booting up.
This might cause “keyboard error” or “keyboard is not detected” error on the PC.
3.If the computer boots up fine, but keyboard doesn't work, please do the following:
a . Make sure the keyboard works when directly plugged into the computer.
b. Try a different keyboard, but use only 101,102 or 104-key keyboard.
4.If the Mouse is not detected after PC boots up, please do the following:
a. Make sure the mouse works when directly connected to the computer.
b. Make sure the mouse is a PS/2 mouse. A combo mouse will work, as long as it is
set to PS/2 mode.
c. Try a different mouse.
5.Avoiding moving the mouse or pressing the mouse button when switching from port to port.
PACKAGE CONTENTSPACKAGE CONTENTS
TK-200 2-port KVM switch * 1 + User's Guide * 1 + KVM cables * 2.
TK-400 4-port KVM switch * 1 + User's Guide * 1.
-MAY-09-2001-
Loading...