TRENDnet TFM-PCIV92A - 56 Kbps Fax, TFM-PCIV92A User Manual
TABLE OF CONTENT
1. Contents of Package 1
2. Comprehensive Modem Installation Instructions
1
2.1 Modem Installation
1
2.2 Hardware Installation
1
2.3 System Setup
3
2.3.1 Setup Instructions for Windows 98
3
2.3.2 Uninstall Modem from Windows 98
4
2.3.3 Setup Instructions for Windows Me
5
2.3.4 Uninstall Modem from Windows Me
6
2.3.5 Setup Instructions for Windows 2000
7
2.3.6 Uninstall Modem from Windows 2000
9
2.3.7 Setup Instructions for Windows XP
10
2.3.8 Uninstall Modem from Windows XP
12
2.4 Testing your modem
13
2.5 Install Communication Software
13
3. Troubleshooting
14
Appendix 1: Modem Specifications..…..............….......16
Appendix 2: AT Command Set ………...............……. ... 17
Appendix 3: S-Register Summary ……..............….......22
Appendix 4: Result Codes Summary..…..............….....25
Appendix 5: Government Compliance...............……....27
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
- 1 - Rev.1.00.2.1.34
Section 1 Conte nts of Package
z One V.92/V.90 PCI bus window modem
z One telephone cable
z One CD-ROM disk comprises Communication software, Modem Driver & User's Manual
z Quick installation guide
Please contact the place of purchase if any of the above listed items are missing.
Section 2 Comprehensive Modem Installation Instructions
Section 2.1 Modem Installation
This section will provide instructions for the installation of your modem. There are hardware installation and
system setup two parts for the modem. The modem hardware must be installed into the computer c orrectly
before you start the system setup.
Section 2.2 Hardware Installation
Please refer to Fig. 2 - 1 and proceed to following steps for how to insert your modem into the computer and
connect telephone wire and audio accessories.
Figure 2-1 Internal modem figure
1. Turn off and unplug your computer from the AC outlet.
2. Unplug any peripheral devices (keyboard, monitor, etc.) from your computer to avoid the
ri s k o f electric shock.
3. Take the cover off your computer, review computer's manual if you need further instructions.
4. Find an empty PCI slot.
5. Unscrew the PCI slot bracket and save the screw, then remove the bracket.
6. Plug the modem into the PCI slot carefull y until the modem is properly seated.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
- 2 - Rev.1.00.2.1.34
7. Fasten the modem bracket firmly with the screw saved in step 5.
8. Reassemble your computer cover and re-plug cables for peripheral.
9. Plug one end of telephone cord into the "LINE" jack at the modem's bracket. Plug another end of the
telephone cord into the telephone wall jack
10. So me models may compri se a phone jack for an optio nal teleph one. If you wish to u se a phone throug h
the same telephone wall jack when the modem is not in use, pl ug the telephone cord of the phone into
"PHONE" jack at the modem's bracket now. Lift the handset and listen for a dial tone to check for a
properly connection.
11. Plug the power cord into the computer and turn the computer on.
12. Up to now, the hardware installation has been finished. If you have not encounte red any problems, you
can go to Section 2.3 System Setup. If you are having problems, see Section 3 Troubleshooting.
NOTE : The telephone wall jack you use must be for an ANALOG phone line (the type found in most homes).
Many offices are equipped with digital phone lines. Please be sure you know which type of line you have. The
modem will be damaged if you use a digital phone line.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
- 3 - Rev.1.00.2.1.34
Section 2.3 System Setup
Section 2.3.1 Setup instructions for Windows 98
STEP 1. After you complete the modem hardware installation and turn on your PC, Windows system will
automatically detect your new added devices. Windows system will prompt you with an Add New
Hardware Wizard.
Then click on Cancel.
STEP 2. Insert the Modem Driver CD-ROM disk attached with your modem into the CD-ROM drive device,
Then run <CD-ROM letter>:\drivers\Win98\Setup.exe as shown in figure.
Then click on OK
STEP 3. And then, a prompt screen will ask you to ensure to install the modem driver.
Then click OK.
The setup utility will copy the needed files into windows system.
STEP 4. If there is no error message while the system is installing, your modem has been set up properly
and functionally.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
- 4 - Rev.1.00.2.1.34
Section 2.3.2 Uninstall Modem from Windows 98
STEP 1. Open Control Panel window, then click Add/Remove Programs icon.
STEP 2. Choose Agere Systems PCI Soft Modem device in stall/Uninstall tab,
then click on
Add/Remove… .
STEP 3. Click Yes to ensure to remove Agere Systems PCI Soft Modem device and its drivers.
STEP 4. Click Yes to restart your computer for all of the changes to take effect.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
- 5 - Rev.1.00.2.1.34
Section 2.3.3 Setup instructions for Windows Me
STEP 1. After you complete the modem hardware installation and turn on your PC, Windows system will
automatically detect and install your new added devices. Windows system will prompt you with an
Add New Hardware Wizard.
Click on Cancel.
STEP 2. Insert the Modem Driver CD-ROM disk attached with your modem into the CD-ROM drive device,
then run <CD-ROM letter>:\drivers\WinMe\SETUP.EXE to upgrade the modem driver as shown
in figure.
Then click on OK.
STEP 3. And then, a prompt screen will ask you to ensure to install the modem driver.
Then click OK.
The setup utility will copy the needed files into windows system.
STEP 4. If there is no error message while the system is installing, your modem has been set up properly
and functionally.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
- 6 - Rev.1.00.2.1.34
Section 2.3.4 Uninstall Modem from Windows Me
STEP 1. Open Control Panel window, then click on Add/Remove Programs icon.
STEP 2. Choose Agere Systems PCI Soft Modem device in Install/Uninstall tab, then click on
Add/Remove...
STEP 3. Click Yes to ensure to remove Agere Systems PCI Soft Modem device and its drivers.
STEP 4. Click Yes to restart your computer for all of the changes to take effect.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
- 7 - Rev.1.00.2.1.34
Section 2.3.5 Setup instructions for Windows 2000
STEP 1. After you complete the modem hardware installation and turn on your PC, Windows system will
automatically detect your new added devices. Windows system will prompt you with an Add New
Hardware Wizard.
Click on Cancel.
STEP 2. Insert the Modem Driver CD-ROM disk attached with your modem into the CD-ROM drive device,
then run <CD-ROM letter>:\drivers\Win2K&XP\Setup.exe as shown in figure.
Then click on OK.
STEP 3. And then, a prompt screen will ask you to ensure to install the modem driver.
Then click on OK.
The setup utility will copy the needed files into windows system.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
- 8 - Rev.1.00.2.1.34
STEP 4. The prompt screens will be warning you that the digital signature of programs have not found as
shown in figure.
Please always click on Yes.
STEP 5. If there is no error message while the system is installing, your modem has been set up properly
and functionally.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
- 9 - Rev.1.00.2.1.34
Section 2.3.6 Uninstall Modem from Windows 2000
STEP 1. Open Control Panel window and choose Add/Remove Programs icon.
STEP 2. Select Agere Systems PCI Soft Modem device in Change or Remove Programs tab, then click
on Change/Remove.
STEP 3. Click Yes to ensure to remove Agere Systems PCI Soft Modem device and its drivers.
STEP 4. Click Yes to restart your computer for all of the changes to take effect.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
- 10 - Rev.1.00.2.1.34
Section 2.3.7 Setup instructions for Windows XP
STEP 1. After you complete the modem hardware in stallation and turn on your PC, Windows system will
automatically detect and install your new added devices. Windows system will prompt you with an
Add New Hardware Wizard.
Click on Cancel.
STEP 2. Insert the Modem Driver CD-ROM disk attached with your modem into the CD-ROM drive device,
Then run <CD-ROM letter>:\Drivers\Win2K&XP\SETUP.EXE to upgrade the modem driver as
shown in figure.
Then click on OK.
STEP 3. And then, a prompt screen will ask you to ensure to install the modem driver.
Then click OK.
The setup utility will copy the needed files into windows system.
Loading...