This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
zConsult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands
are country dependent and are firmware programmed at the factory to match
- 2 -
the intended destination. The firmware setting is not accessible by the end
user.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the R&TTE Directive
1999/5/EC:
- EN60950-1:2006
Safety of Information Technology Equipment
- EN50385 : (2002-08)
- Product standard to demonstrate the compliance of radio base stations and fixed
terminal stations for wireless telecommunication systems with the basic
restrictions or the reference levels related to human exposure to radio frequency
electromagnetic fields (110MHz - 40 GHz) - General public
- EN 300 328 V1.7.1: (2006-10)
- Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband
Transmission systems; Data transmission equipment operating in the 2,4 GHz
ISM band and using spread spectrum modulation techniques; Harmonized EN
covering essential requirements under article 3.2 of the R&TTE Directive
- EN 301 489-1 V1.8.1: (2008-04)
- Electromagnetic compatibility and Radio Spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services;
Part 1: Common technical requirements
- EN 301 489-17 V1.3.2 (2008-04)
- Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17:
Specific conditions for 2,4 GHz wideband transmission systems, 5 GHz high
performance RLAN equipment and 5,8 GHz Broadband Data Transmitting
Systems
-
This device is a 2.4 GHz wideband transmission system (transceiver), intended for
use in all EU member states and EFTA countries, except in France and Italy where
restrictive use applies.
- 3 -
In Italy the end-user should apply for a license at the national spectrum authorities in
order to obtain authorization to use the device for setting up outdoor radio links and/or
for supplying public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some
areas the RF output power may be limited to 10 mW EIRP in the frequency range of
2454 – 2483.5 MHz. For detailed information the end-user should contact the national
spectrum authority in France.
0560
- 4 -
Česky
[Czech]
Dansk
[Danish]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se
základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja
nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English Hereby, [name of manufacturer], declares that this [type of equipment] is in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones
Ελληνική
[Greek]
Français
[French]
Italiano
[Italian]
Latviski
[Latvian]
Lietuvių
[Lithuanian]
aplicables o exigibles de la Directiva 1999/5/CE.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment]
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est
conforme aux exigences essentielles et aux autres dispositions pertinentes de la
directive 1999/5/CE.
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio]
è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla
direttiva 1999/5/CE.
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un
citiem ar to saistītajiem noteikumiem.
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in
Nederlands
[Dutch]
overeenstemming is met de essentiële eisen en de andere relevante bepalingen
van richtlijn 1999/5/EG.
- 5 -
Malti
[Maltese]
Magyar
[Hungarian]
Polski
[Polish]
Português
[Portuguese
]
Slovensko
[Slovenian]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma
mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó
alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z
zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami
Dyrektywy 1999/5/EC.
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com
os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a
Slovensky
[Slovak]
Suomi
[Finnish]
Svenska
[Swedish]
European Union Notice:
Radio products with the CE marking comply with the R&TTE Directive
(1999/5/EC), the EMC Directive (89/336/EEC) and the Low Voltage Directive
(73/23/EEC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European
všetky príslušné ustanovenia Smernice 1999/5/ES.
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen
tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja
sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med
de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår
av direktiv 1999/5/EG.
Norms:
z EN 60950 Product Safety
z EN 300 328 Technical requirement for radio equipment
z EN 301 489-1/-17 General EMC requirements for radio equipment
- 6 -
Tradema rk recognition
All product names used in this manual are the properties of their respective owners and
are acknowledged.
- 7 -
Table of Contents
Table of Contents...................................................................................................................................... 8
1. Getting Started with the TEW-647GA ..............................................................................................10
A ........................................................................................................................................................... 45
B ........................................................................................................................................................... 46
8
C ........................................................................................................................................................... 47
D ........................................................................................................................................................... 47
G ........................................................................................................................................................... 49
H ........................................................................................................................................................... 50
I ............................................................................................................................................................. 50
K ........................................................................................................................................................... 52
N ........................................................................................................................................................... 53
O ........................................................................................................................................................... 54
R ........................................................................................................................................................... 56
U ........................................................................................................................................................... 59
W ..........................................................................................................................................................60
Congratulations on purchasing the TEW-647GA! This manual provides information for setting
up and configuring the TEW-647GA. This manual is intended for both home users and
professionals.
1.1. Package Contents
z TEW-647GA Wireless N Gaming Adapter
z CD-ROM (User’s Guide)
z Multi-Language Quick Installation Guide
z CAT-5 Ethernet Cable
z Power Adapter (12V, 0.5A)
Using a power supply with a different voltage than the one included with your
product will cause damage and void the warranty for this product.
1.2. Minimum System Requirements
Installation Requirements
z Web Browser: Internet Explorer (6 or higher) Mozilla or Safari.
z A computer with a network adapter or wireless adapter properly installed.
z CD-ROM drive
z A router with an available network LAN port.
z A RJ-45 network cable.
10
2. Introduction
The TEW-647GA Wireless N Gaming Adapter is an high-performance, supports high-speed
wireless networking at home, at work or in public places. This bridge is also back compatible
with 802.11g or 11b devices. This means that you do not need to change your entire network to
maintain connectivity. You may sacrifice some of 11n’s speed when you mix 11n and 11b/g
devices, but you will not lose the ability to communicate when you incorporate the 11n standard
into your 11b/g network. You may choose to slowly change your network by gradually replacing
the 11b/g devices with 11n devices.
2.1. Features
• Wi-Fi compliant with IEEE 802.11n standard
• Backwards compatible with IEEE 802.11g and IEEE 802.11b devices
• Connects network-ready game consoles including Nintendo Wii, Xbox,
Xbox 360, PlayStation 2 and PlayStation 3 to a high speed wireless n
network
• Easy setup with Wi-Fi Protected Setup (WPS) feature
• Maximum reliability, throughput and connectivity with automatic data rate
switching
• Supports 64/128-bit WEP, WPA/WPA2 and WPA-PSK/WPA2-PSK
• Low interference and high susceptibility optimize performance
• Easy user setup wizard and intuitive Web browser configuration
• Coverage of up to 50 meters indoor, 100 meters outdoor *
11
3. Hardware Overview
3.1. LED Indications
12
3.2. Rear Panel
3.3 Top View
3.4 Bottom View
13
3.3 Installation Considerations
The TEW-647GA Gaming Adapter allows you to access your network by using a wireless
connection from virtually anywhere within its operating range. Keep in mind that the
number, thickness and location of walls, ceilings, or other objects that the wireless
signals must pass through, may limit the range. Typical ranges vary depending on the
types of materials and background RF (radio frequency) noise in your home or business.
The key to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the TEW-647GA and other network
devices to a minimum - each wall or ceiling can reduce your wireless product’s range
from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or
ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5
meters), at a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a
2-degree angle it looks over 42 feet (14 meters) thick! Position devices so that the
signal will travel straight through a wall or ceiling (instead of at an angle) for better
reception.
3. Building Materials can impede the wireless signal - a solid metal door or aluminum
studs may have a negative effect on range. Try to position wireless devices and
computers with wireless adapters so that the signal passes through drywall or open
doorways and not other materials.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or
appliances that generate extreme RF noise.
14
3.4 Getting Start
1. Insert Setup Wizard CD into your CD-ROM drive.
2. The Welcome screen appears on your monitor. Click Setup Wizard button.
3. Read the License Agreement, accept the terms and click Next to continue the installation.
15
4. Connect an Ethernet cable from the LAN port on your PC to the LAN port on the
TEW-647GA, click Next to continue.
5. Plug in the power adapter and verify the Power & Ethernet LEDs are light.
16
6. The search window will detect the connected TEW-647GA on our pc and display
information here. Click Configure to continue (default TEW-647GA IP Address is
192.168.10.110).
7. Enter the password for TEW-647GA the click Login. The default password is “blank”.
17
8. To change new password, please enter the new password below then click Change.
Note: To continue without changing the password, please click on the Skip button
9. There are 2 options to configure this adapter, WPS (Wi-Fi Protected Setup) or Manual
Setup. To setup with WPS method, continue to step 10 or to perform a Manual setup,
please go to step 14.
10. You can choose to use Push Button Method (PBC) or PIN Method to connect to your
existing wireless network using WPS type connection.
18
When selecting PBC method, once the Enable WPS is clicked, also press the WPS on
your wireless router, the devices would negotiate and connection automatically.
When using the PIN Method, please enter the Device PIN number on your router and save
it. Use Site Survey button to find the router you would like to connect then click Enable WPS, then devices would negotiate and connect.
Note: when the WPS has solid led on TEW-647GA, it means the connection has
established, otherwise, please try again.
19
11. When the connection is made, it is recommended that you save or print your wireless
settings with the Save or Print buttons. Click Apply to continue.
12. Disconnect the Ethernet cable from your PC to the destination game console.
13. Congratulations you have configured you TEW-647GA.
20
Loading...
+ 44 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.