Una unidad de CD-ROM
Un PC con puerto USB disponible
Windows 98SE/ME/2000/XP
Aplicación
Contenidos del paquete
TEW-604UB
Guía de instalación rápida
CD-ROM del controlador y la
herramienta
Cable de USB
Workstation with
108Mbps Smart Wireless
USB 2.0 Adapter
(TEW-604UB)
Workstation with
Wireless PCI Adapter
108Mbps
(TEW-603PI)
USB108Mbps Wireless
108Mbps Wireless Router
Español
Notebook with
108Mbps Smart Wireless
USB 2.0 Adapter
(TEW-604UB)
(TEW-611BRP)
1
Internet
Cable/DSL
Modem
2. Cómo se instala
¡Importante! NO conecte el adaptador USB inalámbrico a su PC a menos que
se le indique.
Para usuarios de Windows
1. Introduzca el CD-ROM del
controlador y de la herramienta
en la unidad de CD-ROM de su PC
y luego haga clic en Install Utility
(Instalar herramienta).
2. Siga las instrucciones del
InstallSheild Wizard (asistente de InstallSheild) y luego haga clic en
Finish (Finalizar).
2
Español
Nota: El TEW-604UB es hot pluggable, puede conectarse o desconectarse con
el PC encendido. Tras introducir el TEW-604UB en uno de los puertos USB, le
aparecerá el mensaje Found New Hardware (Nuevo hardware encontrado).
3. Conecte el adaptador USB
inalámbrico TEW-604UB al puerto
USB de su PC.
4. Luego, aparecerá la ventana
Found New Hardware Wizard
(Asistente para nuevo hardware
encontrado), seleccione No, y
después haga clic en Next
(Siguiente).
5. Haga click en Next (Siguiente).
Español
3
6. Luego le aparecerá un mensaje
de advertencia. Haga clic en
Continue Anyway (Continuar de
todas formas).
7. Haga clic en Finish (Finalizar).
La instalación ha sido completada
Nota: Una vez completada la instalación, le aparecerá el icono inalámbrico en
la bandeja de su sistema (próximo al reloj en la esquina derecha inferior de su
pantalla). Si no le aparece, entonces reinicie su PC. Vaya a la Configuración
Inalámbrica en la sección 4 para configurar el TEW-604UB.
4
Español
3. Configuración inalámbrica
Nota: Una configuración inalámbrica requiere un Punto de Acceso 802.11g ó
802.11b (para Modo de Infraestructura) u otro adaptador inalámbrico 802.11g
(para un modo de red Ad-Hoc o de Usuario a Usuario).
1. Haga doble clic en el icono
inalámbrico del PC en la bandeja
del sistema .
2. Haga clic en Profile (Perfil) y
después pulse Add (Añadir).
3. Haga clic en Browse (Examinar).
4. Haga doble clic en el SSID que
coincida con su punto de acceso
inalámbrico.
5
Español
5. Haga click en Next (Siguiente).
6. Seleccione la Security (Seguridad)
que corresponda a su red
inalámbrica y luego haga clic en
Next (Siguiente).
Nota: Si su red inalámbrica tiene seguridad inalámbrica, entonces la Wireless Client Utility (Herramienta para cliente inalámbrico) le pedirá que introduzca
las configuraciones de seguridad inalámbrica antes de continuar con los pasos
a continuación. Consulte la Guía del Usuario para más información sobre su
seguridad inalámbrica.
7. Compruebe las Advanced
Settings (Configuraciones
avanzadas) y el Wireless Mode
(Modo inalámbrico), después pulse
Next (Siguiente).
6
Español
8. Haga clic en Activate Now
(Activar ahora).
9. Compruebe que el Link Status
(Estatus del enlace) esté
conectado.
La instalación ha sido completada
Para obtener información más detallada sobre la configuración así como de las
configuraciones avanzadas del TEW-604UB , por favor consulte la sección de
resolución de problemas, el CD-ROM de la Guía del Usuario, o el sitio Web de
Trendnet en http://www.trendnet.com.
7
Español
Troubleshooting
I inserted the Utility & Driver CD-ROM into my computer's CD-ROM Drive and the
Q1:
installation menu does not appear automatically. What should I do?
Q2:
isn't connecting to my access point. What should I do?
Q3:
Q4:
If you still encounter problems or have any questions regarding the TEW-604UB, please refer to
the User's Guide included on the Utility & Driver CD-ROM or contact Trendnet's Technical Support
Department.
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may cause
undesired operation.
If the installation menu does not appear automatically, click Start, click Run, and type
A1:
D:\Autorun.exe where "D" in "D:\Autorun.exe" is the letter assigned to your computer's CD-
ROM Drive. And then click OK to start the installation.
I completed all the steps in the Quick Installation Guide, but my Wireless USB Adapter
First, verify that the Network Name (SSID) matches your wireless router or wireless
A2:
access point's SSID. Second, you should check your TCP/IP properties to ensure that Obtain
an IP address automatically is selected. Third, you can click on the Site Survey tab of the
Wireless Client Utility to check and see if there are any available wireless networks listed.
Windows is unable to recognize my hardware. What should I do?
Make sure your computer meets the minimum requirements as specified in Section 1 of
A3:
this Quick Installation Guide. Also make sure that you install the Wireless Client Utility
(as described in Section 2) before connecting the Wireless USB Adapter. If Windows is still
unable to recognize your hardware, try installing the Wireless USB Adapter to a different
USB port of your computer.
I cannot open the Wireless Configuration Utility. What should I do?
Go to your Device Manager to make sure the adapter is installed properly. If you see a
A4:
networking device with a yellow question mark or exclamation point, you will need to reinstall
the device and/or the drivers. To access your Device Manager, right-click My Computer, click
Properties, click the Hardware tab, and then click Device Manager.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.