TREND WS-S, WS-SD User Manual

Wind Speed and Direction Sensor

Important: Retain these instructions

UNPACKING

Installation

Dimensions

1

M8 mounting stud

Installation Instructions

WS/S, /SD

WS/S, /SD
Installation
Instructions
TG102613

130 mm (5.12”)

sensor cable
supplied
(3 m, 9’ 10”,
length)

Requirements

2

a
b Location

Choose location where wind speed is
representative of area to be measured

if required to use on horizontal rail
(i) remove bracket

WS/S, /SD Installation Instructions TG102613 Issue 2/C 08/01/07

-20 °C
(-4 °F)

+70 °C

(158 °F)

WS/S, /SD Data
Sheet TA102481

220 mm (8.66”)

260 mm (10.23”)

95 mm (3.74”)

Change bracket fixing

3

(if required for horizontal rail)

Elbows supplied
configured for vertical
mast

(ii) fix bracket for horizontal rail

1

WS/S, /SD Installation Instructions
Installation (continued)

Fit plastic insulator strips

4

(i) vertical mast

plastic
insulator
strips

Fit elbow to mast or rail

5

vertical rail horizontal rail

(ii) horizontal rail

plastic
insulator
strips

Fit sensor to elbow

6

vertical

7

Align sensor

N

tighten lock nut

2

WS/S, /SD Installation Instructions TG102613 Issue 2/C 08/01/07

Installation Instructions WS/S, /SD

I Q 3

Installation (continued)

Connect to IQ

8

IQ1, IQ2

W S / S , / S D

W / S D

IQ3

W S / S , / S D

w i n d s p e e d

W / S D

w i n d d i r e c t i o n

Cable is 3 m (9’ 10”) long. If required
to extend:

Configure IQ

9

or

I Q

G n ( 1 )
B k ( 2 )

W ( 3 )
B k ( 4 )

R ( 5 )
B k ( 6 )

G n ( 1 )
B k ( 2 )

W ( 3 )
B k ( 4 )

R ( 5 )
B k ( 6 )

Input channel
linked for digital

I Q 1 , I Q 2 5 1

2 4 V
I N

x
x

I N
0 V

input (D)

I Q 2

( e x c lu d i n g I Q 2 5 1 )

I N ( + 5 V )
C

Input channel
linked for

D

T

thermistor (T)

I Q 3

+ ( 2 4 V )
N ( in )

0 ( 0 V )
x
x

+ ( 2 4 V )

N ( i n )

0 ( 0 V )

Universal Input
channel linked for
digital input (D)

Digital
input
channel

Input channel
linked for
thermistor (T)

D

T

WS/S, /SD Data Sheet TA102481

I Q

IQ Configuration
Manual 90-1533

10

Set up IQ Sensor Type (for wind speed sensor input)

It is recommended to use SET (Software Tool) for the setting of the sensor type module.
For all IQ2 series controllers with firmware version 2.1 or greater, or IQ3 series controllers,
the following SET Unique Sensor Reference should be used:

Wind Direction Therm

Alternatively used sensor scaling mode 5, characterise, and enter scaling manually as
defined in the table below:
For all other IQ controllers see WS/S, /SD Data Sheet TA102481.

tYpe Sensor digI/P Driver Function loGic Loop scHedule seQnc Analog
digBit Knob sWitch Time Zone Oss User addRess intcoN calarM reView Plot
calEndar

= ?

Yn<CR>
TYPE n
:=?
S=5 (characterise)
Y= , E= , U= , L= , P=

I1 to I3, O1 to O3=

X <CR>

WS/S, /SD Installation Instructions TG102613 Issue 2/C 08/01/07

Y

E

U

L

P

x
1
2
3

epyttupni

tnenopxE4

reppU083

rewoL1-

stnioP3

xIxO

00

99.0753
001953

3

)smhokrotsimreht(

3

WS/S, /SD Installation Instructions

s

Installation (continued)

Set up IQ Wind

11

Direction Strategy

For IQ1xx, IQ2xx (<v5.1) only

see WS/S, /SD Data Sheet
TA102481

13

Test System

Δ V

Δ D

N

EW

S

Set up IQ Wind Speed Strategy

12

W i n d S p e e d

1 , 0

1

3 4

G 1

F = 1

S

S T = 6 0

C O U N T E R

r e s e t

9 3

R

M

1 . 4 9 3

9 4

For S17 to be in feet/second
set F14(F) to 4.75.

3 5

6 0

F 1 4

E

G
F

D I V

D = F ( G / E )

1 1 4

D

The diagram shows digital input 1 being used; the strategy
should be changed to match the actual input channel used.

14

Check Sensor Alignment

if greater accuracy required

N

IQ

3 6

W i n d S p e e d

i n m /

S 1 7

IQ

Δ D=360°/0°

Disposal

WEEE Directive :

At the end of their useful life the packaging
and product should be disposed of by a

Do not dispose of with normal household waste.
Do not burn.

Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route
du Bois 37,Switzerland by its Authorized Representative.

Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof
without obligation to notify any person of such revisions or changes.

Trend Control Systems Limited

P.O. Box 34, Horsham, West Sussex, RH12 2YF, UK. Tel:[phone] Fax:[phone] www.trend-controls.com

Trend Control Systems USA

6670 185th Avenue NE, Redmond, Washington 98052, USA. Tel: [phone], Fax: [phone] www.trend-controls.com

4

suitable recycling centre.

WS/S, /SD Installation Instructions TG102613 Issue 2/C 08/01/07