TREND VJS/TG/JIG User Manual

VJS/TG/JIG

Please read these instructions before use.

VJS/TG/JIG

Dear Customer

Thank you for purchasing this Trend product, we
hope you enjoy many years of creative and
productive use.

Please remember to return your guarantee card
within 28 days of purchase.

CONTENTS

TECHNICAL DATA _____________________1
SAFETY ____________________________2-3
ITEMS ENCLOSED ____________________4
DESCRIPTION OF PARTS _______________5
ASSEMBLY & ADJUSTMENT

– Corner Brackets _____________________6
– Sliding Stops ________________________6
– Squaring Plate ______________________6
– Clamping Plate ______________________6
– Bottom Squaring Plate ________________6
– Adjustment _________________________7
– Setting Jig Squareness ________________7
– User Made Spelch Block _______________7

OPERATION

– Adjusting Frame for Size _______________8
– Clamping ___________________________8
– Trimming/Cross-cutting with a Router/Saw _8
– Grooving with the Router _____________8-9
– Cross Cutting with a Router____________10
– Cross Cutting with a Saw______________11

ACCESSORY ________________________11
MAINTENANCE ______________________11
ENVIRONMENTAL PROTECTION________11
GUARANTEE ________________________11
SPARE PARTS

– Spare Parts List _____________________12
– Spare Parts Diagram _________________IB

TECHNICAL DATA

Extrusion thickness 15.8mm
Extrusion width 54.0mm
Working groove length 400mm
Maximum width adjustment 70mm
Weight 1.9kg

The following symbols are used throughout this
manual:

Denotes risk of personal injury, loss of
life or damage to the tool in case of non­observance of the instructions in this
manual.

Refer to the instructions manual or your
power tool.

This unit must not be put into service until it has
been established that the power tool to be
connected to this unit is in compliance with
2006/42/EC (identified by the CE marking on the
power tool).

INTENDED USE

This accessory is designed to be used with a
router with a suitable cutter and guide bush fitted
to groove and trench natural timber and boards.
The accessory can also be used with a jigsaw or
circular saw to crosscut boards.

☎

If you require further safety advice,
technical information or spare parts,
please call Trend Technical Support
or visit www.trend-uk.com

-1-

VJS/TG/JIG

SAFETY

WARNING:

Observe the safety regulations in the
instruction manual of the power tool to be
used. Please read the following
instructions carefully. Failure to do so
could lead to serious injury. When using
electric tools, basic safety precautions,
including the following should always be
followed to reduce the risk of fire, electric
shock and personal injury. Also observe
any applicable additional safety rules.
Read the following safety instructions
before attempting to operate this product.

PLEASE KEEP THESE
INSTRUCTIONS IN A SAFE PLACE.

The attention of UK users is drawn to The
Provision and Use of Work Equipment
Regulations 1998, and any subsequent
amendments.

Users should also read the HSE/HSC
Safe Use of Woodworking Machinery
Approved Code of Practice and Guidance
Document and any amendments.

Users must be competent with
woodworking equipment before using our
products.

IMPORTANT NOTE:

Residual Risk. Although the safety
instructions and operating manuals for
our tools contain extensive instructions on
safe working with power tools, every
power tool involves a certain residual risk
which cannot be completely excluded by
safety mechanisms. Power tools must
therefore always be operated with
caution!

General

1. Disconnect power tool and attachment

from power supply when not in use,
before servicing, when making
adjustments and when changing
accessories such as cutters. Ensure
switch is in “off” position. Always
ensure cutter has stopped rotating.

2. Always mount the power tool,

accessory or attachment in conformity
with the instructions. Only use
attachment and accessories specified
in the power tool manual. The tool or
attachment should not be modified or
used for any application other than
that for which it was designed. Do not
force tool.

3. Keep children and visitors away. Do

not let children or visitors touch the
tool, accessory or attachment. Keep
children and visitors away from work
area. Make the workshop child proof
with padlock and master switch.

4. Dress properly. Do not wear loose

clothing or jewellry, they can be
caught in moving parts. Rubber
gloves and non-skid footwear is

recommended when working
outdoors. Wear protective hair
covering to contain long hair.

5. Consider working environment. Do

not use the product in the rain or in a
damp environment. Keep work area
well lit. Do not use power tools near
gasoline or flammable liquids. Keep
workshop at a comfortable
temperature so your hands are not
cold. Connect machines that are used
in the open via a residual current
device (RCD) with an actuation
current of 30 mA maximum. Use only
extension cables that are approved for
outdoor use.

6. The accessory or attachment must be

kept level and stable at all times.

7. Keep work area clean. Cluttered

workshops and benches can cause
injuries. Ensure there is sufficient
room to work safely.

8. Secure idle tools. When not in use,

tools should be stored in a dry and
high or locked up place, out of reach
of children.

9. For best control and safety use both

hands on the power tool and
attachment. Keep both hands away
from cutting area. Always wait for the
spindle and cutter to stop rotating
before making any adjustments.

10. Always keep guards in place and in

good working order.

11. Remove any nails, staples and other

metal parts from the workpiece.

12. Maintain tools and cutters with care.

Keep cutters sharp and clean for
better and safer performance. Do not
use damaged cutters. Follow
instructions for lubricating and
changing accessories. Keep handles
dry, clean and free from oil and
grease.

13. Maintain accessories. Do not use

damaged accessories. Only use
accessories recommended by the
manufacturer.

14. Check damaged parts. Before

operation inspect the attachment, the
power tool, the cable, extension cable
and the plug carefully for signs of
damage. Check for alignment of
moving parts, binding, breakage,
mounting and any other conditions
that may effect its operation. Have any
damage repaired by an Authorised
Service Agent before using the tool or
accessory. Protect tools from impact
and shock.

15. Do not use tool if switch does not turn

it on or off. Have defective switches
replaced by an Authorised Service
Agent

16. Don't over reach. Keep proper footing

-2-

and balance at all times. Do not use
awkward or uncomfortable hand
positions.

17. Don’t abuse the cable. Never carry

power tool or accessory by cord or
pull it to disconnect from the socket.
Keep cord from heat, oil and sharp
edges. Always trail the power cord
away from the work area.

18. Connect dust extraction equipment.

If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used.

19. Check all fixing and fastening nuts,

bolts and screws on power tool,
attachment and cutting tools before
use to ensure they are tight and
secure. Periodically check when
machining over long periods.

20. Stay alert. Watch what you are doing.

Use common sense. Do not operate
tools when you are tired, under the
influence of drugs or alcohol.

21. Personal Protective Equipment (PPE)

for eye, ear and respiratory protection
must be worn. All PPE must meet
current UK and EU legislation.

22. Do not leave tools running

unattended. Do not leave tool until it
comes to a complete stop.

23. Always clamp workpiece being

machined securely.

24. Only use cutting tools for

woodworking that meet EN847-1/2
safety standards, and any
subsequent amendments.

25. Vibration levels. Hand held power

tools produce different vibration
levels. You should always refer to the
specifications and relevant Health &
Safety Guide.

Routing Safety

1. Read and understand instructions

supplied with power tool, attachment
and cutter.

2. Keep hands, hair and clothing clear of

the cutter.

3. Remove adjusting keys and

spanners. Check to see that keys
and adjusting spanners are removed
from the router tool, cutter and
attachment before turning router on.
Make sure cutter can rotate freely.

4. Noise. Take appropriate measures

for the protection of hearing if the
sound pressure of 85dB(A) is
exceeded. Routing sound pressure
may exceed 85dB(A), so ear
protection must be worn.

5. Eye protection. Always wear eye

protection in the form of safety
goggles, spectacles or visors to
protect the eyes.

VJS/TG/JIG

6. Respiratory protection. Wear a face

or dust mask, or powered respirator.
Dust masks/filters should be changed
regularly.

7. Do not switch router on with the cutter

touching the workpiece. At the end of
the cut, release the router plunge and
allow spindle to stop rotating. Never
use the spindle lock as a brake

8. The direction of routing must always

be opposite to the cutter's direction of
rotation. Do not back-cut or climb-cut.

9. Check before cutting that there are no

obstructions in the path of the router.
Ensure there are no obstacles
beneath workpiece when cutting full
thickness, and that a sacrificial work
surface is used.

Router Cutter Safety

1. Cutting tools are sharp. Care should

be taken when handling them. Do not
drop cutters or knock them against
hard objects. Handle very small
diameter cutters with extra care.
Always return cutter to its packaging
after use.

2. Always use cutters with a shank

diameter corresponding to the size of
the collet installed in your tool.

3. The maximum speed (n.max) marked

on the tool, or in instructions or on
packaging shall not be exceeded.
Where stated the speed range shall
be adhered to. Recommended speeds
are shown in the Trend Routing
Catalogue and/or website.

4. Always use router cutters in a router.

Drill and boring bits must not be used
in a router. Router cutters must only
be used for the material cutting
application for which they are
designed. Do not use on metal or
masonry.

5. Never use cutters with a diameter

exceeding the maximum diameter
indicated in the technical data of the
powertool or attachment used.

6. Before each use check that the cutting

tool is sharp and free from damage.
Do not use the cutting tool if it is dull,
broken or cracked or if in any other
damage is noticeable or suspected.

7. Cutters should be kept clean. Resin

build up should be removed at regular
intervals with Resin Cleaner
use of a PTFE dry lubricant will
reduce resin build up. Do not use
PTFE spray on plastic parts.

8. When using stacked tooling (multi-

blade, block and groover etc.) on a
spindle arbor, ensure that the cutting
edges are staggered to each other to
reduce the cutting impact.

9. Cutter shanks should be inserted into

the collet all the way to the line

®

. The

indicated on the shank. This ensures
that at least
held in the collet. Ensure clamping
surfaces are cleaned to remove dirt,
grease, oil and water.

10. Observe the correct assembly and

fitting instructions in the router
instruction manual for fitting the collet,
nut and cutter.

11.Tool and tool bodies shall be clamped

in such a way that they will not
become loose during operation. Care
shall be taken when mounting cutting
tools to ensure that the clamping is by
the shank of the cutting tool and that
the cutting edges are not in contact
with each other or with the clamping
elements.

12. It is advisable to periodically check

the collet and collet nut. A damaged,
worn or distorted collet and nut can
cause vibration and shank damage.
Do not over-tighten the collet nut

13. Do not take deep cuts in one pass;

take several shallow or light passes to
reduce the side load applied to the
cutter and router. Too deep a cut in
one pass can stall the router.

15. In case of excessive vibrations whilst

using the router stop immediately and
have the eccentricity of the router,
router cutter and clamping system
checked by competent personnel

15. All fastening screws and nuts should

be tightened using the appropriate
spanner or key and to the torque
value provided by the manufacturer.

16. Extension of the spanner or tightening

using hammer blows shall not be
permitted.

17.Clamping screws shall be tightened

according to instructions provided by
the manufacture. Where instructions
are not provided, clamping screws
shall be tightened in sequence from
the centre outwards.

3

⁄4of the shank length is

Using Routers In A Fixed Position

1. Attention should be made to the

HSE’s Safe Use of Vertical Spindle
Moulding Machines Information Sheet
No.18 and any revisions.

2. After work, release the router plunge

to protect the cutter.

3. Always use a push-stick or push-block

when making any cut less than
300mm in length or when feeding the
last 300mm of the cut.

4. The opening around the cutter should

be reduced to a minimum using
suitably sized insert rings in the table
and closing the back fence cheeks or
fitting a false fence on the back fence.

5. Whenever possible use a work

-3-

holding device or jig to secure
component being machined. Ensure
any attachment is securely fitted to the
workbench, with table surface at
approximately hip height.

6. Use a No-Volt Release Switch. Ensure

it is fixed securely, easily accessible
and used correctly.

7. In router table (inverted) mode, stand

to the front right of the table. The
cutter will rotate anti-clockwise when
viewed from top so the feed direction
is from the right (against the rotation of
the cutter). In overhead mode, stand
to the front left of the machine table
and the feed direction is from the left.

8. Do not reach underneath table or put

your hands or fingers at any time in
the cutting path while tool is connected
to a power supply.

9. Never thickness timber between the

back of the cutter and the backfence.

Useful Advice When Routing

1. Judge your feed rate by the sound of

the motor. Feed the router at a
constant feed rate. Too slow a feed
rate will result in burning.

2. Trial cuts should be made on waste

material before starting any project.

3. When using some attachments e.g. a

router table or dovetail jig, a fine
height adjuster is recommended.

4. When using a template guide bush,

ensure there is sufficient clearance
between cutter tip and inside edge of
bush and that it cannot come into
contact with collet and nut. Ensure
cutter and guide bush are concentric.

Router Cutter Repair/Maintenance

1. Repair of tools is only allowed in

accordance with the manufacturers
instructions.

3. The design of composite (tipped) tools

shall not be changed in process of
repair. Composite tools shall be
repaired by a competent person i.e. a
person of training and experience, who
has knowledge of the design
requirements and understands the
levels of safety to be achieved.

4. Repair shall therefore include, e.g. the

use of spare parts which are in
accordance with the specification of
the original parts provided by the
manufacturer.

5. Tolerances which ensure correct

clamping shall be maintained.

6. Care shall be taken that regrinding of

the cutting edge will not cause
weakening of the body and the
connection of the cutting edge to the
body.

Version 7.1 06/2006

VJS/TG/JIG

ITEMS ENCLOSED

Pre-assembled

x2

x2

x6

Pre-assembled

x8

Silver

x8

Black

x1

x1

x1

x1

x1

x1

x4 x4

Silver

x1

Pre-assembled

x2

Black x 10mm

x2

x1

End Cap

x2

x1

x2

x2

x1

x2

Silver

x6

x4

Black

x2

ITEMS REQUIRED

n Plunge router (or jigsaw/circular saw).

n 30mm guide bush with minimum 8mm

projection e.g. Ref. GB30/A.

n T-Square.

n Board with flat edge.

n Suitable router cutter.

n No. 2 Phillips screwdriver.

n Square and long rule/tape measure.

n Clamp x 2.

n Hand tools.

n User made MDF spelch block.

-4-

DESCRIPTION OF PARTS

VJS/TG/JIG

A Alloy extrusion long 430mm with scale

B Alloy extrusion short 310mm with end cap

C Bottom squaring butt

D Clamping plate

E Squaring plate

F T-nut

G Right-hand sliding stop

H Left-hand sliding stop

I Short T-nut

J Connector block

K Alloy extrusion short (no end cap)

L Alloy extrusion long 430mm (no scale)

M Corner bracket

P

O

E

F

D

L

N

O

N

F

F

N Machine screw M4 x 6mm (black-fixed)

O Machine screw M4 x 6mm (silver-adjustable)

P Machine screw M4 x 10mm (black-fixed for

clamping plate)

Q Machine screw UNC 5/16” x 5/8” for

squaring butt to connector plate

R Machine screw M5 x 20mm for spelch block

fixing

S Set screw for connecting block to extrusion

T Hex key 4mm A/F

U Hex key 6mm A/F

V Manual

F

G

H

I

I

F

I

F

B

A

M

R

K

T

J

C

S

Q

U

VJS/TG/JIG

V

-5-

VJS/TG/JIG

ASSEMBLY & ADJUSTMENT

Using the drawing on page 5 as a guide.

Corner Brackets

The T-nuts on the corner brackets are held by
silver screws, these will need to be removed and
the T-nut slid into the slot in the short extrusion
to assemble. The short T-nut must be positioned
nearest the end of extrusion.

Do not remove the T-nuts held by the
black screws onto the brackets.

n Slide the corner bracket assembly into the

open end of the long extrusion with scale
fitted, ensuring the T-nuts align with the slots
in the extrusion.

n Slide T-nut down until corner

bracket/squaring plate assembly stops, then
tighten the black screws with a No. 2 Phillips
screwdriver.

T-nut

Short
T-nut

Short
Extrusion

Sliding Stops

n Slide the right hand and left hand sliding stop

assembly into the bottom slot of the long
extrusion that does not have a scale.

n Slide sliding stop assemblies along the

extrusion by about 100mm and then lock into
position by tightening screws with a No. 2
Phillips screwdriver.

Squaring Plate

n Slide the squaring plate assembly into the

bottom slot of the short extrusion. Repeat for
other short extrusion. The end cap will need
to be removed.

n Place the ends of the long extrusion with the

corner bracket fitted onto the bottom slot (slot
towards centre of jig) of each short extrusion,
line up the T-nut and using the silver screw
join the corner bracket to the T-slot in the
extrusion.

Silver
screw

Long
Extrusion

Black
screw

n Lay all parts onto a workbench with the scale

side of the extrusions towards the centre.

Clamping Plate

The clamping plate is secured to the squaring
plate by two screws. Ensure the ends of the
small extrusions are sub-flush with the right hand
long extrusion.

The scale is self adhesive backed.
Only remove a 20mm section of the
self adhesive backing to ease
positioning of the scale.

-6-

VJS/TG/JIG

=

=

Make sure
the end of
the extrusion
is sub flush

Plan view of
assembled
jig

Make sure
the end of
the extrusion
is sub flush

Ensure all fixing screws are tight.

Bottom Squaring Butt

n Screw the set screw into the connecting

block using a 4mm A/F hex key. Repeat for
the other connecting block.

n Screw the connecting block onto the bottom

squaring butt using the socket head screw
and 6mm A/F hex key. Repeat for the other
connecting block.

Top

Connecting Block

Bottom
Squaring Butt

n With the M5 tapped holes of the bottom

squaring butt facing away from you, slide the
connecting block and butt assembly into the
end of the short extrusion without end caps.

Adjustment

The black screws are used to lock the brackets into
the extrusions. Once they are correctly fitted they
should not need to be adjusted. The silver screws
are the screws that allow for adjustment of the jig.

Setting Jig Squareness

n Place T-Square onto a flat board with a flat edge.

Place butt of T-Square against flat edge and
mark a pencil line along T-Square blade edge.

n Lay assembled jig onto board and butt the

bottom square butt against flat edge and check
inner edge of each long extrusion against pencil
line. Loosen screws and move long extrusion so
that they are parrallel to the pencil line and
tighten screws. Check squareness again.

User Made Spelch Block

To use the jig properly a user made sacrificial
spelch block should be made and fitted, this
prevents breakout on the back edge of the
component when cross cutting, as well as
allowing grooves to be cut to the end of the board
without damaging the jig. The spelch block should
be made from minimum 12mm thick MDF
(suggested 18mm thick), the length should be
about 350mm and 30mm high. Drill and
countersink two holes at 200mm centres to accept
M5 screws. The holes should be 7mm down from
one edge so that it will fit under the extrusion. The
countersink diameter should be 12.7mm. Screw
spelch block to bottom squaring butt using screws
supplied and Phillips No.2 screwdriver.

Spelch Block

200mm

350mm

Fixing screws

Min.

12mm

30mm

Top View

n Ensure the connecting block is flush with the

end of the extrusion and then tighten the set
screws with a 4mm A/F hex key.

Spelch block

Bottom squaring
butt

Certain extrusions are fitted with end
caps for protection. These can be
temporarily removed to allow
accessories to be slid onto the
extrusion but should always be refitted.

-7-

VJS/TG/JIG

OPERATION

Adjusting Frame for Size

n Loosen the silver screws.

n Set required size.

n Check jig for squareness with a T-Square and

flat board and adjust if necessary.

Another method to check squareness is to
measure across diagonals. If the measurement
is equal the frame is square, if the measurement
is out adjust as necessary.

The scales are for repetitive work and have
some lengthways adjustment to allow zero
setting.

Only loosen silver screws to adjust
frame.

After every adjustment, the frame
will need to be checked for
squareness.

Clamping

Always use a minimum of two clamps to hold the
jig to the component. Ensure the clamps will not
foul the saw or router. The jig has a clamping
plate to allow for the clamps to hold the jig.
A third clamp can also be used at the back of
the jig in some instances if component size
allows.

Third clamp
here if
possible

Guiding the Router/Saw

The jig can be used either with a router, or for
sawing using a jigsaw or circular saw.

n Router - to groove boards with a router fitted

with a guide bush with a minimum 8mm
projection. The guide bush follows the inside
of the extrusion. Adjustable stops can be set
to limit the length of the groove.
The flat side of the router base can also be
used against the edge of the right hand
extrusion for grooving, or trimming.

n Sawing - A jigsaw or circular saw can be

used against the edge of the right hand
extrusion to trim a board.

Grooving/Trenching/Tenon
Cutting with a Router

When grooving/trenching the router requires a
guide bush to be fitted which follows the inside
edge of the extrusion and guides the router.
The guide bush should have a spigot projection
of a minimum 8mm and suitable diameter to suit
the cutter. A recommended guide bush diameter
is 30mm. The difference between the cutter and
the guide bush is the offset. This offset will need
to be marked on the component to give the true
cut-line.

Varijig

Template guide bush

Guide bush ring

Cutter

Clamp here
ensure not
to foul the
router base

Component

Spelch block

Must
be 90º

-8-

Cutter and Guide
Bush Offset

Template

E

Guide bush
fitted to
router

FORMULA
(D- d)

d
D

E =

2

A recommended 30mm guide bush
should be used with a minimum 8mm
spigot projection e.g. Ref. GB30/A.

To rout grooves, trenches and tenon’s the router
base will sit on top of the extrusions, therefore
the maximum distance between the extrusion
should be 70mm so that both sides of the router
base are supported.
For grooves/trenches ensure that the straight
cutter has a smaller diameter that will pass
through the centre of the guide bush laving
enough clearance.

If using a router and guide bush with
router base sitting on top of the
extrusion, the maximum distance
between the extrusions is 70mm so
that both sides of the router base are
supported.

The trench/groove length can be limited by using
the sliding stops. To set the length stops
n Loosen both silver screws with a No.2 Phillips

screwdriver and slide the stops along the
extrusion to the required length. The offset
between the guide bush and cutter will need
to be catered for in the calculations.

n Once the sliding stops are in the correct

position tighten both screws on each stop to
lock in position.

VJS/TG/JIG

Grooving with the router

Component

Clamps

Side view of jig

Bottom squaring
block

Ensure working position is
comfortable.

Spelch block

Spelch
block

Jig

Component

The jig can also be used to cut tenons on timber.
This will require careful clamping to the
component. The component itself will require to
be clamped securely to the workbench. The other
end of the jig will need to be supported by a
waste piece of the same material of the same
thickness as the component.

Ensure the correct cutter diameter
will pass through the guide bush
leaving at least a 3mm clearance.

Check squareness of jig before use.

The material being cut will need to
be supported and clamped securely.

-9-

VJS/TG/JIG

Cross-cutting with a Router

The flat side of the router base can be used
against the edge of the right hand extrusion for
grooving or trimming. Ensure that the end of the
front and back short extrusions are not proud, so
they do not foul the base of the tool. The base
plate offset will need to be allowed for to give the
true cut line.

n Measure edge of left-hand router base plate

to right side of cutting edge, this will give the
offset.

Workpiece

X

X= Offset distance required from edge of
jig to edge of cutter.

n Mark cutline on the board and measure offset

to left of pencil line, at each end of line.

n Set right hand extrusion to offset line.

n Clamp jig using two or three clamps

n Set cutter depth.

n Plug in router, plunge down and rout across

board in a series of passes, until final depth
of cut is reached.

n Release plunge.

n Switch off router and remove.

n Remove clamps and jig from workpiece.

Crosscutting with the router

Component

Router up
against edge
of jig.

Spelch block

Clamps

When cutting tenons on narrow
materials, a waste piece of material of
the same thickness of the component
will be needed to support the other
end of the jig.

Check squareness of jig before use.

Ensure the jig sits and is clamped
properly to the component.

-10-

Cross-cutting with a Circular
Saw or Jigsaw

The edge of the jig is used to guide the base
plate of the saw. The base plate offset will need
to allowed for to give the true cut line. Ensure
that the end of the front and the back of the short
extrusion are not proud, so they do not foul the
base of the tool.

n Measure from the edge of left-hand side of

the saw base plate to right side of cutting
edge, this will give the offset.

VJS/TG/JIG

Check squareness of jig before use.

Ensure the jig is not clamped onto
the waste piece.

ACCESSORIES

Please use only Trend original accessories.

Ref. GB30A 30mm guide bush with 8mm

spigot length.

Workpiece

X

X= Offset distance required from
edge of jig to blade.

n Mark cut line on the board and measure offset

to left of pencil line, at each end of line.

n Set right hand extrusion to offset line.

n Clamp jig using two or three clamps

n Set blade depth of cut.

n Plug in saw and cut across the board.

n Release plunge.

n Switch off saw and remove.

n Remove clamps and jig from workpiece.

After use of the jig, keep assembled and store
properly.

Crosscutting with the saw

Component

Clamps

Spelch
block

Saw runs
against
edge of jig

MAINTENANCE

This jig has been designed to operate over a
long period of time with minimum of
maintenance. Continual satisfactory operation
depends upon proper tool care and regular
cleaning.

Cleaning

n Keep the grooves on the extrusion clear of

sawdust.

n Regularly clean the jig with a soft cloth.

Lubrication

n Your jig requires no additional lubrication.

Storage

n This jig should be safely stored on wall

hooks after use.

ENVIRONMENTAL
PROTECTION

Recycle raw materials instead of disposing
as waste.

Packaging should be sorted for environmental
friendly recycling. The product and its
accessories at the end of its life should be
sorted for environmental-friendly recycling.

GUARANTEE

The jig carries a manufacturers guarantee in
accordance with the conditions on the enclosed
guarantee card.

-11-

Please use only Trend original spare parts.

VJS/TG/JIG

VJS/TG/JIG - SPARE PARTS LIST

v1.0 08/2007

No. Qty. Desc. Ref.

1 12 Varijig T-Nut M4 WP-VJS/01

1A 6 Varijig Short T-Nut M4 WP-VJS/01A

2 12 Varijig Machine Screw M4 x 6mm Csk Zinc WP-VJS/02

3 6 Varijig Machine Screw M4 x 6mm Csk Black WP-VJS/03
4A 1 Varijig Scale 400mm Metric/Imperial WP-VJS/04A
4B 2 Varijig Scale 150mm Metric/Imperial WP-VJS/04B

5 2 Machine Screw Csk M5 x 20mm Phillips WP-SCW/86

6 1 Varijig End Cap for Extrusion WP-VJS/06
7A 2 Varijig Alloy Extrusion 310mm WP-VJS/07A
7B 2 Varijig Alloy Extrusion 430mm WP-VJS/07B

8 2 Varijig Corner Frame WP-VJS/08

9 -- ­10 2 Varijig Connector Block WP-VJS/10
11 1 Varijig Right Hand Stop WP-VJS/11
12 1 Varijig Left Hand Stop WP-VJS/12
13 2 Varijig Squaring Plate WP-VJS/13
14 1 Varijig Bottom Squaring Butt WP-VJS/14
15 1 Varijig Clamping Plate WP-VJS/15
16 2 Varijig Machine Screw M4 x 10mm Csk Black WP-VJS/16
17 4 Varijig Machine Screw Skt UNC 5/16” x 5/8” WP-VJS/17
18 2 Varijig Set Screw Skt UNC 5/16” x 5/8” WP-VJS/18
19 1 Hex Key 4mm A/F WP-AP/04
20 1 Hex Key 6mm A/F WP-AP/06
21 1 Manual MANU/VJS/TG

-12-

VJS/TG/JIG

2

VJS/TG/JIG - SPARE PARTS DIAGRAM

4B

16

13

1

15

v1.0 08/2007

8

6

11

12

1A

7A

7B

5

14

18

17

-IB-

10

20

VARIJIG

TENON &
GROOVING J IG

19

21

Trend Machinery & Cutting Tools Ltd.

Odhams Trading Estate St Albans Road
Watford WD24 7TR England

Tel: [phone]
[e-mail]

MANU/VJS/TG v2.0

© Copyright Trend 2012. No part of this publication may be reproduced, stored or transmitted in any form without prior permission.

Our policy of continuous improvement means that specifications may change without notice. Trend Machinery and Cutting Tools

cannot be held liable for any material rendered unuseable or any form of consequential loss. E&OE

RECYCLABLE

www.trend-uk.com