Trend TEMP/CTI/A Additional information

MAINTENANCE

Please use only Trend original spare parts and
accessories.

The accessory has been designed to operate
over a long period of time, with the minimum
amount of maintenance. Continual satisfactory
operation depends upon proper tool
care and regular cleaning.

Cleaning

n Regularly clean jig with a soft cloth.
n Do not use a corrosive cleaning solutions.

Lubrication

n Your accessory requires no additional

 lubricationapartfromthe‘O’ringwhich
may require lubrication to fit onto guide
bush.

Storage

n Always return product to its packaging after
use, or hang on a wall hook

ENVIRONMENTAL
PROTECTION

Recycle raw materials instead of
disposing as waste.

Packaging should be sorted for
environmental-friendly recycling. The product
and its accessories at the end of its life should
be sorted for environmental-friendly recycling.

GUARANTEE

All Trend products are guaranteed against any
defects in either workmanship or material, except
products that have been damaged due
to improper use or maintenance.

Trend Machinery & Cutting Tools Ltd.

OdhamsTradingEstateSt AlbansRoad

Watford WD24 7TR England

Tel: [phone]
[e-mail]
www.trend-uk.com

Safety Points

1. Disconnect power tool and attachment from power supply
when not in use, before servicing, when making adjustments
and when changing accessories such as cutters. Ensure
switch is in “off” position. Always ensure cutter has stopped
rotating.

2. Read and understand instructions supplied with power tool,
attachment and cutter.

3. Current Personal Protective Equipment (PPE) for eye, ear
and respiratory protection must be worn. Keep hands, hair
and clothes clear of the cutter.

4. Before each use check cutter is sharp and free from damage.
Do not use if cutter is dull, broken or cracked or if any
damage is noticeable or suspected.

5. The maximum speed (nmax) marked on tool or in instructions
or on packaging shall not be exceeded. Where stated, the
speed range should be adhered to.

6. Insert the shank into the router collet at least all the way to
the marked line indicated on the shank. This ensures at least
3/4 of shank length is held in collet. Ensure clamping surfaces
are clean.

7. Check all fixing and fastening nuts, bolts and screws on
power tool, attachment and cutting tools are correctly
assembled, tight and to correct torque setting before use.

8. Ensure all visors, guards and dust extraction is fitted.

9. The direction of routing must always be opposite to the
cutter’s direction of rotation.

10. Do not switch power tool on with the cutter touching the
workpiece.

11. Trial cuts should be made in waste material before starting
any project.

12. Repair of tools is only allowed according to tool
manufacturers instructions.

13. Do not take deep cuts in one pass, take several shallow
passes to reduce the side load applied to the cutter.

Please see www.trend-uk.com/safety for more safety advice.

Our policy of continuous improvements mean
that specifications may change without notice.
Trend Machinery & Cutting Tools Ltd. cannot be
held liable for any material
rendered unusable, or for any
form of consequential loss.

©CopyrightTrend2014,2016. E&OE.

® All trademarks acknowledged.

RECYCLABLE

CABLE TIDY

INSERT TEMPLATE

Apertures to be routed
in desks or any surface
where cables need to
be hidden.

n60mm & 80mm round and

105mm x 55mm rectangular
holes.

nTemplate can also be used to

cut a 35mm blind hole for
circular kitchen door hinges.

Requires:

n Plunge router.

n

12mm Straight cutter
Ref. 3/73X1/2TC, C200DX1/2TC,
3/8LX1/4TC or C019AX1/4TC.

n 30mm Guide bush Ref. GB30*.

n Suitable clamping devices.

Size: 325mm x 290mm x 8mm

* A Unibase may be required for
certain makes and model of router.

C/TEMP/CTI/A v3.0

FOR GUIDING
THE ROUTER

Feed
direction

For
35mm
kitchen
door
hinge

For
80mm
insert

For 105x
55mm
rectangle
insert

For
60mm
insert

Feed
direction

CABLE TIDY INSERT
REF. TEMP/CTI/A

Thank you for purchasing this Trend product
which should give lasting performance if used
in accordance with these instructions.

The following symbols are used throughout
these instructions.

Denotes risk of personal injury,
loss of life or damage to the tool
in case of non-observance of the
instructions.

Refer to the instruction manual of
your power tool.

This unit must not be put into service until it
has been established that the power tool to
be connected to this unit is in compliance with
2006/42/EC (identified by the CE marking on
the power tool).

INTENDED USE

This accessory is intended to be used with
a plunge router with suitable straight router
cutter and guide bush fitted to rout apertures
for 60mm and 80mm round cable tidy inserts,
a 105mm rectangular cable tidy insert and a
35mm blind hole for a circular hinge.

SAFETY

Please read and understand these safety
instructions and the safety points at end of
this instruction as well as the power tool
instructions before use.

PLEASE KEEP THESE INSTRUCTIONS IN
A SAFE PLACE.

The attention of UK users is drawn to The
Provision and Use of Work Equipment
Regulations 1998, and any subsequent
amendments.

UsersshouldalsoreadtheHSE/HSCSafe

Use of Woodworking Machinery Approved
Code of practice and Guidance Document
and any amendments.

Users must be competent in using
woodworking equipment before using our
products.

Consider working environment before
using tools.

Ensure working position is comfortable and
component is clamped securely.

Please keep children and visitors away from
tools and work area. All power tools will have
a residual risk, so must be operated with
caution.

OnlyusetoolingthatmeetsEN847-1/2safety

standard and any amendments.

ITEMS REQUIRED

n Plunge router.
n 12mm diameter TCT router cutter.
n 30mm guide bush.
nSuitable clampingdevices.
n Hand tools.

DESCRIPTION OF PARTS

For
35mm
kitchen
door
hinge

For
80mm
insert

Keep proper footing and balance at
all times.

As templates are made of clear plastic
please be aware of possible glare.

The material being cut, along with the
template/jig will need to be supported and
clamped securely. Ensure that the router
base will not foul the clamps.

For 105x
55mm
rectangle
insert

For
60mm
insert

OPERATION

The template will need to be used on a
component that is a suitable size to ensure
template is supported properly and that
component and template can be clamped
securely.

Setting up the Router

n Ensure router is isolated from power

before making any adjustments.

Fit the 30mm guide bush to the router.

n
n Fit the 12mm diameter cutter into router.

n Setdepthstopofroutertorequireddepth

of cut maximum 8mm per pass.

Routing Aperture for
Cable Tidy Inserts

Position template onto the required position
on the workpiece. Using two clamps securely
clamp the template to the workpiece ensuring
the clamps will not foul the path of the cutter.

Place guide bush into required hole in
template, switch on router and plunge cut into
the workpiece, rout in a clockwise direction.
Repeat operation at progressive depths until
hole is cut. Due to build up of wood waste it is
advisable to vacuum up the wood waste in the
routed trench every so often.

Oncetheholeisrouted,unclampthetemplate
andttheplasticinsert.

Feed
direction

Routing Recess for 35mm
Circle Hinge

The template can also be used to rout 35mm
diameter blind holes for 35mm circular
concealed hinges for kitchen and cabinet

doors.SetupprocedureisthesameInsets,

except the final depth of cut is 11mm, and the
centre of the blind hole must be routed flat.

After use, store accessory carefully.

ACCESSORIES

Please use only Trend original accessories.

Accessory Cable Tidy Insert Chart

Insert Colour

light grey

72

brown
black

3

22

60Ø

92

light grey
brown

3

black

22

80Ø

118

68

grey
black

105

55

Ref. 3/73, C200D, 3/8L or C019A

Ref. GB30

Ref.UNIBASE

For certain makes of router,
a sub-base will be required to
allow the guide bush to
be fitted.

SPARE PARTS

Please use only Trend original spare parts and
accessories.

Ref.

(3 pack)

CTI/60/PK1
CTI/60/PK2
CTI/60/PK3

CTI/80/PK1
CTI/80/PK2
CTI/80/PK3

CTI/105/PK1
CTI/105/PK3

Application

12mm

30mm