Thermistor Room Termperature Sensors
Important: Retain these instructions
UNPACKING
INSTALLATION
Dimensions
1
85 mm (3.35”)
Installation Instructions
TB/TS
TB/TS Installation
Instructions TG200604
85 mm (3.35”)
Requirements
2
a
d
TB/TS Thermistor Room Temperature Sensors Installation Instructions TG200604 Issue 1/E 14/02/07
e
b
f
26 mm (1.02”)
> 50 cm (20”)
1.5 m
(5 ft)
g
c
1
TB/TS Installation Instructions
INSTALLATION (continued)
Requirements (continued)
2
h
k
3
a
i
Remove backplate
wall box
b
60 mm (2.36”)
4
BESA box
wall
-10 °C
j
(14 °F)
0 °C
(32 °F)
0 %RH
H O
2
l
35 mm (1.38”)
+50 °C
(122 °F)
+40 °C measurement
(104 °F)
90 %RH
Mount
backplate
35 mm (1.38”)
2
FR
ABS
Remove cutout(s)
5
as required
35 mm (1.38”)
Route cables
6
TB/TS Thermistor Room Temperature Sensors Installation Instructions TG200604 Issue 1/E 14/02/07
35 mm (1.38”)
Installation Instructions TB/TS
1
3
2
INSTALLATION (continued)
Wire to controller
7
Terminal size 0.5 to 2.5 mm
(14 to 20 AWG)
2
Note that screened cable is not required for sensor
if IQL
wiring to IQLs. If screened cable is used, the
screen must be terminated at the controller to its
supply cable earth.
LQISNOITPO
,+31,21,+11,01LQI
ST/BT
71,61,+51,41
I Q L 1 0 / 2 4 V A C
910
C O M
TB/TS
I Q L 1 2 , 1 4
1
C O M
2 1 2 2
TB/TS
I Q L 1 0 / 2 3 0
1
C O M
1 5 1 6
TB/TS
I Q L 1 3 + , 1 5 + , 1 6
1
2 3 4
C O M
C O M
2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8
TB/TS
I Q L 1 1 + / 2 4 V A C
9 1 011 1 1 2
C O M
C
TB/TS
5
if IQ
SENSOR
TB/TS
polarity independent
1 3
C
1
2 3 4
C O M
2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8
TB/TS
0 V
Temperature
I Q L 1 1 + / 2 3 0
1
2 3
C O M
1 5 1 6 1 7 1 8 1 9
TB/TS
I Q L 1 7
A I
1 0 V
0 V
C
COM (0V)
IN
C
5
IQ
analogue input
linked for thermistor (T)
Assemble unit
8
‘click’
TB/TS Thermistor Room Temperature Sensors Installation Instructions TG200604 Issue 1/E 14/02/07
3
TB/TS Installation Instructions
INSTALLATION (continued)
Set up IQ Sensor types
9
It is recommended to use SET (software tool) for the setting of sensor type modules.
For all IQ2 series controllers with firmware version 2.1 or greater, or IQ3 series controllers,
select the appropriate SET Unique Sensor Reference from the following:
Thermistor: Thermistor TBTS (°C)
If not using SET, use the following tables for all IQ2 series controllers of firmware version
2.1 or greater or IQ3 controllers; for all other IQ controllers see Sensor Scaling Reference
Card TB100521A.
tYpe Sensor digI/P Driver Function loGic Loop scHedule seQnc Analog
digBit Knob sWitch Time Zone Oss User addRess intcoN calarM reView Plot
calEndar
Thermistor TBTS F (°F)
= ?
C°F°
epyttupnI
tnenopxE
05221
reppU
rewoL
5-32
stnioP
146.205221
74.304401
64.40368
366.60105
866.7023
201.85-32
)stlovrotsimreht(1
3
6
DISPOSAL
WEEE Directive :
At the end of their useful life the
packaging and product should be
disposed of by a suitable recycling
Do not dispose of with normal household waste.
Do not burn.
centre.
10
If IQ
If IQL
Thermistor (0 to +40 °C)
Yn<CR>
TYPE n
:
=?
S=5 (characterise)
Y=, E=, U=, L=, P=,
I1 to I6=, O1 to O6=
X <CR>
Test system
I Q
stinU
Y
E
U
L
P
xxI)C°(xO)F°(xO
1
2
3
4
5
6
Δ T
IQL Strategy Installation
Instructions
Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route
du Bois 37,Switzerland by its Authorized Representative.
Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof
without obligation to notify any person of such revisions or changes.
Trend Control Systems Limited
P.O. Box 34, Horsham, West Sussex, RH12 2YF, UK. Tel:+44 (0)1403 21888 Fax:+44 (0)1403 241608 www.trend-controls.com
Trend Control Systems USA
6670 185th Avenue NE, Redmond, Washington 98052, USA. Tel: (425)897-3900, Fax: (425)869-8445 www.trend-controls.com
4
TB/TS Thermistor Room Temperature Sensors Installation Instructions TG200604 Issue 1/E 14/02/07
Loading...