Trend M/P2P01 User guide

Please read inside before use
POINT2
Product Ref.
M/P2P01
POINT2
85mm to 710mm
MK2
POINT
EQUIDISTANT MEASURING
Mark equally spaced multiple points, for drilling, dowelling, jointing pinning and flat dowelling.
n Centre point finder.
increased accuracy.
n 710mm (28”) maximum extension,
minimum width 85mm.
2-point locking mechanism with 7
equidistant marking positions.
For left and right hand use.
Ideal for woodworking, arts
and crafts, sewing etc.
MK2
POINT
EQUIDISTANT MEASURING
Mark equally spaced multiple points, for drilling, dowelling, jointing pinning and flat dowelling.
n Making layout tasks easier, faster
& more accurate.
Equidistant measuring gauge with
centre point finder.
2-point locking mechanism with 7
equidistant marking positions from 85mm to 710mm.
For left and right hand use.
Ideal for woodworking, arts and
crafts, sewing etc.
Simply expand the point to point mechanism, find the ideal spacings and lock the 7-point marking positions, then transfer to component.
Product Ref
M/P2P01
RECYCLABLE
Trend Machinery &
GB
Cutting Tools Ltd.
Tel: 0044(0)1923 249911 technical@trendm.co.uk www.trend-uk.com
USA
Trend Routing Technology Inc.
Tel: 336 292 5051 technical@trend-usa.com www.trend-usa.com
POINT 2 POINT REF. M/P2P01
Thank you for purchasing this Trend product, which should give lasting performance if used in accordance with these instructions.
The following symbols are used throughout these instructions.
Denotes risk of personal injury,
loss of life or damage to the tool in case of non-observance of the instructions.
SAFETY
Please read and understand the following instructions before use.
PLEASE KEEP THESE INSTRUCTIONS IN A SAFE PLACE.
Users must be competent in woodworking equipment before using our products. Consider working environment before using tools. Ensure working position is comfortable and component is clamped securely.
Please keep children away from tools and work area. All tools have a residual risk, so must therefore be handled with caution.
DESCRIPTION OF PARTS
A. Upright cut outs x14 B. Central uprights B1. Uprights x7 C. Struts x5 D. Tensioning pinch
bolts x2 E. Short Struts x2
A
D
INTENDED USE
Multi Point Layout
The Point 2 Point has been designed to offer an instant visual guide during layout tasks, including working out the positions of screws, dowels, pins or alternatively shirt buttons, curtain pleats etc.
Min.width: 85mm Max.width: 710mm
Centre Finder
Find the center point of a board quickly, indicated
by the Point 2 Point’s central upright.
Strip Calculator
The Point 2 Point can also indicate the maximum number of strips that can be cut from a board.
OPERATION
It’s recommended that where possible the Point 2 Point is used on a flat surface.
The Point 2 Point is designed for both left & right handed users. To correctly orientate the Point 2 Point, ensure the right angle cut out on the uprights face the hand you write with.
Before use ensure the pinch bolts are loose.
Please note, pinch bolts are for tensioning and not to fully tighten down the uprights.
Centre Line
B
B1
C
Equidistant Layout
n Mark the two outer positions of the area to be sub-divided.
n Expand the Point 2 Point mechanism past the outer markings.
n Gently compress the mechanism down to the required size.
n Carefully tighten both tensioning pinch
bolts, ensuring that the ‘’setting’’ is not
disturbed. Please note, the pinch bolts are for tensioning and not to fully tighten down the uprights.
n Mark the divisions indicated by the upright cuts outs.
Large Workpiece Layouts
When marking out positions on a larger panel. Divide the panel into equal sections of less than 710mm (28”), then sub-divide the sub section with the Point 2 Point.
Although the accuracy of the MK2 has been improved, it is not suitable for marking out dovetail, finger or other small, high tolerance joints. This is due to the float within the mechanism.
MAINTENANCE
Please use only Trend original spare parts and accessories.
This accessory has been designed to operate over a long period of time with minimum amount of maintenance. Continual satisfactory operation depends upon proper tool care and regular cleaning.
Cleaning
n Regularly clean with a soft cloth.
Do not disassemble product.
n
Lubrication
n Requires no additional lubrication.
Storage
When the Point 2 Point is set to the chosen size, carefully tighten the tensioning pinch bolts. This allows the Point 2 Point setting to be transferred down the board, or to another workpiece.
Centre Finder
n Expand then contract the Point 2 Point
mechanism so that the outer marking points are aligned with the outside edge of the area you wish to divide.
The centre of the board is indicated by the
n
central upright “cut out’’.
Strip Calculator
n Expand the Point 2 Point across the full
width of the board. The mechanism now gives a visual indication of the number and width of strips that can be cut.
After use, loosen pinch bolts, compress the mechanism and lock pinch bolts. Store
E
carefully.
n Store product safely in a cupboard.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing as waste.
Packaging should be sorted for environmental-friendly recycling. The product and its accessories at the end of its life should be sorted for environmental-friendly recycling.
GUARANTEE
All Trend products are guaranteed against any defects in either workmanship or material, except products that have been damaged due to improper use or maintenance.
© Copyright Trend 2014. No part of this publication may be reproduced, stored or transmitted in any form without
prior permission. Our policy of continuous improvement
means that specifications may change without notice.
Trend Machinery and Cutting Tools cannot be held
liable for any material rendered unusable or any form of
consequential loss. E&OE
® All trademarks acknowledged.
INST/MP2P01 v1.1
Loading...