TREND IQ3xact User Manual

Important: Retain these instructions

!

CONTENTS

Installation Instructions

IQ3xact

Web Enabled Controller

1 Unpacking.......................................................................... 1

2 Storing ................................................................................ 1

3 Installation - Mounting ....................................................... 1

1 Unpacking

2 Storing

-10 °C (14 °F)

+50 °C (122 °C)

H2O

0

90 %RH

4 Installation - Configuration ................................................ 5

5 Replacing the Battery ..................................................... 11

6 Disposal ........................................................................... 12

IQ3xact Installation Instructions TG200766

It is recommended that the installation should comply with the HSE Memorandum of Guidance on Electricity at Work Regulations 1989. For USA install equipment in accordance with National Electric Code

DANGER high voltage. No serviceable parts inside. Other than removing terminal cover, auxiliary board cover, and lifting I/O bus flap, DO NOT OPEN UNIT.

3 Installation - Mounting

1

terminal cover

150 mm (5.9")

Dimensions

4 5 6

1 2 3

1

2

+ 0

130 mm (5.12")

100-240 V

auxiliary board cover

access for connections

263 mm (10.35")

16 17 18

13 14 15

10 11 12

7 8 9

3

5

6

4

+ 0

OK RX

24 V

0 V

access for connections

WARNING. If the unit is used in a manner other than that specified in these instructions, the protection provided by the unit may be impaired.

2

Requirements

a

46 mm (1.81")

42 mm (1.65")

50 mm

(1.97")

16

13

11

12

14A

P 0

P 0 31 32 33

P

P 0

40 41 42

43 44 451546 47 48

P 0

34 35 36

37 38 39

b

access for cover and auxiliary board option

H2O

Protection IP20, NEMA1

1 2 3

1

+ 0

100-240 V

1 2 3

1

+ 0

100-240 V

0 °C (32 °F)

0 %RH

4 5 6

16 17 18

13 14 15

10 11 12

7 8 9

3

5

6

2

4

+ 0

A

16

15

13

11

12

14A

P 0

OK RX

34 35 36

31 32 33

37 38 39

43 44 45

46 47 48

40 41 42

P

24 V

0 V

4 5 6

16 17 18

13 14 15

10 11 12

7 8 9

3

5

6

2

4

+ 0

A

16

13

11

12

14A

P 0

OK RX

34 35 36

31 32 33

37 38 39

43 44 451546 47 48

40 41 42

P

24 V

0 V

+45 °C (113 °F)

90 %RH

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

1

IQ3xact Installation Instructions

0

3 Installation - Mounting (continued)

2

Requirements (Continued)

c

4 5 6

16 17 18

13 14 15

19 20 21

1 2 3

22 23 24

25 26 27

10 11 12

7 8 9

28 29 30

3

5

6

8

9

10

1

2

4

7

+ 0

+ 0 + 0+ 0

+ 0

A

100-240 V

16

13

11

12

14A

P 0

OK RX

34 35 36

37 38 39

31 32 33

43 44 451546 47 48

40 41 42

P

24 V

24 V 0 V

4 5 6

16 17 18

13 14 15

1 2 3

10 11 12

7 8 9

3

5

6

1

2

4

+ 0

100-240 V

16

15

13

11

12

14A

P 0

OK RX

34 35 36

31 32 33

37 38 39

43 44 45

46 47 48

40 41 42

P

24 V

0 V

IQ3XACT/12/USA/UL/../24 is UL rated as ‘UL916 listed open energy management equipment’.

Mounting

3

a

d

4 5 6

16 17 18

13 14 15

1 2 3

10 11 12

7 8 9

3

5

6

1

2

4

+ 0

100-240 V

OK RX

24 V

16

13

11

12

14A

P 0

34 35 36

31 32 33

37 38 39

43 44 451546 47 48

40 41 42

P

24 V

0 V

e

4 5 6

16 17 18

13 14 15

1 2 3

10 11 12

7 8 9

3

5

6

1

2

4

+ 0

100-240 V

+ 0

1 2 3

1

4 5 6

+ 0

2

+ 0

7 8 9

3

10 11 12

+ 0

4

13 14 15

+ 0

RX OK

5

16 17 18

+ 0

6

24 V

0 V

24 V

P

31 32 33

P 0

11

34 35 36

P 0

12

37 38 39

P 0

13

40 41 42

P 0

14A

43 44 45

P 0

15

46 47 48

P 0

16

13

11

12

14A

P 0

OK RX

34 35 36

31 32 33

37 38 39

43 44 451546 47 48

40 41 42

P

24 V

0 V

16

P 0

46 47 48

15

P 0

43 44 45

14A

P 0

40 41 42

13

P 0

37 38 39

12

P 0

34 35 36

11

P 0

31 32 33

P

24 V

0 V

24 V

6

+ 0

16 17 18

5

RX OK

+ 0

13 14 15

4

+ 0

10 11 12

3

7 8 9

+ 0

2

+ 0

4 5 6

1

+ 0

1 2 3

100-240 V

P 0

16

40 41 42 43 44 451546 47 48 P 0

P 0

14A

13

0 V

24 V

P

37 38 39

31 32 33

34 35 36

OK RX

P 0

12

11

100-240 V

+ 0

2

4

1

3

5

6

7 8 9

10 11 12

1 2 3

13 14 15

4 5 6

16 17 18

DIN rail end stop

4 5 6

1 2 3

1

2

+ 0

b

c

+ 0

16 17 18

13 14 15

10 11 12

7 8 9

3

5

6

4

+ 0

4

/100-240 100 to 240 Vac ±10% 50/60 Hz at 28 VA max

(A 240 Vac, 1 A, switch or circuit breaker must be included in the supply

Connect Power

to the unit and be in close proximity to it, and must be clearly marked as the disconnecting device for the unit.)

/24 24 to 60 Vdc (36 Vdc maximum for /UL

versions), 24 Vac 50/60 Hz, at 40 VA max

ensure DIN rail is earthed (grounded)

4 5 6

1 2 3

1

2

+ 0

100-240 V

/100-240

100-240 V

16 17 18

13 14 15

10 11 12

7 8 9

3

5

6

4

+ 0

16

13

11

12

14A

P 0

34 35 36

37 38 39

24-60 V 24 V

P 0

43 44 451546 47 48

40 41 42

OK RX

31 32 33

P

24 V

0 V

USA/UL/24

V

Terminal size 0.5 to 2.5 mm

(36 Vdc maximum for /UL)

24 Vac

E

24 to 36 Vdc

2

(14 to 20 AWG)

O

I

EN61010:2001

INSTALLATION CATEGORY III

(fixed installations)

5

Connect to Ethernet

If required

4 5 6

1 2 3

+ 0

100-240 V

10 11 12

7 8 9

3

1

2

+ 0

Standard Ethernet

100-240 V

16 17 18

13 14 15

5

6

4

+ 0

11

P 0

OK RX

31 32 33

P

24 V

0 V

11

P 0

OK RX

34 35 36

31 32 33

P

24 V

0 V

15

13

12

14A

P 0

34 35 36

P 0

37 38 39

43 44 45

46 47 48

40 41 42

RJ45

16

13

12

14A

P 0

37 38 39

43 44 451546 47 48

40 41 42

16

cable

100 m (max)

Cat 5e twisted pair

Ethernet hub or switch e.g EDS205 5 port unmanaged switch (available from IQ system supplier)

Note that a single device may be connected directly to the IQ3 from Ethernet using the standard Ethernet cable plus an XCITE/XA crossover adaptor, see ‘Connect IPTool’ (section 4, step 13)

DO NOT APPLY

POWER

2

This apparatus must be earthed (grounded) (through power connector)

WARNING:

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

Trend Ethernet Products Engineering Guide TE200369

Installation Instructions IQ3xact

V

4 5 6

2

7 8 9

3

10 11 12

4

13 14 15

5

16 17 18

6

+ 0

1 2 3

1

+ 0

0 V

24 V

34 35 36

12

37 38 39

13

40 41 42

14A

31 32 33

P

11

43 44 45

15

46 47 48

16

100-240 V

OK RX

P 0

3 Installation - Mounting (continued)

6

Connect Inputs (channels 1 to 6)

N

EN61010:2001 MEASUREMENT CATEGORY 1. Separate from 230 Vac input power supply by double or reinforced insulation

TP/1/1/22/HF/200 (Belden 8761) cable recommended for all inputs. Cable size 0.5 to 2.5 mm2 (14 to 20 AWG) - Cu only

Voltage input

(0 to 10V)

1 2 3

1

+ 0

0 (0 V)

N (in) + (+24V)

4 5 6

2

+ 0

N

7 8 9

+ 0

linking

10 11 12

3

4

+ 0

13 14 15

5

+ 0

4 5 6

1 2 3

1

+ 0

2

16 17 18

+ 0

10 11 12

7 8 9

3

+ 0

6

16 17 18

13 14 15

5

6

4

+ 0

V

Current input (loop powered)

®

(0 to 20 mA)

SIG

1

0 (0 V) N (in)

linking

N

100-240 V

Thermistor input

+ (+24V)

(20 to 36 V)

I

0V

Current input (external powered)

0V

SIG

®1 (0 to 20 mA)

0 (0 V) N (in) + (+24V)

linking

N

Digital input

I

Note that setting input links is described in Installation Instructions - section 4, step 6

11

P 0

OK RX

34 35 36

31 32 33

P

24 V

0 V

5 V bridge supply

0 (0 V) N (in) + (+24V)

12

5 V supply

16

15

13

14A

P 0

37 38 39

43 44 45

46 47 48

40 41 42

linking

N

T

linking

N

D

Segregate Screen Earth (Ground)

7

separate earth (ground) connection

8

1 2 3

+ 0

100-240 V

If external supply is used to supply P input terminal, note whether P bus is 24 Vac or 24 Vdc and only connect appropriate output

devices to P output terminals

Additional Relay Modules

IQ3

if required to segregate screen earth (ground) from controller input power supply earth (ground)

Note that screen earth (ground) link must be cut (see section 4, step 7)

4 5 6

1 2 3

+ 0

Connect Outputs (channels 11 to 16)

4 5 6

1

2

+ 0

16 17 18

13 14 15

10 11 12

7 8 9

3

5

6

4

+ 0

2

1

+ 0

N

EN61010:2001 MEASUREMENT CATEGORY 1. Separate from 230 Vac input power supply by double or reinforced insulation

TP/1/1/22/HF/200 (Belden 8761) cable recommended for voltage outputs

If screened cable is used, terminate screen to earth (ground) at one end

11

P 0

34 35 36

16

15

13

11

12

14A

P 0

OK RX

31 32 33

P

24 V

0 V

P 0

34 35 36

37 38 39

43 44 45

46 47 48

40 41 42

31 32 33

Cable size 0.5 to 2.5 mm2 (14 to 20 AWG) - Cu only

13

12

P 0

37 38 39

14

P 0 40 41 42

P 0 43 44 451546 47 48

WARNING

N

(out) N

16

P 0

0

(0 to 10 Vdc, <=20 mA)

P

(+24 V)

optional

I<=20 mA

(0 V)

If P terminal used, P input terminal must be

Relay

N

SRMV =

2SRM =

2RM =

3RM =

6RM =

Module

nRM

x 1

x 2

x 3

x 6

e.g.

(R/L, H/L)

(HCM/TRM)

connected as in step 9 below

IQ3

SRMV

0

P

SRMAC

Analogue outputs are not suitable for ac relays

LOAD

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

3

IQ3xact Installation Instructions

A

31 32 33

P

11

P 0

3 Installation - Mounting (continued)

9

either use IQ3 24 Vdc auxiliary supply

if P terminal used (see step 8 above)

Check IQ3 24 Vdc combined and auxiliary output current availability: IQ3 Configuration Manual TE200768

A

11

A

P 0

31 32 33

P

24 V

0 V

Fit external link

Connect Output Power (P)

terminal size 0.5 to 2.5 mm2 (14 to 20 AWG)

4 5 6

1 2 3

1

+ 0

16 17 18

13 14 15

10 11 12

7 8 9

3

5

2

6

4

+ 0

EN61010:2001 MEASUREMENT

CATEGORY 1

Separate from 230 Vac input power

100-240 V

13

11

12

14A

P 0

OK RX

P 0

34 35 36

31 32 33

37 38 39

40 41 42

P

24 V

0 V

supply by double or reinforced

16

15

P 0

43 44 45

46 47 48

insulation

or use 24 Vdc or 24 Vac external supply

Connect external supply (no external link)

31 32 33

24 V

0V

External PSU must be dedicated

WARNING

to I/O channel use, and comply with relevant EMC and safety standards

PSU

External PSU

WARNING If external supply is used, note whether P bus is 24 Vac or 24 Vdc and only connect appropriate output devices to P output terminals

10

Connect Auxiliary Supply (24 V )

Check IQ3 24 Vdc combined and auxiliary output current availability: IQ3 Data Sheet TA200505

A

P

24 V

0 V

11

Install Auxiliary Board

for IQ3../.../LAN/...

for IQ3../.../XNC/..., including IQ3../.../LAN/XNC/..., IQ3../.../SER/XNC/...

if required

4 5 6

1 2 3

1

+ 0

16 17 18

13 14 15

10 11 12

7 8 9

3

5

2

6

4

+ 0

terminal size 0.5 to 2.5 mm2 (14 to 20 AWG)

100-240 V

13

11

12

P 0

OK RX

34 35 36

31 32 33

37 38 39

P

24 V

0 V

EN61010:2001 MEASUREMENT CATEGORY 1

16

15

14A

P 0

43 44 45

46 47 48

40 41 42

Separate from 230 Vac input power supply by double or reinforced insulation

Note that the 24 Vdc supply is normally about 22 V

IQ3

0 V

A

24 V

and drops to about 20.7 V at full load.

Imax = 150 mA(including current to P bus,

- see step 9 above)

if fitted (for battery board, XCITE/BBC, see section 4, step 19)

IQ3../.../LAN/... Installation Instructions TG200916 section 1

IQ3../.../XNC/... Installation Instructions TG200911 section 1

4

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

Installation Instructions IQ3xact

4 Installation - Configuration

Switch Off

1

O

I

Open Panel

3

WARNING: Opening the panel may expose

dangerous voltages.

417-IEC-5036

4 5 6

1 2 3

1

2

+ 0

100-240 V

2

Isolate I/O

4 5 6

16 17 18

1 2 3

+ 0

13 14 15

10 11 12

7 8 9

3

5

1

+ 0

6

2

4

+ 0

O

I

also isolate I/O of any

adjacent I/O modules

100-240 V

OK RX

P

24 V

0 V

16

15

13

11

12

14A

P 0

34 35 36

31 32 33

37 38 39

43 44 45

46 47 48

40 41 42

O

I

WARNING: The connecting leads may be connected to supplies. Isolate before touching.

Disconnect I/O

16 17 18

13 14 15

19 20 21

25 26 27

10 11 12

22 23 24

7 8 9

28 29 30

3

5

6

8

9

10

4

7

+ 0

+ 0 + 0 + 0

+ 0

A

16

13

11

12

14A

P 0

OK RX

34 35 36

31 32 33

37 38 39

43 44 451546 47 48

40 41 42

P

24 V

0 V

4

4 5 6

1 2 3

1

2

+ 0

100-240 V

16 17 18

13 14 15

10 11 12

7 8 9

5

6

3

4

+ 0

16

13

11

12

14A

P 0

OK RX

31 32 33

P

24 V

0 V

P 0

34 35 36

37 38 39

43 44 451546 47 48

40 41 42

Remove Cover

5

4 5 6

a

1 2 3

1

+ 0

100-240 V

b

4 5 6

1 2 3

1

+ 0

100-240 V

16 17 18

13 14 15

10 11 12

7 8 9

5

6

3

2

4

+ 0

13

11

12

14A

P 0

OK RX

P 0

34 35 36

31 32 33

37 38 39

40 41 42

P

24 V

0 V

Cut Screen Earth (Ground) Link

16 17 18

13 14 15

10 11 12

7 8 9

5

6

3

2

4

+ 0

16

13

11

12

14A

P 0

OK RX

P

24 V

0 V

P 0

34 35 36

31 32 33

37 38 39

43 44 451546 47 48

40 41 42

c

16

P 0

43 44 451546 47 48

100-240 V

13

11

12

14A

P 0

OK RX

P 0

34 35 36

31 32 33

37 38 39

43 44 451546 47 48

40 41 42

P

24 V

0 V

7

if screen earth (ground) segregated from controller input supply earth (ground - see section 3, step 7)

Select Input Channel Types

6

100-240 V

16

D (digital)

P 0

I (current)

(thermistor) T (voltage) V

11

12

P 0

OK RX

34 35 36

31 32 33

P

24 V

0 V

either loop powered (IL), or external powered (IX)

Replace Cover

16

13

14A

P 0

37 38 39

43 44 451546 47 48

40 41 42

8

4 5 6

1 2 3

7 8 9

1

2

+ 0

16 17 18

13 14 15

10 11 12

5

3

6

4

+ 0

100-240 V

11

P 0

OK RX

34 35 36

31 32 33

P

24 V

0 V

16

13

12

14A

P 0

37 38 39

43 44 451546 47 48

40 41 42

screen earth (ground) link

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

100-240 V

11

12

P 0

OK RX

34 35 36

31 32 33

P

24 V

0 V

16

13

14A

P 0

37 38 39

43 44 451546 47 48

40 41 42

5

IQ3xact Installation Instructions

CR 2032

4 Installation - Configuration (continued)

Fit Battery Option

9

if required (to support clock for several years e.g. for Timemaster)

If /LAN/ or /SER/ option fitted see separate installation instructions; for IQ3xcite/../LAN/... see IQ3xcite/../LAN/... installation instructions TG200916 for IQ3xcite/../LAN/XNC/... or IQ3/../SER/XNC/.. see IQ3xcite/../XNC/... installation instructions TG200911

a

remove auxiliary board cover

c

apply board to plate

XCITE/BBC battery option board order separately

replace auxiliary board cover

f

d

press board home

b

apply plate

plate supplied with XCITE/BBC

e

insert battery

battery supplied with XCITE/BBC

Switch On

10

CR 2032

O

I

Check Controller

11

a (watchdog)

(red)

b (power)

(green)

4 5 6

1 2 3

1

2

+ 0

100-240 V

Connect IPTool

13

either use Ethernet connection

The IP addressing may be set up automatically or manually as explained in step 17 below. To discover the IP addressing, or to change it using IPTool:

Note that in order to use IPTool for this, the host PC must have its own IP addressing set up correctly.

13 14 15

10 11 12

7 8 9

3

5

4

+ 0

OK RX

Check Ethernet

4 5 6

1 2 3

1

+ 0

100-240 V

10 11 12

7 8 9

3

2

4

+ 0

16 17 18

13 14 15

5

6

+ 0

16

15

13

11

12

14A

P 0

OK RX

31 32 33

P

24 V

0 V

P 0

34 35 36

P 0

37 38 39

43 44 45

46 47 48

40 41 42

IQ Faulty (software or strategy)

power supply fail

12

return to supplier

16 17 18

6

+ 0

a OK (green)

16

15

13

11

12

14A

P 0

34 35 36

31 32 33

37 38 39

43 44 45

46 47 48

40 41 42

P

24 V

0 V

Check Ethernet

b RX (yellow)

IPTool (and SET v6.2)

standard Ethernet connection see section 3 step 5

Router

IQ3

6

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

Installation Instructions IQ3xact

4 Installation - Configuration (continued)

Connect IPTool (continued)

or local PC (Ethernet) connection can be either to adjacent Ethernet hub using standard cable only, or directly to IQ3

13

using standard cable and crossover adaptor, XCITE/XA.

IPTool (and SET v6.2)

100-240 V

OK RX

RJ45

standard Ethernet cable - see section 3 step 5

XCITE/XA crossover adaptor order separately (XCITE/XA/5 pack of 5)

SET Manual TE200147 IPTool Manual TE200638 IQ3 Reset Applet Manual TG200767

Note that if communications fail completely the IQ3 can be reset using the SET Reset Applet

DHCP Server

14

If the IP address settings (IP address, subnet mask, default router, WINS and DNS servers’ addresses) are to be supplied by a DHCP server, ensure one is installed

Note that on a mutiple segment system a single DHCP server may be used providing it has connections to each segment i.e. mutiple connections

The DHCP server must be capable of downloading either or both (as appropriate - see steps 15 and 16) the WINS server address and the DNS server address.

on the Ethernet segment to which the IQ3 is connected.

Configure Addressing Details with IPTool

17

WINS Server

15

If host names are being used for IP addressing across a router, then a WINS server must be installed on the system.

DNS Server

16

If email alarms are being sent, and the email server address is identified by internet domain name, then a DNS server must be installed on the system.

IQ3 Configuration Manual TE200768 IPTool Manual TE200638

The IQ3’s IP addressing information can be set up automatically (Obtain Automatically) or manually (Enter Manually). When set for automatic IP addressing, the IQ3 will default to link/local mode where it autonegotiates its IP address with other devices on its Ethernet segment, but if a DHCP server is operating on its segment, the server will set up the IP addressing. Alternatively the settings can be specified manually. Certain issues exist when using automatic IP addressing and IQ3/BAC BACnet

protocol (see IQ3 Configuration manual Pt. 1 section 3.7.4)

edoMgnisserddAPIybputesgnisserddaPI

yllacitamotuAniatbO PCHD yravyamsserddaPI

yllaunaMretnE launa

METSYS

)tnemges

)metsys

S

RETEMARAP

eludoMkrowteN

sserddAPI revresPCHDybteSsecivedrehtohtiwdetaitogenotuA

ksaMt

enbuS revresPCHDybteS0.552.552.552sesUlooTPIgnisudeificepsebtsuM

1retuoR revresPCHDybteSA/NlooTPIgnisudeific

emaNtsoH ebnaC.*desueulavtluaf

troPPDU .looTPIgnisudeificepsebnaC.desueulavtluafeD

edomgnisserddaotuA .tluafedehtsisihT.seYotteS.tluafedehtsisihT.seYotteSlooTPIgnisu

revreSSNIW revresPCHDybteSA/Nfi(looTPIgnisudeificepsebnaC

lacol/kniL

M dexifsserddaPI

lacol

no(deriuqeRrevreSPCHD

seYlacolnodellatsniebtontsuM

no(deriuqeRrevreSSNIW

apskrowtenfIoNssorcanoitcennocfideriuqerylnO

eD

PCHD)tluafeD(lacoL/kniL

retuorsn

.looTPIgnisudeificeps

Note that it is recommended that link/local only be used as normal operation on a single segment system.

The addressing details can be viewed or configured using IPTool. The table below describes the options that must be set up for each addressing method.

citamotuAlaunaM

tnemges

.tenbusemasno

dohteMgnisserddA

lamronrofesutonoD

retuorssorcanoitarepo

oN

dnaecivedsihtneewtebsretuor

.seman

oNotteS

epsebtsuM

)deriuqer

.looTPIgnisudeificeps

ebnaC.*desueulavtluafeD

tsohgnisuedamebotsisrehto

.looTPIgnisudeificepsebtsuM

P

IdexifaesuotelbissopsitI

metsysPCHDanosserdda

egnarehtedistuositignidivorp

revresPCHDehtybdetacolla

eulavtluafedtubyrassecentoN

.*tnemg

eslacolnoskrowsyawla

.looTPIgnisudeificepsebnaC

krowt

sretuoRssorcA

eludomsserddA

sserddA looTPIgnisutesebtsumesle,s

rebmunnaL looTPIgnisutesebtsuM

reifitnedI .looTPIgnisudeificepsebnaC.desueulavtluaf

enretnI-)s(ecivedetomeR

eludomCNClautriV

rebmuntrop/sserddA .looTPIgnisu,deriuqerCNCvfirebmuntropdnasserddaCNCteS

ksamtenbusdnaemantsohputeS

A/N,sserddaPIroemantsohputeS

.looTPIgnisusecivedetomerfo

ehctiwsybtesNAL/3QIfI

eD

.looTPIgnisu

secivedetomerfoksamtenbusdna

Step 17 continued

*The default host name will always work unless it has been disabled by setting Default Hostname parameter in Network module to Disabled.

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

7

IQ3xact Installation Instructions

4 Installation - Configuration (continued)

17

1. If IP Addressing Mode set to Obtain Automatically and DHCP operating correctly, the DHCP server will set up IP Address, Subnet Mask,

2. If IP Addressing Mode set to Obtain Automatically and DHCP not operating or missing, the IQ3 will auto negotiate its IP Address (link/local

3. Default host name will continue to operate even when a configured host name is set up unless Default Hostname is set to Disable (using

4. It is possible to use host names in manual IP addressing mode, but the WINS Server(s) must be set up for them to operate across a router.

5. It is possible to use fixed IP addresses in a DHCP regime by setting up the DHCP server appropriately and setting IP Addressing Mode

6. The following IP addresses should not be used:

Further addresses may not be suitable for a particular system; check with the company’s IT department.

7. An invalid subnet mask (e.g. 0.0.0.0) should not be used; check with the company’s IT department for valid masks.

8. Virtual CNC inoperative until its address set up by IPTool or SET. If opened in IPTool default address (101), and port (10101) appear.

9. A change to address parameters (IP, Subnet, UDP, Router1, Lan, outstation, vCNC) causes a general reset.

10. Set up at least 2 remote devices’ IP addresses or hostnames, and subnet mask, from each subnet; as many as possible for each subnet

11. Only the internetwork can span a router, not a Lan.

12.Trend Ethernet devices (i.e. IQ3, EINC, 3xtend/EINC L) on the same segment must be on the same subnet

13. EINC, 3xtend/EINC L, and IQ3 (unless IQ3/Lan) cannot be on same Lan.

14. For IQ3/LAN, Lan number must be same as that of any INC type device or ANC (TMN) type device on its own Lan

The table below gives details of default values and when to change parameters from default

retemaraPgnitteStluafeDnoitcnuF retemarapegnahcotyrassecennoitidnoCetoN

omsserddA

CNClautriV

sserddAPI

ksaMtenbuS

troPPDU53556ot021675

1retuoR

emantsoHem

eludoMkrowteN

PI

sserddA

gni

edoM

SNIW

ot(1srevreS

)02

srevreSSND

)02ot(1

etomeR

1PIseciveD

02ot(

)

etomeR

seciveD

ot(1tenbuS

)02

sserddA911ot11,9ot4,1sserddaedon02naLno3QIfosserddaedon

elud

rebmunnaL911ot11,9ot4,1rebmunnaL02krowtenretnino3QIforebmunnaLputesebTSUM

reifitnedI

sserddA911ot11,9ot4,1sserddaedon

P76723ot1troptenrehtE

.oNtro

sserddaPI

552.552.552ot0.0.0.0

ksaM

sserddaPI

antsohretcarahc51

yllaunam

sserddaPI

emantsohro

ksaM

iremunahpla03

sretcarahc*?;{(\/

TSUM .noitacinummoctenrehtErofputeseb

ton-sretcarahcc

CAM

y

552.

3.1.1.821;sserddaPItenrehtE

0.0.552.552

.552.552

552.552

fonoitcnuF

sserdda

niatbO

0.0.0.0

knalb

.552

knalb3QIrofreifitnedI

delbasid

)101(

delbasid )10101(

TSUM .noitacinummoctenrehtErofputeseb

rebmuntenbus

ocretni

x3QIsatenbus

-llacitamotuA

ddaPI

.eman

-552.552

s

esserddaPIfopu

serddaPI

ivedtenrehtE

retuorfoedisrehtoecived

etarenegotsserddaPIotdeilppaksaM

tsysQIybdesutropPDUtenrehtE

me

metsysQIllA;tenrehtEnotnempiuqe ottropemasesutsumsecived tenrehtEnoetacinumm

smralaliamerofdesu;eman

CNClautrivfotroptenrehtE

tis

TSUM noitacinummoctenrehtErofputeseb

emasnoretuortluafedfosserddaPI

HD

etacinummocotdesU.3QIfoemantsoH

sserddaPIgnisufodaetsni3QIhtiw

TSUM niatbO(tluafedtatfeleb

teslaunaMrocitamotuArehtieseificepS

TSUM desugniebemantsohfiputeseb

orca

revresSNIW.revresSNIWfosser

tsohnevignehwsserddaPIsedivorp

TSUM desugniebsmralaliamefiputeseb

revresSND.revresSNDfos

niamodnevignehwsserddaPIsedivorp

metsysQIfoemantsohrosserddaPI

retuorfoedisrehtoec

tenrehtEmetsysQIfoksamtenbuS

slenap

naLnoCNClautrivfosserddaedoNdesuebotsiCNClautrivfI9,8

552.

552.552.552.552ot0.0.0.0

retnEroyllacitamotuAniatbO

552.552.552.552ot0.0.0.0

fiyllacitamotuateS

.yllaunaM

gnisserddA

.yllaunaMretnEottesedoM

.tenbusnoderiuqer)se

.yllaunaMretnE

etairporppatonsiemantsoh

puteslaunam

yllaunam

.yllaunaM

ybdei

ficepssserddarevresliamedna

)tluafed(yllacitamotuAniatbOottes

.yllaunaMretnE

.sserddaPI

putesebTSUM

tsdeen

degnahcebo

.noitpo/NAL/fisehctiwsmorfteS

idnadesuebotsiCNClautrivfIftluafed

Router 1, WINS servers, and DNS Servers automatically; these cannot be changed by IPTool or SET unless IP Addressing Mode set to Enter Manually

mode) and set Subnet Mask to default, but Router 1, WINS servers, DNS servers remain at last settings. Link/local addresses start at

169.254.0.0 at subnet mask 255.255.0.0. It is recommended that link/local only be used as normal IP addressing mode on a single segment system.

SET or webpages, e.g. for security).

to Enter Manually.

• Addresses 127.x.x.x, reserved for loopback.

• Addresses 224.0.0.0 to 239.255.255.255, reserved for multicast.

• Addresses 240.0.0.0 to 247.255.255.255, reserved for development.

• The non masked part of the address cannot be all 1’s or all 0’s e.g. if address is 1.2.x.x and subnet mask is 255.255.0.0 then x.x. cannot be either 255.255 or 0.0.

(Note that this should be changed if other IQ3s on same Lan with vCNCs, else may get duplicate addreses).

recommended. If using manual IP addressing mode choose lowest IP addresses.

2,1

tesedoMgnisserddAPI

teseboT)tluafed(yllacitamotuAniatbOot

9

retnEottesedoMgnisserddAPIfiyllaunam

PIfdnagnitarepoPCHDfiyllacitamotuateS

yllacitamotuAniatbOottesedoM

21

gnisserddAPIfiyllaunamteseboT)tluafed(

desuydaerlatropfitropPDUegnahcyaM

.e.i(skrowtenretnielpitlumfiro,tenrehtEno

9

fiyllacitamotuateS.tenbusnwoedistuo

edoMgnisserddAPIfdnagnitarepoPC

9

eboT)tluafed(yllacitamotuAniatbOottes

ottesedoMgnisserddAPIfiyllaunamtes

3QI

sihtsseccaotemantsohgnisufiputeS

tluafedDNA)gnitareporevresPCHDfi.g.e(

4,3

fiegnahC.gnitarepoPCHDfi)yllacitamotuA

.deriuqergnisserddaPIfo

PCHDfiyllacitamotuateS.retuorss

ottesedoMgnisserddAPIfdnagnitarepo

teseboT)tluafed(yllacitamotuAniatbO

retnEottesedoMgnisserddAPIfi

fiyllacitamotuateS.emanniamodtenretni

2,1

edoMgnisserddAPIfdnagnitarepoPCHD

eboT

ottesedoMgnisserddAPIfiyllaunamtes

tsuM.retuorsnapskrowtenretniQIfiputeS tegratdnagnitarepoPCHDfiemantsoheb

saputesesle,gnisserdda-otuaottesecived

11

.retuorsnapskrowtenretniQIfiputeS

11

41

yalpsidrosrosivrepusrofputessyawlA

9

9,8

Configure Addressing Details with IPTool (continued)

,

,6,5

,2,1 ,9,7

,2,1

5,2,1

4,2,1

,5,4 ,01

,01

,31,9

8

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

Installation Instructions IQ3xact

M A C A d d r

00.10.70.00.UD.BB

S/No:

Q3B____X73010003

IP A dd r

Location

4 Installation - Configuration (continued)

Write on Label

18

4 5 6

1 2 3

1

2

+ 0

M A C Ad d r

00.10.70.00.UD.BB

IP A d dr

IQ3 -400007096

M A C Ad d r

00.10.70.00.UD.BB

IP A d dr

100-240 V

7 8 9

+ 0

S/No:

Location

S/No:

LA N

3

Q3B____X73010003

16 17 18

13 14 15

10 11 12

5

6

4

+ 0

M A C A d d r I P A d d r

00.10.70.00.UD.BB

IQ3 -400007096

M A C A d d r

00.10.70.00.UD.BB

O /S

11

P 0

OK RX

31 32 33

P

24 V

0 V

16

15

13

12

14A

P 0

34 35 36

37 38 39

43 44 45

46 47 48

40 41 42

I P A d d r

S/No:

Q3B____X73010003

Location

S/No:

Q3B____X73010003

L A N

O / S

IP Address, Location, Lan, Outstation address

recommended e.g. location/identifier

Tear off Label Strip

19

00.10.70.00.UD.BB

IQ3 -400007096

00.10.70.00.UD.BB

S/No:

Location

S/No:

Q3B____X73010003

L A N

O / S

M A C A d d r I P A d d r

M A C A d d r

I P A d d r

20

for IQ3../.../LAN/...

Configure Auxiliary Board

if fitted (not battery board, XCITE/BBC)

for IQ3../.../XNC/..., including IQ3../.../LAN/XNC/..., IQ3../.../SER/XNC/...

IQ3../.../XNC/... Installation Instructions TG200911, section 2

SET Manual TE200147 IQ3 Configuration Manual TE200768

21

IQ3../.../LAN/... Installation Instructions TG200916, section 2

Configure IQ3 for BACnet Protocol

If IQ3/BAC and BACnet protocol communications required.

1 Connect SET to use Ethernet as Step 22 below 2 Setup SET to browse BACnet; this requires the BACnet network driver to be installed. 3 Note the Virtual Port ID and Virtual Network Number. 4 Create a BACnet network in the System View and enter the Virtual Port ID and Virtual Network Number into the BUA (BACnet

Universal Address). 5 Browse BACnet. The default settings of the Network module 3 (type 5, BACnet) will normally allow BACnet communications to operate correctly, but under certain circumstances some parameters may need to be changed as described in the table below:

retemaraPgnitteStluafeDnoitcnuF retemarapegnahcotyrassecennoitidnoC

elbasiD elu

doM

eciveD

ecnatsnI

launaM

ecived

ecnatsni

krowteN

rebmuN

troPPDU53556ot0,rebmuntrop

3eludoMkrowteN

DMBB

)5epyt-tenCAB(

el

banE

tama-IdneS

putrats

elbatTDB

PIetomeR

ot(1sserddA

)23

elbatTDB

etomeR

)23

ksaM

ot(1tenbuS

elbatTDB

PDUetomeR

)23ot(1

)1/0(elbasiD/elbanE)0(delbanE

303914ot1,ecnatsnI

)1/0(launaM/citamotuA

53556ot

1,krowteN1

lacoldna

sserdda

c

itamotuA

)0(

80874

tenCAB

fonoitcnuF

rebmunnaL

QIfosserddA

ebtsum

.sediser

'0CAB'xeh

tropPDUemas

)1/0(elbanE/elbasiD)0(delbasiD

sserddaPI

552.552

.552.552ot0.0.0.0

552.552.552.552ot0.0.0.0

knalbsserddaPI:sDMBBfoelbaT

knalb

53556ot0knalbdesutrop-tropPDU:sDMBBfoelbaT

.metsystenCABno3

.yllaunamtes

.sretuorssorcotsegassem

rebmuntenbusetareneg

nognitacinummocmorf3QIehtelbasidlliwsihT

lliwcitamotuaottesecnatsniecivedlaunaMfI

)sserddalacol+0001xrebmunnaL(lauqe

detaluclacsiecnatsnIeciveDeht,citamotuanI

launamnI.sserddalacoldnarebmunnaLmorf

3QIehthcihwnorebmunkrowtentenCABehT

llA.snoitacinummoctenCABrofdesutroPPDU

esutsu

mtnemgesemasnosecivedtenCAB

tsacdaorBPItenCABsatcaot3QIselbanE

tsacdaorbelbaneot.e.i,eciveDtnemeganaM

foseci

vedtenCABrehtoyfitonot3QIelbanelliW

.putratstakrowtenehtnoecneserpsti

otdesuksam-ksamtenbus:sDMBBfoelbaT

tenCABpotsoT

gnidnif

metsys

isrehtoehtkrowtena

.tenbusemasnoetarepo

putratstaerawtfos

eriuqer

retuorafo

tluaf.g.e,snoitacinummoc

eciveDdetaluclacyllacitamotuaehtfI

tenCABehtnotneserpydaerlasiecnatsnI

eciveDdetaluclacyllacitamotuaehtfI

tenCABehtnotneserpydaerlasiecnatsnI

no.g.e(desuydaerlasi1rebmunkrowtenfI

.)retuorafoed

otderiuqererasecivedteNCABfostesowtfI

.tnemgestenCABnoDMBBrehtoonfI

esutahtsecivedhtiwkrowtonlliwDMBB

hcusrednu,gnisserddaPIcitamotua

delbasidtfelebdluohssnoitidnoc

ehtnoecneserps'3QIfonoitacifitonfI

lootdnayroisvrepusottnesebotsikrowten

saesehtputes,delbanesiDMBBfI

edisrehtoehttenbushcaerofeno,d

Other modules that may need to be configured are Alarm Destination module (type 4 BACnet), IC Comms module (BACnet protocol type) and Non-Trend Device Modules (NTDs) for use with IC Comms. Once SET is browsing the BACnet system, NTD data can be dragged onto the Device View to setup the NTDs. Certain issues exist when using automatic IP addressing and

BACnet protocol (see IQ3 Configuration manual Pt. 1 section 3.7.4)

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

9

IQ3xact Installation Instructions

4 Installation - Configuration (continued)

Configure IQ3

22

Either using Ethernet

Note that downloading IQ3 strategy file is possible through the IQ3’s virtual CNC once the virtual CNC address is set up, and if IP addressing is set up correctly in both PC and IQ3.

either

Or using current loop Lan (IQ3/LAN only)

Note that only the strategy file can be downloaded using the current loop Lan or RS232 port (not language, backdrop or XNC files)

Configure IQ3 strategy using SET and download strategy file and other configuration files (language, backdrop, XNC (IQ3/XNC only) from SET

or

local PC (Ethernet) connection can be either to adjacent

SET v6.2

standard Ethernet connection see section 3 step 5

Ethernet

Router

IQ3

standard Ethernet cable - see section 3 step 5

IQ3/LAN

current loop

Lan

Ethernet hub using standard cable only, or directly to IQ3 using standard cable and crossover adaptor, XCITE/XA.

SET v6.2

Note that for SDU-xcite, local supervisor port address should be zero, and if SDU<v1.01 firmware is used, label lengths must be restricted to 20 characters; SDU-xcite v1.01 truncates labels to first 20 characters. Note that for RD-IQ, local supervisor port address should be zero, and by default the following strategy items are used: Local temperature; S9, Setpoint; K1, Occupation status; K6, Fan speed status; K7. The items used can be changed using RD’s buttons

100-240 V

XCITE/XA crossover adaptor order separately (XCITE/XA/5 pack of 5)

SET Manual TE200147 IQ3 Configuration Manual TE200768

OK RX

RJ45

23

Configure SET to browse the BACnet system as described in step 21 above.

Use SET to check that IQ3 BACnet functionality is operating by checking it appears correctly in the System View on its BACnet network.

Check IQ3 on BACnet

If IQ3/BAC and BACnet protocol communications are required

10

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

Installation Instructions IQ3xact

IQ3

S

4 5 6

2

7 8 9

3

10 11 12

4

13 14 15

5

16 17 18

6

+ 0

1 2 3

1

+ 0

0 V

24 V

34 35 36

12

37 38 39

13

40 41 42

14A

31 32 33

P

11

43 44 45

15

46 47 48

16

100-240 V

OK RX

P 0

S

IQ3

4 5 6

2

7 8 9

3

10 11 12

4

13 14 15

5

16 17 18

6

+ 0

1 2 3

1

+ 0

0 V

24 V

34 35 36

12

37 38 39

13

40 41 42

14A

31 32 33

P

11

43 44 451546 47 48

16

100-240 V

OK RX

P 0

4 Installation - Configuration (continued)

24

Switch off

a

Switch on

c

25

Switch off

a

Test Inputs

Test Outputs

b

O

I

b

O

I

d

ΔT = X

O

I

(yellow)

Switch on

4 5 6

16 17 18

13 14 15

1 2 3

10 11 12

7 8 9

3

5

1

+ 0

6

2

4

+ 0

c

O

100-240 V

OK RX

P

24 V

0 V

16

15

13

11

12

14A

P 0

34 35 36

31 32 33

37 38 39

43 44 45

46 47 48

40 41 42

I

d

4 5 6

16 17 18

13 14 15

1 2 3

10 11 12

7 8 9

3

5

1

+ 0

6

2

4

+ 0

e.g. VB

(yellow)

100-240 V

OK RX

24 V

0 V

16

15

13

11

12

14A

P 0

34 35 36

31 32 33

37 38 39

43 44 45

46 47 48

40 41 42

P

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

11

IQ3xact Installation Instructions

4 Installation - Configuration (continued)

Connect Supervisors/Tools/Display Panels

26

RS232 Local Supervisor

963 v2.1, SET v6.2, 916, IQView

• Trend text comms only, no upload/download (e.g. SET live edit only).

100-240 V

RD-IQ,

SDU-xcite

OK RX

RJ11

oror

963 v2.1, SET v6.2,

916

• Use Lan No, Outstation address.

• Set local supervisor port address to non-zero for network access

SDU-xcite, RD-IQ

• Set local supervisor port address to zero

• For RD-IQ, strategy must use particular strategy items (see step 22)

IQView

RJ11

CABLE/EJ105650

RJ11

IQ3

RD-IQ, SDU-xcite

RJ11

RD/SDU-IQ3COMMSCABLE/3M RD/SDU-IQ3COMMSCABLE/10M

Ethernet, Local Subnet

Router

Ethernet

Router

IQ3

963 v2.1, SET v6.2, 916, IQView

• Connect using virtual CNC in IQ3 or 3xtend/EINC L (IQView can use its integral vCNC).

• Virtual CNC must be set up in IQ3 or 3xtend/EINC L (or IQView).

• PC must be set up for IP addressing (use host name if automatic addressing being used).

• Software must be set up with IP address (or host name if automatic addressing being used) of virtual CNC and CNC port number.

• PC and virtual CNC must be on same subnet (same subnet mask).

• Software talks to IQ3 Lan No, Oustation address using vCNC.

Web Browser (Internet Explorer v6)

• PC must be set up for IP addressing.

• PC and IQ3 must be on same subnet (same subnet mask).

• Browser talks to IQ3 IP address (or host name if automatic addressing being used).

• For Windows XP SP1, download the Sun Java runtime environment v1.4 (or greater) from Java.com

Current loop (IQ3/LAN only)

963 v2.1, SET v6.2, 916

IQ3/LAN

IQView

current loop

Lan

PC (963 v2.1, SET v6.2, 916)

IQ3

RJ11

9 Way D type female

RJ11

CABLE/EJ101422

Ethernet, Remote Subnet (across Routers)

Router

IQView

963 v2.1, SET v6.2, 916, IQView

Set up as adjacent except

• Set up default router in PC and IQ3.

• PC and IQ3 are on different subnets.

• WINS server(s) must be set up if host names being used across routers.

Web Browser (Internet Explorer v6)

Set up as adjacent except

• Set up default router in PC and IQ3.

• PC and IQ3 are on different subnets.

• WINS server(s) must be set up if host names being used across routers.

IQ3

Ethernet

12

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

Installation Instructions IQ3xact

4 Installation - Configuration (continued)

Close Panel

27

IQ3XACT/12/USA/UL/.../24 is UL rated as ‘UL916 listed open energy management equipment’.

4 5 6

16 17 18

1 2 3

13 14 15

19 20 21

22 23 24

25 26 27

10 11 12

7 8 9

3

1

2

+ 0

100-240 V

28 29 30

5

6

8

9

10

4

7

+ 0

+ 0 + 0+ 0

+ 0

A

16

13

11

12

14A

P 0

OK RX

34 35 36

37 38 39

31 32 33

43 44 451546 47 48

40 41 42

P

24 V

0 V

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

13

IQ3xact Installation Instructions

5 Replacing the Battery (if required and if auxiliary board fitted)

Check Auxiliary Board

1

if XCITE/BBC got to step 2 below

if IQ3../.../LAN/...

transfer to IQ3../.../LAN/... Installation Instructions TG200916 section 3

if IQ3../.../XNC/..., including IQ3../.../LAN/XNC/..., IQ3../.../SER/XNC/...

Switch Off

2

O

I

Open Panel

4

WARNING: Opening the panel may expose

dangerous voltages.

417-IEC-5036

4 5 6

1 2 3

1

2

+ 0

100-240 V

3

16 17 18

13 14 15

19 20 21

25 26 27

10 11 12

22 23 24

7 8 9

28 29 30

3

5

6

8

9

10

4

7

+ 0

+ 0 + 0 + 0

+ 0

A

16

13

11

12

14A

P 0

OK RX

34 35 36

31 32 33

37 38 39

43 44 451546 47 48

40 41 42

P

24 V

0 V

Isolate I/O

4 5 6

1 2 3

1

+ 0

100-240 V

16 17 18

13 14 15

10 11 12

7 8 9

3

5

2

6

4

+ 0

OK RX

24 V

a

transfer to IQ3../.../XNC/... Installation Instructions TG200911 section 2.2

O

I

16

15

13

11

12

14A

P 0

34 35 36

31 32 33

37 38 39

43 44 45

46 47 48

40 41 42

P

24 V

0 V

Remove Auxiliary Board Cover

5

O

I

WARNING: The connecting leads

may be connected to supplies. Isolate before touching.

b

c

Replace Battery

6

b

Replace Auxiliary

7

Board Cover

a

c

CR 2032

CR2032 3V

CR 2032

Warning: The lithium battery

+

must not be recharged, disassembled, burnt or short circuited. Misuse may cause

explosion or fire. Dispose of carefully. Refer to Health and Safety Executive Guidance Note GS43. See section 6, Disposal, below.

14

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

Installation Instructions IQ3xact

5 Replacing the Battery (continued)

8

4 5 6

16 17 18

1 2 3

13 14 15

19 20 21

22 23 24

25 26 27

10 11 12

7 8 9

28 29 30

3

5

6

8

9

10

1

2

4

7

+ 0

+ 0 + 0 + 0

+ 0

A

100-240 V

IQ3XACT/12/USA/UL/.../24 is UL rated as ‘UL916 listed open energy management equipment’.

16

13

11

12

14A

P 0

OK RX

34 35 36

37 38 39

31 32 33

43 44 451546 47 48

40 41 42

P

24 V

0 V

9

Reconnect Supply to I/OClose Panel

Switch On

10

O

I

4 5 6

16 17 18

13 14 15

1 2 3

10 11 12

7 8 9

3

5

1

+ 0

100-240 V

6

2

4

+ 0

16

15

13

11

12

14A

P 0

OK RX

24 V

0 V

P 0

34 35 36

31 32 33

37 38 39

43 44 45

46 47 48

40 41 42

P

24 V

O

I

O

I

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

15

IQ3xact Installation Instructions

6 Disposal

WEEE Directive :

At the end of their useful life the packaging, product, and any battery should be disposed

Do not dispose of with normal household waste. Do not burn.

of by a suitable recycling centre.

Please send any comments about this or any other Trend technical publication to techpubs@trendcontrols.com

© 2008 Honeywell Technologies Sàrl, ECC Division. All rights reserved. Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Ecublens, Route du Bois 3, Switzerland by its Authorized Representative, Trend Control Systems Limited.

Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes.

Trend Control Systems Limited

P.O. Box 34, Horsham, West Sussex, RH12 2YF, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www.trend-controls.com

Trend Control Systems USA

6670 185th Avenue NE, Redmond, Washington 98052, USA. Tel: (425)897-3900, Fax: (425)869-8445 www.trend-controls.com

16

IQ3xact Web Enabled Controller Installation Instructions TG200766 Issue 2 21/04/08

TREND IQ3xact User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual