TREND HR/JIG Instruction Manual

HR/JIG

Please read these instructions before use.

HR/JIG

Dear Customer

Thank you for purchasing this Trend product,
we hope you enjoy many years of creative and
productive use.

Please remember to return your guarantee card
within 28 days of purchase.

CONTENTS

TECHNICAL DATA _____________________ 1
SAFETY ____________________________2-3
ITEMS ENCLOSED ____________________ 4
DESCRIPTION OF PARTS _______________ 5
ACCESSORIES

- Recommended Cutters _________________ 6

- Sub-base Set ________________________ 6

- Guide Bush __________________________ 7

- Clamps _____________________________ 7

- Carry Case __________________________ 7

ASSEMBLY

- Fitting Location Pins ___________________ 8

- Marking Out for Hot Rods _______________ 8

OPERATION

- Positioning Jig on Worktop ______________ 9

- Setting the Depth of Cut _______________ 10

- Routing the Grooves __________________ 10

- Fitting Hot Rods _____________________ 11

MAINTENANCE ______________________ 11
ENVIRONMENTAL PROTECTION________ 11
GUARANTEE ________________________ 11
SPARE PARTS

– Spare Parts List _____________________ 12
– Spare Parts Diagram _________________ 12

TROUBLE SHOOTING _________________ IB

TECHNICAL DATA

Jig thickness 12mm
Cutter size R6.35mm or R6mm

cove (radius)
Guide bush size 30mm
Slot lengths 100mm, 200mm,

300mm, 400mm
Slot pitch 50mm
Weight 3.5kg

The following symbols are used throughout this
manual:

Denotes risk of personal injury, loss
of life or damage to the tool in case of
non-observance of the instructions in
this manual.

Refer to the instruction manual of
your power tool.

This unit must not be put into service until it has
been established that the power tool to be
connected to this unit is in compliance with
2006/42/EC (identified by the CE marking on
the power tool).

INTENDED USE

This jig is intended to be used with a plunge
router fitted with suitable cutter and guide bush
to rout grooves in solid timber or solid surface
worktops for stainless steel hot rods.

%

If you require further safety advice,
technical information or spare parts,
please call Trend Technical Support or
visit www.trend-uk.com

-1-

HR/JIG

SAFETY

WARNING:

Observe the safety regulations in the
instruction manual of the power tool
to be used. Please read the following
instructions carefully. Failure to do so
could lead to serious injury. When using
electric tools, basic safety precautions,
including the following should always be
followed to reduce the risk of fire, electric
shock and personal injury. Also observe
any applicable additional safety rules.
Read the following safety instructions
before attempting to operate this product.

PLEASE KEEP THESE
INSTRUCTIONS IN A SAFE PLACE.

The attention of UK users is drawn
to The Provision and Use of Work
Equipment Regulations 1998, and any
subsequent amendments.

Users should also read the HSE/HSC
Safe Use of Woodworking Machinery
Approved Code of Practice and Guidance
Document and any amendments.

Users must be competent with
woodworking equipment before using our
products.

IMPORTANT NOTE:

Residual Risk. Although the safety
instructions and operating manuals for
our tools contain extensive instructions
on safe working with power tools, every
power tool involves a certain residual risk
which cannot be completely excluded
by safety mechanisms. Power tools
must therefore always be operated with
caution!

General

1. Disconnect power tool and

attachment from power supply
when not in use, before servicing,
when making adjustments and
when changing accessories such
as cutters. Ensure switch is in “off”
position. Always ensure cutter has
stopped rotating.

2. Always mount the power tool,

accessory or attachment in
conformity with the instructions. Only
use attachment and accessories
specified in the power tool manual.
The tool or attachment should not be
modified or used for any application
other than that for which it was
designed. Do not force tool.

3. Keep children and visitors away. Do

not let children or visitors touch the
tool, accessory or attachment. Keep
children and visitors away from work
area. Make the workshop child proof
with padlock and master switch.

4. Dress properly. Do not wear loose

clothing or jewellery, they can be
caught in moving parts. Rubber
gloves and non-skid footwear
is recommended when working
outdoors. Wear protective hair

covering to contain long hair.

5. Consider working environment. Do

not use the product in the rain or in
a damp environment. Keep work
area well lit. Do not use power tools
near gasoline or flammable liquids.
Keep workshop at a comfortable
temperature so your hands are
not cold. Connect machines that
are used in the open via a residual
current device (RCD) with an
actuation current of 30 mA maximum.
Use only extension cables that are
approved for outdoor use.

6. The accessory or attachment must

be kept level and stable at all times.

7. Keep work area clean. Cluttered

workshops and benches can cause
injuries. Ensure there is sufficient
room to work safely.

8. Secure idle tools. When not in use,

tools should be stored in a dry and
high or locked up place, out of reach
of children.

9. For best control and safety use

both hands on the power tool and
attachment. Keep both hands away
from cutting area. Always wait for the
spindle and cutter to stop rotating
before making any adjustments.

10. Always keep guards in place and in

good working order.

11. Remove any nails, staples and other

metal parts from the workpiece.

12. Maintain tools and cutters with care.

Keep cutters sharp and clean for
better and safer performance. Do
not use damaged cutters. Follow
instructions for lubricating and
changing accessories. Keep handles
dry, clean and free from oil and
grease.

13. Maintain accessories. Do not use

damaged accessories. Only use
accessories recommended by the
manufacturer.

14. Check damaged parts. Before

operation inspect the attachment,
the power tool, the cable, extension
cable and the plug carefully for signs
of damage. Check for alignment of
moving parts, binding, breakage,
mounting and any other conditions
that may effect its operation.
Have any damage repaired by an
Authorised Service Agent before
using the tool or accessory. Protect
tools from impact and shock.

15. Do not use tool if switch does not

turn it on or off. Have defective
switches replaced by an Authorised
Service Agent

16. Don’t over reach. Keep proper

footing and balance at all times. Do
not use awkward or uncomfortable
hand positions.

17. Don’t abuse the cable.Never carry

-2-

power tool or accessory by cord or
pull it to disconnect from the socket.
Keep cord from heat, oil and sharp
edges. Always trail the power cord
away from the work area.

18. Connect dust extraction equipment.

If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used.

19. Check all fixing and fastening nuts,

bolts and screws on power tool,
attachment and cutting tools before
use to ensure they are tight and
secure. Periodically check when
machining over long periods.

20. Stay alert. Watch what you are

doing. Use common sense. Do not
operate tools when you are tired,
under the influence of drugs or
alcohol.

21. Personal Protective Equipment

(PPE) for eye, ear and respiratory
protection must be worn. All PPE
must meet current UK and EU
legislation.

22. Do not leave tools running

unattended. Do not leave tool until it
comes to a complete stop.

23. Always clamp workpiece being

machined securely.

24. Only use cutting tools for

woodworking that meet EN847­1/2 safety standards, and any
subsequent amendments.

25. Vibration levels. Hand held power

tools produce different vibration
levels. You should always refer
to the specifications and relevant
Health & Safety Guide.

Routing Safety

1. Read and understand instructions

supplied with power tool, attachment
and cutter.

2. Keep hands, hair and clothing clear

of the cutter.

3. Remove adjusting keys and

spanners. Check to see that keys
and adjusting spanners are removed
from the router tool, cutter and
attachment before turning router on.
Make sure cutter can rotate freely.

4. Noise. Take appropriate measures

for the protection of hearing if
the sound pressure of 85dB(A) is
exceeded. Routing sound pressure
may exceed 85dB(A), so ear
protection must be worn.

5. Eye protection. Always wear eye

protection in the form of safety
goggles, spectacles or visors to
protect the eyes.

6. Respiratory protection. Wear a

face or dust mask, or powered
respirator. Dust masks/filters should
be changed regularly.

HR/JIG

7. Do not switch router on with the

cutter touching the workpiece. At the
end of the cut, release the router
plunge and allow spindle to stop
rotating. Never use the spindle lock
as a brake

8. The direction of routing must always

be opposite to the cutter’s direction

of rotation. Do not back-cut or climb­cut.

9. Check before cutting that there

are no obstructions in the path of
the router. Ensure there are no
obstacles beneath workpiece when
cutting full thickness, and that a
sacrificial work surface is used.

Router Cutter Safety

1. Cutting tools are sharp. Care should

be taken when handling them. Do not
drop cutters or knock them against
hard objects. Handle very small
diameter cutters with extra care.
Always return cutter to its packaging
after use.

2. Always use cutters with a shank

diameter corresponding to the size of
the collet installed in your tool.

3. The maximum speed (n.max) marked

on the tool, or in instructions or on
packaging shall not be exceeded.
Where stated the speed range shall
be adhered to. Recommended
speeds are shown in the Trend
Routing Catalogue and/or website.

4. Always use router cutters in a router.

Drill and boring bits must not be
used in a router. Router cutters
must only be used for the material
cutting application for which they are
designed. Do not use on metal or
masonry.

5. Never use cutters with a diameter

exceeding the maximum diameter
indicated in the technical data of the
powertool or attachment used.

6. Before each use check that the

cutting tool is sharp and free from
damage. Do not use the cutting tool
if it is dull, broken or cracked or if in
any other damage is noticeable or
suspected.

7. Cutters should be kept clean. Resin

build up should be removed at
regular intervals with Resin Cleaner.
The use of a PTFE dry lubricant will
reduce resin build up. Do not use
PTFE spray on plastic parts.

8. When using stacked tooling (multi-

blade, block and groover etc.) on a
spindle arbor, ensure that the cutting
edges are staggered to each other to
reduce the cutting impact.

9. Cutter shanks should be inserted

into the collet all the way to the line
indicated on the shank. This ensures
that at least 3⁄4 of the shank length
is held in the collet. Ensure clamping

surfaces are cleaned to remove dirt,
grease, oil and water.

10. Observe the correct assembly and

fitting instructions in the router
instruction manual for fitting the
collet, nut and cutter.

11. Tool and tool bodies shall be

clamped in such a way that they will
not become loose during operation.
Care shall be taken when mounting
cutting tools to ensure that the
clamping is by the shank of the
cutting tool and that the cutting
edges are not in contact with each
other or with the clamping elements.

12. It is advisable to periodically check

the collet and collet nut. A damaged,
worn or distorted collet and nut can
cause vibration and shank damage.
Do not over-tighten the collet nut

13. Do not take deep cuts in one pass;

take several shallow or light passes
to reduce the side load applied to the
cutter and router. Too deep a cut in
one pass can stall the router.

14. In case of excessive vibrations whilst

using the router stop immediately
and have the eccentricity of the
router, router cutter and clamping
system checked by competent
personnel

15. All fastening screws and nuts should

be tightened using the appropriate
spanner or key and to the torque
value provided by the manufacturer.

16. Extension of the spanner or

tightening using hammer blows shall
not be permitted.

17. Clamping screws shall be tightened

according to instructions provided by
the manufacture. Where instructions
are not provided, clamping screws
shall be tightened in sequence from
the centre outwards.

Using Routers In A Fixed Position

1. Attention should be made to the

HSE’s Safe Use of Vertical Spindle

Moulding Machines Information
Sheet No.18 and any revisions.

2. After work, release the router plunge

to protect the cutter.

3. Always use a push-stick or push-

block when making any cut less than
300mm in length or when feeding the
last 300mm of the cut.

4. The opening around the cutter

should be reduced to a minimum
using suitably sized insert rings in
the table and closing the back fence
cheeks or fitting a false fence on the
back fence.

5. Whenever possible use a work

holding device or jig to secure
component being machined. Ensure
any attachment is securely fitted to
the workbench, with table surface at

-3-

approximately hip height.

6. Use a No-Volt Release Switch.

Ensure it is fixed securely, easily
accessible and used correctly.

7. In router table (inverted) mode, stand

to the front right of the table. The
cutter will rotate anti-clockwise when
viewed from top so the feed direction
is from the right (against the rotation
of the cutter). In overhead mode,
stand to the front left of the machine
table and the feed direction is from
the left.

8. Do not reach underneath table or

put your hands or fingers at any
time in the cutting path while tool is
connected to a power supply.

9. Never thickness timber between the

back of the cutter and the backfence.

Useful Advice When Routing

1. Judge your feed rate by the sound

of the motor. Feed the router at a
constant feed rate. Too slow a feed
rate will result in burning.

2. Trial cuts should be made on waste

material before starting any project.

3. When using some attachments e.g.

a router table or dovetail jig, a fine
height adjuster is recommended.

4. When using a template guide bush,

ensure there is sufficient clearance
between cutter tip and inside edge
of bush and that it cannot come into
contact with collet and nut. Ensure
cutter and guide bush are concentric.

Router Cutter Repair/Maintenance

1. Repair of tools is only allowed in

accordance with the manufacturers
instructions.

2. The design of composite (tipped)

tools shall not be changed in process
of repair. Composite tools shall be
repaired by a competent person i.e.
a person of training and experience,
who has knowledge of the design
requirements and understands the
levels of safety to be achieved.

3. Repair shall therefore include, e.g.

the use of spare parts which are in
accordance with the specification
of the original parts provided by the
manufacturer.

4. Tolerances which ensure correct

clamping shall be maintained.

5. Care shall be taken that regrinding

of the cutting edge will not cause
weakening of the body and the
connection of the cutting edge to the
body.

Version 7.2 06/2013

ITEMS ENCLOSED

HR/JIG

100

200

300

400

x4

ITEMS REQUIRED

n 1/2” plunge router with suitable size

collet fitted.

n R6.35mm (12.7mmØ) or R6mm

(12mm Ø) cove (radius) cutter
depending on hot rod diameter*.

n 30mm guide bush.

n Trestles x 2.

n Clamps x 3.

*Other hot rod diameters are available on
the market, please choose a suitable cove
cutter to suit.

HR/JIG

x1

300

x1

200

100

HR/JIG

x1

GUARANTEE

Ref. UNIBASE

For certain makes of router a sub-base
will be required to allow the guide bush to
be fitted.

-4-

DESCRIPTION OF PARTS

F FF F F

F

F

HR/JIG

E

B K IJCD

100

200

300

300

200

A

H

400

L

F+G

G

G

G

G

G

A Jig body

B 100mm hot rod slot

C 200mm hot rod slot

D 300mm hot rod slot

E 400mm hot rod slot

F Pin holes for 90º to worktop edge

G Pin holes for 45º to worktop edge

H Slot size engravings

I Engraved lines at 45˚

J Engraved lines for middle of slot

K Engraved lines for centre of slot

L Engraved lines for actual hot rod length

M Pin

100

BCD

M

-5-

ACCESSORIES

Please use only Trend original accessories.

Recommended Cove Cutter R6.35mm
for 12.7mmØ Rods

Ref. C054AX1/2TC

Recommended Cove Cutter R6mm
for 12mmØ Rods

Ref. C053CX1/2TC

Please see Trend catalogue for other sizes
of cove cutter to suit other rod diameters on
the market.

Sub-base Set

Ref. UNIBASE

To obtain a perfect accurate close fitting joint,
a 30mm guide bush must be used. The guide
bush must always be fitted concentric with the
cutter. This can be achieved using a Universal
Sub-base and 30mm outside diameter guide
bush ref. GB30.

The Universal Sub-base has a central recess
to allow fitting of the guide bush to most makes
of routers and is available ready to fit the most
popular makes.

The Sub-base contains screws, a line up bush
and two line up pins. The line up pins and bush
ensure exact alignment of Sub-base with router
spindle, when fitted with the relevant collet.

General Instructions for Fitting
Sub-bases to Router

1. Fit line up guide bush onto sub-base, with
screws supplied.

2. Fit 12.7mm (1/2”) shank line up pin into collet
of router. Plunge router until pin projects
through base and lock plunge.

3. Locate guide bush and sub-base assembly
over protruding pin.

4. Line up fixing holes and fit screws. Now
tighten up screws.

5. Remove line up bush and line up pin.
Alignment should now be correct. Fit 30mm
guide bush and cutter.

6. Periodically check the sub-base is concentric
to the spindle of the router.

HR/JIG

C054AX1/2TC

C053CX1/2TC

UNIBASE

Fits following router models

Atlas Copco OFSE2000 Bosch GOF 1300ACE, 1600A,
1700ACE Casals FT2000VCE DeWalt DW625EK, 629
Draper R1900V Elu MOF 31, 77, 98, 131, 177(E) Felisatti
TP246(E), R346EC Festo OF2000E Freud FT2000E

Hitachi MI12V, M12SA, TR12 Makita 3612BR, 3612(C)
Metabo OF1612, OFE1812 Performance Pro CLM1250R

>11/2003, CLM2050R Ryobi RE600N, R600N, RE601, R500,
R502 Skil 1875U1 T-TECH TT/R127 Wadkin WW

-6-

30mm Guide Bush

Ref. GB30/A

Clamps

Ref. FC/200
Three heavy duty quick action or gripper
clamps are required to secure the jig to
the worktop.

Whenever fast action clamps are used,
ensure they do not foul the router path
and that they are securely tightened.

Carry Case

Ref. CASE/DG
Large carry case to hold and transport the Hot
Rod Jig.

Case has hard carry strap, removable shoulder
strap and accessory pouch.

HR/JIG

m

m

0

3

R

d

n

e

r

t

-7-

HR/JIG

Custom design Custom design

ASSEMBLY

Fitting Location Pins

The jig has sets of pin holes to allow the jig to be

accurately positioned at 90˚ or 45˚ to the worktop

edge. The pin holes are at 50mm centres.

Location pins are tapered to ensure a good tight
fit in hole. Insert the smallest end of the pin into
the hole by lightly pushing. Ensure pins are fully
home before use and head is below surface.
When using jig ensure location pins do not foul
workbench.

Pin

Marking Out for Hot Rods

The jig has a series of engraved lines on one
side that allow the jig to sighted to lines drawn
on the worktop.

The jig slots allow for certain hot rod lengths to
be routed.

For complicated hot rod slots the jig will need to
be repositioned and the routed slot length limited
by using a user made stop or to a pencil line.
Careful marking out will be required.

worktop

edge

50mm90º to

45º to

worktop

edge

50mm

At 90º to Worktop Edge

Custom design

At 45º to Worktop Edge

100

200

300

400

300

200

100

Custom design Custom design

Ensure jig is lined up at an equal
distance from worktop edge.

-8-

OPERATION

= Pin

Positioning Jig on Worktop

n After choosing which design is required,

locate the pins in the necessary holes.

n Using two of the pins provided in the relevant

pin holes locate the jig against the front of the
worktop.

n For repeat slot designs, or custom designs

use the engraved sight lines on the jig to
set the jig to the marked lines drawn on the
worktop. Ensure spacing between each slot is
equal.

n Secure the jig with clamps, ensure clamps do

not foul router path.

Positioning for 90º to Worktop Edge

400

300

300

200

100

200

100

HR/JIG

Ensure working position is
comfortable. Keep proper footing at
all times.

Ensure worktop is held securely
to trestles. Ensure jig is clamped
securely to worktop and placed at a
suitable and comfortable work height.

Clamp

ClampWorktop edge Clamp

Positioning for 45º to Worktop Edge

100

200

300

Worktop edge

= Pin

Ensure jig is lined up at an equal
distance from worktop edge.

400

300

200

100

Make trial cuts on waste material
before using jig on actual worktop.

-9-

Setting the Depth of Cut

n The preferred method of recessing slots

for hot rods is to cut one third to half the
diameter in depth of the hot rods. For
example for 12mm diameter rods the cut
depth is 4-6mm deep.

n Ensure router has correct size of guide bush

and cutter fitted.

n Plunge router down until the cutter is just

touching the worktop.

n Now set the depth of cut required depending

on the diameter of the hot rod.

n Release router plunge.

n Make a trial cut on waste material first to

check recess depth and length of slots suits
the hot rods.

HR/JIG

Before cutting an actual worktop,
make trial cuts on a waste piece
of worktop to check groove depth
and spacing is correct and to allow
familiarisation of jig.

4-6mm

Feed Direction

Feed direction

Clamp

Jig

Worktop

Check slot depth and length in
a waste piece of material before
starting main cut.

Routing the Grooves

n Position the router in left hand side

of first slot.

n Switch on router and plunge down to depth

setting. Rout groove using a steady and
even feed speed. Ensure guide bush follows
the left side of the slot, do not rout back
down the slot.

n At the end of the cut release the plunge and

switch off the router. Reposition the router at
the beginning of the next slot.

n Repeat this operation for each slot in the jig

as required.

n When routing is complete remove any rough

edges with a fine grade adhesive paper.

Rout only in one direction, do not rout
back in the opposite direction.

-10-

Clamp

100

200

= Pin

400

300

Direction of
router feed

300

200

100

Clamp

Cutter rotation

Guide bush

Router cutter

HR/JIG

Fitting Hot Rods

n Place the hot rods into the recesses. Check
with hot rod manufacturers instructions for
fitting guidance, and suitable adhesive.

n Finish and seal worktop with an appropriate
sealer. Always follow the manufacturers
instructions

After use, store jig carefully.

MAINTENANCE

Please use only Trend original spare parts and
accessories.

The jig has been designed to operate over a
long period of time with a minimum amount of
maintenance. Continual satisfactory operation
depends upon proper tool care and regular
cleaning.

Cleaning

n Regularly clean the jig with a soft cloth.

Lubrication

n Your jig requires no additional lubrication.

Storage

n After use store jig in its packaging or it can be

hung on a wall hook.

n An accessory case is also available Ref.

CASE/DG.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing as
waste.

Packaging should be sorted for environmental­friendly recycling.
The product and its accessories at the end of their
life should be sorted for environmental friendly
recycling.

GUARANTEE

The jig carries a manufacturers guarantee in
accordance with the conditions on the enclosed
guarantee card.

-11-

HR/JIG

HR/JIG - SPARE PARTS DIAGRAM v1.0 03/2014

Please use only Trend original spare parts.

100

200

300

400

300

200

1

100

2 3

HR/JIG

HR/JIG - SPARE PARTS LIST v1.0 03/2014

No. Qty. Desc. Ref.

1 1 Hot Rod Jig HR/JIG
2 1 Pins 10mmØ (Pack of 4) KWJ/PIN/4
3 1 Manual MANU/HR

-12-

TROUBLE SHOOTING

HR/JIG

Fault

n Groove is too wide or too
narrow for the rods.

n Groove depth varies
between slots.

n Grooves are too shallow
for rods.

n Grooves are too deep for
rods.

n Groove in worktop is burnt.

n Jig is slipping on material.

Cause

Cutter or guide bush is the
incorrect diameter or cutter is
not running true.

Jig has lifted when routing.

Cutter has slipped in the collet
when routing.

Cut depth not deep enough.

Cut depth too deep.

Cutter is blunt.

Clamps are not secure.

Remedy

Check concentricity of cutter
and guide bush. Cutter should
be a radius cove cutter of
suitable diameter to suit hot
rods. A 30mm guide bush is
required.

Reposition clamps so jig does
not lift when routing. Ensure
router does not foul clamps.

Check cutter is being held
in the collet, replace collet if
necessary.

Reset cut depth depending on
diameter of rods. For example
for 12mm rods, between
4-6mm depth.

Replace worktop and reset cut
depth depending on diameter
of rods. For example for 12mm
rods, between 4-6mm depth.

Always use sharp cutters.

Check clamps for wear. Clamp
securely.

-IB-

-13-

Trend Machinery & Cutting Tools Ltd.

Odhams Trading Estate St Albans Road
Watford WD24 7TR England

Tel: [phone]

MANU/HR v 1.1

© Copyright Trend 2014. No part of this publication may be reproduced, stored or transmitted in any form without prior permission. Our
policy of continuous improvement means that specifications may change without notice. Trend Machinery and Cutting Tools cannot be

held liable for any material rendered unusable or any form of consequential loss. E&OE

RECYCLABLE

® All registered trademarks acknowledged.

[e-mail]
www.trend-uk.com