Trend D/STAND/A User guide

Door Stand

D/STAND/A

INST/DS/A v4.1

DOOR STAND
REF. D/STAND/A

Thank you for purchasing this Trend product,
which should give lasting performance if used in
accordance with these instructions.

The following symbols are used throughout these
instructions.

Denotes risk of personal injury, loss

of life or damage to the tool in case of
non-observance of the instructions.

Refer to the instruction manual of your

power tool.

INTENDED USE

This accessory is intended to be used to hold a
door on its edge, so that tools can be used to
plane, hinge recess and cut the mortise in the
door. The accessory will also allow the door to be
tilted back to aid fitting the door into the frame,
as well as keeping door stable while fitting door
furniture.

Maximum door thickness: 32mm to 55mm
(thinner doors require packing piece)

Maximum door size: 1981mm x 838mm
Maximum door weight: 50kg
Weight: 2.2kg

SAFETY

Please read and understand the safety points
at the end of these instructions as well as your
power tool instructions.

PLEASE KEEP THESE INSTRUCTIONS IN A
SAFE PLACE.

Users must be competent in using woodworking
equipment before using our products. Consider
working environment before using tools. Ensure
working position is comfortable and component
is clamped securely. Please keep children and
visitors away from tools and work area.
All tools have a residual risk so must therefore
be handled with caution.

ITEMS REQUIRED

n None required to use the stand.
n Tools required for working on the door.

DESCRIPTION OF PART S

A. Body

Soft pad

B.

Clamping knob

C.

Plastic cap for

D.
clamping knob

G

F

E. End pad
G. Hanging holes
F. Stabilisers
H. Instructions

A

D

C

H

G

BF

E

B

OPERATION

For Planing Door, Hinge Recessing
and Lock Mortising

n Place door stand on the floor. Unwind the

clamping knob.

n

Lay the door on its edge to suit door

hanging application (planing, door hinge
recessing or mortising).

n

Place the door edge into the door stand

and tighten the clamping knob by hand.
Do not over tighten.

n

Door is now held.

n

Carry out door application.

n

To remove the door, hold the door

securely and loosen the clamping knob on
the door stand. Lift the door slightly and
slide door stand away.

Regularly check that the door stand
clamping knob is tight.
Do not overtighten.

For Supporting Door While
Hanging in Frame

n After hinge recessing on door edge and

fitting hinges, ensure door stand clamping
knob is tight.

n

Carefully lift top edge of door and tilt back

the door using the door stand as a pivot.

n

Position the door into the frame or lining.

Simultaneously push the bottom of the
door in and pull top of the door out until top
hinge lines up with its recess. Locate and
secure with screws.

Hollow doors may require a load spread
plate made of MDF placed between the
plastic cap and the door to prevent door
damage.

PTO

© Trend Machinery & Cutting Tools Ltd. 2014, 2015, 2016
E&OE
® All trademarks acknowledged

Trend Machinery & Cutting Tools Ltd.

GB

Tel: [phone]
[e-mail]
www.trend-uk.com

USA

Trend Routing Technology
Inc.

Tel: [phone]
[e-mail]
www.trend-usa.com

RECYCLABLE

Top
hinge

Door
lining

Door tilt shown exaggerated.

n Move bottom of the door out, the door will

swing slightly then fit bottom hinge.

Remove the door stand by loosening the

n

clamping knob.

n

Fit the remaining screws into the hinges.

When door is held in door clamp in vertical
mode ensure door is always held by
operator’s hands. Do not leave door in the
stand unattended.

Ensure working position is comfortable.
Keep proper footing and balance at all
times.

For Fitting Door Furniture

n If there is a sufficient gap between the

bottom of the door and the floor, the door
stand can also be put on a hung door to
clamp the door while drilling a keyhole or
for fitting door furniture, such as handles.

n Open the door, place the door stand at the

bottom of door. Loosely tighten clamping
knob and then open the door fully so that
the stabiliser arms with end pads are
touching the skirting board. Tighten the
clamping knob. The door is now secure to
allow drilling of a keyhole, fitting handles
etc. Alternatively place your foot on one of
the stabilisers.

Internal wall

Door

Touching
skirting

Door stand

Stand here

n Once operation is complete, release the

clamping knob and remove the door stand.

After use, store accessory carefully.

SPARE PARTS

Please use only Trend original spare parts.

Item Qty. Desc. Ref. (1 off)

C 2 Knob M10 x 40mm Ball End WP-LOCK/06A

D 2 Plastic Cap For Ball End Stud WP-LOCK/08A
H 1 Instructions INST/DS/A

MAINTENANCE

Please use only Trend original spare parts
and accessories.

The accessory has been designed to operate
over a long period of time with minimum of
maintenance. Continual satisfactory operation
depends upon proper tool care and regular
cleaning.

Cleaning

n Keep the threads clear of resin build up.
n Regularly clean with a soft cloth.

Lubrication

n Your accessory requires no additional

lubrication.

Storage

n Always return product to its packaging

after use.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing
as waste.

Packaging should be sorted for environmental­friendly recycling. The product and its
accessories at the end of its life should be
sorted for environmental-friendly recycling.

GUARANTEE

All Trend products are guaranteed against
any defects in either workmanship or material,
except products that have been damaged due
to improper use or maintenance.

Safety Points

1. Disconnect power tool and attachment from power supply when not in
use, before servicing, when making adjustments and when changing
accessories such as cutters. Ensure switch is in “off” position and cutter
has stopped rotating.

2. Read and understand instructions supplied with power tool, attachment
and cutter.

3. Current Personal Protective Equipment (PPE) for eye, ear and
respiratory protection must be worn. Keep hands, hair and clothes
clear of the cutter.

4. Before each use check cutter is sharp and free from damage. Do not
use if cutter is dull, broken or cracked or if any damage is noticeable or
suspected.

5. The maximum speed (nmax) marked on tool or in instructions or on
packaging shall not be exceeded. Where stated, the speed range
should be adhered to.

6. Insert the shank into the router collet at least all the way to the marked
line indicated on the shank. This ensures at least 3/4 of shank length is
held in collet. Ensure clamping surfaces are clean.

7. Check all fixing and fastening nuts, bolts and screws on power tool,
attachment and cutting tools are correctly assembled, tight and to
correct torque setting before use.

8. Ensure all visors, guards and dust extraction is fitted.

9. The direction of routing must always be opposite to the cutter’s
direction of rotation.

10. Do not switch power tool on with the cutter touching the workpiece.

11. Trial cuts should be made in waste material before starting any project.

12. Repair of tools is only allowed according to tool manufacturers
instructions.

13. Do not take deep cuts in one pass, take shallow passes to reduce the
side load applied to the cutter.

Please see www.trend-uk.com/safety for more safety advice.

Our policy of continuous improvements mean that
specifications may change without notice. Trend
Machinery & Cutting Tools Ltd. cannot be held liable
for any material rendered unusable, or for any form of
consequential loss.