Trek P0621 User Manual

Trek Model P0621P / P0621N

High-Voltage/Power DC Amplifiers

Trek Model P0621P (+) / P0621N (-) is a high-voltage DC-stable
piezo driver/amplifier designed to provide precise control of
output voltages in ranges that are customer specified within a
range of available settings. It is configured as a noninverting
amplifier with a variable DC gain. An inverting amplifier
configuration is also available.

The unit features an all-solid-state design, a high slew rate and a
four-quadrant active output stage which sinks or sources current
into reactive or resistive loads throughout the output voltage
range. This capability is essential for achieving the accurate
output responses and high slew rates demanded by reactive
loads.

Key Specifications

! Output Voltage Range 0 to

! Output Current Range

! Slew Rate: Greater than 350 V/ (10% to 90%, typical)

Large Signal Bandwidth DC to greater than 3.5 kHz (1% distortion)

!
! Small Signal Bandwidth: DC to greater than 25 kHz (-3 dB)

DC Voltage Gain: 3000 V/V

!

+30 kV DC or peak AC (P0621P)
0 to -30 kV DC or peak AC (P0621N)
0 to ±20 mA DC or peak AC

µs

Typical Applications Include

! Closed-loop systems
! Automated or computer controlled systems

Features and Benefits

Four-quadrant

!

voltage range

Closed loop system for high accuracy

!

Short-circuit protected for equipment protection

!

All solid-state design for maintenance-free operation

!

DC-stable for programmable supply applications

!

NIST-traceable Certificate of Calibration provided with each unit

!

active output stage sinks or sources current into reactive or resistive loads throughout the output

TREK, INC. • 190 Walnut Street • Lockport, NY 14094 • USA • 800-FOR TREK

(fax) • www.trekinc.com • [e-mail] 716-438-7555 • 716-201-1804

Features

High Voltage On/Off

Local

Individual push-button switches

Remote

TTL high turns OFF the high voltage; TTL low
turns on the high voltage

Dynamics
Adjustments

Graduated 1-turn potentiometer used to
optimize the AC response for various load
parameters

Current Limit/Trip

Switch selectable for limit or trip. Graduated 1­turn potentiometer adjusts from 0 to 20 mA

Out of Regulation

LED illuminates and BNC provides a TTL low
when P0621 fails to produce HV output such as
during a current limit

Trip Status

LED illuminates and BNC provides a TTL low
when HV is disabled due to the output current
exceeding the current trip level, a high voltage
fault is detected or the top cover is removed

Fault Status

BNC provides a TTL low when P0621 is out of
regulation for greater than 500 ms

Mechanical

Dimensions

222 mm H x 432 mm W x 584 mm D
(8.75” H x 17” W x 23” D)

Weight

24.9 kg (55 lb)

HV Connector

Caton High Voltage Connector

BNC Connectors

Amplifier input, voltage monitor, current
monitor, remote HV ON/OFF, out of regulation,
fault/trip status

Operating Conditions

Temperature

0°C to 40°C (32°F to 104°F)

Relative Humidity

To 75%, noncondensing

Altitude

To 2000 meters (6561.68 ft.)

Electrical

Line Voltage

Factory Set for one of two ranges:
90 to 127 V AC or 180 to 250 V AC,
either at 48 to 63 Hz

AC Line Receptacle

Standard 3-prong with integral fuse holder

Power Consumption

1000 VA, maximum

Supplied Accessories

Operators’ Manual

PN: 23147

HV Output Cable

PN: 47067

Line Cord (for 104 to
127 V AC)

PN: N5011

Line Cord (for 180 to
250 V AC)

Selected per geographic destination

Models P0621P and N Specifications

Performance

Output Voltage
Positive Polarity
(P0621P)

0 to +30 kV DC or peak AC

Output Voltage
Negative Polarity
(P0621N)

0 to -30 kV DC or peak AC

Output Current

0 to ±20 mA

Input Voltage Range
(P0621P)

0 to +10 V DC or peak AC

Input Voltage Range
(P0621N)

0 to -10 V DC or peak AC
Input Impedance

50 kW, nominal

DC Voltage Gain

3000 V/V

DC Voltage Gain
Accuracy

Better than 0.1% of full scale
Offset Voltage

Less than ±4 V

Output Noise

Less than 5 V rms*

Slew Rate
(10% to 90%, typical)

Greater than 350 V/µs

Large Signal
Bandwidth
(1% distortion)

DC to greater than 3.5 kHz
Small Signal

Bandwidth (-3dB)

DC to greater than 25 kHz

Automatic Power
Limit

Automatically limits the internal power
dissipation to protect the Models P0621P and
P0621N from overheating

Voltage Monitor

Ratio

1/3000th of the HV output signal

DC Accuracy

Better than 0.1% of full scale

Offset Voltage

Less than ±2 mV

Output Noise

Less than 20 mV*

Output Impedance

47 W

Current Monitor

Ratio

0.5 V/mA

DC Accuracy

Better than 1% if full scale

Offset Voltage

Less than ±10 mV

Output Noise

Less than 30 mV rms*

Bandwidth

DC to greater than 10 kHz
Output Impedance

47 W

*Measured using the true rms feature of the HP Model 34401A digital multimeter

Copyright ã 2012 TREK, INC. All specifications are subject to change. 1251/JRB

Measurement and Power Solutions

TM

www.treki nc.co m