Tranwo Technology VSC5882 User Manual

VSC-5882A
5.8GHz Wireless Outdoor CMOS Camera
1107
Contents
FCC 0dBm CE 14dBm
1.Important Safety Information........................................1
2.Specification............................................................. .1
3.Package Content ........................................................2
4.Panel Control Function ...................................... .. 2
And
5.Setup Guide ...............................................................3
1.Important Safety Information
To prevent fire or shock hazard, do not expose this product to rain and moisture. For example: do not use near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or nearby a swimming pool. To avoid electric shock, do not take apart this product, provided as an accessory. This product should be operated only under power supply. Do not overload wall outlets and extension outlets as this can result in the risk of fire or electric shock.
NOTE:
This equipment has been tested and found to comply with the limits regulated by FCC and CE. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. The change or modifications no expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user's authority to operate the device.
2.Specification
Input Voltage DC 8~28V Current Consumption < 200mA
Operation temperature & humidity 0 40 less than 85% Storage temperature & humidity -20 ~+70 less than 90%
Weatherproof IP65 Output power @EIRP 20 dBm Channel selection Dip switch(8CH)
℃~+
℃℃
1
3.Package Contents
Check to make sure that all units shown as below are enclosed. If something missing, please contact your dealer.
1.5.8GHzCMOSCameraX1
3.Power Adapters (12V/300mA)
2.Package Contents4.Panel Control and Function
2. Cover X1,Screw X 2
4. Bracket X1
5.8GHz COMS Camera
1
2
3
5
4
1 DIP-Switch for channel selection.
DC power jack, connect to power supply. (8~28VDC).2 3 5.8GHz antenna. 4 Power indicator (red). 5 Lens.
2
2.Package Contents
1 2 3
5.Setup Guide
+
Fig. 1
1 According to the diagram, Connect the DC plug of the power
adapter to the DC jack, and connect the power adapter to an outlet(As shown in Fig.1).
2 DIP-Switch for Channel Selection, to find optimal reception,
the transmitter and receiver must to be configured as the same channel(As shown in Fig.2).
ON
UPPER
123
CH1
CH2
CH3
CH4
Down
Upper
Down
Upper Upper
Down Down
Down Down
Upper
Down
Down
Fig. 2
3
CH5
CH6
CH7
CH8
Down
Upper
Down
Upper Upper
Down
Down
Upper
Upper
Upper
Upper
Upper
3 Switch to the optimal channel before put on waterproof cover
and fasten the screw. (As shown in Fig 3)
Waterproof cover
Fig. 3
Screw
4
Preliminary Specification
For
VSC-5882
5.8GHz Wireless Outdoor CMOS Camera
Document Number:PSC08002 Page
Revision Date
TRANWO Technology Corp.
www.chemlink.com.tw
: : :
1of4 1A 2008-10-31
1
1. Introduction
This document describes the specifications and features of the CHEMLINK 5.8GHz Wireless outdoor CMOS Camera which use FM modulation technology for wireless A/V transmission.
2. Features
Avoids interference from crowded 2.4GHz ISM applications such as video
senders, 802.11b WLAN equipment, Bluetooth-enable products, cordless phones, microwave ovens, etc.
Operating frequency: 5733 ~ 5866MHz (8 channels)Up to 300 feet range, clear line of sightSupports NTSC / PAL composite Video formatAuto white balance control50Hz / 60Hz flicker cancellationIP65 weatherproof supported
3. Specifications
3.1 Wireless CMOS Camera
3.1.1 General specifications
Input voltage DC 8 ~ 28V Current consumption:
IR LEDs OFF 120mA @12VDC IR LEDs ON 200mA @12VDC Operating temperature & humidity 0℃ ~ +40℃ less than 85% Storage temperature & humidity -20℃ ~ +70℃ less than 90% Weatherproof IP65
3.1.2 Electrical specifications
RF
Output power @ EIRP FCC 0 dBm CE 14 dBm Modulation type FM Channel Frequency CH1 5733 MHz
Channel selection DIP switch Frequency stability Output flatness 3 dB
CH2 5752 MHz CH3 5771 MHz CH4 5790 MHz CH5 5809 MHz CH6 5828 MHz CH7 5847 MHz CH8 5866 MHz
250KHz
±
2
Video
Image
Illumination
LENS
Accessory
Input Level 1V
p-p
0.15 V
±
p-p
Load Impedance 75 ohms Pre-Emphasis NTSC & PAL
Sensor 1/3” CMOS Sensor Image area 5.961mm*4.276mm Array size 510 X 496 (NTSC)
628 X 586 (PAL)
Night Vision Range 10 m
LENS f6.0mm, F2.0 ,
(4 glasses with IR cut filter) LENS focus Fixed View angle 60
°
Adaptor DC 12V/300mA Bracket Optional
3.2 Dip Switch for Channel Selection
Upper
Down
CH1 Down Down Down
CH2 Upper Down Down
CH3 Down Upper Down
CH4 Upper Upper Down
CH5 Down Down Upper
CH6 Upper Down Upper
CH7 Down Upper Upper
CH8 Upper Upper Upper
3
4. Photograph
4.1 Wireless CMOS Camera
4
Loading...