2.4 GHz Digital Wireless
USB Camera
User's Manual
Preliminary Version 2.3
Contents
1 Package Content
2 Product Layout
USB Receiver
Camera
3 PC System Requirements
4 Camera Setup
4.1 Power Supply
4.2 Fine Tuning
4.3 Night Light / Night Vision
5 Receiver Setup
5.1 Windows Detect & Install New Device
5.2 Driver Installation
5.3 Skype Resident Program Installation
5.4 Monitoring Software
5.5 Pairing
6 Details on the Skype Resident Program Installation
7 Troubleshooting
8 Care and Maintenance
9 Specifications
2.4 GHz Digital Wireless USB Camera
ENGLISH
1
1
3
4
5
6
7
8
2
MIC
Light
9
10
11
1
2
3
4
1. Package Content
One Camera One USB Receiver One Power Adapter CD-ROM
This User's Manual
2. Product Layout
USB Receiver
1. Antenna
2. Camera indicator LEDs
3. Camera switch
/ Pairing button*
4. USB plug
Note: For Pairing, see
section 5.5
Camera
1. Antenna
2. Power indicator LED
3. Infrared LEDs
4. Lens
5. Supporting stand
6. Night-light / IR control
/ pairing button
7. Night-light
8. Microphone
9. Battery compartment
10. Power ON / OFF switch
11. Power adapter socket
3. PC System Requirements
Windows XP(SP2 or higher) or Windows Vista
Skype 3.0 or higher
R R
R
2
Pentium-IV 1.6GHz or higher (recommended)
256 MB RAM of system memory or higher (recommended)
One available USB port (preferably USB2.0)
Graphics Card (Must support DirectX 9.0c)
Sound Card (AC97 compatible sound card)
1GB Free HD Space
CD-ROM Drive (For software installation)
4. Camera Setup
4.1 Power Supply
The camera uses either 4 AAA-Size batteries (alkaline battery recommended)
or the household AC power current.
Loading the Batteries
1.
2. Open the battery compartment cover.
3. Insert 4 AAA-size batteries (follow the
plus (+) and minus (-) signs inside the
battery compartment).
4. Close the battery compartment cover,
and make sure it is locked securely.
Note 1: Do not mix old batteries with new
ones.
Note 2: Remove the batteries from the camera if you do not plan to use
it for a prolonged period of time.
5. Slide the POWER switch to the ON position. The LED on the camera
will light up (red light).
Note : When battery power is sufficient, the light is constantly red ;
.
Loosen the screw on the bottom of the camera by using a screw driver.
when
the battery is low, the LED light will start blinking
3
4
22
11
ENGLISH
3
ON
OFF
2
1
3
Using AC Power
1. Plug one end of the provided power
adapter into a wall outlet and the other
end into the bottom of the camera.
Note: Use the adapter labeled
OUTPUT: 6V DC with the
camera.
2. Slide the ON/OFF switch to the ON
position. The LED on the camera will
light up (red light).
4.2 Fine Tuning
Place the camera in a convenient location,
point the lens towards the observation
area and adjust the angle by rotating the
lens head.
4.3 Night Light / Night Vision
Press the night light button, the night light LEDs will remain ON.
The camera has nine high-intensity infrared
LEDs for picking up clear images in unlit
locations.
Note: Press the night light button, the
image changes automatically into
the night vision mode.
5. Receiver Setup
There are 2 CD disks in the package, Disk 1: USB driver software / Skype
resident program software, Disk 2: AP monitoring software.
Please follow the steps below to setup USB receiver.
Light
M
IC
Lig
ht
ENGLISH
Loading...