Transition Networks TN-GLC-xx-xx, TN-GLC-BX-U, TN-GLC-LH-SM, TN-CWDM-SFP-1xx0, TN-GLC-SX-MM User Manual

...
User’s Guide
TN-GLC-xx-xx and TN-CWDM-SFP-1xx0 Cisco CompatibleSmall Form Factor Pluggable (SFP)
TN-GLC-T
modules are designed to install in any SFP port, allowing for1000Base-T, 1000Base-SX or 1000Base-LX interfaces to the network through the SFP connector. The TN-GLC-xxx and TN-CWDM-SFP-1xx0 transceivers are designed for bi-directional serial-optical data communications such as Gigabit Ethernet or fiber channel at speeds up to 2.125 Gbps.
Transceiver Modules**
The Transition Networks TN-GLC-xx-xx and TN-CWDM­SFP-1xx0 series small form factor pluggable (SFP) transceiver
TN-GLC-SX-MM
Part Number Port Description
TN-GLC-T
TN-GLC-SX-MM
TN-GLC-SX-MM-2K
TN-GLC-LH-SM
TN-GLC-BX-U
TN-GLC-BX-D
*Unless otherwise indicated, the distances listed are the typical maximum cable distance. The actual maximum cable distances are dependent upon the physical characteristics of the network installation.
**Transition Networks' SFP modules fully comply with the Multi-Sourcing Agreement (MSA). This compliance allows our SFP modules to be used in other MSA compliant SFP platforms without problems. In addition, TN SFP modules specified in this manual are also compatible with all Cisco SFP-based routers and switches, as well as its IOS software. TN SFP modules ARE NOT modules.
Cisco OEM brand
TN-CWDM-SFP-1xx0
1000Base-T , RJ-45 100m (328 ft)*
1000Base-SX, duplex LC, 850 nm, 220 m (722 ft)* on 62.5/125 µm fiber 550 m (1840 ft)* on 50/125 µm fiber 1000Base-SX, duplex LC 1300 nm, extended multimode up to 2 km (1.2 miles)*
1000Base-LX, 1310 nm, single mode 10 km (6.2 miles)*
1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx nm, single mode, single fiber 10 km (6.2 miles)*
1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx nm, single mode, single fiber 10 km (6.2 miles)*
Installation . . . . . . . . . . . . . . . . . . . . . . . . .3
Cable Specifications . . . . . . . . . . . . . . . . .5
Technical Specifications . . . . . . . . . . . . . .8
Contact Us . . . . . . . . . . . . . . . . . . . . . . . . .9
Compliance Information . . . . . . . . . . . . .11
TN-GLC-BX-0
TN-GLC-xx-xx SFPs
.)
Part Number Port Description
TN-GLC-BX-U
TN-GLC-BX-D
TN-GLC-BX-U-40
TN-GLC-BX-D-40
TN-GLC-BX-U-60
TN-GLC-BX-D-60
TN-GLC-FE-100BX-U
TN-GLC-FE-100BX-D
TN-GLC-FE-100FX
TN-GLC-FE-100LX
TN-GLC-GE-100FX***
TN-GLC-ZX-SM
TN-CWDM-SFP-1xx0
1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx, single mode, single fiber 10 km (6.2 miles)*
1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx, single mode, single fiber 10 km (6.2 miles)*
1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx, single mode, single fiber 40 km (24.9 miles)*
1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx, single mode, single fiber 40 km (24.9 miles)*
1000Base-BX, Simplex LC 1310 nm Tx/1490 nm Rx, single mode, single fiber 60 km (37.3 miles)*
1000Base-BX, Simplex LC 1490 nm Tx/1310 nm Rx, single mode, single fiber 60 km (37.3 miles)*
100Base-BX, Simplex LC 1310 nm Tx/1550 nm Rx, single mode, single fiber 20 km (12.4 miles)*
100Base-BX, Simplex LC 1550 nm Tx/1310 nm Rx , single mode, single fiber 20 km (12.4 miles)*
100Base-BX, Duplex LC 1300 nm, multimode 2 km (1.2 miles)*
100Base-BX, Duplex LC 1310 nm, single mode 20 km (12.4 miles)*
100Base-BX, Duplex LC 1300 nm, multimode 2 km (1.2 miles)*
1000Base-LX, 1550 nm, single mode 80 km (49.7 miles)*
1000Base-LX, single mode 80 km (49.7 miles)*
***Provide 100Base-FX interface when plugged into a gigabit SFP slot on Cisco catalyst 3750, 3560, and 2970 series switches.
Note: Install simplex or single fiber SFP models in pairs in the same network where
one is the local SFP and the other is the remote SFP.
Installation
Installing the SFP transceiver
To install the SFP module into a network switches media converter, do the following:
1. Position the module at the installation slot so that the label faces up.
2. Carefully slide the module into the installation slot, aligning it with the internal installation guides.
Installing copper cables
1. Locate or build 1000Base-T compliant copper cables with male, RJ-45 connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on the media converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45 port on the other device.
xx = center wavelength (λc) (See technical specifications for more details.)
27 =1270nm 39 = 1390nm 53 = 1530nm
29 = 1290nm 41 = 1410nm 55 = 1550nm
31 = 1310nm 43 = 1430nm 57 = 1570nm
33 = 1330nm 47 = 1470nm 59 = 1590nm
35 = 1350nm 49 = 1490nm 61 = 1610nm
37 = 1370nm 51 = 1510nm
*Unless otherwise indicated, the distances listed are the typical maximum cable distance. The actual maximum cable distances are dependent upon the physical characteristics of the network installation.
**Transition Networks' SFP modules fully comply with the Multi-Sourcing Agreement (MSA). This compliance allows our SFP modules to be used in other MSA compliant SFP platforms without problems. In addition, TN SFP modules are also compatible with all Cisco SFP-based routers and switches, as well as its IOS software. TN SFP modules ARE NOT
2
Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600—24 hours
Cisco OEM brand modules.
RJ-45 port
on the media
converter
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
RJ-45 port
on the other device
(switch, work station, etc
3
TN-GLC-xx-xx SFPs
T
T
Installing the fiber cables
1. Locate or build 1000Base-SX-compliant or 1000Base-LX-compliant fiber cable with male TX to RX connectors installed at both ends.
2. Install the fiber cable as shown below.
Connect fiber cable to media converter as shown.
RX TX
Connect fiber cable
to other device
(media converter,
hub, etc.) as shown
RX TX
Cable Specification
Copper cable (Category 5 -- minimum requirement)
Gauge = 24 to 22 AWG; Attenuation = 22.0 dB /100m @ 100 MHz
• Straight-through OR crossover cable may be used.
• Shielded twisted-pair (STP) OR unshielded twisted-pair (UTP) may be used
• All pin pairs (1&2, 3&6, 4&5, 7&8) are active in a gigabit network.
• Use only dedicated wire pairs for the active pins; e.g., blue/white & white/blue,
orange/white & white/orange, etc.
• Do not use flat or silver satin wire.
wisted Pair #1
wisted Pair #2
Straight-Through Cable
1 2
3 6
1 2
3 6
Twisted Pair #1
Twisted Pair #2
Crossover Cable
1 2
3 6
1 2
3 6
Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)
4
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
5
TN-GLC-xx-xx SFPs
Fiber cable
The physical characteristics must meet or exceed IEEE 802.3zspecifications.
Singlemode fiber (recommended): 9 µm Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140, 85/140, 50/125 µm
TN-GLC-SX-MM 850 nm multimode Fiber Optic Transmitter Power: min: -9.5 dBm max: -3.5 dBm Fiber Optic Receiver Sensitivity: min: -18.0 dBm max: -1.0 dBm Link Budget: 8.5 dB
TN-GLC-SX-MM-2k 1300 nm multimode Fiber Optic Transmitter Power: min: -9.0 dBm max: -1.0dBm Fiber Optic Receiver Sensitivity: min: -19.0 dBm max: -1.0 dBm Link Budget: 18.0 dB
TN-GLC-LH-SM 1310 nm singlemode Fiber Optic Transmitter Power: min: -9.5 dBm max: -3.0 dBm Fiber Optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm Link Budget: 10.5 dB
TN-GLC-BX-U 1310 nm Tx/1490 nm Rx single mode TN-GLC-BX-D 1490 nm Tx/1310 nm Rx single mode Fiber Optic Transmitter Power: min: -9.0 dBm max: -1.0 dBm Fiber Optic Receiver Sensitivity: min: -21.0 dBm max: -1.0 dBm Link Budget: 12.0 dB
TN-GLC-BX-U-40 1310 nm Tx/1490 nm Rx single mode TN-GLC-BX-D-40 1490 nm Tx/1310 nm Rx single mode Fiber Optic Transmitter Power: min: -3.0 dBm max: +2.0 dBm Fiber Optic Receiver Sensitivity: min: -23.0 dBm max: -1.0 dBm Link Budget: 20.0 dB
TN-GLC-BX-U-60 1310 nm Tx/1490 nm Rx single mode TN-GLC-BX-D-60 1490 nm Tx/1310 nm Rx single mode Fiber Optic Transmitter Power: min: -2.0 dBm max: +4.0 dBm Fiber Optic Receiver Sensitivity: min: -25.0 dBm max: -1.0 dBm Link Budget: 23.0 dB
Fiber cable -- continued
TN-GLC-FE-100FX 1300 nm multimode TN-GLC-GE-100FX 1300 nm multimode Fiber Optic Transmitter Power: min: -23.5 dBm max: -14.0 dBm Fiber Optic Receiver Sensitivity: min: -32.0 dBm max: -8.0 dBm Link Budget: 8.5 dB
TN-GLC-FE-100LX 1310 nm single mode Fiber Optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -0.0 dBm Link Budget: 19.0 dB
TN-GLC-ZX-SM 1550 nm single mode Fiber Optic Transmitter Power: min: 0.0 dBm max: +5.0 dBm Fiber Optic Receiver Sensitivity: min: -24.0 dBm max: -3.0 dBm Link Budget: 24 dB
TN-CWDM-SFP-1xx0 1270nm -1610nm single mode Fiber Optic Transmitter Power: min: 0.0 dBm max: +5.0 dBm Fiber Optic Receiver Sensitivity: min: -25.0 dBm max: -3.0 dBm Link Budget: 25 dB
For the most up-to-date information on the TN-GLC-xx-xx transceiver module, view the user’s guide on-line at: www.transition.com.
Product is certified by the manufacturer to comply with DHHS Rule 21/CFR, Subchapter J applicable at the date of manufacture.
WARNING: or view directly with optical instruments. Failure to observe this warning could result damage to your eyes or blindness.
WARNING: those specified herein could result in hazardous radiation exposure.
The fiber optic transmitters on this device meet Class I Laser safety requirements per IEC-825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.
Visible and invisible laser radiation when open. Do not stare into beam
Use of controls, adjustments or the performance of procedures other than
TN-GLC-FE-100BX-U 1310 nm Tx/1550 nm Rx single mode TN-GLC-FE-100BX-D 1550 nm Tx/1310 nm Rx single mode Fiber Optic Transmitter Power: min: -14.0 dBm max: -8.0 dBm Fiber Optic Receiver Sensitivity: min: -32.0 dBm max: -0.0 dBm Link Budget: 18.0 dB
Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)
6
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
7
TN-GLC-xx-xx SFPs
Technical Specification
For use with Transition Networks Model TN-GLC-xxx or equivalent.
Standard: IEEE 802.3 2003; ANSI X3.297-1997
TN-GLC-FE-xxx IEEE 802.3 100Base-Fx; IEEE802.3ah 100Base-Bx; Intermediate - Reach Sonet OC-3/SDH STM-1 (s-1-1)
TN-GLC-xx-xx and TN-CWDM-SFP-1xx0 modules:
Compliant with IEEE 802.3z Gigabit Ethernet; FC-1x/2x SM-LC-L FC-PI.
TN-GLC-T modules: Compliant with IEEE 802.32 Gigabit Ethernet (1000Base-T)
Output wavelength -6.0 <
Dimensions: 0.52 x 2.18 x 0.33’’ (13.4 x 55.5 x 8.5 mm, Fiber)
Weight: 1 oz. (28 g) approximately
Power: 3.3V, Fiber 0.66 W; Copper 1.0 W
Operating Temp: 0°C to 70°C (32°F to 158° F )
Storage Temp: -40°C to 85°C (-40° to 185°F)
Humidity: 5% to 95%, non-condensing
Altitude: 0 to 10,000 feet
Warranty: Lifetime
Note: Transition Networks' SFP modules fully comply with the Multi-Sourcing
Agreement (MSA). This compliance allows our SFP modules to be used in other MSA compliant SFP platforms without problems. In addition, TN SFP modules are also compatible with all Cisco SFP-based routers and switches, as well as its IOS software and SMARTnet. TN SFP modules ARE NOT OEM brand modules.
λc < +7.5 nm
0.95 x 2.8 x 0.54” (14-0 x 71.1 13.7 mm, Copper)
and TN-GLC-GE-xxx: Compiant with
Contact Us
Technical support
Technical support is available 24 hours a day. U.S.A. and Canada: 1-800-260-1312 International: 00-1-952-941-7600
Transition now
Chat live via the Web with Transition Networks Technical Support. Log onto www.transition.com and click the Transition Now link.
Web-Based seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
techsupport@transition.com
Address
Transition Networks 10900 Red Circle Drive Minnetonka, MN 55343, U.S.A. telephone: 952-941-7600 toll free: 800-526-9267 fax: 952-941-2322
Cisco
Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)
8
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
9
TN-GLC-xx-xx SFPs
Declaration of Conformity
Name of Mfg: Transition Networks
Model: TN-GLC-xx-xx Series Transceiver Modules Part Number(s): TN-GLC-T, TN-GLC-SX-MM, N-GLC-SX-MM-2k,
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the TN-GLC-xxx to which this declaration refers
IEC 60825-1; IEC60825-2; FC1X/2X SM-LC-L FC-PI; IEEE 802.3z 2003; ANSI X3.297
1997; Class A; FDA 21; CFR1040.10; CFR1040.11
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
Stephen Anderson, Vice-President of Engineering Date
10900 Red Circle Drive, Minnetonka MN 55343 U.S.A.
TN-GLC-LH-SM, TN-GLC-BX-U, TN-GLC-BX-D, TN-GLC-BX-U-40, TN-GLC-BX-D-40, TN-GLC-BX-U-60, TN-GLC-BX-D-60, TN-GLC-FE-100BX-U, TN-GLC-FE-100BX-D, TN-GLC-FE-100FX, TN-GLC-FE-100LX, TN-GLC-GE-100LX, TN-GLC-ZX-SM, TN-CWDM-SFP-1xx0
is in conformity with the following standards:
October 2008____
Compliance Information
CE Mark: IEC-60825; FDA 21; CFR 1040.10 and 1040.11
FCC regulations
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user's own expense.
Canadian regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications. Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
European regulations Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Achtung !
Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für Gegenmaßnahmen verantwortlich.
Attention !
Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures spécifiques appropriées.
Tech Support: 1-800-260-1312 -- International: 00-1-952-941-7600 -- (24 hours)
10
In accordance with European Union Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003, Transition Networks will accept post usage returns of this product for proper disposal. The contact information for this activity can be found in the 'Contact Us' portion of this document.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG­Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
techsupport@transition.com -- Click the Transition Now link for a live Web chat.
11
TN-GLC-xx-xx SFPs
Trademark notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright restrictions © 2004 Transition Networks. All rights reserved. No part of this work may be reproduced or used in any form or means (graphic, electronic, mechanical) without written permission from Transition Networks.
12
Printed in the U.S.A.
33389.D
Loading...