User’s Guide
CPSMC0200-2x0
Dual-Slot PointSystem™ Chassis
The Transition Networks
CPSMC0200-2x0 series dual-slot
PointSystem™ chassis is designed for
installation of one or two selectable
Transition Networks PointSystem™
media converter slide-in-modules.
Installation . . . . . . . . . . . . . . . . . .2
Technical Specifications . . . . . . . .4
Troubleshooting . . . . . . . . . . . . . .5
Compliance Information . . . . . . . .6
Contact Us . . . . . . . . . . . . . . . . . .7
Part Number Description
CPSMC0200-200 Dual-Slot PointSystem™ chassis intended for installation of
any PointSystem™ media converter slide-in-modules.
CPSMC0200-210 Dual-Slot PointSystem™ chassis intended for installation of
any PointSystem™ media converter slide-in-modules. Also
provides a Last Gasp trap generation.
Optional Accessories (sold separately)
Part Number Description
SPS-1872-SA Optional External Power Supply; 18-72VDC Stand-Alone
Output: 12.6VDC, 1.0 A
WMBP Optional Wall Mount Bracket; Length: 5.0 in. (127 mm)
WMBV Optional Vertical Mount Bracket; 5.0 in. (127 mm)
WMBD Optional DIN Rail Mount Bracket; 5.0 in. (127 mm)
2
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
CPSMC0200-200 / CPSMC0200-210
Installation
Installing a Slide-in-Module
CAUTION: Do NOT install Two (2) PointSystem™ media converter slide-inmodules whose total power requirements exceed 12 W (with a maximum of
6 W per slot). Failure to observe this caution could cause data transfer to fail
and also could result in damage to, and subsequent failure of, the media
converter slide-in-module.
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when installing the media converter slide-in-module in to the
dual-slot chassis. Failure to observe this caution could result in damage to,
and subsequent failure of, the media converter slide-in-module.
NOTE: If only one slide-in-module is to be installed into the dual-slot chassis,
ensure network standards compliance by obtaining a custom faceplate (P/N
CPSFP-200) from Transition Networks for installation into the second, unused
slot.
To install a slide-in-module into the dual-slot chassis:
1. Refer to the user’s guide that comes with the slide-in-module to ensure
that any switches or jumpers on the slide-in-module circuit board are set
correctly for the site installation.
2. Carefully align the slide-in-module with the chassis installation guides
and slide the module into the installation slot.
3. Ensure that the slide-in-module is firmly seated inside the chassis.
4. Push in and rotate the attached panel faster screw clockwise to secure the
slide-in-module to the chassis front.
5. Repeat steps 1-4 for the second slide-in-module.
100BASE-TX
PWR
RXF
RXC
LKF
100BASE-TX
LKC
RX
TX
100BASE-FX
Panel Fastener Screw
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
3
Installation -- Continued
Power the Chassis
To supply AC power to the dual-slot chassis:
1. Locate an appropriate 12 volt power adapter for the installed media
converter slide-in-module(s).
2. Connect the barrel connector on the power adapter to the dual-slot
chassis power port (located on the back of the chassis).
3. Connect the power adapter plug to AC power.
4. Verify that the dual-slot chassis is powered by observing the illuminated
LED(s) on the installed slide-in-module(s).
To supply DC power to the dual-slot chassis:
Consult the user’s guide for the Transition Networks SPS1872-xx DC external
power supply for powering the dual-slot chassis.
Last Gasp Option
(CPSMC0200-210 model only)
The CPSMC0200-210 model features the Last Gasp option, which enables the
device to send out an SNMP trap to the device in the event of a power failure;
alerting the management console that the device has failed.
4
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
CPSMC0200-200 / CPSMC0200-210
Installation -- Continued
Grounding the Media Converter
The dual-slot chassis comes equipped with grounding lugs located on the
back panel. They require a grounding conductor wire terminated with a two-
hole, compression-type, grounding connector. The grounding wire -- which
must be a copper conductor -- is not included with the chassis and must be
provided by the customer/installer.
The electrical conducting path from the single-slot chassis must:
• Flow via the grounding lugs to the common bonding network (CBN) for
telecom installations, or to an alternative approved grounding system (if
required) for non-telecom installations.
• Be of sufficiently low impedance to conduct fault currents likely to be
imposed on the media converter, and
• Enable proper operation of any over-current protection devices.
The conductor must be fastened to the grounding lugs with the enclosed antirotation star-washers and lug-nut fasteners. The applied torque required to the
connector lug-nut fasteners is specified by the connector’s manufacturer.
To properly ground the dual-slot chassis:
1. Obtain one (1) grounding conductor (12 AWG copper wire gauge or
larger) with a two-hole, compression-type, grounding connector.
2. Attach the grounding conductor to the converter by placing the two-hole
connector onto the grounding lugs and fasten with the enclosed lockwashers / lug-nuts at the proper torque (per the manufacturer’s
specification).
3. Attach the opposite end of the
grounding conductor to the
common bonding network
(CBN) for telecom, or to earth
ground (if required) for nontelecom installations.
grounding
lugs
grounding
connector
and wire
earth ground
3/4-inch
spacin
g
Grounding lugs
(6-32, 1/8" diam.)
12 AWG copper wir
e
(not included)
Star washer (included)
Lug nuts (included)
Two-hole, compression-type
grounding connector
(not included)
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
5
Technical Specifications
For use with Transition Networks Model CPSMC0200-2x0 or equivalent.
NOTE: The CPSMC0200-2x0 dual-slot chassis is Class B compliant ONLY if
Class B-compliant media converters are installed. Installation of a Class Acompliant media converter reduces the chassis to Class A compliance.
The maximum power delivery capacity for each chassis slot is 12 Watts with an
aggregate chassis maximum of 6 Watts per slot. Example: A 9-Watt media
converter would require the power of both slots. In this example, the second slot
must remain unused.
Compliance EN55022; Class A&B; CE Mark
Dimensions 5.4 x 5.6 x 2.2 in (137 x 142 x 56 mm)
Weight 1.4 lb. (0.6 kg.) (approximate)
MTBF
(CPSMC0200-200) 48,501 hours (MIL217F2 V5.0) (MIL-HDBK-217F)
128,553 hours (Bellcore7 V5.0)
MTBF
(CPSMC0200-210) 1,618,162 hours (MIL217F2 V5.0) (MIL-HDBK-217F)
3,259,373 hours (Bellcore7 V5.0)
Power Supply 12VDC, 1.25 A; 100-240 VAC
Environment Tmra*: 0 to 60°C (32 to 140° F )
Storage Temp: -20 to 85°C
Humidity: 10 to 90%, non condensing
Altitude: 0 to 10,000 feet
Warranty Lifetime
*Manufacturer’s rated ambient temperature for the dual-slot chassis. Refer to the
user’s guide of the installed media converter for its operating temperature range.
The information in this user’s guide is subject to change. For the most up-to-date
information on the CPSMC0100-20x dual-slot chassis, view the user’s guide online at: www.transition.com.
6
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
CPSMC0200-200 / CPSMC0200-210
Troubleshooting
1. Is a media converter installed in the dual-slot chassis?
NO
• Install a slide-in-module media converter into the dual-slot chassis.
See page 2 for installation instructions.
• Proceed to step 2.
YES
• Proceed to step 2.
2. Is the power LED on the installed media converter illuminated?
NO
• Is the power adapter the proper type of voltage and cycle frequency
for the AC outlet? (See “Power Supply” on page 5.)
• Is the power adapter properly installed in the media converter and in
the grounded AC outlet?
• Contact Technical Support: US/Canada: 1-800-260-1312,
International: 00-1-952-941-7600.
YES
• Proceed to step 3.
3. Are two media converters installed in the dual-slot chassis?
YES
• The dual-slot chassis can accommodate two media converters if the
total power requirement is 12 W or less (with a maximum of 6 W per
slot). If the converters exceed this limit, remove one of the
converters.
• Contact Technical Support: US/Canada: 1-800-260-1312,
International: 00-1-952-941-7600.
NO
• Contact Technical Support: US/Canada: 1-800-260-1312,
International: 00-1-952-941-7600.
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
7
Declaration of Conformity
Name of Mfg: Transition Networks
6475 City West Parkway, Minneapolis MN 55344 USA
Model: CPSMC0200-2x0 Series Dual-Slot PointSystem™ Chassis
Part Number: CPSMC0200-200, CPSMC0200-210
Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the CPSMC0200-2x0 to which this declaration refers is in
conformity with the following standards.
EN 55022:1998 Class A & B; FCC Part 15 Subpart B
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
June 8, 2001
Stephen Anderson, Vice-President of Engineering Date
Contact Us
Technical Support
Technical support is available 24 hours a day.
United States: 800-260-1312
International: 952-941-7600
Transition Now
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Web-Based Seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
techsupport@transition.com
Address
Transition Networks
6475 City West Parkway
Minneapolis, MN 55344, USA
telephone: 952-941-7600
toll free: 800-526-9267
fax: 952-941-2322
8
Trademark Notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright Restrictions
© 2001-2004 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any
means – graphic, electronic, or mechanical – without written permission from Transition
Networks.
Printed in the U.S.A.
33211.E
Compliance Information
CISPR/EN55022 Class A & B
CE Mark
FCC Regulations
This equipment has been tested and found to comply with the limits for a Class A & B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference. In which case, the user will be required to correct the
interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A & B limits for radio noise for digital
apparatus set out on the radio interference regulations of the Canadian Department of
Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la Class A & B prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des Communications du Canada.
Loading...