Transition Networks CETTF1014-105, CETTF1011-105, CETTF1014-106, CETTF1015-105, CETTF1018-105 User Manual
...
User’s Guide
CETTF10xx-105
Slide-in-Module Media Converter
• Ethernet
• Copper to Fiber
• 10Base-T to 10Base-FL
Transition Networks CETTF10xx-105 series Ethernet
10Base-T to 10Base-FL media converters (designed
to be installed in a PointSystem™ chassis) connect
10Base-T twisted-pair copper cable to multimode or
single mode 10Base-FL fiber-optic cable.
* CETTF1029-105 and CETTF1029-106 are designed to be installed in the same
network where one is the local converter and the other is the remote converter.
The distances listed are the typical maximum cable distance. Actual distance is
dependent upon the physical characteristics of the network installation.
Part Number Port One - Copper
10Base-T
Port Two - Fiber-Optic
10Base-FL
CETTF1011-105 RJ-45
100 m (328 ft)*
ST, 850 nm multimode, duplex
2 km (1.2 miles)
CETTF1012-105 RJ-45
100 m (328 ft)*
ST, 1310 nm single mode, duplex
20 km (12.4 miles)
CETTF1013-105 RJ-45
100 m (328 ft)*
SC, 850 nm multimode, duplex
2 km (1.2 miles)
CETTF1014-105 RJ-45
100 m (328 ft)*
SC, 1310 nm single mode, duplex
20 km (12.4 miles)
CETTF1022-105 RJ-45
100 m (328 ft)*
ST, 1310 nm single mode, duplex
40 km (24.9 miles)
CETTF1027-105 RJ-45
100 m (328 ft)*
ST, 1300 nm multimode, duplex
5 km (3.1 miles)
CETTF1018-105 RJ-45
100 m (328 ft)*
MT-RJ, 850 nm multimode, duplex
2 km (1.2 miles)
CETTF1014-106 RJ-45
100 m (328 ft)*
SC, 1310 nm single mode, duplex
20 km (12.4 miles)
CETTF1015-105 RJ-45
100 m (328 ft)*
SC, 1310 nm single mode, duplex
40 km (24.9 miles)
CETTF1029-105* RJ-45
100 m (328 ft)*
SC, 1310 nm (TX) / 1550 nm (RX)
single fiber, 20 km (12.4 miles)
CETTF1029-106* RJ-45
100 m (328 ft)*
SC, 1550 nm (TX) / 1310 nm (RX)
single fiber, 20 km (12.4 miles)
Installation
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting the 4-position switch and the jumper and when
installing the media converter. Failure to observe this caution could result in
damage to, and subsequent failure of, the media converter.
Set the 4-Position Switch
• The 4-position switch is
located on the media
converter circuit board.
• Use a small flat-blade
screwdriver to set the
switches (see the drawing).
NOTE: When the fiber port or the copper port is disabled (switches 1 and 2),
network traffic coming into the media converter is ignored and no traffic flows
out. In this mode, the media converter is disconnected from the network.
1. Fiber Port (10Base-FL)
Up Enable network traffic on the fiber port.
Down Disable network traffic on the fiber port.
2. Copper Port (10Base-T)
Up Enable network traffic on the copper port.
Down Disable network traffic on the copper port.
3. AutoCross
Up Enable AutoCross (see page 6).
Down Disable AutoCross.
(When AutoCross is disabled, the 10Base-T (copper) port is in
MDI-X (crossover) mode.)
4. Link Pass-Through
Up Enable Link Pass-Through (see page 6).
Down Disable Link Pass-Through.
(When Link Pass-Through is disabled, remote faults are not passed
along to any downstream equipment.)
Set the Hardware/Software Jumper
The hardware/software jumper is located on the media converter circuit
board. Use small needle-nosed pliers or a similar device to set the jumper.
Hardware The media converter mode is determined
by the 4-position switch settings.
Software The media converter mode is determined
by the most-recently saved, on-board
microprocessor settings.
CETTF10xx-105
2
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Software Mode
Hardware Mode
H
S
H
S
Fiber Port; up = Enable
Copper Port; up = Enable
Link Pass Through;
up = Enable
AutoCross; up = Enable
1234
3
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
Installation -- Continued
Install the Slide-in-Module
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when installing the CETTF10xx-105 slide-in-module media
converter. Failure to observe this caution could result in damage to, and
subsequent failure of, the media converter.
1. Carefully slide the slide-in-module into the installation slot, aligning the
module with the installation guides.
2. Ensure that the module is firmly seated inside the chassis.
3. Push in and rotate the attached panel fastener screw clockwise to secure
the module to the chassis front.
Connect the Twisted-Pair Copper Cable
NOTE: The AutoCross feature allows either MDI (straight-through) or MDI-X
(crossover) cable connections to be configured automatically, according to the
network conditions.
1. Locate or build 10Base-T copper cables with male, RJ-45 connectors
installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on
the CETTF10xx-105 media converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45
port on the other device (switch, workstation, etc.).
CFMFF100
CFMFF100
CETCF100
CFETF100
CFETF110
CFMFF100
SPD
PWR
FRX
CRX
FLNK
CLNK
10/100TX
RX
TX
10/100SX
100BASE-TX
RX
TX
100BASE-FX
Link Alert
E
D
0
50½
LA
PWR
RXF
RXC
COL
LKS
PWR
LKM
10BASE-2
10BASE-FL
LKS
PWR
LKM
LKS
PWR
LKM
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
I
0
TERM
INIT
RX
TX
LNK
PWR
CPSMM120
SERIAL
10BASE-T
R
E
S
E
T
I
0
RX
TX
Panel Fastener Screw
PWR
RXF
LKF
RXC
LKC
RJ-45 port
on the other device
(switch, work station, etc.)
RJ-45 port
on the media
converter
CETTF10xx-105
4
24-hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Installation -- Continued
Connect the fber cable
1. Locate or build IEEE 803.2™ compliant 10Base-FL fiber cable with male,
two-stranded TX to RX connectors installed at both ends.
2. Connect the fiber cables to the CETTF10xx-105 media converter as
described:
• Connect the male TX cable connector to the female TX port.
• Connect the male RX cable connector to the female RX port.
3. Connect the fiber cables to the other device (another media converter,
hub, etc.) as described:
• Connect the male TX cable connector to the female RX port.
• Connect the male RX cable connector to the female TX port.
Power the Media Converter
The slide-in-module media converter is powered through the Transition
Networks PointSystem™ chassis.
Connect the fiber cable
to the media converter
as shown.
Connect the fiber cable
to the other device
(media converter,
hub, etc.) as shown
RX
TX
RX
TX
5
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
Operation
Status LEDs
Use the status LEDs to monitor the media converter operation in the network
PWR (Pow
er) On = Connection to external AC power.
LKF (Link -
fiber) On = The fiber link is up.
Off = A lack of power or a broken fiber link.
LKC (Link -
copper) On = The copper link is up.
Off = A lack of power or a broken copper link.
RXF (Receive -
fiber) Flashing = Data reception on the fiber link.
RXC (Receive -
copper) Flashing = Data reception on the copper link.
SNMP
Use SNMP at an attached terminal or at a remote location to monitor the
media converter by monitoring:
• Media converter power.
• Copper link and fiber link status.
• Copper receive and fiber receive status.
• Hardware switch settings.
• Fault condition.
Also, use SNMP to enter network commands that:
• Enable/disable the copper port .
• Enable/disable the fiber port.
• Enable/disable AutoCross.
• Enable/disable Link Pass Through.
• Power down the media converter.
See the on-line documentation that comes with Transition Networks
FocalPoint™ software for applicable commands and usage at
www.transition.com.
RXC
LKF
PWR
LKC
RXF
Loading...