Transition Networks CBFTF1011-150, CBFTF1015-150, CBFTF1013-150, CBFTF1014-150, CBFTF1018-150 User Manual
...
* Typical maximum cable distance. (Actual distance is dependent upon the
physical characteristics of the network.) (TX) = transmit (RX) = receive
** SBFTF1029-
150 and SBFTF1029-151 are intended to be installed in the same
network where one is the local converter and the other is the remote
converter.
*** SBFTF1029-
152 and SBFTF1029-153
are intended to be installed in the same
network where one is the local
converter and the other is the remote
converter.
USER’S GUIDE
CBFTF10xx-15x
Slide-in-Module Media Converter
• Copper to Fiber
• 10/100 Bridging (2-Port)
• 10Base-T/100Base-TX to 100Base-FX
The CBFTF10xx-15x 2-port Ethernet/Fast Ethernet
bridging Media Converter is designed to be
installed in a Transition Networks PointSystem™
chassis and connects 10Base-T Ethernet or
100Base-TX Fast Ethernet twisted-pair copper
network devices to network devices on a 100BaseFX Fast Ethernet fiber network.
CBFTF1029-150** RJ-45
100 m (328 ft)*
SC, 1310 mn (TX)/1550 nm (RX)
singlemode, 20 km (12.4 miles)*
CBFTF1029-151** RJ-45
100 m (328 ft)*
SC, 1550 mn (TX)/1310 nm (RX)
singlemode, 20 km (12.4 miles)*
CBFTF1029-152*** RJ-45
100 m (328 ft)*
SC, 1310 mn (TX)/1550 nm (RX)
singlemode, 40 km (24.8 miles)*
CBFTF1029-153*** RJ-45
100 m (328 ft)*
SC, 1550 mn (TX)/1310 nm (RX)
singlemode, 40 km (24.8 miles)*
Part Number Port One - Copper
10Base-T/100Base-TX
Port Two - Duplex Fiber-Optic
100Base-FX
CBFTF1011-150 RJ-45
100 m (328 ft)*
ST, 1300 nm multimode
2 km (1.2 miles)*
CBFTF1013-150 RJ-45
100 m (328 ft)*
SC, 1300 nm multimode
2 km (1.2 miles)*
CBFTF1014-150 RJ-45
100 m (328 ft)*
SC, 1310 nm singlemode
20 km (12.4 miles)*
CBFTF1015-150 RJ-45
100 m (328 ft)*
SC, 1310 nm singlemode
40 km (24.8 miles)*
CBFTF1018-150 RJ-45
100 m (328 ft)*
MT-RJ, 1300 nm multimode
2 km (1.2 miles)*
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .5
Cable Specifications . . . . . . . . . . .8
Technical Specifications . . . . . . . .9
Fault Isolation and Correction . .10
Compliance Information . . . . . . .12
2
CBFTF10xx-15x
Tech Support: 800-260-1312 International: 952-941-7600 7am-6pm CST (GMT-6:00)
INSTALLATION
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting the 4-position switch and the jumper(s) and when
installing the Slide-in-Module. Failure to observe this caution could result in
damage to, and subsequent failure of, the Media Converter.
Set the 4-Position Switch
The 4-position switch is located on the
side of the Media Converter. Use a
small flatblade screwdriver or a similar
device to set the recessed switches.
Refer to the drawing for the locations
of the four individual switches.
1. Auto-Negotiation
UP Enables Auto-Negotiation on the copper port.
Advertises 100 Mb/s full-duplex and half duplex,
and 10 Mb/s full-duplex and half duplex.
DOWN Disables Auto-Negotiation on the copper port.
2. Copper Mode
(Applies only if switch 1 is DOWN.)
UP Forces full-duplex operation on the copper port.
DOWN Forces half-duplex operation on the copper port.
3. Speed
(Applies only if switch 1 is DOWN.)
UP Forces 100 Mb/s operation on the copper port.
DOWN Forces 10 Mb/s operation on the copper port.
4. Fiber Mode
UP Forces full-duplex operation on the fiber port.
DOWN Forces half-duplex operation on the fiber port.
Speed (UP=100Mb/s)
Copper Mode (UP=Full-Duplex)
Auto-Negotiation (UP=Enabled)
Fiber Mode
(UP=Full-Duplex)
1234
techsupport@transition.com -- Select the “Transition Now” Link for a Live Web Chat
3
INSTALLATION -- Continued
Set the Jumpers
The jumpers are located on the Media Converter circuit board. Use small
needle-nosed pliers or a similar device to set the jumper.
The Hardware/Software jumper is labeled “H” for hardware and “S” for
software (see the drawing below).
Hardware The Media Converter mode is determined by
the 4-position switch settings listed above.
Software The Media Converter mode is determined by
the most-recently saved, on-board
microprocessor settings.
The Far-End Fault jumper is labeled “FE” for enable Far-End Fault and “FD”
for disable Far-End Fault (see the drawing below).
Enable A fault on the fiber link causes the Media
Converter to transmit a Far-End Fault signal.
Disable No Far-End Fault signal is transmitted when a
fault occurs.
Software Mode
Hardware Mode
S
H
S
H
Disable Far-End Faul
t
Enable Far-End Fault
FE FD
FE FD
Installing the Slide-In-Module
CAUTION: Slots in the PointSystem™ Chassis without a Slide-in-Module
installed MUST have a protective plate covering the empty slot for Class A
and/or Class B compliance.
To install the CGETF10xx-15x Media Converter Slide-in-Module:
1. Locate an empty installation slot on the PointSystem™ Chassis.
2. Carefully slide the Slide-in-Module into the installation slot, aligning the
Slide-in-Module with the installation guides.
3. Ensure that the Slide-in-Module is firmly seated against the back of the
chassis.
4. Secure the Slide-in-Module by securing the panel fastener screw
(attached to the Slide-in-Module) to the chassis front.
CFMFF100
10BASE-2
CECF100
CFMFF100
0
50½
Link Alert
E
D
CETCF100
CFETF100
CFETF110
CFMFF100
LA
PWR
RXF
RXC
LNK
COL
SPD
PWR
FRX
CRX
FLNK
CLNK
SPD
PWR
FRX
CRX
FLNK
CLNK
10/100TX
RX
TX
10/100SX
100BASE-TX
RX
TX
100BASE-FX
Link Alert
E
D
0
50½
LA
PWR
RXF
RXC
LNK
COL
LKS
PWR
LKM
10BASE-2
10BASE-FL
10BASE-T
LKS
PWR
LKM
LKS
PWR
LKM
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
I
0
TERM
INIT
RX
TX
LNK
PWR
CPSMM120
SERIAL
10BASE-T
R
E
S
E
T
I
0
Panel Fastener Screw
4
CBFTF10xx-15x
Tech Support: 800-260-1312 International: 952-941-7600 7am-6pm CST (GMT-6:00)
INSTALLATION -- Continued
Install the Twisted-Pair Copper Cable
1. Locate or build IEEE 803.2™ compliant 10Base-T or 100Base-TX cables,
with straight-through RJ-45 cable, and with straight-through RJ-45
connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port
connector on the Media Converter.
3. Connect the RJ-45 connector at the other end of the cable to the RJ-45
port connector on the other device (switch, workstation, etc.).
NOTE: The MDI (straight-through) or MDI-X (crossover) cable connection is
configured automatically, according to the network conditions.
RJ-45 port
on the Media
Converter
RJ-45 port
on the other device
(switch, work station, etc.)
Install the Fiber Cable
1. Locate or build IEEE 803.2™ compliant 100Base-FX fiber cable with
male, two-stranded TX to RX connectors installed at both ends.
2. Connect the fiber cables to the CBFTF10xx-15x Media Converter as
described:
• Connect the male TX cable connector the female TX connector.
• Connect the male RX cable connector to the female RX connector.
3. Connect the fiber cables to the other device (another Media Converter,
hub, etc.) as described:
• Connect the male TX cable connector the female RX connector.
• Connect the male RX cable connector to the female TX connector.
Connect the fiber cable
to the Media Converter
as shown.
Connect the fiber cable
to the other device
(media converter,
hub, etc.) as shown
RX
TX
RX
TX
techsupport@transition.com -- Select the “Transition Now” Link for a Live Web Chat
5
INSTALLATION -- Continued
Power the Media Converter
The CBFTF10xx-15x Slide-in-Module Media Converter is powered through the
Point System™ chassis.
OPERATION
Status LEDs
Use the status LEDs to monitor the Media
Converter and the network connections.
FDPX (Fiber Duplex)
ON = full-duplex fiber connection.
Blinking = half-duplex fiber connection.
FLNK (Fiber Link)
ON = fiber link connection.
Blinking = fiber network activity.
PWR (Power)
ON = connection to external AC power.
TSPD (Twisted-Pair Speed)
ON = 100 Mb/s.
Blinking = 10 Mb/s.
TDPX (Twisted-Pair Duplex)
ON = full-duplex copper connection.
LED off = half-duplex copper connection.
TLKN(Twisted-Pair Link)
ON = copper link connection.
Blinking = copper network activity.
CBFTF150
PWRFDPX FLNK
TLNKTSPD TDPX
RX
TX
100Base-FX
10/100Base-TX
Loading...