Trane X13511537-01, BAYSTAT150A, THT02774 User Manual

Setup Instructions

Time Setup

To change the current time:

1. From the Home screen, press , , , , , .

2. Press , ,or to scroll between hours and minutes.

Trane Programmable Thermostat

X13511537-01/BAYSTAT150A/THT02774

More information: https://www.trane.com/stat

SAFETY WARNING

Only qualified personnel should install and service the equipment.The installation, starting up, and servicing of heating, ventilating, and airconditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or serious injury.When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that are attached to the equipment.

Hours

1. Press to increase or to decrease the hour or minute.

Changing Hours Changing Minutes

1. Press and hold for 2 seconds or wait 10 seconds to Save and Exit.

Minutes

PM PM

System Mode Setup

To set the system mode:

1. From the operating screen, press , . The current mode flashes.

2. Press or to select a mode.

OFF

Emergency

Heat

Note: Not all system choices may be available depending on the system configuration 0130.

3. Press and hold for 2 seconds or wait 10 seconds to Save and Exit.

Heat

Cool Auto H/C Off

Fan Mode

The fan mode is displayed only on systems configured with the fan

enabled. For systems configured with a fan, the fan setting is shown on the

display. In addition, the setting also appears on the display when pressing , , from the Home screen.

The fan mode setting can be overridden by pressing or when the

fan mode flashes. Press and hold for 2 seconds or wait 10 seconds to Save and Exit. Refer to the section, “Timed Override (TOV)”.

Auto Mode:

Auto Flashes

Important: When this thermostat is configured in



programmable mode (0140=1), then changing the Fan Mode from the Home screen puts the thermostat into

Timed Override (TOV) and is only temporary.The fan

goes back to the schedule setting after theTOV timer expires.

On Mode:

Arrows Flash

Timed Override (TOV)

A timed override can be usedto temporarilychangethe heatingsetpoint, cooling setpoint, fan mode, and/or occupancy setting from the programmed schedule.The override can be set for up to 99 days and up to 23 hours.

To enter a timed override:

1. From the operating screen, press or 2 times.The thermostat enters timed override mode with the hourglass and setpoint flashing.

2. Press or press or to move from either left or right through the selections. Some of the selections may not be available depending on the system type.

DAYS

HOURS

(Days)*

Cooling

Setpoint

3. Press or to change the value of the currently active (flashing) selections. Repeat steps 2 and 3 for the desired settings.

Note:To reach the DAYS setting, the user must press from the hours setting.

4. Press and hold for 2 seconds or wait 10 seconds to Save and Exit.

Note: The thermostat will return to the scheduled operation when:

• the override time expires, or

• pressing and holding

 

Fan

Setting

Important: When in timed override mode, if the system selection is changed (EmHeat, Heat, Cool, Auto, OFF), this change will take the thermostat out ofTOV mode.

Important: Whenever the thermostat is in TOV mode, a solid hour glass ( ) indicator displays at the bottom of the

screen.

Occupancy

Setting

an for 2 seconds.

Hours Heating

Setpoint

4 5

Create or Edit a Schedule

To create or edit a schedule:

1. Press , , , , .

Note: Each button shown above must be pressed within 10 seconds of the previous button. Once the user is in Schedule Change Mode, eachbuttonmustbe pressed within 45 seconds oftheprevious button in order to stay in Schedule Change Mode.

2. Press or to select the day(s) and to continue.

Mo Tu We Th Fr Sa Su

3. Press or to select the period and to continue.

4. Press or to change the StartTime

and to continue.

5. Press or to change the Heating

Setpoint and to continue.

6. Press or to change the Cooling

Setpoint and to continue.

7. Press or to select the Fan Setting

and to continue.

Auto On

4-Period

2-Period

defaults

6:00 am

8:00 am

6:00 pm

10:0 0 pm

8:00 am

10:0 0 pm

F (21.0 °C)

F (16.5 °C)

F (21.0 °C)

F (16.5 °C)

70°F (21.0 °C)

F (13.0 °C)

F (25.5 °C)

F (29.5 °C)

F (25.5 °C)

F (28.0 °C)

F (25.5 °C)

F (29.5 °C)

°°:

8. Repeat steps 2 through 7 for each day

(see step 2) and period (see step 3).To exit Schedule Change Mode, wait 45 seconds or press and hold for 2 seconds to Save and Exit.

Possible Scheduling Configurations (configuration option 0233):

• 1 day [default]; MoTuWeThFrSaSu (all days share a schedule).

• 5+1+1 days; MoT

uWeThFr Sa Su (Monday through Friday share

a schedule, Saturday and Sunday are each separate schedules).

• 5+2 days; MoT

uWeThFr SaSu (Monday through Friday share a

schedule, Saturday and Sunday share a schedule).

• 7 days; Mo Tu We Th Fr Sa Su (Eac

h day has a separate

schedule).

Note: Use

the worksheet on theright for planning orrecording schedule

settings. Default settings are ENERGY STAR® compliant.

Legend of Symbols

Morning Day Evening Night Time Heat Cool Fan

Trane optimizes the performance of homes and buildings around the world. A business of Ingersoll Rand, the leader in creating and sustaining safe, comfortable and energy efficient environments, Trane offers a broad portfolio of advanced controls and HVAC systems, comprehensive building services, and parts. For more information, visit www.IRCO.com.

Trane has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.

We are committed to using

environmentally conscious print practices that reduce waste.

Trane X13511537-01, BAYSTAT150A, THT02774 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual