TP-Link TXM431-LR, TXM431-SR User Manual
Installation Guide
10GBase SFP+ LC Transceiver
1. Wear an ESD-preventive wrist or ankle strap to prevent ESD damage to
the transceiver.
2. Insert the SFP into the SFP slot and rmly press it into place.
To ask questions, find answers, and communicate with TP-Link
users or engineers, please visit https://community.tp-link.com
to join TP-Link Community.
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides,
welcome to email techwriter@tp-link.com.cn.
Remove the SFPInstall the SFP
1. Wear an ESD-preventive wrist or ankle strap to prevent ESD damage to
the transceiver.
2. Disconnect the network ber-optic cables from the SFP.
©2020 TP-Link 7106508865 REV3.0.1
3. Remove the protective dust plug from the SFP.
4. Plug ber-optic cables into the SFP. Note that the SFP works without
any additional conguration.
Note:
1. Do not touch the output pins on the transceiver with your hand.
2. Always keep the protective dust plug on the SFP’s optical bores until you are ready to make a connection.
Caution:
DO NOT point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight.
3. Pull the safety latch downwards to release the SFP, and then pull it out
from the slot.
4. Reinstall the protective dust plug in the SFP’s optical bores and place it
on antistatic mat or a static shielding bag.
Connection
Only use the same transceiver model between switches for fast and reliable connectivity.
For simplicity, we will take TXM431-LR as an example.
Switch Switch
Specications
General Specications
Normal TXM431-LR
Wave Length 1310 nm
Standards and Protocols
Cable
Fiber Type
Max. Cable Length
Data Rate
Port Type
Power Support
Safety & Emission
DDM
SFP+ MSA
Hot Swappable
IEEE 802.3ae, TCP/IP
Single-mode Fiber
9/125 um Single-mode
10 km
10 Gbps
LC Duplex
3.3 V
FCC, CE
Ye s
Ye s
Ye s
TXM431-LR
TXM431-SR
850 nm
Multi-mode Fiber
50/125 um Multi-mode
300 m
TXM431-LR
Fiber
Environmental and Physical Specications
Product Operating Temperature 0˚C to 70˚C (32˚F to 158˚F)
Storage Temperature -40˚C to 85˚C (-40˚F to 185˚F)
Operating Humidity 10% to 90% RH, Non-condensing
Storage Humidity 5% to 90% RH, Non-condensing
TP-Link Compatible Products
TP-Link Switches with 10G SFP+ Slots
TX432
Note:
The SFP modules may be incompatible with other vendors’ devices. We
recommend that you use only TP-Link SFP modules on your TP-Link devices.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Avoid using this product during an electrical storm. There may be a remote risk
of electric shock from lightning.
Do not point or stare directly into the beam or into the optical port of the
transceiver when it is operating, as this can injure your eyesight.
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at
https://www.tp-link.com/en/ce.
Loading...