TP-Link TR-932D, TR-962D User Manual
!
!
!
off Which means that the fiber optic connector is operating
in half-duplex mode. Flashing green indicates for collision.
FDX/HDX Switch
FDX: The UTP port operate in full-duplex mode ;
HDX: The UTP port operate in haf-duplex mode;
Notice: You must reset the converter when you achieve the
configuration.
Installation Guide
Configuration
In order to achieve the aim of effectively expanding a Fast
Ethernet network, You can use the converter for example :
1. Position two converters back to back between the following
end devices.
10/100Base-TX
interface
10/100Base-TX
interface
100Base-FX
interface
Twisted-pair
Twisted-pair
Single/multi-mode fiber
Device A Device B
Converter Converter
65
2. Another effective application is to position one converter
directly between a 10/100Base-TX network and a fiber optic
(FX) device.
Installation Procedure
1. Converter to 10/100Base-TX Device (hub or switch)
Connection
Make sure that the length of twisted pair cable (Category-5)
between 10/100Base-TX device and converter is no longer
than 100 meters.
Connect one end of twisted pair cable to RJ45 jack on the
converter and the other end of the cable to the RJ45 jack on
the 10/100Base-TX device.
2. Converter to Converter or 100Base-FX Device Connection
Connect one (SC) end of a fiber cable to the SC connector
!
!
10/100Base-TX
interface
100Base-FX
interface
Twisted-pair
Single/multi-mode fiber
Device A Device B
Converter
on the converter and the other end of the cable to the SC
connector on the other converter or 100Base-FX device.
3. Turn on the power
Appendix Specifications
Standard: IEEE 802.3/IEEE 802.3u
Connector: 1 SC fiber optic; 1 RJ45 jack
Max. Distance: Twisted Pair(cat5):100m
Multi-mode Fiber Optic: 2km
Single-mode Fiber Optic: 20/40/60km
Power: external power supply, 9V 0.8A
Temperature: Operation: -10 to 50
Storage: -40 to 70
Humidity: 10%-90% (non-condensing)
Dimensions: 123mmx67mmx24 mm (LxWxH)
7
TR-932D
TR-962D
User's Guide
71030388
Rev 3.0
10/100Mbps Fast Ethernet Converter
3 4
Table of Contents
Introduction..........................................................................2
Features...............................................................................2
Network Cable Supported.....................................................3
Package Contents................................................................3
Appearance Indication..........................................................4
Installation Guide.................................................................5
Appendix Specifications......................................................7
Introduction
The TR-9XX series products are 10/100Mbps fast ethernet
converter. The converter mediates between a 10/100Base-TX
segment and a 100Base-FX segment.It is primarily designed for
large, more high speed/bandwidth demanding workgroups that
require expansion of the Fast Ethernet network.
Features
Complies with 802.3u 10/100Base-TX and 100Base-FX
standard.
Provide one SC fiber connector and one UTP connector.
Auto-detection of half/full duplex transfer mode for TX port.
Auto-negotiation of 10/100Mbps rate and Auto-Crossover
for TX port.
Provide switch configuration of half/full duplex transfer
mode for FX port.
Extend fiber distance up to 2km for multi-mode fiber and
!
!
!
!
!
!
AC power connector
RJ45 connetor
SC fiber connetor
!
!
!
20-60km for single-mode fiber.
Easy-to-view LED indicators provide status to monitor
network activity easily.
External power supply.
Network Cable Supported
The connectors and network cables supported by the converter
are listed in the following:
UTP: Cat 5 Twisted-Pair
Fiber SC: 1300nm 62.5/125,50/125um Single/Multi-mode fiber
Package Contents
Before start using the products, make sure that what you have is
what you ordered.
The Converter includes:
TR-932D RJ45--SC 2km Multi-mode Fiber,Cat-5
TR-962D-20 RJ45--SC 20km Single-mode Fiber,Cat-5
TR-962D-40 RJ45--SC 40km Single-mode Fiber,Cat-5
TR-962D-60 RJ45--SC 60km Single-mode Fiber,Cat-5
Type Connetor Transmission Distance Transmission Media
!
!
!
!
!
!
!
!
One Converter
One AC adapter
This User's Guide
Appearance Indication
LED Indicators
This converter has LED indicators which can provide a real-time
report. When you take a look at these indicators, you will know
what's happening on your network.
Power(green) Lights when the adapter is properly
plugged in.
TX_SPD(green) Lights when the UTP ports is connected
to 100Base-Tx device.
TX_LINK/ACT(green) Steady green indicates that a valid
link exists. Flashing green indicates that the converter is
receiving data or transmitting data from the RJ45 connector.
FX_LINK/ACT(green) Steady green indicates that a valid link
exists. Flashing green indicates that the converter is receiving
data or transmitting data from the Fiber Optic connector.
FX_FDX/COL(green) Steady green indicates that the fiber
optic connector is operating in full-duplex mode. The light is
21
Loading...