Installation Guide
2x2 MIMO Sector Antenna
TL-ANT2415MS & TL-ANT5819MS
Contents
Introduction
Specifications
Safety Notice
Package Contents
Installation Requirements
Hardware Overview
Hardware Installation
1
1
2
2
3
3
4
Introduction
The TL-ANT2415MS, 2.4GHz 15dBi 2x2 MIMO Sector Antenna,
can be used together with the outdoor wireless Base Station
WBS210 to achieve a stable long-distance signal transmission.
The TL-ANT5819MS, 5GHz 19dBi 2x2 MIMO Sector Antenna,
can be used together with the outdoor wireless Base Station
WBS510 to achieve a stable long-distance signal transmission.
Specications
Electrical Specifications TL-ANT2415MS TL-ANT5819MS
Frequency Range
Gain
VSWR
HPOL Beamwidth
VPOL Beamwidth
Elevation Beamwidth
Electrical Downtilt
F/B Ratio
Polarization
Impedance
Connector
2.3 to 2.7GHz
15dBi
1.8 Max
120° (6dB) & 90° (3dB)
120° (6dB) & 90° (3dB)
8°
0°
25dB Min
Horizontal & Vertical
50Ω
RP-SMA Female
5.0 to 6.0GHz
19dBi
1.8 Max
120° (6dB) & 90° (3dB)
120° (6dB) & 90° (3dB)
4°
0°
28dB Min
Horizontal & Vertical
50Ω
RP-SMA Female
Mechanical Specifications
Antenna Dimension
Weight
Rated Wind Velocity
Mounting
700×133×57mm
3.5Kg
241Km/h
Pole Mount
1
Safety Notice
Heed all warnings:
Mount the antenna at a safe location, far away from power lines, lamp
posts, and other electrical cables.
Do not mount the antenna in the rain or thunderstorm.
Avoid using this product during an electrical storm. There may be a
remote risk of electric shock from lightning.
For your own safety, please seek a qualified service technician for
assistance.
Package Contents
Adjustable Pole-mount BracketAntenna Mount Bracket
Installation Guide
2x2 MIMO Sector Antenna
TL-ANT2415MS & TL-ANT5819MS
Protective Shroud
Installation Guide
Antenna
Hex Nuts
(M4, Qty.4)
Pole-mount Clamps
(Qty.2)
Bolts with Nut and Lock
Washer Assemblies
(M8×85, Qty.4)
Flat Washers
(φ6, Qty.4)
2
RF Cables
(Qty.2)
Bolts with Nut and Lock
Washer Assemblies
(M6×35, Qty.2)
Spring Washers
(φ6, Qty.4)
Installation Requirements
Outdoor Wireless Base Station (sold separately)
Wrenches
Hardware Overview
Back View
Bubble Level
RF Connectors
Base Station
Mount Bracket
Base Station/Shroud
Lock Release Lever
Assembled Side View
3
Adjustable
Pole-mount Bracket
Antenna Mount Bracket
Protective Shroud
Hardware Installation
1. Attach the RF Cables to the Base Station.
2. Attach the Base Station to the Base Station Mount Bracket as
follows:
a. Align the mounting tabs on the back of the Base Station with
the four mounting slots on the Base Station Mount Bracket.
b. Slide the Base Station down until it locks into place.
4
3. Connect the other ends of the RF Cables to the RF Connectors
on the antenna.
4. Slide the Protective Shroud down over the Base Station until it
locks onto the Base Station Mount Bracket.
5
5. Attach the Antenna Mount Bracket to the four studs located
on the antenna using the Flat Washers, Spring Washers, and
Hex Nuts.
6. Attach the Adjustable Pole-mount Bracket and Pole-mount
Clamps to the pole using four M8x85 Bolts with Nut and Lock
Washer Assemblies.
Note: Pole diameter ranges from 40mm to 80mm.
6
7. Mount the Antenna Mount Bracket to the Adjustable
Pole-mount Bracket using two M6x35 Bolts with Nut and Lock
Washer Assemblies.
Note: Do not over-tighten these bolts and nuts to allow angle adjustment
later.
8. Adjust the desired elevation angle of the antenna using the
scale marked on the Antenna Mount Bracket, and then tighten
the bolt and nut assemblies.
7
For technical support and other information, please visit
http://www.tp-link.com/support, or simply scan the QR code.
©2017 TP-Link 7106507064 REV2.0.2
Loading...