TP-Link EAP613 Quick Installation Guide [EN]

Hardware Installation

2

Option 2: Wall Mounting

Option 3: Junction Box Mounting

Quick Installation Guide

Wireless Access Point

Setup with videos

Visit https://www.tp-link.com/support/setup-video/ or scan the QR code

to search for the setup video of your product model.

Note: EAP650 is used as an example throughout the Guide. Images may dier from your actual product.

©2023 TP-Link 7106510424 REV1.5.0

1

Hardware Overview

The EAP can be mounted to the ceiling, the wall, or in a junction box, using the screws in the
package. Choose the appropriate mounting and installation steps below.
Note: This product requires heat dissipation through the metal bracket during use, please be
careful not to touch the metal bracket in the heat dissipation.

Option 2: Wall MountingOption 1: Ceiling Mounting Option 3: Junction Box Mounting

Option 1: Ceiling Mounting

Note: Make sure that the ceiling tile is larger than the EAP.

Wing NutsWashers Pan-head Screws

Plastic Wall Anchors

Self-tapping Screws

1

If your Ethernet cable feeds through the wall,
position the mounting bracket below the cable
hole. Mark positions for the screw holes and
drill 6 mm (15/64 in) diameter holes at the
marked positions.

2

Insert the plastic wall anchors into the 6 mm
diameter holes.

Prepare the cables and the junction box in advance. Ensure that the mounting holes align
to your junction box.

*Compatible wall junctions:

1

Route the cables through the square cable
hole on the mounting bracket, and secure the
mounting bracket to the junction box using

screws.

Front Panel

LED Indicator

Blue On:

Orange On:

Off:

Flash: • Flash twice:

* When the Locate feature is activated in the Omada controller, the LED ashes quickly to locate and identify the

device. The LED will ash for 10 minutes. You can disable the feature manually to stop it from ashing.

Working normally/Initializing. For EAPs with dual-color LED: Normal power supply

For EAPs with dual-color LED: Low power supply

Working abnormally/Power o/LED is turned o.

Initialization is completed.

• Flash quickly:

• Flash once per second:

• Flash Slowly:

The EAP is resetting, or the Omada controller is locating the device*.

The EAP is upgrading.

The EAP is in the isolated state.

Rear Panel

Drill Hole for Ethernet cable

1

Remove the ceiling tile.

2

Place the mounting bracket in the center of the
ceiling tile. Mark positions for the screw holes
and a location for the Ethernet cable hole.
Drill 4 mm (5/32 in) diameter holes for the screws
and a 25 mm (63/64 in) diameter hole for the
Ethernet cable at the marked positions.

3

Secure the mounting bracket to the ceiling tile
using pan-head screws, washers, and wing nuts,
as shown on the left.

3

Secure the mounting bracket to the wall by
driving the self-tapping screws into the
anchors. Make sure that the shoulders of the
mounting bracket are on the outside.

4

Connect the Ethernet cable to the Ethernet

port on the EAP.

2

Connect the Ethernet cable to the Ethernet

port on the EAP.

3

Attach the EAP to the mounting bracket by
rotating it until it locks into place, as shown on
the left.

Power Supply

3

The EAP can be powered via a power adapter or a PSE device (such as a PoE switch) which
complies with Power Source Class 2 ( PS2) or Limited Power Source (LPS) of IEC 62368-1.

Option 1: Via PoE Switch

Connect an Ethernet cable from the PoE switch to the Ethernet port.

Note: For PoE power supply specications, refer to the product label.

RESET

With the device powered on, press and hold the button for about 5 seconds until the LED flashes quickly. Then
release the button. The device will restore to factory default settings.

Ethernet Port: ETH (PoE)

The port is used to connect to a router or a switch to transmit data, or to a PSE (Power Sourcing Equipment),
such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet cable.

Note: For EAPs with 10Gbps port, if you use a CAT5E cable, the 10Gbps link of the Ethernet port is less than 55m. To achieve a longer
transmission distance, use a shielded CAT6A cable.

Power Port

Plug one end of the power adapter to this port and the other end to a standard electrical wall outlet to power the

E AP.

Note: Power adapter is not included in the package contents of certain models. For details, refer to the product specications or
datasheet. For power supply specications, refer to the product label.

4

Feed the Ethernet cable through the hole and

set the ceiling tile back into place.

5

Connect the Ethernet cable to the Ethernet port.

Please pay attention to the triangle sign. Attach

the EAP to the mounting bracket, then rotate it
until it locks into place, as shown on the left.

5

Attach the EAP to the mounting bracket by
rotating it until it locks into place, as shown on
the left.

PoE Switch

Option 2: Via Power Adapter

Plug one end of the power adapter into the power port of the EAP and the other end to a

standard electrical wall outlet.

Note: Power adapter is not included in the package contents of certain models. For details, refer to the product specications or
datasheet. For power supply specications, refer to the product label.

Power Adapter

Switch

4

To ask questions, find answers, and communicate with TP-Link users or engineers,
please visit https://community.tp-link.com to join TP-Link Community.

Software Conguration

Choose from the following methods to set up your EAPs:

• Method 1: Standalone Mode

To configure and manage EAPs separately (Convenient for a small network with only a few devices)

• Method 2: Controller Mode

To configure and manage EAPs in batches on a central platform, namely Omada Controller.

Method 2: Controller Mode

Choose a type of Omada Controller:

Type 1: Omada Cloud-Based Controller

Omada Cloud-Based Controller is a good alternative without the need to install the
software controller on a PC or purchasing the hardware controller.

Licenses need to be purchased additionally.

• Type 2: Omada Software Controller

On a PC with Windows OS or Linux OS, download the software controller from
https://www.tp-link.com/support/download/omada-software-controller/. Then run the file and
follow the wizard to install and launch the controller.

To manage your devices, the software controller needs to keep running on your computer.

• Type 3: Omada Hardware Controller

If you have no spare PC to keep running the software controller in the network, you can

purchase the hardware controller.

For more details, refer to the Installation Guide of your hardware controller.

Method 1: Standalone Mode

EAP

Internet

Router

Note:

• Before you start, be sure to power up and connect your devices according to the topology figure.

• A DHCP server (typically a router with DHCP function enabled) is required to assign IP addresses

to the EAPs and clients in your local network.

Via Omada App

1. Download and install the TP-Link Omada App from App Store or Google Play.

EAP

Clients

EAP

Omada Cloud

Router

Switch

EAPEAP EAP EAP

Clients

Note:

• Before you start, be sure to power up and connect your devices according to the topology figure.

• A DHCP server (typically a router with DHCP function enabled) is required to assign IP addresses to

the EAPs and clients in your local network.

Web Configuration

1. Contact the sales staff to grant the Omada Cloud-Based Controller permission.

Router

Switch

Controller

Omada Software Controller

running on the Host PC

Note:

• Before you start, be sure to power up and connect your devices according to the topology figure.

• A DHCP server (typically a router with DHCP function enabled) is required to assign IP addresses to

the EAPs and clients in your local network.

• Omada Controller must have network access to your Omada devices (the router, switch, and EAPs) in
order to find, adopt, and manage them.

EAP EAP EAP

Clients

Via Omada App

1. Download and install the TP-Link Omada App from App Store or Google Play.

or

Router

Switch

Omada Hardware Controller EAP EAP EAP

Clients

Note:

• Before you start, be sure to power up and connect your devices according to the topology figure.

• A DHCP server (typically a router with DHCP function enabled) is required to assign IP addresses

to the EAPs and clients in your local network.

• Omada Controller must have network access to your Omada devices (the router, switch, and
EAPs) in order to find, adopt, and manage them.

Via Omada App

1. Download and install the TP-Link Omada App from App Store or Google Play.

or

or

Scan for Omada Omada

2. Connect your mobile device to the EAP by using the default SSIDs printed on the label
at the bottom of the product.

3. Open the Omada App, go to the Standalone Devices > APs page, and wait for the
EAP to appear. Tap on the EAP to congure it.

The Omada App is designed to help you quickly configure common settings. If you want
to configure advanced settings, use the web page of your EAP or use Controller Mode.

Via Web Browser

1. Connect your device to the EAP by using the default SSIDs printed on the label at the

bottom of the product.

2. Launch a web browser and enter http://tplinkeap.net

both Username and Password to log in.

3. Set up a new Username and Password for secure management purpose. Then you can
configure the AP.

To configure other EAPs, connect your device to each EAP by the corresponding default
SSID and repeat the steps above. You can configure some basic functions in Standalone
Mode. If you want to configure advanced functions, use Controller Mode.

Safety Information

• Keep the device away from water, re, humidity or hot environments.

• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

• Do not use the device where wireless devices are not allowed.

• Do not use damaged charger or USB cable to charge the device.

• Do not use any other chargers than those recommended.

• Adapter shall be installed near the equipment and shall be easily accessible.

in the address bar. Use admin for

2. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar. Log

in with your TP-Link ID.

https://omada.tplinkcloud.com

3. Click + Add Controller and add a Cloud-Based Controller. Then you can launch the

controller to adopt and manage devices.

* Management via Omada App

After adding a Cloud-Based Controller, you can also manage it via the Omada App.

1. Download and install the TP-Link Omada App from App Store or Google Play.

or

Scan for Omada Omada

2. Launch the Omada App and log in with your TP-Link ID. Then go to Cloud Access. A list of

controllers that have been bound with your TP-Link ID will appear. Then you can launch
the controller to adopt and manage devices.

For the detailed configurations, refer to the User Guide of the controller and EAPs. The guides can
be found on the download center of our official website: https://www.tp-link.com/support/download/.

For technical support, the user guide and other information,
please visit https://www.tp-link.com/support, or simply scan the QR code.

Scan for Omada Omada

2. Launch your Omada App and configure the controller at a local site or remote site.

•

Local Management

a. Connect your mobile device to the EAP by using the default SSIDs printed on the

label at the bottom of the product.

b. Launch the Omada App and go to Local Access, tap the + button on the upper-right

corner to add the controller. Then you can launch the controller to adopt and manage

devices.

•

Remote Management

Note: Before you start, make sure that both your controller and mobile device can access the

internet.

a. Make sure that Cloud Access is enabled on your controller and your controller has

been bound with your TP-Link ID.

b. Launch Omada App and log in with your TP-Link ID. Then go to Cloud Access. A list

of controllers that have been bound with your TP-Link ID will appear. Then you can

launch the controller to adopt and manage devices.

Via Web Browser

1. Open the controller’s web page.

Launch the software controller on your PC. After the initiation process, the controller
automatically opens its web page. If not, click Launch a Browser to Manage the Network.

2. On the controller’s web page, follow the wizard to complete the quick setup. Then you can

launch the controller to adopt and manage devices.

3. (For Remote Management) You can remotely access and manage your controller via
Omada Cloud Service.

Note: Before you start, make sure that both your controller and PC can access the internet.

a. Make sure that Cloud Access is enabled on your controller and your controller has

been bound with your TP-Link ID. On the controller’s web page, go to Settings > Cloud
Access to enable Cloud Access and bind your TP-Link ID. If you have set it up in the

quick setup, skip this step.

b. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar.

Enter your TP-Link ID and password to log in. A list of controllers that have been bound
with your TP-Link ID will appear. Then you can launch the controller to adopt and

manage devices.

Scan for Omada Omada

2. Launch your Omada App and configure the controller at a local site or remote site.

•

Local Management

a. Connect your mobile device to the EAP by using the default SSIDs printed on the

label at the bottom of the product.

b. Launch the Omada App and go to Local Access, tap the + button on the

upper-right corner to add the controller. Then you can launch the controller to

adopt and manage devices.

•

Remote Management

Note: Before you start, make sure that both your controller and mobile device can access the

internet.

a. Make sure that Cloud Access is enabled on your controller. By default, Cloud

Access is enabled. Make sure that the Cloud LED is flashing slowly.

b. Launch Omada App and log in with your TP-Link ID. Then go to Cloud Access. Tap

the + button on the upper-right to add your controller. Then you can launch the
controller to adopt and manage devices.

Via Web Browser

1. Open the controller’s web page.

Find the IP address of the controller on the gateway router’s DHCP client list. Enter the
IP address in the address bar to open its web page.

2. On the controller’s web page, follow the wizard to complete the quick setup. Then you

can launch the controller to adopt and manage devices.

3. (For Remote Management) You can remotely access and manage your controller via
Omada Cloud Service.

Note: Before you start, make sure that both your controller and PC can access the internet.

a. Make sure that Cloud Access is enabled on your controller. By default, Cloud

Access is enabled. Make sure that the Cloud LED is flashing slowly.

b. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar.

Enter your TP-Link ID and password to log in. Click + Add Controller and choose
Hardware Controller to add your controller. Then you can further configure the

controller.