Tp-link Archer C2 Instruction Manual [ru]

Quick Installation Guide

AC900 Wireless Dual Band Gigabit Router

Connecting the Hardware

If your Internet connection is through an Ethernet cable from the wall instead of through a DSL / Cable / Satellite modem, connect the Ethernet cable directly to the router’s Internet port, then follow step 4 and 5 to complete the hardware connection.

Power adapter

Turn on the router.

Power adapter

Internet

Modem

Router

Turn o the modem, and remove

the backup battery if it has one.

Connect the modem to the

Internet port on your router with an Ethernet cable.

Turn on the modem, and

then wait about 2 minutes for it to restart.

Verify that the hardware

connection is correct by checking these LEDs.

Power

2.4G On

5G On

Internet

Note: If the 2.4G LED and 5G LED are o, please press and hold the Wi-Fi/WPS button on the rear panel until they are on.

Configuring the Router

Connections are available

Wireless Network Connection

Create a new username and password and click Confirm. Then follow the

step-by-step instructions of the Quick Setup to complete the initial configuration.

FAQ (Frequently Asked Questions)

1. Connecting your computer to the router (Wired or Wireless)

Wired

Turn o the Wi-Fi on your computer and connect the devices as shown below:

Ethernet cable

Wireless

Find the SSID (network name) and Wireless Password printed on the label at the bottom of the router.

Click the network icon of your computer or go to Wi-Fi Setting of your smart device,

and then select the SSID to join the network.

Computer Smart Device

< Settings

Wi-Fi

Internet Connection Type

Time zone

Note: If you are not sure of the Internet Connection Type, please click Auto Detect.

Wireless Settings

Summary

Test Internet Connection

Tether App

TP-LINK Tether app provides a simple, intuitive way to access and manage your router.

Block unwelcome users from connecting to your network

Change the basic wireless network settings

Q1. What can I do if the login window does not appear?

If the computer is set to a static or fixed IP address, change the setting to obtain an IP address automatically.

Verify that http://tplinkwifi.net is correctly entered in the web browser. Alternatively, enter http://192.168.0.1 or http://192.168.1.1 in the web browser and press Enter.

Use another web browser and try again.

Reboot your router and try again.

Disable then re-enable the network adapter being used.

Q2. What can I do if I cannot access the Internet?

Check if the Internet is working properly by connecting a computer directly to the modem using an Ethernet cable. If it is not, contact your Internet Service Provider.

Log into the Web Management page of the router, and go to the Advanced > Status page to check whether the Internet IP address is valid or not. If it is, please run the Quick Setup again; otherwise, recheck the hardware connection.

Reboot your router and try again.

For cable modem users, log in to the Web Management page of the router. Go to Advanced > Network > Internet > MAC Clone, click Use Current Computer

MAC Address and click Save, then reboot both the modem and the router.

Q3. How do I restore the router to its factory default settings?

With the router powered on, press and hold the Reset button on the back until the Power LED starts blinking.

Log into the Web Management page of the router. Go to Advanced > System Tools > Backup & Restore, click Factory Restore. The router will restore and reboot automatically.

TP-LINK_XXXX TP-LINK_XXXX_5G

√

Connect automatically Connect

CHOOSE A NETWORK...

TP-LINK_XXXX TP-LINK_XXXX_5G

Other...

2. Configure the router using a web browser

Launch a web browser, enter http://tplinkwifi.net or http://192.168.0.1 in the address bar. Use admin for both username and password, and then click Login.

Note: If the login window does not appear, please refer to FAQ > Q1.

http://tplinkwifi.net

admin

Tether

View information about clients connected to your router

Set up Parental Controls with access time

How to begin?

1. Download the TP-LINK Tether app from the Apple App Store or Google Play.

2. Ensure your smart device is wirelessly connected to the home network.

3. Launch the Tether app and start managing your home network.

More Features

Scan to download

Q4. What can I do if I forgot my web management password?

Refer to FAQ > Q3 to reset the router, and then use admin (all lowercase) for both username and password to log in.

Q5. What can I do if I forgot my wireless network password?

The factory default Wireless Password is printed on the label of the router. Connect a computer directly to the router using an Ethernet cable.

router’s Web Management page, and go to Basic > Wireless to obtain or reset your wireless password.

If your questions are not listed here, please refer to the support page at

www.tp-link.com.

Log into the

admin

The TP-LINK router is equipped with various features, such as Guest Network, Parental Controls, Access Control, etc. You can log in to the router’s Web Management page http://tplinkwifi.net to apply these functions. For instructions, please refer to the User Manual at www.tp-link.com.