Since the doors can be locked without a
key, you should always carry a spare key
in case you accidentally lock your key
inside the vehicle.
10
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend you to write down the key
number and keep it in safe place.
2002 MY TACOMA_U (OM35786U)
LOCKING AND UNLOCKING WITH KEY
Insert the key into the keyhole and turn
it.
To lock: Turn the key forward.
To unlock: Turn the key backward.
Vehicles with power door lock system—
All the doors lock and unlock simultaneously with either front door. In the driver’s door lock, turning the key once will
unlock the driver’s door and twice in succession will unlock all the door simultaneously.
LOCKING AND UNLOCKING WITH
INSIDE LOCK BUTTON
Move the lock button.
To lock: Push the button downward.
To unlock: Pull the button upward.
Closing the door with the lock button
pushed in will also lock the door. Be careful not to lock your keys in the vehicle.
Vehicles with power door lock system—
The doors cannot be locked if you leave
the key in the ignition switch.
Driver’s side
’02 Tacoma U (L/O 0109)
LOCKING AND UNLOCKING WITH
POWER DOOR LOCK SWITCH
Push the switch.
To lock: Push the switch on the front side.
To unlock: Push the switch on the rear
side.
All the doors lock or unlock simultaneously.
All the doors cannot be unlocked with the
power door lock switch by the following
cases:
Either front door is locked by the key.
Either front door is closed with the
inside door lock button pushed in.
Passenger’s side
2002 MY TACOMA_U (OM35786U)
11
’02 Tacoma U (L/O 0109)
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the vehicle. Along with the proper use of
seat belts, locking the doors helps
prevent the driver and passengers
from being thrown out from the vehicle during an accident. It also helps
prevent the doors from being opened
unintentionally.
Power windows
REAR DOOR CHILD–PROTECTORS
Move the lock lever to the “LOCK”
position as shown on the label.
This feature allows you to lock a rear
door so it can be opened from the outside
only, not from inside. We recommend using this feature whenever small children
are in the vehicle.
12
The windows can be operated with the
switch on each door.
The power windows work when the ignition
switch is in the “ON” position.
Key off operation: If both front doors are
closed, they work for 43 seconds even
after the ignition switch is turned off. They
stop working when either front door is
opened.
OPERATING THE DRIVER’S WINDOW
Use the switch on the driver’s door.
Normal operation: The window moves as
long as you hold the switch.
To open: Lightly push down the switch.
To close: Pull up the switch.
2002 MY TACOMA_U (OM35786U)
’02 Tacoma U (L/O 0109)
Window lock
switch
Automatic operation (to open only):
Push the switch completely down and then
release it. The window will fully open. To
stop the window partway, lightly pull the
switch up and then release it.
OPERATING THE PASSENGERS’
WINDOWS
Use the switch on each passenger’s
door or the switches on the driver’s
door that control each passenger’s window.
The window moves as long as you hold
the switch.
To open: Push down the switch.
To close: Pull up the switch.
If you push in the window lock switch on
the driver’s door, the passengers’ windows
cannot be operated.
2002 MY TACOMA_U (OM35786U)
13
CAUTION
To avoid serious personal injury, you
must do the following.
Always make sure the heads, hands
and other parts of the bodies of all
occupants are kept completely inside the vehicle before you close
the power windows. If someone’s
neck, head or hands gets caught in
a closing window, it could result in
a serious injury. When anyone
closes the power windows, make
sure that he/she operates the windows safely.
When small children are in the ve-
hicle, never let them use the power
window switches without supervision. Use the window lock switch to
prevent them from making unexpected use of the switches.
Never leave small children alone in
the vehicle, especially with the ignition key still inserted. They could
use the power window switches and
get trapped in a window. Unattended children can be involved in
serious accidents.
’02 Tacoma U (L/O 0109)
Quarter windows
(Xtra–cab models)
To open the quarter window, pull the
latch handle toward you and swing it
fully out.
When closing the window, make sure it is
completely closed.
Rear window
To unlock the rear window, pull the
latch handle toward you.
When closing the window, make sure it is
completely closed.
14
2002 MY TACOMA_U (OM35786U)
’02 Tacoma U (L/O 0109)
TailgateHood
To open the tailgate, pull the handle up.
The support cables will hold the tailgate
horizontal.
See “Luggage stowage precautions” in
Section 2 for precautions in loading luggage.
After closing the tailgate, try pulling it toward you to make sure it is securely
locked.
NOTICE
Avoid driving with the tailgate open.
To lower the tailgate fully, release the
support brackets from the lugs as
shown.
NOTICE
Lower the tailgate gently when it is
unhooked.
Make sure the tailgate is securely
caught by the support brackets before closing the tailgate.
2002 MY TACOMA_U (OM35786U)
To open the hood:
1. Pull the hood lock release lever. The
hood will spring up slightly.
CAUTION
Before driving, be sure that the hood
is securely closed and locked. Otherwise, the hood may open unexpectedly while driving and an accident may
occur.
15
’02 Tacoma U (L/O 0109)
Fuel tank cap
2. In front of the vehicle, pull up the
auxiliary catch lever and lift the
hood.
16
3. Hold the hood open by inserting the
support rod into the slot.
Before closing the hood, check to see that
you have not forgotten any tools, rags,
etc. and return the support rod to its
clip—this prevents rattles. Then lower the
hood and make sure it locks into place.
If necessary, press down gently on the
front edge to lock it.
CAUTION
After inserting the support rod into
the slot, make sure the rod supports
the hood securely from falling down
on to your head or body.
2002 MY TACOMA_U (OM35786U)
With tachometer
Without tachometer
’02 Tacoma U (L/O 0109)
This indicates that the fuel filler door
is on the left side of your vehicle.
Type A
Type B
1. Type A—
To open the fuel filler door, pull the
door toward out as shown.
Type B—
To open the fuel filler door, insert
the key and turn it counterclockwise.
When refueling, turn off the engine.
CAUTION
Do not smoke, cause sparks or al-
low open flames when refueling.
The fumes are flammable.
When opening the cap, do not re-
move the cap quickly. In hot weather, fuel under pressure could cause
injury by spraying out of the filler
neck if the cap is suddenly removed.
Do not fill a fuel container on a
plastic truck bed liner, a rubber
truck bed mat, or any other insulating material. A static electricity
charge could cause a spark and fire
hazard. The proper procedure is to
place an approved fuel container on
the ground away from the truck for
filling.
2002 MY TACOMA_U (OM35786U)
17
Type A
’02 Tacoma U (L/O 0109)
2. To remove the fuel tank cap, turn
the cap slowly counterclockwise,
then pause slightly before removing
it. After removing the cap, hang it
on the cap hanger (type A) or hook
it on the inside of the fuel filler door
(type B).
It is not unusual to hear a slight swoosh
when the cap is opened. When installing,
turn the cap clockwise till you hear a
click.
If the cap is not tightened securely, the
malfunction indicator lamp comes on.
Make sure the cap is tightened securely.
The indicator lamp goes off after driving
several times. If the indicator lamp does
not go off, contact your Toyota dealer as
soon as possible.
CAUTION
Make sure the cap is tightened se-
curely to prevent fuel spillage in
case of an accident.
Use only a genuine Toyota fuel tank
cap for replacement. It is designed
to regulate fuel tank pressure.
Detachable moon roof—
—Moon roof precautions
CAUTION
To avoid serious personal injury, you
must do the following.
While the vehicle is moving, always
keep the heads, hands and other
parts of the bodies of all occupants
away from the roof opening. Otherwise, they could be seriously injured if the vehicle stops suddenly
or if the vehicle is involved in an
accident.
Never sit on top of the vehicle
around the roof opening.
Never attempt to remove the moon
roof panel while driving. Otherwise,
the panel may become a hazard by
falling into or flying off the vehicle.
After installing the moon roof pan-
el, make sure they are firmly secured by pushing up on the underside of the panel.
Never put your hands between the
moon roof panel and the surrounding roof.
Type B
18
2002 MY TACOMA_U (OM35786U)
—Tilting up and closing—Removing
’02 Tacoma U (L/O 0109)
To tilt up the moon roof, first pull down
on the handle while pushing in one of
the lock buttons. Then push up the
moon roof until it locks.
After tilting up the moon roof, make sure
the handle is securely in place.
When closing the moon roof, slowly pull
down the handle while supporting the roof
with your hand. Close and lock the moon
roof by pushing the handle. Be sure to
use your palm to push the handle. After
closing the moon roof, make sure it is
securely locked.
1. Pull the handle down while pushing
in one of the lock buttons.
2002 MY TACOMA_U (OM35786U)
2. Push in the retaining spring arms as
shown and push up the moon roof.
19
—Installing
’02 Tacoma U (L/O 0109)
3. Push back the auxiliary catch to release it from the hook. Then lift the
moon roof panel and pull it out.
20
1. Insert the flat hinges of the moon
roof panel into the cutouts on the
body. Then slowly lower it while
holding the roof with your hands.
Make sure both flat hinges are inserted
into the cutouts.
2002 MY TACOMA_U (OM35786U)
2. Press in the retaining spring arms
and insert them into the holes. Then
push the handle up with the palm of
your hand and lock the roof.
Detachable sun shade
To remove: Support the sun shade panel with your hand while you unlock the
sun shade by turning the knob counterclockwise.
To install: Hang the two hinges of the
sun shade panel onto the hooks provided. Then push up the sun shade
panel while turning the knob counterclockwise.
’02 Tacoma U (L/O 0109)
CAUTION
For safety, do not remove the sun
shade while driving.
While the vehicle is being driven, all vehicle occupants should have the seatback
upright, sit well back in the seat and properly wear the seat belts provided.
CAUTION
’02 Tacoma U (L/O 0109)
Front seats—
—Seat adjustment precau tio ns
Adjust the driver’s seat so that the foot
pedals, steering wheel and instrument
panel controls are within easy reach of
the driver.
CAUTION
While adjusting the seat, do not put
your hands under the seat or near
the moving parts. You may catch
and injure your hands or fingers.
Do not drive the vehicle unless the
occupants are properly seated. Do
not allow sitting on top of a
folded–down seatback, or in the
luggage compartment or cargo area.
Persons not properly seated and/or
properly restrained by seat belts
can be severely injured in the event
of emergency braking or a collision.
During driving, do not allow pas-
sengers to stand up or move
around between seats. Severe injuries can occur in the event of emergency braking or a collision.
24
Adjustments should not be made
while the vehicle is moving, as the
seat may unexpectedly move and
cause the driver to lose control of
the vehicle.
When adjusting the seat, be careful
that the seat does not hit a passenger or luggage.
After adjusting the seat position,
try sliding it forward and backward
to make sure it is locked in position.
After adjusting the seatback, push
back your body to make sure it is
locked in position.
Do not put objects under the seats.
The objects may interfere with the
seat–lock mechanism or unexpectedly push up the seat position adjusting lever; the seat may suddenly
move, causing the driver to lose
control of the vehicle.
2002 MY TACOMA_U (OM35786U)
—Adjusting front seats
’02 Tacoma U (L/O 0109)
1. SEAT POSITION ADJUSTING LEVER
Pull the lever up. Then slide the seat
to the desired position with slight
body pressure and release the lever.
2. SEATBACK ANGLE ADJUSTING
LEVER (except bench seat)
Lean forward and pull the lever up.
Then lean back to the desired angle
and release the lever.
CAUTION
To reduce the risk of sliding under
the lap belt during a collision, avoid
reclining the seatback any more than
needed. The seat belts provide maximum protection in a frontal or rear
collision when the driver and the passenger are sitting up straight and
well back in the seats. If you are
reclined, the lap belt may slide past
your hips and apply restraint forces
directly to the abdomen. Therefore, in
the event of a frontal collision, the
risk of personal injury may increase
with increasing recline of the seatback.
Separate and split bench seatNon–split bench seat
2002 MY TACOMA_U (OM35786U)
25
3. DRIVER’S SEAT CUSHION ANGLE
ADJUSTING KNOB (on some models)
Turn the knob either way.
4. DRIVER’S SEAT LUMBAR SUPPORT
ADJUSTING SWITCH (on some
models)
Push the control switch either way.
The amount of lumbar support will
change as long as the switch is
pushed.
’02 Tacoma U (L/O 0109)
—Moving passenger’s seat for
rear seat entry
(Xtra–cab models)
CAUTION
After putting back the seat, try
pushing the seat forward and rearward to make sure it is secured in
place.
Never allow anyone to rest their
foot on the press pedal while the
vehicle is moving.
For easy access to the rear seat, do
this.
1. Lift the seatback angle adjusting lever
or press the pedal behind the seatback.
The seat will slide forward.
2. Move the seat to the front–most position.
After passengers are in, lift up the seatback and return the seat until it locks.
26
2002 MY TACOMA_U (OM35786U)
’02 Tacoma U (L/O 0109)
—Folding seatback
(regular cab models)
Pull the seatback lock release lever and
fold down the seatback.
Hold the lever until you have swung the
seatback forward slightly.
CAUTION
When returning the seatback to the
upright position, observe the following precautions in order to prevent
personal injury in a collision or sudden stop:
Make sure the seatback is securely
locked by pushing forward and rearward on the top of the seatback.
Make sure the seat belts are not
twisted or caught in the seatback
and are arranged in their proper
position and are ready to use.
Swing–up jump seats
(Xtra–cab models)
To raise the bottom cushion, pull it up.
To lower the bottom cushion, push it
down.
See “Luggage stowage precautions” in
Section 2 for precautions in loading luggage.
CAUTION
When returning the bottom cushion to
its original position, make sure the
seat belts are not twisted or caught
under the bottom cushion and are arranged in their proper position and
are ready to use.
2002 MY TACOMA_U (OM35786U)
27
Folding rear seatback (double
cab models)
Pull the seatback lock release belt forward and fold down the seat back.
’02 Tacoma U (L/O 0109)
CAUTION
When returning the seatback to the
upright position, observe the following precautions in order to prevent
personal injury in a collision or sudden stop:
Make sure the seatback is securely
locked by pushing forward and rearward on the top of the seatback.
Failure to do so will prevent the
seat belt from operating properly.
Make sure the seat belts are not
twisted or caught in the seatback
and are arranged in their proper
position and are ready to use.
You can use the rear seatback tray when
the vehicle is stopped.
CAUTION
28
To avoid serious injury:
Do not set up the rear seatback
tray while the vehicle is moving.
Do not sit on the folded rear seat-
back tray.
2002 MY TACOMA_U (OM35786U)
NOTICE
To prevent the seat from damaging,
avoid putting heavy loads on the rear
seatback tray.
Head restraints
Front
’02 Tacoma U (L/O 0109)
For your safety and comfort, adjust the
head restraint before driving.
To raise: Pull it up.
To lower: Push it down while pressing the
lock release button.
On some models, you can also move the
head restraint forward or backward. If
such adjustment is desired, pull or push
the head restraint.
The head restraint is most effective when
it is close to your head. Therefore, using
a cushion on the seatback is not recommended.
CAUTION
Adjust the center of the head re-
straint so that it is closest to the
top of your ears.
After adjusting the head restraint,
make sure it is locked in position.
Do not drive with the head re-
straints removed.
Rear (double cab models only)
2002 MY TACOMA_U (OM35786U)
29
Armrest
To use the armrest, do this.
To lower: Pull the lock release strap and
down the armrest.
To raise: Push down the lock release
strap and up the armrest.
NOTICE
To prevent damage to the armrest,
avoid putting heavy loads on it.
’02 Tacoma U (L/O 0109)
Seat belts—
—Seat belt precautions
Toyota strongly urges that the driver and
passengers in the vehicle be properly restrained at all times with the seat belts
provided. Failure to do so could increase
the chance of injury and/or the severity of
injury in accidents.
Child. Use a child restraint system appropriate for the child until the child becomes large enough to properly wear the
vehicle’s seat belts. See “Child restraint”
for details.
REGULAR CAB MODELS—
If a child is too large for a child restraint
system, the child should sit in the seat
and must be restrained using the vehicle’s
seat belt.
XTRA–CAB and DOUBLE CAB MODELS—
If a child is too large for a child restraint
system, the child should sit in the rear
seat and must be restrained using the
vehicle’s seat belt. According to accident
statistics, the child is safer when properly
restrained in the rear seat than in the
front seat.
If a child must sit in the front seat, the
seat belts should be worn properly. If an
accident occurs and the seat belts are not
worn properly, the force of the rapid inflation of the airbag may cause death or
serious injury to the child.
Do not allow the child to stand up or
kneel on either rear or front seats. An
unrestrained child could suffer serious injury or death during emergency braking or
a collision. Also, do not let the child sit
on your lap. It does not provide sufficient
restraint.
Small–framed person or youth in a
3–point type seat belt. On models with
a bench seat, have a small–framed person
or youth sit slightly closer to the center
of the vehicle (so the shoulder belt does
not cross over the neck). On models with
separate seats, move the seat fully backward.
Pregnant woman. Toyota recommends the
use of a seat belt. Ask your doctor for
specific recommendations. The lap belt
should be worn securely and as low as
possible over the hips and not on the
waist.
Injured person. Toyota recommends the
use of a seat belt. Depending on the injury, first check with your doctor for specific
recommendations
30
2002 MY TACOMA_U (OM35786U)
Loading...
+ 269 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.