Toyota CELICA 1999 Owner Manual

Part 1 OPERATION OF INSTRUMENTS AND CONTROLS—

Chapter 1-1 Overview of instruments and controls

 Instrument panel overview  Instrument cluster overview  Indicator symbols on the

instrument panel

99MY CELICA U

Instrument panel overview

99MY CELICA U

1. Side vents

2. Side defroster outlets

3. Instrument cluster

4. Personal lights

5. Electric moon roof switches and interior lights

6. Glove box

7. Power door lock switches

8. Power window switches

9. Ashtray

10. Cup holder

11. Parking brake lever

12. Manual transmission gear shift lever or automatic transmission selector lever

13. Lower vent

14. Hood lock release lever

15. Power rear view mirror control switch (with power windows)

99MY CELICA U

1. Headlight and turn signal switch

2. Wiper and washer switches

3. Emergency flasher switch

4. Clock

5. Center vents

6. Car audio

7. Auxiliary box

8. Air conditioning controls

9. Rear window defogger switch

10. Liftback— Power rear view mirror control switch (without power windows) Convertible— Convertible top control switch and quarter window control switches

11. Cigarette lighter

12. Ignition switch

13. Cruise control switch

14. Tilt steering lock release lever

15. Instrument panel light control knob

Instrument cluster overview

99MY CELICA U

1. Service reminder indicators and indicator lights

2. Tachometer

3. Odometer

4. Engine coolant temperature gauge

5. Fuel gauge

6. Trip meter

7. Trip meter reset knob

8. Speedometer

Indicator symbols on the instrument panel

(type A)

(type B)

Brake system warning light

Seat belt reminder light

Discharge warning light

Low oil pressure warning light

∗

99MY CELICA U

∗

Open door warning light

SRS airbag warning light

Turn signal indicator lights

Headlight high beam indicator light

Overdrive- off indicator light

∗

(type A)

(type B)

∗

Malfunction indicator lamp

Low fuel level warning light

∗

Anti- lock brake system warning light

∗

Cruise control indicator light

∗

: For details, see ”Service reminder indicators and warning

buzzers” in Chapter 1- 5.

∗

: If this light flashes, see ”Cruise control” in Chapter 1-6.

∗

99MY CELICA U

Part 1 OPERATION OF INSTRUMENTS AND CONTROLS—

Chapter 1-2 Keys and Doors

 Keys  Side doors  Power windows  Trunk lid/Back door  Hood  Fuel tank cap  Electric moon roof  Convertible top

Keys

Your vehicle is supplied with two kinds of key.

1. Master key—This key works in every lock.

2. Sub key—This key is for side doors.

To protect things locked in the glove box, trunk or luggage compartment when you have your vehicle parked, leave the sub key with the attendant.

Since the side doors, trunk lid and back door can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.

KEY NUMBER PLATE Your key number is shown on the plate.

Keep the plate in a safe place such as your wallet, not in the vehicle.

If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number.

We recommend you to write down the key number and keep it in safe place.

Side doors

99MY CELICA U

LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn

it.

To lock: Turn the key forward. To unlock: Turn the key backward.

Both side doors lock and unlock simultaneously with either side door. In the driver’s door lock, turning the key once will unlock the driver’s door and twice in succession will unlock both side doors simultaneously.

LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB

Move the lock knob.

To lock: Push the knob forward. To unlock: Pull the knob backward.

Closing the side door with the lock knob in the lock position will also lock the side door. Be careful not to lock your keys in the vehicle.

Vehicles with a power door lock system—The side door cannot be locked if you leave the key in the ignition switch.

Driver’s side

Passenger’s side

LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH

Push the switch.

To lock: Push the switch on the front side. To unlock: Push the switch on the rear side.

Both side doors lock or unlock simultaneously.

CAUTION

Before driving, be sure that the side doors are closed and locked, especially when small children are in the vehicle. Along with the proper use of seat belts, locking the side doors helps prevent the driver and passengers from being thrown out from the vehicle during an accident. It also helps prevent the side doors from being opened unintentionally.

Power windows— —Power window precautions

CAUTION

To avoid serious personal injury, you must do the following.

 Always make sure the head, hands

and other parts of the body of all occupants are kept completely inside the vehicle before you close the power windows. If someone’s neck, head or hands gets caught in a closing window, it could result in a serious injury. When anyone closes the power windows, be sure that they operate the windows safely.

 When small children are in the ve-

hicle, never let them use the power window switches without supervision. Use the window lock button to prevent them from making unexpected use of the switches.

 Never leave small children alone in

the vehicle, especially with the ignition key still inserted. They could use the power window switches and get trapped in a window. Unattended children can become involved in serious accidents.

99MY CELICA U

—Side windows

The windows can be operated with the switch on each side door.

The power windows work when the ignition switch is in the ”ON” position.

Key off operation: If both side doors are closed, they work for 60 seconds even after the ignition switch is turned off. They stop working when either side door is opened.

OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as

long as you hold the switch. To open: Lightly pull down the switch.

To close: Push up the switch.

Automatic operation (to open only): Pull the switch completely down and then release it. The window will fully open. To stop the window partway, lightly push the switch up and then release it.

OPERATING THE PASSENGER’S WINDOW

Use the switch on the passenger’s door. The driver’s door also has a switch that controls the passenger’s window.

The window moves as long as you hold the switch.

To open: Pull down the switch. To close: Push up the switch.

If you push in the window lock button on the driver’s door, the passenger’s window cannot be operated.

Convertible models—The window lock button also locks the quarter windows.

99MY CELICA U

For front passenger’s use

Window lock button

For driver’s use

99MY CELICA U

—Quarter windows (convertible)

The windows can be operated with switches on the center console.

The windows move as long as you hold the switch.

To open: Push on the lower side of the switch. To close: Push on the upper side of the switch.

Trunk lid (convertible)/ Back door (liftback)—

CAUTION

 Keep the trunk lid or back door

closed while driving. This not only keeps the luggage from being thrown out but also prevents exhaust gases from entering the vehicle.

 Lift back only: If the lock has been

half latched, the battery power will be weaken.

To open the trunk lid or back door from the outside, insert the master key and turn it clockwise.

See ”Luggage stowage precautions” in Part 2 for precautions to observe for loading luggage.

To close the trunk lid, lower it and press down on it. To close the back door, lower it hardly.

After closing the trunk lid or back door, try pulling it up to make sure it is securely closed and make sure that the interior lights and open door warning light are turned off.

99MY CELICA U

—Lock release lever

To open the trunk lid or back door from the driver’s seat, pull up on the lock release lever.

—Luggage security system

This system deactivates the lock release lever so that things locked in the trunk or luggage compartment can be protected.

1. Liftback: Push down the security lock levers to lock the rear seatbacks.

After locking the rear seatbacks, try folding them down to make sure they are securely locked, otherwise someone could get into the trunk or luggage compartment by folding down a rear seat.

2. After closing the trunk lid or back door, insert the master key and turn it counterclockwise to deactivate the lock release lever.

After closing the trunk lid or back door, try pulling it up to make sure it is securely locked.

Hood

99MY CELICA U

To open the hood:

1. Pull the hood lock release lever. The hood will spring up slightly.

CAUTION

Before driving, be sure that the hood is closed and securely locked. Otherwise, the hood may open unexpectedly while driving and an accident may occur.

2. In front of the vehicle, pull up the auxiliary catch lever and lift the hood.

3. Hold the hood open by inserting the support rod into the slot.

Before closing the hood, check to see that you have not forgotten any tools, rags, etc. and return the support rod to its clip—this prevents rattles. Then lower the hood and make sure it locks into place. If necessary, press down gently on the front edge to lock it.

CAUTION

After inserting the support rod into the slot, make sure the rod supports the hood securely from falling down on to your head or body.

Fuel tank cap

99MY CELICA U

CAUTION

 Make sure the cap is tightened se-

curely to prevent fuel spillage in case of an accident.

 Use only a genuine Toyota fuel tank

cap for replacement. It has a builtin check valve to reduce fuel tank vacuum.

1. To open the fuel filler door, pull the lever up.

When refueling, turn off the engine.

CAUTION

 Do not smoke, cause sparks or al-

low open flames when refueling. The fumes are flammable.

 When opening the cap, do not re-

move the cap quickly. In hot weather, fuel under pressure could cause injury by spraying out of the filler neck if the cap is suddenly removed.

2. To remove the fuel tank cap, turn the cap slowly counterclockwise, then pause slightly before removing it. After removing the cap, hang it on the cap hanger.

It is not unusual to hear a slight swoosh when the cap is opened. When installing, turn the cap clockwise till you hear a click.

If the cap is not tightened securely, the malfunction indicator lamp comes on. Make sure the cap is tightened securely.

The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.

Electric moon roof

Sliding operation

Tilting operation

To operate the moon roof, use the switches beside the interior light.

The moon roof works when the ignition switch is in the ”ON” position. However, if both side doors are closed, it works for 60 seconds even after the ignition switch is turned off. It stops working when either side door is opened.

Sun shade operation— The sun shade can be opened or closed

by hand. Sliding operation— To open: Push the switch on the ”SLIDE”

side. The sun shade will be opened together

with the roof. To close: Push the switch on the opposite

side of the ”SLIDE” side. As a precaution when closing, the roof

stops at the half closed position before fully closing. Therefore, release the switch and then push it again to close it completely.

Tilting operation— To tilt up: Push the switch on the ”UP”

side. To lower: Push the switch on the opposite side of the ”UP” side.

99MY CELICA U

You may stop the moon roof at any desired position. The roof will move while the switch is being pushed and stop when released.

CAUTION

To avoid serious personal injury, you must do the following.

 While the vehicle is moving, always

keep the head, hands and other parts of the body of all occupants away from the roof opening. Otherwise, you could be seriously injured if the vehicle stops suddenly or if the vehicle is involved in an accident.

 Always make sure nobody places

his/her head, hands and other parts of the body in the roof opening before you close the roof. If someone’s neck, head or hands gets caught in the closing roof, it could result in a serious injury. When anyone closes the roof, first make sure it is safe to do so.

 Never leave small children alone in

the vehicle, especially with the ignition key still inserted. They could use the moon roof switches and get trapped in the roof opening. Unattended children can become involved in serious accidents.

 Never sit on top of the vehicle

around the roof opening.

Convertible top— —Convertible top precautions

CAUTION

 When raising or lowering the con-

vertible top, keep hands clear from the hinges of the top side rails and any part of the top linkage.

 The vehicle should never be driven

with the convertible top partially lowered. Make sure the top has been either fully latched to the windshield frame or fully lowered before driving.

NOTICE



Make sure there are no items or packages between the rear seatback and the convertible top storage area when raising or lowering the convertible top. Even small items may interfere with convertible top operation and can cause damage.



Do not sit or place excessive weight on the convertible top; when the top is up or down, damage to the top may result.

99MY CELICA U



Do not raise or lower the convertible top when the temperature is below 5°C (41°F), or damage to the top material or rear window may result. If necessary to do so, warm the vehicle in a heated garage prior to operating the convertible top mechanism.



Do not lower the convertible top if the top is damp or wet. Possible interior water damage, water stains or mildew of the top material may result.



When the convertible top is completely lowered, keep the rear window defogger turned off to avoid damage to the convertible top.

—Lowering the convertible top

99MY CELICA U

LOWERING THE CONVERTIBLE TOP

The ignition switch must be in the ”ON” position to operate the convertible top.

1. Lower all the side windows, quarter windows, and sun visors. Then pull the latch handles fully backward.

Before operating, make sure the manual control switch is not in the ”MANUAL” position. (See ”If the convertible top does not raise or lower” in Part 4.)

2. Push and hold the convertible top control switch on the ”OPEN” side until the convertible top is completely lowered. Raise the sun visors.

INSTALLING THE TOP BOOT

The top boot is used to cover and conceal the completely lowered convertible top. It is in the trunk, and is stored in a plastic bag.

3. Place the top boot over the lowered convertible top. Then tuck its outer edge under the body moldings.

99MY CELICA U

—Raising the convertible top

4. Secure the top boot snaps to the ones on the quarter trim.

5. Attach the fastener tape on the top boot to that on the rear seatback.

REMOVING THE TOP BOOT

1. Push the top boot backward to separate its fastener tape from the tape behind the rear seatback.

99MY CELICA U

2. Release the top boot snaps from the quarter trim.

3. Pull out the outer edge of the top boot from under the body moldings.

Put the removed top boot in the plastic bag and store it in the trunk.

RAISING THE CONVERTIBLE TOP

The ignition switch must be in the ”ON” position to operate the convertible top.

4. Lower the sun visors. Check that all the side windows and quarter windows are lowered. Then push and hold the convertible top control switch on the ”CLOSE” side until the top touches the windshield frame.

5. Push the latch handles fully forward till they are hooked.

Visually check that the latch handles are fully seated in the strikers. Also, pull on the convertible top side rails to make sure the top is securely hooked.

6. Raise all the side windows, quarter windows, and sun visors.

99MY CELICA U

Part 1 OPERATION OF INSTRUMENTS AND CONTROLS—

Seats

While the vehicle is being driven, all vehicle occupants should have the seatback upright, sit well back in the seat and properly wear the seat belts provided.

CAUTION

99MY CELICA U

Front seats— —Seat adjustment precautions

Adjust the driver’s seat so that the foot pedals, steering wheel and instrument panel controls are within easy reach of the driver.

CAUTION

Chapter 1-3 Seats, Seat belts, Steering wheel and Mirrors

 Seats  Front seats  Fold- down rear seat  Head restraints  Seat belts  SRS driver and front

passengerairbags

 Child restraint  Tilt steering wheel  Outside rear view mirrors  Anti- glare inside rear viewmirror

 Do not drive the vehicle unless the

occupants are properly seated. Do not allow sitting on top of a folded- down seatback, or in the luggage compartment. Persons not properly seated and not property restrained by seat belts can be severely injured in the event of emergency braking or a collision.

 During driving, do not allow pas-

sengers to stand up or move around between seats. Severe injuries can occur in the event of emergency braking or a collision.

 Adjustments should not be made

while the vehicle is moving, as the seat may unexpectedly move and cause the driver to lose control of the vehicle.

 When adjusting the seat, be careful

not to hit the seat against a passenger or luggage.

 After adjusting the seat position,

try sliding it forward and backward to make sure it is locked in position.

 After adjusting the seatback, exert

body pressure to make sure it is locked in position.

 Do not put objects under the seats.

The objects may interfere with the seat- lock mechanism or unexpectedly push up the seat position adjusting lever; the seat may suddenly move, causing the driver to lose control of the vehicle.

 While adjusting the seat, do not put

your hands under the seat or near the moving parts. You may jam your hands or fingers.

—Adjusting front seats

99MY CELICA U

1. SEAT POSITION ADJUSTING LEVER

Pull the lever up. Then slide the seat to the desired position with slight body pressure and release the lever.

SEATBACK ANGLE ADJUSTING

LEVER

Lean forward and pull the lever up. Then lean back to the desired angle and release the lever.

CAUTION

To reduce the risk of sliding under the lap belt during a collision, avoid reclining the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the driver and the passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen. Therefore, in the event of a frontal collision, the risk of personal injury may increase with increasing recline of the seatback.

3. DRIVER’S SEAT CUSHION ANGLE ADJUSTING KNOB

Turn the knob either way.

99MY CELICA U

—Moving passenger’s seat for rear seat entry

CAUTION

 After putting back the seat, try

pushing the seat forward and rearward to make sure it is secured in place.

 Never allow anyone to rest their

foot on the release pedal while the vehicle is moving.

For easy access to the rear seat, do this.

1. Lift the seatback angle adjusting lever or press the pedal behind the seatback.

The seat will slide forward.

2. Move the seat to the front-most position.

After passengers are in, lift up the seatback and return the seat until it locks.

99MY CELICA U

Fold- down rear seat (liftback)

1. Pull up the seatback security lock lever 1 to the unlock position.

2. Pull up the lock release button 2.

3. Fold down the seatback.

Each seatback may be folded separately. This will enlarge the luggage compartment

as far as the front seatbacks. See ”Luggage stowage precautions” in Part 2 for precautions to observe for loading luggage.

Head restraints

CAUTION

When returning the seatback to the upright position:

 Make sure the seat belts are not

twisted or caught in the seatback and are arranged in their proper position and are ready to use.

 Make sure the seatback is securely

locked by pushing forward and rearward on the top of the seatback.

For your safety and comfort, adjust the head restraint before driving.

To raise: Pull it up. To lower: Push it down while pressing the lock release button.

On some models, you can also move the head restraint forward or backward. If such adjustment is desired, pull or push the head restraint.

The head restraint is most effective when it is close to your head. Therefore, using a cushion on the seatback is not recommended.

CAUTION

 Adjust the center of the head re-

straint so that it is closest to the top of your ears.

 After adjusting the head restraint,

make sure it is locked in position.

 Do not drive with the head re-

straints removed.

Seat belts— —Seat belt precautions

Toyota strongly urges that the driver and passengers in the vehicle be properly restrained at all times with the seat belts provided. Failure to do so could increase the chance of injury and/or the severity of injury in accidents.

Child. Use a child restraint system appropriate for the child until the child becomes large enough to properly wear the vehicle’s seat belts. See ”Child restraint” for details.

If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.

If a child must sit in the front seat, the seat belts should be worn properly. If an accident occurs and the seat belts are not worn properly, the force of the rapid inflation of the airbag may cause death or serious injury to the child.

Do not allow the child to stand up or kneel on either rear or front seats. An unrestrained child could suffer serious injury or death during emergency braking or a collision. Also, do not let the child sit on your lap. It does not provide sufficient restraint.

99MY CELICA U

Pregnant woman. Toyota recommends the

use of a seat belt. Ask your doctor for specific recommendations. The lap belt should be worn securely and as low as possible over the hips and not on the waist.

Injured person. Toyota recommends the use of a seat belt. Depending on the injury, first check with your doctor for specific recommendations.

CAUTION

Persons should ride in their seats properly wearing their seat belts whenever the vehicle is moving. Otherwise, they are much more likely to suffer serious bodily injury or death in the event of sudden braking or a collision.

When using the seat belts, observe the following:

 Use the belt for only one person at

a time. Do not use a single belt for two or more people—even children.

 Avoid reclining the seatbacks too

much. The seat belts provide maximum protection when the seatbacks are in the upright position. (Refer to the seat adjustment instructions.)

 Be careful not to damage the belt

webbing or hardware. Take care that they do not get caught or pinched in the seat or side doors.

 Inspect the belt system periodically.

Check for cuts, fraying, and loose parts. Damaged parts should be replaced. Do not disassemble or modify the system.

 Keep the belts clean and dry. If

they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive cleaners—they may severely weaken the belts. (See ”Cleaning the interior” in Part 5.)

 Replace the belt assembly (includ-

ing bolts) if it has been used in a severe impact. The entire assembly should be replaced even if damage is not obvious.

 Front passenger’s seat only—Re-

place the belt if the warning label under the sleeve can be seen. The warning label, ”REPLACE BELT”, will appear if the belt receives a severe impact or other force.

99MY CELICA U

—Seat belts

Adjust the seat as needed (front seats only) and sit up straight and well back in the seat. To fasten your belt, pull it out of the retractor and insert the tab into the buckle.

You will hear a click when the tab locks into the buckle.

The seat belt length automatically adjusts to your size and the seat position.

The retractor will lock the belt during a sudden stop or on impact. It also may lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around freely.

99MY CELICA U

If the seat belt cannot be pulled out of the retractor, firmly pull the belt and release it. You will then be able to smoothly pull the belt out of the retractor.

When a passenger’s shoulder belt is completely extended and is then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system securely. (For details, see ”Child restraint” in this chapter.) To free the belt again, fully retract the belt and then pull the belt out once more.

CAUTION

 After inserting the tab, make sure

the tab and buckle are locked and that the belt is not twisted.

 Do not insert coins, clips, etc. in

the buckle as this may prevent you from properly latching the tab and buckle.

 If the seat belt does not function

normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.

Ta k e u p slack

To o h i g h

Keep as low on hips as possible

Adjust the position of the lap and shoulder belts.

Position the lap belt as low as possible on your hips—not on your waist, then adjust it to a snug fit by pulling the shoulder portion upward through the latch plate.

CAUTION

 High- positioned lap belts and

loose- fitting belts both could cause serious injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.

 For your safety, do not place the

shoulder belt under your arm.

—Seat belt extender

If your seat belt cannot be fastened securely because it is not long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.

Please contact your local Toyota dealer so that the dealer can order the proper required length for the extender. Bring the heaviest coat you expect to wear for proper measurement and selection of length. Additional ordering information is available at your Toyota dealer.

99MY CELICA U

 Remember that the extender pro-

vided for you may not be safe when used on a different vehicle, or for another person or at a different seating position than the one originally intended for.

To release the belt, press the buckle- release button and allow the belt to retract.

If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it retracts.

CAUTION

When using the seat belt extender, observe the following. Failure to follow these instructions could result in less effectiveness of the seat belt restraint system in case of vehicle accident, increasing the chance of personal injury.

 Never use the seat belt extender if

you can fasten the seat belt without it.

To connect the extender to the seat belt, insert the tab into the seat belt buckle so that the ”PRESS” signs on the buckle- release buttons of the extender and the seat belt are both facing outward as shown.

You will hear a click when the tab locks into the buckle.

When releasing the seat belt, press on the buckle- release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and extender itself.

When not in use, remove the extender and store in the vehicle for future use.

CAUTION

 After inserting the tab, make sure

the tab and buckle are locked and that the seat belt extender is not twisted.

 Do not insert coins, clips, etc. in

the buckle as this may prevent you from properly latching the tab and buckle.

 If the seat belt does not function

normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.

99MY CELICA U

SRS driver and front passenger airbags

The SRS (Supplemental Restraint System) airbags are designed to provide further protection for the driver and front passenger when added to the primary protection provided by the seat belts.

In response to a severe frontal impact, the SRS airbags work together with the seat belts to help prevent or reduce injury by inflating, in order to decrease the likelihood of the driver’s or front passenger’s head or chest directly hitting the steering wheel or dashboard. The passenger airbag is activated together with the driver airbag, even with no passenger in the front seat.

Be sure to wear your seat belt.

CAUTION

A driver or front passenger too close to the steering wheel or dashboard during airbag deployment can be killed or seriously injured. Toyota strongly recommends that:

 The driver sit as far back as pos-

sible from the steering wheel while still maintaining control of the vehicle.

 The front passenger sit as far back

as possible from the dashboard.

 All vehicle occupants be properly

restrained using the available seat belts.

This indicator comes on when the ignition key is turned to the ”ACC” or ”ON” position. It goes off after about 6 seconds. This means the SRS airbags are operating properly.

This warning light system monitors the front airbag sensors, airbag sensor assembly, inflators, warning light, interconnecting wiring and power sources. (For details, see ”Service remainder indicators and warning buzzers” in Chapter 1- 5.)

99MY CELICA U

The SRS airbag system is designed to activate in response to a severe frontal impact within the shaded area between the arrows in the illustration.

There may be the case that the SRS airbags will not activate with such an impact in which the occupant wearing the seat belt correctly would not get serious injury.

The SRS airbags will deploy if the severity of the impact is above the designed threshold level, comparable to an approximate 20 km/h (14 mph) collision when impacting straight into a fixed barrier that does not move or deform.

+ 175 hidden pages

Toyota CELICA 1999 Owner Manual

Specifications and Main Features

Frequently Asked Questions

User Manual