Toyota AVALON 2005 Owners Manual
AVALON_Navi_U (L/O 0501)
Foreword
Thank you for your purchase of the Navigation System. Please read this manual carefully to ensure proper use. Keep this
manual stored in your vehicle at all times.
The Toyota Navigation System is one of the most technologically advanced vehicle accessories ever developed. The system receives
satellite signals from the Global Positioning System (GPS) operated by the U. S. Department of Defense. Using these signals and other
vehicle sensors, the system can show you where you are and assist you in locating a desired destination.
The navigation system is designed to select efficient routes from your present starting location to your destination. The system is
designed to direct you to a destination that is unfamiliar to you in an efficient manner. The system uses the maps of DENSO based on
NAVTEQ maps, GDT maps and infoUSA POIs. The calculated routes are neither the shortest routes nor routes without traffic congestion. Your own personal local knowledge or “short cut” may at times be faster than the calculated routes.
The navigation system’s database includes about 50 point of interest categories to allow you to easily select destinations such as
restaurants and hotels. If a destination is not in the database, you can enter the street address or a major intersection close to it and
the system will route you there. The system will provide both a visual map and audio instructions. The audio instructions will announce
the distance and direction to go when you are approaching a fork or intersection. These voice instructions will help you keep your eyes
on the road and are timed to provide enough time to allow you to maneuver, change lanes or slow down.
Please be aware that all current vehicle navigation systems have certain limitations that may affect their ability to perform
properly. The accuracy of the vehicle’s position depends on the satellite condition, road configuration, vehicle condition or
other circumstances. For more information on the limitations of the system, refer to pages 44 through 46.
E 2005 TOYOTA MOTOR CORPORATION
All rights reserved. This material may not be reproduced or copied, in
whole or in part, without the written permission of Toyota Motor Corporation.
i
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
AVALON_Navi_U (L/O 0501)
Important information about this manual
For safety reasons, this manual indicates
items requiring particular attention with the
following marks.
CAUTION
This is a warning against anything
which may cause injury to people if
the warning is ignored. You are informed about what you must or must
not do in order to reduce the risk of
injury to yourself and others.
NOTICE
This is a warning against anything
which may cause damage to the vehicle or its equipment if the warning
is ignored. You are informed about
what you must or must not do in
order to avoid or reduce the risk of
damage to your vehicle and its equipment.
INFORMATION
This provides additional information.
Initial screen
When you start the engine or when the
ignition switch is set to the ACC, the
initial “TOYOTA” screen appears and the
system begins operating.
CAUTION
When the vehicle is stopped with
the engine running, always apply the
parking brake for safety.
After a few seconds, the “CAUTION”
screen appears.
ii
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
Please read it and follow the instructions.
If a screen other than for the navigation
system is displayed, the current screen
would change to the “CAUTION” screen
by pushing the
“MAP/VOICE”,
“MENU” or “DEST” button on the
navigation controller.
When you push the
on the navigation controller to indicate
“I agree” on the display, the next
screen appears.
On this screen, you can select the language shown on the screen. Select your
desired switch on the screen.
“Eng”: English
“Fr”: French
You can also select the language by the
following procedure.
“ENTER” button
AVALON_Navi_U (L/O 0501)
1. Push the “INFO” button. Select the
“Language” switch to display the
“CAUTION” screen.
2. Select your desired language and
push the
“Eng”: English
“Fr”: French
3. Select
the
“ENTER” button.
“I agree” switch and push
“ENTER” button.
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
iii
AVALON_Navi_U (L/O 0501)
Safety Instruction
To use your system as safely as possible,
follow all the safety tips shown below.
This system is intended to assist you in
reaching your destination and, if used
properly, can do so. You, as the driver,
are solely responsible for the safe operation of your vehicle and the safety of your
passengers.
Do not use any feature of this system to
the extent it distracts you from safe driving. Your first priority while you are driving
should always be the safe operation of
your vehicle. While you are driving, be
sure to observe all traffic regulations.
Before attempting to use this system while
you are driving, learn how to use it and
become thoroughly familiar with it. Read
the entire “Navigation System Owner’s
Manual” to make sure you understand the
system. Do not allow others to use this
system until they have read and understood these and other instructions in this
manual.
For your safety, some functions may become inoperable when you start driving.
Unavailable switches are dimmed. You can
input your destination and select your
route only when the vehicle is not moving.
CAUTION
D For safety, the driver should not
operate the navigation system while
he/she is driving. Inattention to the
road and traffic may cause an accident.
D While you are driving, be sure to
follow the traffic regulations and
keep the road condition in mind. If
a traffic sign on the road has been
changed, route guidance may provide wrong information such as the
direction of a one way street.
While you are driving, listen to the voice
instructions as much as possible and
glance at the screen briefly and only when
it is safe. However, do not totally rely on
voice guidance. Use it just for your information. If the system cannot determine
your current position correctly, there is a
possibility of incorrect, late or non−voice
guidance.
iv
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
The data in the system may occasionally
be incomplete. Road conditions, including
driving restrictions (no left turns, street
closures, etc.) frequently change. Therefore, before you follow any instruction
from the system, look to see whether you
can comply with the instruction safely and
legally.
This system cannot warn you about such
things as the safety of an area, condition
of streets, and availability of emergency
services. If you are unsure about the
safety of an area, do not drive into it.
Under no circumstances is this system
a substitute for the driver’s personal
judgement.
Use this system only in locations where
it is legal to do so. Some countries/provinces may have laws prohibiting video
screens within sight of the driver.
AVALON_Navi_U (L/O 0501)
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
v
Display, symbols and switches
North−up or heading−up symbol and
scale of map
Indicates a map view with north up or
heading up. The figure also indicates
the map scale. For details, see page
41.
Clock
The digital clock
indicates the time. For
details, see page 112.
Distance and time t o destination
Displays the distance and the
estimated travel time to the
destination. The direction will be
indicated when your vehicle is off
the route. For details, see page 25.
Current vehicle position mark
To indicate the current position,
see page 30 for details.
Operation guid e
To display the switch
function on each screen.
viii
Changing the map
Changing the map
direction
When the dual screen is displayed, the
left screen can be switched to “North−
up”/“Heading−up”.
Display of Point of
Interest
Symbols such as restaurants and hotels,
etc. can be displayed on the screen. For
details, see page 37.
Changing the route
guidance
When you select this switch, the “Change
route” screen will appear. For details, see
page 25.
Quick Registration
of marked point
To register the current vehicle position as
a marked point. For details, see page 73.
direction and Po int
of Interest display
on the right screen
When the map display is shown on the
dual screens, select this to call out the
editing menu (screen) on the right screen.
Heading−up symbol
and scale of map
On the map, the vehicle travel direction is
up. The red arrow indicates the north.
Speech command
system indicator
This indicator appears on the screen to
indicate that the speech command system
is on. For the operation of the speech
command system and the speech command list, see pages 116 and 120.
INFORMATION
D The display may be tinged in purple
due to the reflection of sunlight, but
this is not a malfunction.
D The displayed image may become
darker and moving images may be
slightly distorted when the display
is cold.
D Under extremely cold conditions,
the map may not be displayed and
the data input b y a user may be deleted. Also, the display may take
time to change.
ix
Controller and buttons
“CLIMATE” button
Push this button to
display the “Air
Conditioner” screen.
For details about
controlling the air
conditioning system,
see the separate
“Owner’s Manual”.
“AUDIO” button
Push this button to
display the audio screen.
For details about
controlling the audio
system, see the separate
“Owner’s Manual”.
“MAP/VOICE”
button
Push this button to
repeat a guidance
voice, cancel the
map scroll and start
a guidance. For
details, see page
30.
“ENTER” button/select and scroll lever
In case of selecting the function and
letters or moving cursor, press down the
lever to one direction out of 8 directions.
In case of deciding the function after
selecting it on the screen, push down on
the lever as a button.
Zoom in/out button
These buttons
magnify or reduce
the map scale. For
details, see page
41.
“BACK” button
Push this button
when to call out the
screen just before.
“DEST” button
Push this button to
display the
destination screen.
For details, see
page 4.
“MENU” button
Push this button to
display the menu
screen. This screen
allows you to make
adjustments or
correct settings of
various options and
functions.
“DISP” button
Push this button to
display the
adjustment screen.
For details, see
page 115.
“INFO” button
Push this button to
display the
“Information Menu”
screen. For details,
see page 99.
x
AVALON_Navi_U (L/O 0501)
SECTION I
BASIC FUNCTIONS
Descriptions of basic operations in frequent use
Your navigation system 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inputting letters and numbers 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to move the cursor 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Destination input Explains 11 ways to input your destination 4. . . . . . .
Explains 11 ways to input your destination
Entering destination 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Route guidance screen 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guidance screen 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map appearance 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current position display 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice guidance 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical voice guidance prompts 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Registration of your home 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Detour setting 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying points of interest 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn list 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Map scale 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen scrolling 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Orientation of the map 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limitations of the navigation system 44. . . . . . . . . . . . . . . . . . . . . . . . . . .
Map database information and updates 47. . . . . . . . . . . . . . . . . . . . . . . .
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
1
Your navigation system
AVALON_Navi_U (L/O 0501)
Your navigation system can be operated
by the navigation controller when the
ignition switch is set at ACC or ON.
To access the navigation controller—
Push the lid to open.
To turn on the navigation display—
Push the
“DEST” or “INFO” button.
To turn off the navigation display—
Push the
the
For details, see “Controller and buttons”
on page x.
z To prevent the battery from being
z Do not place heavy objects on the
“MAP/VOICE”, “MENU”,
“DISP” button and select
“SCREEN OFF”.
NOTICE
discharged, do not leave the navigation system on longer than necessary when the engine is not running.
controller.
Inputting letters and
numbers—
To input letters and/or numbers, move
the select and scroll lever to the 8 directions, and when the letter or number
you wish to input is lit up, push the
“ENTER” button. A beep sound is
heard, and the letter or number is input. Repeat this procedure to input the
name or number, etc.
If you type a wrong letter, delete it with
the switch. Selecting the switch
erases one letter.
2
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
Selecting the “List” switch on the
screen, the screen will be changed to display the database items that match the
name or address that you have entered
on the screen. The number of matching
items is shown to the right side of the
screen. If the matching item is more than
9,999, the system displays “::::” on
the screen.
Selecting the
the diacritics input screen, the
switch to display the numeral input
screen.
Selecting the “A−Z” switch changes the
screen back to the alphabet input screen.
“ ” switch to display
“0−9”
AVALON_Navi_U (L/O 0501)
When a list is displayed, you can scroll
the list by using select and scroll lever.
This expresses a displayed
screen position.
If a or a appears to the right
or left of the item name, the
complete name is too long for
the display. Select the or
switch, and the name will scroll
to the end or beginning of its
name.
How to move the cursor
1. Move the cursor to the desired
point by operating the select and
scroll lever. When you release the
lever, scrolling stops.
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
3
AVALON_Navi_U (L/O 0501)
Destination input
Push the
tion controller and the “Destination” screen
appears.
“DEST” button on the naviga-
2. In case of making the position indicated by the cursor
play as a destination, push
button of the navigation
TER”
controller and select your desired
switch on the switch menu on the
right of the screen.
on the dis-
“EN-
4
The destination screen allows you to select the country to be searched for your
destination.
To shift to the next or previous
page.
Select the “Change” switch on the
screen to display a map of the United
States divided into 10 regions and a
part of Canada.
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
Select an area by the select and scroll
lever to select the search area and the
destination screen returns.
Once you choose the region of the country to search, you can use one of 11
different methods to enter your destination.
AVALON_Navi_U (L/O 0501)
United States of America
Idaho
Oregon
US1
Washington
California
US2
Nevada
Arizona
Colorado
Montana
US3
New Mexico
Utah
Wyoming
Iowa
Kansas
Minnesota
Missouri
US4
Nebraska
North Dakota
South Dakota
US5
US6
US7
Oklahoma
Te xa s
Illinois
Indiana
Kentucky
Michigan
Ohio
Wisconsin
Alabama
Arkansas
Louisiana
Mississippi
Tennessee
Connecticut
Maine
Massachusetts
New Hampshire
US8
New Jersey
New York
Rhode Island
Vermont
Delaware
Maryland
New Jersey
Pennsylvania
US9
Virginia
Washington, D.C.
West Virginia
Florida
Georgia
US10
North Carolina
South Carolina
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
5
AVALON_Navi_U (L/O 0501)
CANADA
Alberta
British Columbia
Manitoba
New Brunswick
Newfoundland and Labrador
Nova Scotia
CAN
Ontario
Prince Edward Island
Québec
Saskatchewan
Yukon Territory
You can find your destination using various methods. See pages 7 through 22
for the detailed steps.
1. By “Address”: You can input the
house number and the street address
by using the input keys. See page 7
for the detailed steps.
2. By “POI” (Point of Interest): You can
select one of the many points of interest that have been already stored in
the system’s database. There are 54
categories to choose from including
restaurants, hotels and so on. See
page 11 for the detailed steps.
3. By “Marked points”: You can select
your own favorite destinations as
“Marked points”. The system allows
you to store up 100 marked points.
See page 17 for the detailed steps.
4. By “Previous destination”: You can
select a destination from any of the
last 20 previously set destinations. See
page 18 for the detailed steps.
5. By “Emergency”: You can select one
of the three points of emergency service points that have been already
stored in the system’s database. See
page 18 for the detailed steps.
6. By “Intersection”: You can enter the
names of two intersecting streets. This
is helpful if you do not know the specific street address of your destination
but know the general vicinity. See page
19 for the detailed steps.
7. By “Prev. start point”: You can enter
a point where the system has started
to guide last time. See page 21 for the
detailed steps.
8. By “Freeway Ent./Exit”: You can enter
the name of the freeway (interstate)
entrance or exit. See page 20 for the
detailed steps.
9. By Map Selection: You can select a
destination simply by selecting the
location on the displayed map. See
page 22 for the detailed steps.
10. By Preset Destination (
switches on the “Destination”
screen): You can choose the destina-
tion by selecting one of the preset destination switch. In this case, it is necessary to register your desired
destination beforehand. See page 22
for the detailed steps.
11. By Home (
tination” screen): You can select your
own home without entering the address
each time. In this case, it is necessary
to register your home beforehand. See
page 22 for the detailed steps.
switch on the “Des-
—
6
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
AVALON_Navi_U (L/O 0501)
Destination input by
ADDRESS
INFORMATION
D When inputting the destination, the
response to t he switch may be s low.
D “Points of interest” registration is
made based on the NAVTEQ
“Standard POI Inclusion List” and
infoUSA POI data.
D If there is no point registered,
switches such as “Marked point”,
“Home”, “Previous destination” or
“Previous starting point” are
dimmed and not available.
D The route for returning may not be
the same as that for going.
D The route guidance to the destina-
tion may not be the shortest route
or a route without traffic congestion.
D Route guidance may not be avail-
able if there is no road data for the
specified locat ion.
D When setting the destination, you
should use the map on a scale of
one half mile or smaller.
D To select an “Address”, “POI”,
“Freeway Ent./Exit” or “Intersection” in a different region, a search
area’s change is necessary.
CAUTION
While you are driving, be sure to follow traffic regulations and keep the
road condition in mind. If a traffic
sign on the road has been changed,
the route guidance may provide
wrong information.
There are 2 ways to input a destination
by address.
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
7
(a) Inputting a street name
Select the “Address” switch on the
“Destination” screen. The “Address”
screen appears, and then you can input
a house number.
AVALON_Navi_U (L/O 0501)
After inputting a house number, select the
“OK” switch which you can input a
street name.
It is possible to input a street name first.
Select the
play to display the screen which you can
input a street name.
8
“Street” switch on the dis-
After each letter is inputted, the system
searches the database for street names
that match. Alphabet keys are dimmed if
the database does not have a match for
the next letter in the remaining list of
matching street names.
Selecting the
the diacritics input screen, the
switch to display the numeral input
screen.
Based on your input, the number of
matching sites appears at the top right of
the screen. After the number decreases to
some extent, select the
display the street selection list. If the
number of matches decreases to 4 or
less, the screen changes automatically to
the selection list.
“ ” switch to display
“0−9”
“List” switch to
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
When you find your desired street
name, select
screen changes and displays the map
location of the selected destination and
the route preference. (See “Entering
destination” on page 23.)
If the same street exists in more than one
city, the current screen changes to the
“Select city” screen. Select or enter your
desired city.
of the item. The
AVALON_Navi_U (L/O 0501)
(b) Inputting a city name
The screen for selecting the last 5 towns
appears if you select the
on the “Address” screen on page 7.
“City” switch
If you input a street name first, the screen
changes. You can then input the house
number.
If the above screen appears, you can select an address range on that screen.
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
5 cities are displayed on the screen.
Select the
The current screen changes to the
screen which is for inputting a street
name.
of the desired city name.
9
NOTICE
Under the initial condition, town name
will not be displayed.
“All cities”: All cities are selected.
“Near 5 cities”: 5 near cities are dis-
played. Selecting a city in the list changes
to the display to input a street name.
“Input city name”: The screen for inputting the city name appears.
The screen for inputting a city name appears if you select the
name”
switch on the “Address” screen.
“Input city
AVALON_Navi_U (L/O 0501)
Input the city name.
After the number decreases to some
extent, select the
play the city selection list. If the number of matches decreases to 4 or less,
the screen changes automatically to the
selection list.
“List” switch to dis-
Select the of the desired city
name.
“Map”: If you select this switch, the
screen changes and displays the map
location of the selected city and the route
preference. (See “Entering destination” on
page 23.)
The current screen changes to the
screen which is for inputting a street
name.
10
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
AVALON_Navi_U (L/O 0501)
Input a street name. (See “(a) Inputting
a street name” on page 8.)
The screen changes and displays the
map location of the selected destination
and the route preference. (See “Entering destination” on page 23.)
Destination input by
POI (Point of Interest)
There are 3 ways to select a point of
interest location (POI).
(a) Input the name of the point of inter-
est directly.
(b) Inputting a city name first.
(c) Selecting from the points of interest
categories.
It will not take a long time for you to
find your destination if you use a combination of the searching ways of (a),
(b) and (c).
(a) Input the name of the
point of interest directly
Select the
switch on the “Destination” screen.
The “POI” (Point of Interest) screen appears, and then you can input the name
of the point of interest.
Select letters on the screen to input a
name.
Selecting the
the diacritics input screen, the
switch to display the numeral input
screen.
If the number of sites becomes 4 or less,
or if you select the
bottom right of the screen, the screen
changes and displays a list of sites.
“POI” (Point of Interest)
“ ” switch to display
“0−9”
“List” switch at the
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
11
Select the of your desired destination.
You can search it more easily with the
“City” and “Category” switches.
(See (b) Inputting a city name and (c)
Selection from the point of interest categories.)
AVALON_Navi_U (L/O 0501)
(b) Inputting a city name
Select the
(Point of Interest) screen.
5 cities are displayed on the screen.
Select the
The current screen changes to the
screen which is for inputting a name of
point of interest.
Under the initial condition, town name
will not be displayed.
“City” switch on the “POI”
of the desired city name.
INFORMATION
“Input city name”: The screen for inputting the city name appears.
Input the city name.
If the number of sites becomes 4 or less,
or if you select the
bottom right of the screen, the screen
changes and displays the selection list.
Select the
After entering the city name, input the
name of the point of interest.
“List” switch at the
of the desired city name.
12
“All cities”: All cities are selected.
“Near 5 cities”: 5 near cities are dis-
played. Selecting a city in the list changes
to the display to input the name of the
point of interest.
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
(c) Selection from the point of
interest categories
Select the “Category” switch on the
“POI” (Point of Interest) screen.
AVALON_Navi_U (L/O 0501)
The categories are shown on the
screen. When you select the
your desired category, more detailed
categories are shown.
of
When you select the of your desired category, the screen changes and
displays the previous screen.
“All” categories: You can select the point
of interest by the name in all categories.
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
Once you have selected a category, select
letters directly on the screen to input a
name.
Selecting the
the diacritcs input screen, the
switch to display the numeral input
screen.
If the number of sites becomes 4 or less,
or if you select the
bottom right of the screen, the screen
changes and displays a list of sites.
“ ” switch to display
“0−9”
“List” switch at the
13
AVALON_Navi_U (L/O 0501)
When you select the of your desired item, the screen changes and displays the map location of the selected
destination and the route preference.
(See “Entering destination” on page
23.)
14
In case of having some POIs of the same
name, this screen appears.
“Name sort”: Select this switch to list the
categories in alphabetical order.
“Dist. sort”: Select this switch to list the
categories in order of nearest place from
your current location.
INFORMATION
The information on the desired point
of interest can be displayed on the
map screen.
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
Select the “Info.” switch to display the
selected destination name, address and
telephone number.
List of points of interest
RESTAURANT
AVALON_Navi_U (L/O 0501)
CONTINENTAL
RENTAL CAR AGENCY
JAPANESE
CHINESE
FRENCH
ITALIAN
OTHER
AMERICAN
MEXICAN
SEAFOOD
SHOPPING
GROCERY STORE
GAS STATION
PARKING GARAGE/HOUSE
PARKING LOT
TOYOTA DEALERSHIPS
LEXUS DEALERSHIPS
AUTOMOBILE CLUB
AUTO SERVICE &
MAINTENANCE
HOTEL
GOLF COURSE
SKI RESORT
15
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
AVALON_Navi_U (L/O 0501)
AMUSEMENT PARK
SPORTS COMPLEX
CASINO
MARINA
TOURIST ATTRACTION
WINERY
CITY HALL
POLICE STATION
LIBRARY
HOSPITAL
PARK/RECREATION
CIVIC/COMMUNITY CENTER
CONVENTION/EXHIBITION
CENTER
COURT HOUSE
TRAIN STATION
AIRPORT
BUS STATION
COMMUTER RAIL STATION
FERRY TERMINAL
PARK & RIDE
REST AREA
TOURIST INFORMATION
HISTORICAL MONUMENT
PERFORMING ARTS
16
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
MUSEUM
BANK
SCHOOL
ATM
AVALON_Navi_U (L/O 0501)
Destination input by MARKED
POINTS
Selecting the “Marked points”
switch on the “Destination” screen displays your list of registered marked
points. (Refer to pages 68 through 72
on “Registering”, “Editing” or “Deleting” marked points.)
Sort by “Icon”: Select this switch to list
the marked points by using the registered
icon. There are 46 icons and 4 sound
icons. (For details, see page 70.)
Sort by “Date”: Select this switch to list
the marked points in order of registered
date.
Sort by “Name”: Select this switch to list
the marked points in alphabetical order.
HIGHER EDUCATION
BUSINESS FACILITY
CITY CENTER/NAMED
PLACE
When you select the of your desired item, the screen changes and dis-
plays the map location of the selected
destination and the route preference.
(See “Entering destination” on page
23.)
Then, select the
the route guidance. This new destination
will not be registered as a marked point
or alter the location of the marked point.
There are 3 ways to list the marked point
by selecting switches.
“Enter” switch to start
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
17
AVALON_Navi_U (L/O 0501)
Destination input by
PREVIOUS DESTINATION
Select the “Previous destination”
switch on the “Destination” screen.
The screen lists to 20 previously set destinations.
Select your desired destination. The
screen changes and displays the map
location of the selected destination and
the route preference. (See “Entering
destination” on page 23.)
You can delete the list of previous destinations while you stop your vehicle if
you no longer need them. (See page 83
for details.)
Destination input by
EMERGENCY
By selecting the
switch on the “Destination” screen, the
display changes to a screen to select
police stations, hospitals or dealers.
During driving, only nearby police stations, hospitals or dealers are shown.
The current position is shown with an
address, the latitude and the longitude
at the top of the screen.
When you select your desired emergency
category, the selected emergency category
list is displayed.
“Emergency”
The distance from your current position up
to the destination is displayed on the right
of the name.
You can see the names of the emergency
destinations in alphabetical order by selecting the
screen.
Select the
The screen changes and displays the
map location of the selected destination
and the route preference. (See
ing destination” on page 23.)
Select the
selected emergency destination name, address and telephone number.
“Name sort” switch on the
of your desired item.
“Enter-
“INFO” switch to display the
18
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
INFORMATION
In an area which has not been registered for route guidance, the navigation does not guide. (See pages 46
and 47.)
AVALON_Navi_U (L/O 0501)
Destination input by
INTERSECTION
Select the “Intersection” switch on
the “Destination” screen.
Input the name of the two intersecting
streets which are located near the destination to be set.
When you select the
the number of sites becomes 4 or less,
the list of matching street names appears.
“List” switch or
Select the of your desired item.
After inputting the two intersecting
streets, the screen changes and displays the map location of the selected
destination and the route preference.
(See “Entering destination” on page
23.)
19
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
EMV3111U
If the same two streets cross at more
than one intersection, the screen changes
and displays the menu to select the city
name where the streets intersect. Select
the city and the map location of the selected destination and the route preference. (See “Entering destination” on page
23.)
AVALON_Navi_U (L/O 0501)
Destination input by
FREEWAY ENTRANCE or EXIT
To input a freeway entrance or exit, select the
switch on the “Destination” screen.
Be sure to use the complete name of the
freeway or highway, including the hyphen,
when entering the destination. Freeways
and interstates use an “I” (I−405). US
highways use the state designation before
the number (CA−118).
As the number of matching freeways decreases, you can select the
switch to display the list. When the number of sites becomes 4 or less, the list
screen appears automatically.
“Freeway Ent./Exit”
“List”
Choose the desired freeway by selecting the
You can then select either a freeway
.
“Entrance” or “Exit”.
20
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
Select the of your desired entrance
or exit name. The screen changes and
displays the map location of the selected destination and the route preference. (See “Entering destination” on
page 23.)
AVALON_Navi_U (L/O 0501)
There are 2 ways to list the freeway
entrance or exit.
“Dist. sort”: Select this switch to list the
entrances or exits in order of distance
from your current location.
“Name sort”: Select this switch to list the
entrances or exits in alphabetical order.
Destination input by
PREVIOUS STARTING POINT
Select the
switch on the “Destination” screen.
The screen changes and displays the
map location of the previous starting
point and the route preference. (See
“Entering destination” on page 23.)
If you have not used the navigation yet,
you can not set the destination by the
“Prev. start point”
“Prev. start point” switch.
21
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
AVALON_Navi_U (L/O 0501)
Destination input by MAP Destination input by HOME
Select the “Map” switch on the “Destination” screen.
Destination input by
PRESET DESTINATION
The screen change and displays the
map location of the last map and the
route preference. (See “Entering destination” on page 23.)
22
Select the “ (home)” switch on
the destination input screen.
The screen changes and displays the
map location of your home and the
route preference. (See “Entering destination” on page 23.)
The screen changes to display the map
location of your home about 3 seconds,
and then the system starts to search the
way to your home.
If you have not registered your home yet,
you can not set the destination by the
“ (home)” switch.
For the steps to register or delete your
home, see page 34.
2005 AVALON Navigation from Nov. ’04 Prod. (OM41410U)
Select one of the — switches
on the “Destination” screen, the screen
changes and displays the map location
of your desired preset destination. In
this case, it is necessary to register
your desired preset destination beforehand. (Refer to pages 74 through 76,
“Registering”, “Editing” or “Deleting”
preset destination.)
Loading...