TOTOLINK N600 User Manual

Quick Installation Guide

600Mbps Wireless N Router

Suitable for: N600R

V1.1602

Copyrights TOTOLINK All rights reserv ed. Website: http://www.totolink.net

Information in this document is subject to change without prior notice.

Hardware Installation

Wall Socket

ADSL Modem

Telephone

Cable

Network

Cable

If you use ADSL Modem to access the Internet, please follow below steps. For houses that there is only one
Ethernet cable from the wall, please plug the Ethernet cable to the router’s WAN port directly.

LED Indicators

Red

The router is working under normal power.

The Turbo switch is enabled and the router is working

Green

under middle power.

Blink

The router is working normally or resetting.

Power is off.

Off

The WAN port is connected, the Internet is available.

On

Off

The WAN port is not connected, the Internet is unavailable.

On

There is device connected to LAN port 1/2/3/4.

No device connected to LAN port 1/2/3/4.

Off

Connect with the power adapter

Connect to ADSL modem or Internet Cable

WAN

Connect to PC or Laptop

LAN

Press for 1s, WPS enabled; press for more than 5s, Reset
function enabled.

Improve the router’s working power, extend Wi-Fi coverage.

Router

Status

WAN

Wall Socket

LAN

Ports and Buttons Description

DC IN

RST/WPS

Turbo

NOTE:

1. Please disconnect the power adapter and all cables during
thunderstorm weather;

2. Keep away from heat source and keep well ventilated;

Network

Cable

3. Please pay attention to the waterproofing and moisture-proof
when storing, transporting and running.

4. The power adapter must be original or approved by TOTOLINK.

5. Put the router in flat places.

Set Up PC

Windows Vista/7

Click Start— Control Panel— Network
and Internet— Network Connection,
right-click Local Area Connection,
and choose Properties.

For Windows Vista or Windows 7 Operating System, please comply with following steps to set up.

Double-click Internet Protocol
Version 4 (TCP/IPv4).

Choose Obtain an IP address automatically
and Obtain DNS server address automatically,
click OK; And then click OK.

Windows 10

Click Start( )---All apps---Windows System

---Control Panel---Network and Sharing Center

---Change adapter setting, right-click Local Area
Connection, and choose Properties.

For Windows 10 Operating System, please comply with following steps to set up.

Double-click Internet Protocol
Version 4 (TCP/IPv4).

Choose Obtain an IP address automatically
and Obtain DNS server address automatically,
click OK; And then click OK.

Set Up Router

Please set up the router following below steps.

Run any Web browser.

The USER LOGIN page will pop up automatically. Enter admin for both
User Name and Password, click LOGIN. (The auto pop-up page only for
first connection, future Login please enter “192.168.0.1” in address bar)

7

admin

Wireless Settings, you can change or retain your SSID (wireless network name).

Choose the encryption type. The WPA2-PSK is recommended, then type
in your password ( password length more than 8 characters).Then click
Apply to save the Settings.

Try any website to test the Internet. Here we type in www.totolink.net.

10

4

FAQ

How to reset the router to default settings?

1. Please make sure your router’s power is on regularly, then press the
RST/WPS button for about 5~8s.

2. Loosen the button until your router’s LED lights all flashing, then you
have reset your router to default settings.

What can I do if I forget the router’

s Web Login page User

Name and Password?

Please reset your router to default settings firstly, the default IP address is

192.168.0.1, both default User Name and Password are admin .

How Turbo switch improve the router

3

performance?

By default, the T
router's output power will decrease by about 6dBm theoretically, which
means your Wi-Fi signal will be weakened as well as the Wi-Fi range.
So we recommend you turn it off to reduce radiation only if there is any
pregnant women or infants at home.

urbo switch is on. If you slide the Turbo switch to off, the

’s wireless

Now you can see the Easy Setup interface.

Choose the WAN Connection Type and enter the parameters
provided by your Internet Service Provider.

Here we take PPPoE as example. You are required to enter the User
Name and Password.

Wait for a while, Internet connected successfully! Please click finish.

8

Now the router’s Status interface turns up, it shows connected type

9

and IP address & DNS you get.

Auto Pop-up Setting page for First Wi-Fi
Devices Connection

Click Settings Wi-Fi.

Select TOTOLINK N600R, no password
required by default.

N600R

Note: This function is only suitable for iPhone and a few Android smart phones. If the auto
pop-up page not turns up on your phone, please use PC to set up your router.

→

N600R

When connected, the Web
page of TOTOLINK N600R
will pop up automatically.

N600R

NOTE:

After you set the Key, please remember your SSID and the Key to connect with
your wireless LAN.

WPS: press for about 1~3 seconds, the system LED indicator keep solid
light, it means WPS working;
RST: press for about 5~8 seconds, all LEDs blinks quickly, the device will
restore to factory default settings.

FCC warning:

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following

measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body.

For more information, please go to www.totolink.net