Totolink A3100R User Manual

Quick Installation Guide

AC1200 Wireless Dual Band Gigabit Router

Models: A3100R

Hardware Installation

Default SSIDs

2.4G: TOTOLINK_A3100R
5G: TOTOLINK_A3100R_5G

iPad

Smart Phone

Wall Socket

LEDs

Blink every

CPU

(Front panel)

WAN

LAN

Ports and button

DC IN port

LAN1/2 port

one second

Blinking quickly

Blinking

Connect to an electrical outlet with the supplied power adapter.

Connect to PCs or switches with Ethernet cables.

On

Off

On

Off

The power is on.

The router finishes the booting process and is
working normally.

When the reset process is being proceeded.

The power is off.

The WAN port is connected to an Ethernet port
on a Modem or the wall.

The WAN port is disconnected from an Ethernet
port on a Modem or the wall.

The WAN port is sending or receiving data.

LAN 1/2 port is connected to a computer.On

LAN 1/2 port is disconnected from a computer.Off

LAN 1/2 port is sending or receiving data.Blinking

Copyrights © 2017 TOTOLINK. All Rights Reserved. Website:http://www.totolink.net
Information in this document is subject to change without prior notice.

V1.0 | 2017.11.30

Configure the Router

Run any Web browser. Enter 192.168.0.1 in the address bar.

http://192.168.0.1/

Enter admin for both User Name and Password, then click LOGIN.

admin

PC

Router

GPON Terminal

Network

Cable

DescriptionConnection TypeNO.

No configuration, simply connect the WAN port to existing
Ethernet port by cable.

You’re required to enter IP Address, Subnet Mask, Default
Gateway and DNS information provided by your ISP.

You’re required to enter User Name and Password provided
by your ISP.

TOTOLINK_A3100R_5G

Network

Cable

DHCPA

Static IPB

PPPoEC

A.DHCP. After choose DHCP, you can go on with the 5GHz & 2.4GHz
Wireless Settings.

WAN port

RST/

WPS button

3. Please pay attention to the waterproofing and moisture-proof

when storing, transporting and running.

4. Please use the power adapter provided with the router.

B.Static IP. If you choose Static IP, please enter IP Address, Subnet
Mask, Default Gateway and DNS information provided by your ISP.

Connect to an Ethernet port on a Modem or the wall for Internet
access.

Enable WPS function: when the router is powered on, press and
hold this button for 1~3 seconds until the front panel CPU LED
turns solid on.

Reset to factory defaults: when the router is powered on, press
and hold for 5 seconds or more until the CPU LED blinks quickly.

Now you can see the Easy Setup page. All basic settings could be done
here, including Internet Settings and 5GHz & 2.4GHz Wireless
Settings.

Configure the Router

5G Wireless Settings. You could customize your 5GHz wireless
Network Name(SSID) and Password. The WPA/WPA2-PSK is

5

recommended for Encryption.

TOTOLINK_A3100R

Internet Settings. Connection Status shows physical connection
of router’s WAN port. Choose one Connection Type according to your
ISP(Internet Service Provider).

Wait for a few seconds, the router’s Status interface turns up, showing all

7

connection information.

NOTE:

1. Please disconnect the power adapter and all cables during thunderstorm

weather;

2. Keep away from heat source and keep well ventilated;

Connect Wireless Network

After router settings, please follow below steps to connect wireless network:

Click or icon on the right bottom of your desktop:

1

C.PPPoE. If you choose PPPoE, please enter the User Name and
Password provided by your ISP.

[e-mail]

●●●●●●●●●●●●●●●

Choose the SSID that you have set on Configure the Router. Enter

2

correct password. Click Connect or Next.

TOTOLINK_A3100R_5G

TOTOLINK

2.4G Wireless Settings. Verify or change your 2.4GHz wireless Network
Name(SSID) and Password. The WPA/WPA2-PSK is

6

recommended for Encryption. Click Apply.

TOTOLINK_A3100R

TOTOLINK

Connection Status PPPoE, Connected

Connection Time 0day，0hour，0minute，0second

IP Address 164.126.106.178

Subnet Mask 255.255.255.255

Default Gateway 164.126.96.1

DNS Server 202.96.134.133

MAC Address F4:28:53:00:01:84

NOTE:

We recommend that you remember your Wi-Fi network name and password
for future use.

Enable WPS function: when the router is powered on, press and hold this
button for 1~3 seconds until the front panel CPU LED turns solid on.

Reset to factory defaults: when the router is powered on, press and hold
for 5 seconds or more until the CPU LED blinks quickly.

TOTOLINK_test1

TOTOLINK_test2

TOTOLINK_test3

TOTOLINK_test4

TOTOLINK_A3100R_5G

TOTOLINK_A3100R

TOTOLINK_test5

TOTOLINK_test1

TOTOLINK_test2

TOTOLINK_A3100R_5G

TOTOLINK_A3100R

Connect Wireless
Network

Wireless network connected. Enjoy your Wi-Fi☺.

3

TOTOLINK_A3100R_5G
Connected, secured

TOTOLINK_A3100R

TOTOLINK_test1

TOTOLINK_test2

TOTOLINK_test3

TOTOLINK_test4

TOTOLINK_test5

For Mobile device users, please go to Settings—Wi-Fi to connect wireless
network.

4

1

1.Check your computer’s IP address, make sure it is set to “Obtain an IP
address automatically”. Steps: right click Network—Properties—Change

adapter settings---Local Area Connection—Properties—Internet
Protocol Version 4(TCP/IPv4).

2.Make sure you enter the correct default access: 192.168.0.1. Try again.

3.Use another web browser and try again.

4.Reboot your router and try again.

2

1.Check the Internet status by connecting a computer directly to the modem
via Ethernet cable. If it is not working properly, contact your Internet
Service Provider.

2.Setup your router again according to part 2 Configure the Router.

3.Reboot your cable modem (if have) and router, then try again.

3

Keep the router powered on, press and hold the RST/WPS button for 5
seconds or more until the front panel CPU LED blinks quickly. It will restore
to factory default settings.

4

In case you changed your router’s Login User Name and Password, we
suggest you reset your router to factory default settings by above operations.
Then use the following parameters to login the router’s Web interface:

Default IP address: 192.168.0.1, User Name: admin, Password: admin

5

By default, TOTOLINK router don’t have any wireless network password.
If you have set one, please log in to router’s Web Management page, go
to 5G Wireless---Basic Settings or 2.4G Wireless --- Basic
Settings to obtain or reset your password.

FAQ

What can I do if the login page does not appear?

What can I do if I cannot access the Internet?

How to reset the router to factory default Settings?

What can I do if I forget the router’s Web login User Name
and Password?

What can I do if I forget my wireless network Password?

(Frequently Asked Questions)

5

FCC warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
the equipment.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment should be installed and operated with minimum distance
20cm between the radiator& your body.

NOTE:

5150-5250MHz is restricted for indoor use only in all EU member states.

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However,there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception,which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following

Measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

AT BE

CY CZ

FR DE EL HU IE IT LV

LT LU MT NL PL PT

SI ES SE

DK EE FI

UK

BG

RO

SK
HR

For more information, go to www.totolink.net.