TOTOLINK A3002RU User Manual

Quick Installation Guide

AC1200 Wireless Dual Band Gigabit Router

Suitable for: A3002RU

V1.15.11

Copyrights by TOTOLINK All rights reserved. Website: http://www.totolink.net

Information in this document is subject to change without prior notice.

Hardware Installation

Telephone Wire

Telephone

Wire

Network

Cable

Telephone

Wire

If you access Internet by ADSL, please comply with step 1, 2, 3 and 4 in below diagram in correct order; if you access Internet by
residential broadband, please comply with step 2, 3 and 4 to connect the WAN port of your router with the residential broadband directly.

LED Indicators

POWER

CPU

2.4G

5G

1/2/3/4LAN

USB

This indicator lights blue when the router powered on, otherwise it is off.

When the router powered on, this indicator keeps lighting blue.

This indicator lights blue when the 2.4G wireless connection enabled.

This indicator lights blue when the 5G wireless connection enabled.

When the WAN port is connected successfully the indicator lights blue.

WAN

While transmitting or receiving data through the WAN port the indicator
blinks blue.

When the LAN port has a successful connection, the indicator lights blue.

While transmitting or receiving data through the LAN port the indicator
blinks blue.

This indicator lights blue when you have plugged a USB device on the router.

Router

NOTE:

1. Please disconnect the power adapter and all cables during
thunderstorm weather;

Network

Cable

2. Keep away from heat source and keep well ventilated;

3. Please pay attention to the waterproofing and moisture-proof
when storing, transporting and running.

4. The power supply must reach the rated current and power.

5. Put the router in flat places.

Set Up PC

Windows 7

Right click “Internet” on desktop, choose
“Properties”—Change Adapter Settings,
then right click “Local Area Connection”,
choose “Properties”

For Windows Vista or Windows 7 Operating System, please comply with following steps to set up.

Double-click “Internet Protocol
Version 4 (TCP/IPv4)”

Choose “Obtain an IP address automatically”
and “Obtain DNS server address automatically”,
click “OK”; go back to previous interface and
click “OK”

Windows 8

Click “Start—Control Panel—Network and
Sharing Center—Change adapter setting”,
right-click “Ethernet”, and choose “Properties”.

For Windows 8 Operating System, please comply with following steps to set up.

Double-click “Internet Protocol Version 4
(TCP/IPv4)”.

Choose “Obtain an IP address automatically”
and “Obtain DNS server address automatically”,
click “OK”; go back to previous interface and
click “OK”.

Set Up Router

Please set up the router following below steps.

Run the Web browser.

Type 192.168.1.1 in the Web Browser address bar, then press Enter key.

Input the User Name and Password, then click Login button
(The default Username and Password is admin).

7

Wireless Network Connection

Here we take PPPoE as an example. User Name and Password are
required.

Right-click “My Network
Places”, click “Properties”

Input the encrytion key and click “Connect”

Confirm the wireless network SSID name,
choose one that you would like to connect,
then click “Connect”

For 5G Wireless Settings, you can setup SSID (network name) and
encryption.

Right-click “Wireless Network
Connection”, and click “View
Available Wireless Networks”

Have connected wireless network, you can access
Internet through wireless mode.

Now you have logged into the Easy Setup interface.

Choose the WAN connection type and enter the parameters provided
by your ISP.

By default, no encryption selected. Here WPA2 Mixed is recommended

8

for you to protect your network, then type in your password.

You can setup the 2.4G Wireless Setting referring to 5G Wireless Setting.

9

On this page, you can also enable or disable IPTV. If enable this function,
please enter the VLAN ID and choose correct IPTV port. Then click Apply

10

to save the settings.

Wait for a while, Internet connected successfully! Please click finish.

11

Now the router’s Status interface turns up, it shows connected type and

12

IP address & DNS you get.

5

1. Please make sure your router’s power is on regularly, then press the
RST button for about 10s.

2. Loosen the button until your router’s LED lights all flashing, then you
have reset your router to default settings.

Please reset your router to default settings firstly, and set a new password.
The default Username and Password is admin.
The default IP is 192.168.1.1.

FCC warning:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and(2) this device must accept
any interference received, including interference that may cause undesired operation.

changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.NOTE: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However,there is no guarantee that interference will not occur in a
particular installation.If this equipment does cause harmful interference to radio or television
reception,which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

-- Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
This equipment should be installed and operated with minimum distance 20cm between the
radiator& your body.

FAQ

How to reset the router to default settings?

Forget the password?

For more information, please go to www.totolink.net