Toto TSPTM Installation And Owner's Manual

Warranty Registration and Inquiry
For product warranty registration, TOTO U.S.A. Inc. recommends online warranty registration. Please visit
our web site http://www.totousa.com. If you have questions regarding warranty policy or coverage, please con­tact TOTO U.S.A. Inc., Customer Service Department, 1155 Southern Road, Morrow, GA 30260
[phone] or [phone] when calling from outside of U.S.A.

Installation and Owner’s Manual
Manual de Instrucciones y del Propietario
Manuel d’Installation et d’Utilisation

½” Pressure Balance Valve
Válvula de equilibrio de presión de ½”
Valve d’équilibrage de la pression de ½ “

For Tub Spout installation see instructions on page 3.
Para la instalación del tubo de salida de la bañera, vea las instrucciones

en la página 3.
Pour l’installation du branchement du robinet, consulter les instructions

page 3

TSPTM

2

ENGLISH

TABLE OF CONTENTS

THANKS FOR CHOOSING TOTO!

The mission of TOTO is to provide the world with healthy, hygienic and more
comfortable lifestyles. We design every product with the balance of form and
function as a guiding principle. Congratulations on your choice.

Thanks for Choosing TOTO! .............................................................................. 2

Before Installation ................................................................................................ 2

Warnings ............................................................................................................... 2

Installation Procedure ....................................................................................... 3-4

Maximum Temperature Adjustment .................................................................. 5

Cartridge Replacement ....................................................................................... 6

Warranty................................................................................................................ 7

Rough-In Dimensions ..................................................................................20-21

BEFORE INSTALLATION

 Observe all local plumbing codes.
 Flush all water lines prior to installation.
 Make sure the water supply is shut off.
 Read these instructions carefully to ensure proper installation.

 TOTO reserves the right to update product design without notice.

WARNINGS

For safe operation, please observe the following:

 Use only 1/2” or greater copper tube and one 90° elbow for con-

nection from valve to tub spout.
 Tub spout shall be installed 12”± 1” below valve center.
 The showerhead must be installed 40” or more above valve center.
 Do not install a shut-off device after the valve.
 RISK OF SCALDING: This valve must have the maximum tempera-

ture adjusted after installation (see page 5).

 Recommended operating pressure:

 Minimum pressure.........20 psi (0.14 MPa)

 Maximum pressure........80 psi (0.14 MPa)

 If you are soldering during installastion, do not apply excessive heat to

the valve body. Excessive heat may damage internal components.
 Hot water supply temperature should not exceed 120°F (49°C).
 Do not use this valve at an ambient temperature below 32°F (0°C).
 Insulate the hot water supply pipe to minimize heat loss.
 Do not use steam for the hot water supply.
 Do not disassemble the valve cartridge.

3

ENGLISH

INSTALLATION PROCEDURE

CAUTION: RISK OF PERSONAL INJURY.

When this valve is installed, it must be adjusted to minimize the risk of
scalding. The maximum water temperature should never exceed 120°F (49°C).

If Soldering: Excessive heat when soldering can cause damage to internal
valve components. Use caution not to heat the valve more than necessary
to form a good joint. Removal of the valve cartridge and service stops is not
necessary if excessive heat is avoided. Remove plaster guard if necessary.

1. Shut off the main hot and cold water supply.

2. Install the valve so that the port centers are positioned between
1-11/16” and 2-11/16” [43-68 mm] from the finished wall surface.

3. Connect the hot and cold supply lines to the proper ports, marked “H”
and “C”. For installation with reversed inlets, refer to page 4.

4. Secure the valve to wall framing or blocking using the two unthreaded
mounting ears.

For shower with tub installation:

• See recommended installation dimensions on page 20.

• Plumb the valve’s bottom port (labeled “TUB”) to the tub spout. To ensure

correct operation, the tub spout must be connected to the valve using
1/2” or greater copper tube (12” ± 1” length) and a single 90° elbow.
Do not use PEX or similar materials.

• Plumb the valve’s top port to the showerhead. The showerhead must
be installed 40” or more above valve center.

For shower only installations:

• See recommended installation dimensions on page 20.

• Cap the valve’s bottom port (labeled “TUB”). 1/2” NPT cap not included.

• Plumb the valve’s top port to the showerhead.

5. Follow maximum temperature adjustment procedure (page 5).

6. Replace the plaster guard (if removed during installation) on the valve
until finished wall is complete.

4

ENGLISH

Installation with Reversed Inlets

For back-to-back valve applications, the inlets to one of the valves may be
reversed for ease of installation. The following procedure must be followed
to ensure correct operation of valves installed with reversed inlets.

1. Do not install the valve receiving reversed inlets upside down. The port
labeled “TUB” must face downward for the valve to function properly.

2. On the valve receiving reversed inlets, connect the cold water supply
to the hot port (marked “H”), and the hot water supply to the cold port
(marked “C”)

3. Use a flat bladed screwdriver to shut off the hot and cold water supply at
the service stops on the valve with reversed inlets.

4. Remove the o-ring, temperature stop and bonnet, as shown below.

5. Remove the valve stem, rotate it 180° so that the arrow faces DOWN,
and replace. See figure below.

6. Reinstall the bonnet and restore hot and cold water supply by opening
the service stops.

7. Relabel the ports on the valve to prevent confusion during future service.

8. Follow maximum temperature adjustment procedure (page 5).

INSTALLATION PROCEDURE

ARROW:

- Faces up for standard
installation

- Faces down for reversed
inlet installation

Valve Cartridge

Bonnet

O-Ring

Temperature
Stop

Valve Stem

5

ENGLISH

CAUTION: The maximum temperature setting must be adjusted in the
following situations:

• After initial installation of the valve.

• After servicing or replacing the valve cartridge.

• After any adjustments, replacements, or repairs to equipment
supplying hot water to the valve.

• Seasonally to compensate for temperature variation in the water
supply.

O-Ring

Temperature
Stop

MAXIMUM TEMPERATURE ADJUSTMENT

1. Remove the o-ring.

2. Remove the temperature stop.

3. Monitor water temperature with thermometer and rotate valve stem
counterclockwise until desired water temperature is reached. Do not
set the water temperature above 120° F (49°C).

4. Reinstall the temperature stop so that is touching the bonnet tab,
preventing further counterclockwise rotation of the valve stem.

5. Reinstall the o-ring to secure the temperature stop.

Bonnet Tab

6

ENGLISH

CARTRIDGE REPLACEMENT

1. Use a flat bladed screwdriver to shut off the hot and cold water supply
at the service stops.

2. Remove the o-ring and temperature stop.

3. Unscrew the bonnet and remove valve stem.

4. Use needle nose pliers to remove valve cartridge.

5. Apply silicone grease to new cartridge where indicated and install into
valve body.

6. Replace valve stem with arrow pointing UP (for reversed inlet
installations, arrow should point DOWN), and reinstall bonnet.

7. Restore hot and cold water supply by opening service stops.

8. Follow maximum temperature adjustment procedure on Page 5.

Valve Cartridge

Valve Body

Bonnet

O-Ring

Temperature
Stop

Valve Stem

Service Stops

Grease

7

ENGLISH

WARRANTY

1. TOTO® warrants its residential faucets and bathroom accessories (“Product") to be free from defects in
materials and workmanship during normal use when properly installed and serviced, for the lifetime of
the Product from date of purchase. This limited warranty is extended only to the ORIGINAL PURCHASER
of the Product and is not transferable to any third party, including but not limited to any subsequent
purchaser or owner of the Product. This warranty applies only to TOTO Product purchased and installed
in North, Central and South America.

2. TOTO’s obligations under this warranty are limited to repair, replacement or other appropriate
adjustment, at TOTO’s option, of the Product or parts found to be defective in normal use, provided that
such Product was properly installed, used and serviced in accordance with instructions. TOTO reserves
the right to make such inspections as may be necessary in order to determine the cause of the defect.
TOTO will not charge for labor or parts in connection with warranty repairs or replacements. TOTO is not
responsible for the cost of removal, return and/or reinstallation of the Product.

3. This warranty does not apply to the following items:

a. Damage or loss sustained in a natural calamity such as fire, earthquake, flood, thunder, electrical

storm, etc.

b. Damage or loss resulting from any accident, unreasonable use, misuse, abuse, negligence, or

improper care, cleaning, or maintenance of the Product.
c. Damage or loss resulting from sediments or foreign matter contained in a water system.
d. Damage or loss resulting from improper installation or from installation of the Product in a harsh

and/or hazardous environment, or improper removal, repair or modification of the Product.
e. Damage or loss resulting from electrical surges or lightning strikes or other acts which are not the

fault of TOTO or which the Product is not specified to tolerate.
f. Damage or loss resulting from normal and customary wear and tear, such as gloss reduction,

scratching or fading over time due to use, cleaning practices or water or atmospheric conditions,

including but not limited to, the use of bleach, alkali, acid cleaners, dry (powder) cleaners or any

other abrasive cleaners or the use of metal or nylon scrubbers.

4. In order for this limited warranty to be valid, proof of purchase is required. TOTO encourages warranty

registration upon purchase to create a record of Product ownership at http://www.totousa.com. Product
registration is completely voluntary and failure to register will not diminish your limited warranty rights.

5. If the Product is used commercially or is installed outside of North, Central or South America, TOTO

warrants the Product to be free from defects in materials and workmanship during normal use for one (1)
year from the date of installation of the Product, and all other terms of this warranty shall be applicable
except the duration of the warranty.

6. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS WHICH VARY

FROM STATE TO STATE, PROVINCE TO PROVINCE OR COUNTRY TO COUNTRY.

7. To obtain warranty repair service under this warranty, you must take the Product or deliver it prepaid to

a TOTO service facility together with proof of purchase (original sales receipt) and a letter stating the
problem, or contact a TOTO distributor or products service contractor, or write directly to TOTO U.S.A.,
INC., 1155 Southern Road, Morrow, GA 30260, or call [phone] or [phone], if outside the
U.S.A. If, because of the size of the Product or nature of the defect, the Product cannot be returned to
TOTO, receipt by TOTO of written notice of the defect together with proof of purchase (original sales
receipt) shall constitute delivery. In such case, TOTO may choose to repair the Product at the purchaser’s
location or pay to transport the Product to a service facility.

THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY TOTO. REPAIR, REPLACEMENT
OR OTHER APPROPRIATE ADJUSTMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE
EXCLUSIVE REMEDY AVAILABLE TO THE ORIGINAL PURCHASER. TOTO SHALL NOT BE RESPONSIBLE
FOR LOSS OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES
OR EXPENSES INCURRED BY THE ORIGINAL PURCHASER, OR FOR LABOR OR OTHER COSTS DUE TO
INSTALLATION OR REMOVAL, OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT
SPECIFICALLY STATED ABOVE. IN NO EVENT WILL TOTO’S RESPONSIBILITY EXCEED THE PURCHASE
PRICE OF THE PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTIES, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR USE OR FOR A PARTICULAR
PURPOSE, ARE EXPRESSLY DISCLAIMED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.

8

ESPAÑOL

CONTENIDO

GRACIAS POR ELEGIR A TOTO!

La misión de TOTO es brindarle al mundo estilos de vida sanos, higiénicos y más
cómodos. Diseñamos cada producto con un equilibrio de forma y función como el
principio referente. Felicidades por su elección.

Gracias por elegir a TOTO! ................................................................................ 8

Antes de la instalación ........................................................................................ 8

Advertencias ......................................................................................................... 8

Procedimiento de instalación ........................................................................9-10

Ajuste de temperatura máxima ........................................................................ 11

Reemplazo del cartucho.................................................................................... 12

Garantía .............................................................................................................. 13

Dimensiones preliminares ........................................................................... 20-21

ANTES DE LA INSTALACIÓN

 Siga todos los códigos locales de plomería.
 Vacíe todas las líneas de agua antes de la instalación.
 Asegúrese que el suministro de agua esté apagado.
 Lea estas instrucciones cuidadosamente para asegurar una instalación adecuada.
 TOTO se reserva el derecho de actualizar el diseño del producto sin

previo aviso.

ADVERTENCIAS

Para una operación segura, siga los siguientes puntos:

 Solamente utilice un tubo de cobre de 12 mm (0,5 pulgadas) o más y sola-

mente uno 90° codo para hacer la conexión desde la válvula hasta el tubo de

salida de la bañera.
 No instale un dispositivo de apagado después de la válvula.
 Se instalará surtidor de la tina 305 mm [12 pulgadas] ± 25mm [1 pulgada] por

debajo del centro de la válvula.
 Cabezal de ducha debe estar instalada de 1016mm [40 pulgadas] o más por

encima del centro de la válvula.
 RIESGO DE EBULLICIÓN: Debe ajustarse la temperatura máxima de esta vál-

vula después de la instalación (véase página 11).

 Presión operativa recomendada:

 Presión mínima.........20 psi (0.14 MPa), dinámico

 Presión máxima........80 psi (0.55 MPa), estática

 Si está soldando durante la instalación, no aplique calor excesivo al cuerpo de la

válvula. El calor excesivo puede dañar los componentes internos.
 La temperatura del suministro de agua caliente no debe exceder los 120°F (49°C).
 No utilice esta válvula a una temperatura ambiente por debajo de los 32°F (0°C).
 Aísle la tubería del suministro de agua caliente para minimizar la pérdida de calor.
 No utilice vapor para el suministro de agua caliente.

 No desarme el cartucho de la válvula.