Toshiba SD-K531SU, SD-K531SUA Owner's Manual

2

14

22

29

34

39

Introduction

DIGITAL VIDEO

42

45

55

67

DVD VIDEO PLAYER & VIDEO
CASSETTE RECORDER

SD-K531SUA

OWNER’S MANUAL

©2004 Toshiba Corporation

This device does not tape-record copy protected DVD Video Discs.

Connections

Basic setup

Playback

(VCR)

Recording

(VCR)

Other functions

(VCR)

Basic playback

(DVD)

Advanced

playback

(DVD)

Function setup

(DVD)

Others

J2D81701A (E)COV.p65 8/7/04, 4:23 PM1

2

Introduction

IMPORTANT SAFEGUARDS

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rain

or moisture.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN

BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be deter­mined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Changes or modifications not expressly approved by the partly responsible for compliance with the
FCC Rules could void the user's authority to operate this equipment.

CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CARE­FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTE­NANCE, CONTACT AN AUTHORIZED SERVICE LOCATION.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLO­SURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.
DO NOT STARE INTO BEAM.

The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the presence
of uninsulated dangerous voltage within the product's
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION:

TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.

Location of the required Marking

The rating sheet and the safety caution are on the rear of the unit.

CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE
STANDARDS, 21 CFR SUBCHAPTER J.

J2E50601A (E)p02-13.p65 8/30/04, 5:47 PM2

3

Introduction

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS

The manufacturer of this unit does not make any recommendations for attachments, as they may cause
hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.

8. ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.

8A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation,
to ensure reliable operation of the unit, and to protect it from overheating.
These openings must not be blocked or covered. The openings should never be blocked by placing the unit
on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat
source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and/or the manufacturer’s instructions have been adhered to.

10. POWER SOURCE

This unit should be operated only from the type of power source indicated on the rating plate. If you are not
sure of the type of power supply to your home, consult your appliance dealer or local power company. For
units intended to operate from battery power, or other sources, refer to the operating instructions.

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Instead of the polarized alternating-current line plug, your unit
may be equipped with a 3-wire grounding-type plug (a plug having a third (grounding) pin). This plug will
only fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug
into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of
the grounding-type plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.

S3125A

PORTABLE CART WARNING

(symbol provided by RETAC)

IMPORTANT SAFEGUARDS

J2D81701A (E)p02-13.p65 28/5/04, 1:39 PM3

4

Introduction

IMPORTANT SAFEGUARDS

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the
unit due to lightning and power line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from touching such power lines or circuits,
as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
For example:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those controls

that are covered by the operating instructions, as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the unit to its normal

operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.

21. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.

22. DISC TRAY

Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

23. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's
manual of the other equipment carefully and follow the instructions when making any connections.

J2D81701A (E)p02-13.p65 28/5/04, 1:39 PM4

5

Introduction

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

24. LASER BEAM

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the
laser beam. It may cause sight damage.

25. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and product malfunction.

26. NOTE TO CABLE TV SYSTEM INSTALLER

This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con­nected to the grounding system of the building, as close to the point of cable entry as practical.

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert
the AC cord plug into a standard 120V 60Hz polarized AC outlet.

Notes:

•

Never connect the AC line cord plug to other than the specified
voltage (120V 60Hz). Use the attached power cord only.

•

If the polarized AC cord does not fit into a non-polarized AC
outlet, do not attempt to file or cut the blade. It is the user’s
responsibility to have an electrician replace the obsolete outlet.

•

If you cause a static discharge when touching the unit and the
unit fails to function, simply unplug the unit from the AC outlet
and plug it back in. The unit should return to normal operation.

Polarized AC Cord Plug
(One blade is wider than the other.)

AC Outlet

Wider Hole
and Blade

Power source

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

ANTENNA LEAD IN WIRE

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)

GROUND CLAMP

ELECTRIC SERVICE

EQUIPMENT

NEC-NATIONAL ELECTRICAL CODE
S2898A

IMPORTANT SAFEGUARDS / Power source

J2D81701A (E)p02-13.p65 28/5/04, 1:39 PM5

6

Introduction

Notes on handling

When shipping the DVD/VCR, the original shipping
carton and packing materials come in handy. For
maximum protection, repack the unit as it was
originally packed at the factory.
Do not use volatile liquids, such as insect spray, near
the DVD/VCR. Do not leave rubber or plastic
products to contact the DVD/VCR for a prolonged
period. They will leave marks on the finish.
The top and rear panels of the DVD/VCR may
become warm after a long period of use. This is not a
malfunction.
When the DVD/VCR is not in use, be sure to remove
the disc and the video cassette turn off the power.
If you do not use the DVD/VCR for a long period, the
unit may not function properly in the future. Turn on
and use the DVD/VCR occasionally.

Notes on locating

Place the DVD/VCR on a level surface. Do not use it
on a shaky or unstable surface such as a wobbling
table or inclined stand. The loaded disc or the video
tape may become dis-aligned and damage the DVD/
VCR.
When you place this DVD/VCR near a TV, radio, or
VCR, the playback picture may become poor and the
sound may be distorted. In this case, place the DVD/
VCR away from the TV, radio, or VCR.

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent
solution, wring well and wipe. Use a dry cloth to wipe
it dry.
Do not use any type of solvent, such as thinner and
benzine, as they may damage the surface of the
DVD/VCR.
If you use a chemical saturated cloth to clean the unit,
follow that product’s instructions.

To obtain a clear picture

The DVD/VCR is a high technology, precision device. If
the video head, the head drum, the optical pick-up lens
or disc drive parts are dirty or worn down, the picture
quality will deteriorate. To obtain a clear picture, we
recommend regular inspection and maintenance
(cleaning or parts replacement) every 1,000 hours of
use depending on the operating environment. For
details, contact your nearest dealer.

Notes on moisture condensation

Moisture condensation damages the DVD/VCR.
Please read the following carefully.

Moisture condensation occurs, for example, when you
pour a cold drink into a glass on a warm day. Drops of
water form on the outside of the glass. In the same way,
moisture may condense on the head drum or the optical
pick-up lens inside this unit, one of the most crucial
internal parts of the DVD/VCR.

Moisture condensation occurs during the
following cases.

When you bring the DVD/VCR directly from a cold
place to a warm place.
When you use the DVD/VCR in a room where you
just turned on the heater, or a place where the cold
wind from the air conditioner directly hits the unit.
In summer, when you use the DVD/VCR in a hot and
humid place just after you move the unit from an air
conditioned room.
When you use the DVD/VCR in a humid place.

Do not use the DVD/VCR when moisture
condensation may occur.

If you use the DVD/VCR in such a situation, it may
damage discs and internal parts. Remove the disc or
the video tape, connect the power cord of the DVD/
VCR to the wall outlet, turn on the DVD/VCR, and
leave it for two or three hours. After two or three
hours, the DVD/VCR will have warmed up and
evaporated any moisture. Keep the DVD/VCR
connected to the wall outlet and moisture
condensation will seldom occur.

Precautions

E

x

a

m

p

l

e

o

f

m

o

i

s

t

u

r

e

c

o

n

d

e

n

s

a

t

i

o

n

!

Tape

Head drum

It’s too

warm!

Wait!

Wall outlet

J2D81701A (E)p02-13.p65 28/5/04, 1:39 PM6

7

Introduction

Notes on discs

On handling discs

Do not touch the playback side of the disc.

Do not attach paper or tape to discs.

On cleaning discs

Fingerprints and dust on the disc cause picture and
sound deterioration. Wipe the disc from the center
outwards with a soft cloth. Always keep the disc
clean.

If you cannot wipe off the dust with a soft cloth, wipe
the disc lightly with a slightly moistened soft cloth and
finish with a dry cloth.
Do not use any type of solvent such as thinner,
benzine, commercially available cleaners or antistatic
spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight
or near heat sources.
Do not store discs in places subject to moisture and
dust such as a bathroom or near a humidifier.
Store discs vertically in a case. Stacking or placing
objects on discs outside of their case may cause
warping.

Playback side

DVD video disc

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

Track 1 Track 2 Track 3 Track 4 Track 5

Structure of disc contents

Normally, DVD video discs are divided into titles, and
the titles are sub-divided into chapters. VIDEO CDs and
audio CDs are divided into tracks.

DVD video disc

Video CD/Audio CD

Each title, chapter or track is assigned a number, which
is called “title number”, “chapter number” or “track
number” respectively.
There may be discs that do not have these numbers.

Notes on copyright

It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, and rent copyrighted
material without permission.

This device does not tape-record copy protected DVD
Video Discs.
The device is not to be used for copying copyrighted
content without the express written permission of the
copyright owner.
Obtaining such permission is the sole responsibility of
the user.

This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights
owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology
must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is
prohibited.

Video CD/Audio CD

J2D81701A (E)p02-13.p65 28/5/04, 1:39 PM7

8

Introduction

DIGITAL VIDEO

About this owner’s manual

This owner’s manual explains the basic instructions of
this DVD/VCR. Some DVD video discs are produced in
a manner that allows specific or limited operation during
playback. As such, the DVD/VCR may not respond to all
operating commands. This is not a defect in the DVD/
VCR. Refer to instruction notes of discs.

“

” may appear on the TV screen during operation.

A “

” means that the operation is not permitted by the

DVD/VCR or the disc.
For example, sometimes it is unable to stop the
playback of copyright message of the disc when the
STOP (

) button is pressed. Alternatively, the “ ” may

also indicate that the feature is not available for the disc.

Notes on region numbers

The region number of this DVD/VCR is 1. If region
numbers, which stand for their playable area, are printed
on your DVD video disc and you do not find

1

or

ALL

,
disc playback will not be allowed by the player. (In this
case, the DVD/VCR will display a message on-screen.)

On Video CDs

This DVD/VCR supports Video CDs equipped with the
PBC (Version 2.0) function. (PBC is the abbreviation of
Playback Control.) You can enjoy two playback
variations depending on types of discs.

• Video CD not equipped with PBC function

(Version 1.1)

Sound and movie can be played on this DVD/VCR in
the same way as an audio CD.

• Video CD equipped with PBC function

(Version 2.0)

In addition to operation of a Video CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using the
menu displayed on the TV screen (Menu Playback).
Some of the functions described in this owner’s
manual may not work with some discs.

Playable discs

This DVD/VCR can play the following discs.

• You cannot play discs other than those listed above.

• You cannot play discs of DVD-RAM, DVD-ROM,

Photo CD, etc., or non standardized discs even if they
may be labeled as above.

• Some CD-R/RWs cannot be played back depending
on the recording conditions.

• This DVD/VCR uses the NTSC color system, and
cannot play DVD video discs recorded in any other
color system (PAL, SECAM, etc.).

Notes on discs (continued)

DVD
video
discs

Disc Mark

Contents

Disc
Size

Maximum

playback time

Video
CDs

Approx. 4 hours

(single sided disc)

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

Approx. 160 minutes

(double sided disc)

Approx. 74 minutes

Approx. 20 minutes

8 cm

12 cm

8 cm

12 cm

Audio

+

Video

(moving

pictures)

Audio

+

Video

(moving

pictures)

Audio
CDs

Approx. 74 minutes

Approx. 20 minutes

8 cm

(CD

single)

12 cm

Audio

The following discs are also available.

DVD-R/RW discs of DVD video format
CD-R/CD-RW discs of CD-DA, Video CD, SVCD,
MP3, WMA or JPEG format
Kodak Picture CD and FUJICOLOR CD format

Some of these discs may be incompatible.

J2D81701A (E)p02-13.p65 28/5/04, 1:39 PM8

9

Introduction

IMPORTANT SAFEGUARDS .......................... 2

Power source ...................................................5

Precautions ......................................................6

Notes on discs..................................................7

Contents. .......................................................... 9

Identification of controls ................................. 10

Antenna connections......................................14

Cable TV connections ....................................16

Connecting to a TV ........................................ 18

Connecting to optional equipment..................20

Introduction

Recording a TV program ................................ 34

One-touch Timer Recording (OTR) ................ 36

Timer recording .............................................. 37

Recording (VCR)

Stereo recording and playback ...................... 39

Second Audio Program (SAP)........................ 39

Duplicating a video tape ................................. 40

Recording a DVD/CD disc.............................. 41

Other functions (VCR)

Loading and unloading a cassette tape ......... 29

Cassette tape playback .................................. 30

Special playback ............................................ 31

Convenience function..................................... 32

Playback (VCR)

Setting the video channel ............................... 22

Setting the language ...................................... 23

Clock setting................................................... 24

Tuner setting .................................................. 27

Basic setup

Playing a disc ................................................. 42

Basic playback (DVD)

MP3/WMA/JPEG playback ............................ 45

Zooming ......................................................... 50

Locating desired scene .................................. 50

Marking desired scenes ................................. 51

Repeat playback ............................................ 52

A-B Repeat playback ..................................... 52

Program playback (CD).................................. 53

Random playback (CD) .................................. 53

Changing angles ............................................ 54

Title selection ................................................. 54

DVD menu...................................................... 54

Advanced playback (DVD)

Language code list ......................................... 67

Troubleshooting ............................................. 68

Specifications ................................................. 69

Limited warranty ............................................. 70

Others

Contents

Connections

Function setup (DVD)

Changing soundtrack language ..................... 55

Setting surround sound .................................. 55

Setting subtitles .............................................. 56

Karaoke playback........................................... 56

E.B.L. (Enhanced Black Level) ...................... 57

Setting the aspect ratio of TV screen ............. 58

Setting on screen display ............................... 59

Status display of disc ..................................... 59

Dynamic Range Control ................................. 60

Parental control setting .................................. 61

To change the parental level .......................... 62

Temporary disabling of rating level by DVD disc ..

63

Setting OSD language ................................... 64

Setting language ............................................ 65

Selecting PROGRESSIVE scan..................... 66

J2D81701A (E)p02-13.p65 28/5/04, 1:39 PM9

10

Introduction

Identification of controls

See the page in for details.

Front panel

Rear panel

When connecting the optical digital cable, remove
the cap and fit the connector into the jack firmly.
When not using the jack, keep the cap inserted
to protect it from dust intrusion.

ON/STANDBY
button

AUDIO (L/R)/VIDEO IN
(LINE IN 2) jacks

22

40

EJECT button

29

Cassette loading slot

29

Disc tray

42

Display window

11

REC button

34

CHANNEL #/$ buttons

34

OPEN/CLOSE button

42

STOP button

PLAY button

FF (Fast Forward)
button

REW (Rewind) button

30

30

30

30

VCR/DVD mode selector button

22

Remote sensor

13

VCR indicator

DVD indicator

42

22

DVD S-VIDEO

OUT jack

19

S-VIDEO/COMPONENT
Video selector switch

19

DVD OPTICAL DIGITAL AUDIO
OUT jack (dust protection cap)

20

DVD AUDIO (L/R)
OUT jacks

19

DVD COAXIAL DIGITAL
AUDIO OUT jack

20

DVD COMPONENT
OUT jacks

19

RF OUT jack

14

RF IN jack

14

AUDIO (L/R)/VIDEO
IN (LINE IN1) jacks

40

DVD/VCR common AUDIO
(L/R)/VIDEO OUT jacks

18

5

AC power cord

J2E50601A (E)p02-13.p65 8/30/04, 5:48 PM10

11

Introduction

VCR operation status

CH 125

8 : 47

AM

MON

00 : 00 : 00 SP

STEREO SAP

While watching TV

DAY OF THE WEEK

CHANNEL

TAPE SPEED

REAL TIME COUNTER

CLOCK

STEREO AND

SECOND

AUDIO

PROGRAM

(SAP)

8 : 30AM MON

00 : 15 : 12 SP

HI-FI

STEREO

While operating a tape

OPERATING
MODE

TAPE IN

AUTO REPEAT

HI-FI STEREO

DVD/CD/VCD operation status

Press CALL to display information on screen.
To cancel the display, press CALL again.

Recording :

Rec/Pause

:

Play :

Stop :

Eject :

VCR Icons

34:56 71:33

Track 11/99

00:34:56 01:12:33

Each press of DISPLAY, the status display of the disc will appear on the screen and change as follows.

DVD

00:34:56 01:12:33

1/9

Title 1/99

1/8

1/32

Chapter 1/999
Eng DolbyDigital
Eng

CD/VCD

DISC

OPERATION

TRACK NO.

ELAPSED TIME

CHAPTER NO.

ANGLE NO.

A KIND OF AUDIO

DISC OPERATION

TITLE NO.

ELAPSED

TIME

TOTAL
TIME

TOTAL
TIME

OUTPUT SELECTION

Timer Recording indicator (VCR)

Multifunctional indicator

Recording

indicator (VCR)

Track indicator (CD)

Tape loaded indicator (VCR)

Play indicator

VCR indicator (VCR)

Still indicator

Disc inserted indicator (DVD)

Disc inserted
indicator (CD)

AM/PM indicator
(AM is not displayed)

Progressive indicator

AUDIO LANGUAGE

SUBTITLE LANGUAGE

Display window

J2D81701A (E)p02-13.p65 28/5/04, 1:39 PM11

12

Introduction

Remote control

* MENU button

Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in “DVD Menu.”

54

Identification of Controls (continued)

The instructions in this manual describe the functions on the remote control. See the page in for details.

FWDREW

STOP

PAUSE/STILL

VCR
DVD

CALL

DISPLAY

TV/VCR

AUDIO SELECT

AUDIO

ATR

SUBTITLE

A-B RPT

CLOCK/COUNTER

SP/SLP

PLAY MODE

COUNTER RESET

ANGLE

INPUT SELECT

PROGRESSIVE

INDEX

SKIP

INDEX

SKIP

TIMER REC

REC/OTR

OPEN/CLOSE

EJECT

MARKER

SET

+

SET

–

CH

–

CH

+

TOP MENU RETURN

ZERO RETURN

JUMP

MENU

VCR MENU

SETUP

CM SKIP

ZOOM

CANCEL

ENTER

PLAY

8

79

654

321

0

SLOW

+–

OPEN/CLOSE button (DVD)

42

ENTER button

23

RETURN button

58

CANCEL button

37

CLOCK/COUNTER button

33

CM SKIP button
ZOOM button

31

54

50

MARKER button

INPUT SELECT button

40

PROGRESSIVE button

66

PAUSE/STILL button

SLOW button

VCR DVD selector button

22

31

SP/SLP button
PLAY MODE button

34

52

AUDIO SELECT button
AUDIO button

39

51

55

FWD button

30

31

INDEX + button

SKIP button

44

33

A-B RPT button

52

PLAY button

30

Channel +/– buttons

34

24

59

CALL button
DISPLAY button

INDEX – button

SKIP button

44

33

TIMER REC button

SET +/

-

buttons

23

EJECT button (VCR)

29

TOP MENU button

54

VCR MENU button
SETUP button

23

47

56

TV/VCR button

22

ATR button
SUBTITLE button

31

COUNTER RESET button
ANGLE button

54

32

37

REW button

30

ZERO RETURN button
JUMP button

32

50

STOP button

30

REC button
OTR button

34
36

*MENU button

( / / / )

Direction buttons

45

Direct channel
selection buttons

Number buttons

45

28

22

) buttonPower (

J2D81701A (E)p02-13.p65 28/5/04, 1:39 PM12

13

Introduction

Operation

• Aim the remote control at the remote sensor and press control buttons to
operate.

• Operate the remote control within 30° angle on either side of the remote
sensor, up to a distance of Approx. 7 meters.

Replace the compartment
cover.

Install two “R03/AAA” batteries
(supplied),

paying attention to the
polarity diagram in the battery
compartment.

Slide the battery compartment
cover in the direction of the
arrow.

Approx. 7 meters

Battery precautions

The precautions below should be followed when using batteries in this device:

1. Use only the size and type of batteries specified.

2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.

Re-

versed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.

3.

Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.

5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery
manufacturer’s directions.)

• Press POWER (

) to turn the DVD VCR on or off.

• Select your desired operating mode (DVD or VCR) using VCR DVD.

(DVD or VCR indicator on the front panel will show you which mode is selected.)

• Press CH + or CH – to move through the channels one channel at a time.

• The CH +/– (

/ ) and SET +/– ( / ) are also used to navigate on-screen menu system.

• You can directly access specific channels using Number buttons.

• Each press of VCR DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the

DVD screen (DVD mode).

1

23

Remote control basics

Inserting batteries

J2D81701A (E)p02-13.p65 28/5/04, 1:39 PM13

14

Connections

OUT

(TV)

IN

(ANT)

OUT
(TV)

IN

(ANT)

OUT
(TV)

IN

(ANT)

Notes: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to

the DVD/VCR properly.

• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type

antenna is required.

• If you are not sure about the connection, please refer to qualified service personnel.

The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV and
connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna
system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.

If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and
one 75 ohm output.

Note:

Combination VHF/UHF Antenna with 75 ohm Coaxial Cable

Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire

Separate VHF and UHF Antennas

DVD/VCR

VHF

UHF

300 ohm Twin Lead (Flat) Wire

(not supplied)

Matching Transformer 300 ohm Input 75

ohm output (not supplied)

300 ohm Twin Lead (Flat) Wire

(not supplied)

75 ohm Coaxial Cable

75 ohm Coaxial Cable

Combiner 75/300 ohm Inputs 75 ohm output

(not supplied)

DVD/VCR

DVD/VCR

Antenna connections

If you are using an antenna system, follow these instructions. If you are a Cable TV subscriber, skip ahead to page 16 for
the proper connections.

Antenna to DVD/VCR connection

1

2

3

J2D81701A (E)p14-17.p65 28/5/04, 1:39 PM14

15

Connections

UHF

VHF

UHF

VHF

VHF/UHF IN

Note: If a VHF or UHF antenna is used,

set the TV/CABLE menu option to
the “TV” mode.

Note: If a VHF or UHF antenna is used,

set the TV/CABLE menu option
to the “TV” mode.

Note: If a VHF or UHF antenna is used,

set the TV/CABLE menu option to
the “TV” mode.

75 ohm Coaxial Cable (supplied)

Splitter 75 ohm Input
75/300 ohm outputs
(not supplied)

Splitter 75 ohm Input
300 ohm outputs
(not supplied)

TV with single 75 ohm VHF/UHF antenna
input

TV with 300 ohm UHF and 75 ohm VHF
antenna inputs

TV with 300 ohm UHF and 300 ohm VHF
antenna inputs

After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the
connection diagram.

This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna
inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.

TV

TV

TV

75 ohm Coaxial Cable
(supplied)

75 ohm Coaxial Cable
(supplied)

DVD/VCR to TV connection

J2D81701A (E)p14-17.p65 28/5/04, 1:39 PM15

16

Connections

Cable TV connections

VHF/UHF

IN (ANT)

OUT

(TV)

IN

(ANT)

VHF/UHF

IN (ANT)

OUT
(TV)

IN

(ANT)

VHF/UHF

IN (ANT)

OUT

(TV)

IN

(ANT)

Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This
DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company
supplied converter box, except for those premium channels which are intentionally scrambled. If you subscribe to a
premium channel which is scrambled, you must have a descrambler box for proper reception.

Allows:*Recording of nonscrambled channels.

*

Use of the programmable timer.

*

Recording of one channel while watching another.

Allows:*Recording of channels through the converter box

(scrambled and unscrambled).

*

Using the programmable timer to record only the
channel selected at the converter box.

Prevents:*Recording one channel while watching another.

*

Using the DVD/VCR tuner to select channels.

DVD/VCR

Incoming Cable

TV

Converter/
Descrambler

Incoming

Cable

TV

TV

To record from converter/descrambler,
DVD/VCR tuner must be tuned to the con­verter output channel, usually channel 3
or 4.

Note:

DVD/VCR

DVD/VCR

Note: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output of

the Converter/Descrambler box, usually channel 3 or 4.

Incoming Cable

Converter/Descrambler

Allows:*Recording of nonscrambled channels.

*

Use of the programmable timer.

*

Recording an unscrambled channel while watching
any channel selected at the converter box.

Prevents: Recording scrambled channels.

If you are playing a tape or using the tuner
built into the DVD/VCR, the converter must
be set to the video channel output of the
DVD/VCR (either 3 or 4).

Note:

1

2

3

J2D81701A (E)p14-17.p65 28/5/04, 1:39 PM16

17

Connections

VHF/UHF

IN (ANT)

A

B

OUT
(TV)

IN

(ANT)

VHF/UHF

IN (ANT)

A
B

OUT

(TV)

IN

(ANT)

This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scram­bled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Con­sult your local cable company for more information concerning connection to their descrambler equipment. There are
many ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.

IMPORTANT: Make sure the TV/CABLE menu option is set to the “CABLE” mode.

Incoming Cable

Allows:*Recording of one channel while watching another.

*

Using the programmable timer to record only the channel selected at the converter box.

*

Recording of all channels through the converter box.

Prevents:*Watching scrambled channels while recording another channel.

*

Using the DVD/VCR tuner to select channels.

DVD/VCR

Splitter

Converter/Descrambler

TV

DVD/VCR

Converter/Descrambler

A/B Switch

TV

Incoming Cable

Splitter

Allows:*Recording of nonscrambled channels.

*

Recording of one channel while watching another.

*

Watching premium channels through the converter while recording nonscrambled channels.

*

Using the programmable timer.

Prevents: Recording scrambled channels.

DVD/VCR

Splitter

TV

Converter/Descrambler

A/B Switch

VHF/UHF

IN (ANT)

A
B

OUT
(TV)

IN

(ANT)

Allows:*Recording of all channels through the converter box.

*

Recording a scrambled or unscrambled channel while watching another (scrambled or
unscrambled) channel.

*

Using the programmable timer to record only the channel selected at the converter box.

Prevents: Using the DVD/VCR tuner to select channels.

A/B Switch

Incoming Cable

Converter/Descrambler

4

5

6

J2D81701A (E)p14-17.p65 28/5/04, 1:39 PM17

18

Connections

Connecting to a TV

Connect the DVD/VCR to your TV.

To VIDEO

OUT

To ANALOG AUDIO OUT

(red) (white)

(yellow)

Signal flow

To wall outlet

To video input

(yellow)

(red) (white)

Audio/video cable (supplied)

To audio inputs

Notes:

• Refer to the owner’s manual of the connected TV as well.

• When you connect the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet before
making any connections.

• If your television set has one audio input, connect the left and right audio outputs of the DVD/VCR to a Y cable adapter (not
supplied) and then connect to your TV.

• Connect the DVD/VCR directly to your TV. If you connect the DVD/VCR to a VCR, TV/VCR combination or video selector, the
playback picture may be distorted as DVD video discs are copy protected.

TV or monitor with
audio/video inputs

Connecting to a TV

Note: This method transports VHS and DVD-video signals. For enhanced DVD-video performance, we recommend you

also connect the S-video or ColorStream® component video outputs to your TV/monitor. (See page 19.)

J2E50601A (E)p18-25.p65 8/30/04, 5:51 PM18

19

Connections

Notes:

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the

wall outlet before making any connections.

• If you place the DVD/VCR near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD/
VCR away from the tuner and radio.

• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate
listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the
speakers may be damaged.

• When connecting to a TV using the Video or S-video jack, make sure that the Progressive indicator “ ” on the
display window is not lit. If it is lit, the Video and S-video outputs do not feed the correct signals and you cannot see
any picture. To turn off the Progressive indicator, select PROGRESSIVE scan Off (see page 66).

Note: The S-video output and component video output transports the DVD-video signal exclusively and will deliver

enhanced DVD video picture performance.

If you connect the DVD/VCR to your TV
with the DVD OUT jacks, select the
corresponding video input on your
television to watch DVD video discs.

TV or monitor with
ColorStream

®

component video inputs

To

PR/CR

video input

To PR/CR
VIDEO
OUT

Signal flow

To wall outlet

To audio inputs of

the amplifier

(red)

(white)

(red)

(white)

To Y
VIDEO
OUT

To PB/CB
VIDEO
OUT

To Y video input

To

PB/CB

video input

Audio system

To ANALOG
AUDIO OUT

To S­VIDEO
OUT

Component video
cable (not supplied)

To S-video input

S-video cable (not supplied)

When you make this connection, set the S-VIDEO/
COMPONENT Video selector switch to the desired
position.
And also you must select the corresponding video
input on your TV.

Audio cable (not supplied)

S-video output

An S-Video connection is superior to Video (Yellow) output. Use this method for DVD playback when the connected television has S­Video input, and does not have component video inputs.

Component video outputs

PROGRESSIVE outputs

Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video
signal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.

INTERLACED outputs

Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest quality
DVD picture playback.

Notes:

• Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)

• In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a

case, adjust the TV or monitor for optimum performance.

Connecting to an audio system and TV equipped with S-video input/component video inputs

J2E50601A (E)p18-25.p65 8/30/04, 5:51 PM19

20

Connections

Connecting to optional equipment

You can enjoy high quality dynamic sounds of DVD video discs or
audio CDs by connecting the DVD/VCR to optional audio
equipment.

For connection to your TV, see “Connecting to a TV”

18 19

.

: Front speaker
: Rear speaker
: Sub woofer

: Center speaker
: Signal flow

Connecting to an amplifier equipped with a Dolby Digital decoder

Connecting to an amplifier equipped with Dolby Surround Pro Logic

Dolby Surround Pro Logic

You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left
front speakers, a center speaker, and one or two rear speakers).

Connecting to an amplifier equipped with a DTS decoder

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for home use,
on DVD video discs or audio CDs.
If you have a DTS decoder or processor, you can obtain the full
benefit of 5.1 channel DTS encoded sound tracks on DVD
video discs or audio CDs.

Manufactured under license from
Dolby Laboratories. “Dolby” “Pro
Logic” and the double-D symbol are
trademarks of Dolby Laboratories.

• Use DVD video discs
encoded via the Dolby Digital
recording system.

• Use DVD video discs or audio
CDs encoded via the DTS
recording system.

*

Connect one or two rear speakers.
The output sound from the rear
speakers will be monaural even if you
connect two rear speakers.

“DTS” and “DTS Digital Out” are
trademarks of Digital Theater Systems,
Inc.

Connect either.

To OPTICAL type
digital audio input

Amplifier equipped with a

Dolby Digital decoder

Optical digital cable

75 Ω coaxial cable

To COAXIAL

type digital
audio input

*

Amplifier equipped with a

DTS decoder

Connect either.

To OPTICAL type
digital audio input

Optical digital cable

To COAXIAL

type digital

audio input

• This selection uses the following reference mark.

To ANALOG
AUDIO OUT

To audio input

Audio cable

75 Ω coaxial cable

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies,
and is now available to reproduce this realistic effect in the home. You can enjoy motion
picture and live concert DVD video discs with this dynamic realistic sound by connecting the
DVD/VCR to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital
processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of
Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital soundtracks,
as well as from titles with the Dolby Surround mark.

Amplifier equipped with

Dolby Surround Pro Logic

With an amplifier equipped with Dolby Digital
Connect the equipment the same way as described in “Connecting to an amplifier
equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set
the amplifier so you can enjoy Dolby Surround Pro Logic sound.

With an amplifier not equipped with Dolby Digital
Connect the equipment as follows.

• This connection is only suitable for Video CDs and
Audio CDs.

J2E50601A (E)p18-25.p65 8/30/04, 5:51 PM20

21

Connections

75 Ω coaxial cable

Optical digital cable

75 Ω coaxial cable

Warning

When playing DTS-encoded discs (audio CDs), excessive noise may be output from the analog stereo jacks. To avoid
possible damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/R) jacks of the
DVD/VCR are connected to an amplification system. (Do not leave the ANALOG AUDIO OUT (L/R) wires dangling.) To enjoy
DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the
BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR.

Connecting to an amplifier equipped with an MPEG2 audio decoder

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by connecting an amplifier equipped with
an MPEG2 audio decoder or MPEG2 audio processor.

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker
system (right and left front speakers).

Notes:

• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the AC-3 RF input of a Dolby Digital Receiver.
This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM AUDIO
OUT jack of the DVD/VCR.

• Connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the “OPTICAL” or “COAXIAL” input of a Receiver or
Processor.

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the

wall outlet before making any connections.

• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the
speakers may be damaged.

• Use DVD video discs
encoded via the MPEG2
recording system.

Amplifier equipped with an

MPEG2 audio decoder

Connect either.

To OPTICAL type
digital audio input

Optical digital cable

To COAXIAL

type digital

audio input

Amplifier equipped with a

digital audio input

Connect either.

To OPTICAL type
digital audio input

To COAXIAL

type digital

audio input

J2E50601A (E)p18-25.p65 8/30/04, 5:51 PM21

22

Basic setup

Setting the video channel

When a TV is connected with the 75 ohm coaxial cable only.

To view playback of a recorded tape or DVD disc, or to watch a
program selected by the VCR's channel selector, the TV must be set to
channel 3 or 4 (video channel).

Setting the video channel

Press POWER to turn on the DVD/VCR.

Press VCR DVD selector to select the VCR mode.

Turn ON the TV and set to CH 3 or 4 to corre­spond with the channel selected in step 1.

Press TV/VCR to select the VCR position.

Select any channel to receive a TV station in your area.
The channel number will appear on the screen for
about 4 seconds.

1

The VCR indicator on the
front panel will light.

2

3

4

5

6

The VCR indicator will
appear in the display
window.

For a push-button TV tuner

If CH 3 or 4 corresponding to the video channel cannot
be tuned on your TV, proceed as follows: set the VCR
3/4 channel selector and the TV to CH 3 or 4, play
back a prerecorded tape and tune the TV to receive a
sharp color picture from the video cassette recorder.
Refer to your TV owner's manual for details.

Note:
If the unit does not operate properly, or No key operation
(by the unit and/or the remote control): Static electricity, etc.,

may affect the player's operation. Disconnect the AC power cord
once, then connect it again.

POWER

VCR DVD

TV/VCR

Press and hold 3 or 4 on the remote for 3
seconds in standby mode.

The video channel will
start to flash for 3
seconds in the display
window.

3
4

OR

VCR
DVD

TV/VCR

3

4

J2D81701A (E)p18-25.p65 28/5/04, 1:39 PM22