Toshiba SAPPHIRE-67CFSG, SAPPHIRE-67DFSG User Manual

SAPPHIRE-67CFSG

SAPPHIRE-67DFSG

TOSHIBA Bluetooth® IC Evaluation Board User’s Manual

SENSYST

Rev 1.0

Regulatory Compliance Information

This evaluation board contains the device that transmit and receive radio signals for the 2.4-GHz unlicensed frequency range and is gained regulatory approvals to be used in Japan and United States.

FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

FCC RF Radiation Exposure Statement.

(1) This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. (2) This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

FCC RF Exposure requirements.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

FCC Interference Statement for Class B devices.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. •

Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced

radio/TV technician for help.

SAPPHIRE Evaluation Board KIT

<Contents >

Evaluation board …1

Jumper socket …19

Reference manual …1

＜Caution＞
 This evaluation board is intended for use for engineering development, demonstration, or evaluation purpose only. Persons handling this product must have

rich electronics knowledge and rich engineering practice. Sensyst does not consider for this product to be a finished end-product fit for general consumer

use. The products incorporated this board are not appropriate for resales.

USB Type A Male to Mini B Male Cable, The coaxial RF adapters suitable for Hirose MS-156C,

and the debugger with half pitch 10 pin cable aren’t included.

If need for your evaluation, please prepare yourself.

1. Introduction

The SAPPHIRE evaluation board includes Toshiba Bluetooth LE IC complies with Bluetooth v4.2, low energy single-mode radio.

Toshiba Bluetooth LE IC is

・Compliant with Bluetooth v4.2 low energy system
・Operating frequency: 2.4 GHz ISM band at 2400-2483.5 MHz (40 RF channels; f=2402+k*2 MHz, k=0, … ,39)
・Maximum output power level: 0dBm (typ.)

This time, we made following changes.

・Flash memory’s capacity in the IC (BTLE IC) is changed from 256KB to 128KB for cost saving
・ROM in the IC (BTLE IC) is changed from 384KB to 216KB for cost saving
・RAM in the IC (BTLE IC) is changed from 192KB to 128KB for cost saving
・A random number generator for security is newly added in the IC(BTLE IC)
・A 32kHz silicon oscillator in the IC(BTLE IC) is deleted for cost saving
・Some components/parts (IC6, CN12, X3, S2) are newly added for using CMSIS-DAP※1

-About A Randam Number Generator-

A random number generator is used to generate the key of the encrypted protocol.

-About CMSIS-DAP-

CMSIS-DAP is the interface firmware for a Debug Unit that connects the Debug Port to USB. Debuggers, which execute on a host computer, connect via USB

to the Debug Unit and to the Device that runs the application software. The Debug Unit connects via JTAG or SWD signals to the target Device. ARM Cortex

processors provide the CoreSight Debug and Trace Unit. CMSIS-DAP supports target devices that contain one or more Cortex processors.

2. Overview

The differences between each model are shown following table.

ORIGINAL

Model

Board

BTLE

Chipset

BTLE Chipset

FCC ID

Name

CMSIS-

DAP

Package

Internal

Flash

Memory

(KB)

Internal

Mask

ROM(KB)

Internal

Work

RAM(KB)

Internal

Silicon

OSC

Internal

Randam

Number

Generator

Model-1

SAPPHIRE-

678FSG

No

TC35678FSG

QFN

40pin

256

384

192

Yes

No

2AKW4-

678FSG

Model-2

SAPPHIRE-

679FSG

No

TC35679FSG

No

384

192

Yes

No

This model

Model

Board

BTLE

Chipset

BTLE Chipset

FCC ID

Name

CMSIS-

DAP

Package

Internal

Flash

Memory

(KB)

Internal

Mask

ROM(KB)

Internal

Work

RAM(KB)

Internal

Silicon

OSC

Internal

Randam

Number

Generator

Model-1

SAPPHIRE-

67CFSG

Yes

TC3567CFSG

QFN

40pin

128

216

128

No

Yes

2AKW4-

678FSG

Model-2

SAPPHIRE-

67DFSG

Yes

TC3567DFSG

No

216

128

No

Yes