Toshiba QOSMIO G35 User Manual

G35
Series User’s Guide
If you need assistance:
Toshiba’s Support Web site
pcsupport.toshiba.com
Toshiba Global Support Centre
For more information, see “If Something Goes Wrong” on
page 282 in this guide.
PMAD00060010 11/05
2
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Model: Qosmio™ G35 Series
Recordable and/or ReWritable Drive(s) and Associated Software Warranty
The computer system you purchased may include Recordable and/or ReWritable optical media drive(s) and associated software, among the most advanced data storage technologies available. As with any new technology, you must read and follow all set-up and usage instructions in the applicable user guides and/or manuals enclosed or provided electronically. If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF.
Protection of Stored Data
For your important data, please make periodic back-up copies of all the data stored on the hard disk or other storage devices as a precaution against possible failures, alteration, or loss of the data. IF YOUR DATA IS ALTERED OR
LOST DUE TO ANY TROUBLE, FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM. WHEN COPYING OR TRANSFERRING YOUR DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED. TOSHIBA DISCLAIMS ANY LIABILITY FOR THE FAILURE TO COPY OR TRANSFER THE DATA CORRECTLY.
Critical Applications
NOTE
The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.
ACCORDINGLY, TOSHIBA, ITS AFFILIATES AND SUPPLIERS DISCLAIM ANY AND ALL LIABILITY ARISING OUT OF THE USE OF THE COMPUTER PRODUCTS IN ANY CRITICAL APPLICATIONS. IF YOU USE THE COMPUTER PRODUCTS IN A CRITICAL APPLICATION, YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.
FCC Notice “Declaration of Conformity Information”
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3
Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's parallel port, monitor port, USB port, PS/2 port port and microphone jack. Changes or modifications made to this equipment not expressly approved by Toshiba or parties authorized by Toshiba could void the user's authority to operate the equipment.
®
, i.LINK®
4
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference
that may cause undesired operation.
Contact either:
Toshiba’s Support Web site at pcsupport.toshiba.com.
Or call the Toshiba Global Support Centre:
Within the United States at (800) 457-7777
Outside the United States at (949) 859-4273
Industry Canada Requirement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.
FCC requirements
The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems.
This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, the information must be provided to the telephone company.
The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC part 68 rules and requirements adopted by the ACTA. It is designed to be connected to a compatible modular jack that is also compliant.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by the ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
Telephone Company Procedures
The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice, in writing, to allow you to make any changes necessary to maintain uninterrupted service.
If Problems Arise
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advanced notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
If trouble is experienced with this equipment, for repair or limited warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
5
Disconnection
If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.
Fax Branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including Fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number
6
provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)
In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer.
Alarm Equipment
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
Instructions for IC CS-03 Certified Equipment
1 NOTICE: The Industry Canada label identifies certified equipment.
This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
2 The user manual of analog equipment must contain the equipment’s
Ringer Equivalence Number (REN) and an explanation notice similar to the following:
The Ringer Equivalence Number (REN) of this device can be found on the label affixed to your computer.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
3 The standard connecting arrangement (telephone jack type) for this
equipment is jack type(s): USOC RJ11C.
Wireless Interoperability
The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to:
The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as defined
and approved by the Institute of Electrical and Electronics Engineers.
The Wireless Fidelity (Wi-Fi) certification as defined by the Wi-Fi Alliance.
The “Wi-Fi CERTIFIED” logo is a certification mark of the Wi-Fi Alliance.
Bluetooth® and Wireless LAN devices operate within the same radio
frequency range and may interfere with one another. If you use Bluetooth and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection.
If you should experience any such problem, immediately turn off your Bluetooth or Wireless LAN device.
Please contact Toshiba PC product support on Web site http://www.toshiba­europe.com/computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.
7
Radio Frequency Interference Requirements
This device is restricted to indoor use due to its operation in the 5.15 GHz to
5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.
High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.
8
Wireless LAN and Your Health
Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:
Using the Wireless LAN equipment on board airplanes, or
In any other environment where the risk of interference to other devices or
services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the Wireless LAN device prior to turning on the equipment.
Exposure to Radio Frequency Radiation
The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. In normal operating configuration, the LCD in the upright position, the distance between the antenna and the user should not be less than 20 cm. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Antenna(s) used in 5.15 GHz to 5.25 GHz frequency band must be integral antenna which provide no access to the end user.
Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.
Regulatory Information
The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user
documentation that comes with the product. This device complies with the following radio frequency and safety standards.
Canada – Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s Web site www.hc-sc.gc.ca/rpb. The RF device shall not be co-located with any other transmitter that has not been tested with this device.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
Pour empecher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit etre utilize a l'interieur et devrait etre place loin des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel (ou son antenne d'emission) est installe a l'exterieur, il doit faire l'objet d'une licence.
9
This device is restricted to indoor use due to its operation in the 5.15 GHz to
5.25 GHz frequency range. Industry Canada requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.
High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.
10
NOTE
EU Declaration of Conformity
TOSHIBA declares, that the product: PLU10* conforms to the following Standards:
Supplementary Information:
This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
VCCI Class B Information
Modem Warning Notice
*The product complies with the requirements of the Low Voltage Directive 72/23/EEC, the EMC Directive 89/336/ EEC and/or the R&TTE Directive 1999/ 05/EEC.
Conformity Statement
The equipment has been approved to [Commission Decision “CTR-21”] for pan­European single terminal connection to the Public Switched Telephone Network (PSTN).
However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
In the event of problems, you should contact your equipment supplier in the first instance.
The above Caution information applies to products that operate with an
802.11a device.
11
Taiwa n
Article 14 Unless approved, for any model accredited low power radio frequency electric
machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.
Article 17 Any use of low power radio frequency electric machinery shall not affect
aviation safety and interfere with legal communications. In the event interference is caused, the use of such electric machinery shall be immediately discontinued. Operation of such products can be resumed only when they are modified and can no longer cause interference.
The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.
Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.
Using this Equipment in Japan
In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station).
1. Sticker
Please put the following sticker on devices incorporating this product.
The frequency bandwidth of this equipment may operate within the same range as industrial devices, scientific devices, medical devices, microwave ovens, licensed radio stations and non-licensed specified low-power radio stations for mobile object identification systems (RFID) used in factory product lines (Other Radio Stations).
1. Before using this equipment, ensure that it does not interfere with any of the equipment listed above.
2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions.
3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations.
12
2. Indication
The indication shown below appears on this equipment.
(3)
(1) (2)
2.4DSOF4
1 2.4: This equipment uses a frequency of 2.4 GHz.
2 DS: This equipment uses DS-SS modulation.
OF: This equipment uses OFDM modulation.
3 The interference range of this equipment is less than 40m.
4 This equipment uses a frequency bandwidth from
2,400 MHz to 2,483.5 MHz.
It is possible to avoid the band of mobile object identification systems.
3. TOSHIBA Direct PC
Monday – Friday: 10:00 – 17:00
Toll Free Tel: 0120-13-1100
Direct Dial: 03-3457-5916
Fax: 03-5444-9450
(4)
Device Authorization
This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan.
The Name of the radio equipment: refer to the equipment label provided on the computer
JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT
Approval Number: D01-1128JP
TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017
The following restrictions apply:
NOTE
NOTE
Do not disassemble or modify the device.
Do not install the embedded wireless module into other device.
5.17 GHz to 5.23 GHz for indoor use only.
Radio Approvals for Wireless Devices
The following information is dependent on what type of wireless device is in your computer.
Approved Countries/Regions for use for the Atheros AR5BMB-43/44 and AR5BMB5 Mini PCI Wireless Network Adapters
This equipment is approved to the radio standard by the countries/regions in the following table.
Do not use this equipment except in the countries/regions in the following table.
13
This device works on passive scan only.
A peer-to-peer mode is not available in 802.11a and Turbo Mode.
802.11b (2.4 GHz)
Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA
14
Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries
België/ Belgique:
Deutschland: License required for outdoor installations. Check with reseller for
France: Restricted frequency band: only channels 1 to 7 (2400 MHz and 2454
Italia: License required for indoor use. Use with outdoor installations not
Nederland: License required for outdoor installations. Check with reseller for
For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m. For registration and license please contact IBPT/BIPT.
Voor privé-gebruik buiten gebouw over publieke groud over afstand kleiner dan 300m geen registratie bij BIPT/IBPT nodig; voor gebruik over afstand groter dan 300m is wel registratie bij BIPT/IBPT nodig. Voor registratie of licentie kunt u contact opnemen met BIPT.
Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment, au­dessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprès de I’IBPT est requise. Pour les enregistrements et licences, veuillez contacter I’IBPT.
procedure to follow. Anmeldung im Outdoor-Bereich notwendig, aber nicht
genehmigungspflichtig.Bitte mit Händler die Vorgehensweise abstimmen.
MHz respectively) may be used outdoors in France. Please contact A.R.T. (http://www.art-telecom.fr) for applicable procedures to follow.
Bande de fréquence restreinte: seuls les canaux 1- 7 (2400 et 2454 MHz respectivement) doivent être utilisés endroits extérieur en France. Vous pouvez contacter I’Autorité de Régulation des Télécommuniations (http://www.art-telecom.fr) pour la procédure à suivre.
allowed. E’necessaria la concessione ministeriale anche per l’uso interno.
Verificare con i rivenditori la procedura da seguire.
procedure to follow. Licentie verplicht voor gebruik met buitenantennes. Neem contact op
met verkoper voor juiste procedure.
15
802.11a (5 GHz)
Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA
Turbo Mode (5 GHz)
Canada USA
Europe - Restrictions for use of 5 GHz Frequencies in European Community Countries
European Community Countries
Austria O x x Belgium, France,
Switzerland/Lichtenstein Denmark, Finland,
Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK
Iceland, Spain O O O
O: allowed ×: forbidden
5150-5250 MHz
Channels: 36, 40, 44,
48
Indoor Only
OO x
OO O
5250-5350 MHz
Channels: 52, 56, 60,
64
Indoor Only
5470-5725 MHz
Channels: 100, 104, 108, 112,
116, 120, 124, 128, 132, 136, 140
Indoor/Outdoor
To remain in conformance with European spectrum usage laws for Wireless
LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply. The user should use the wireless LAN utility to check the current channel of operation. If operation is occurring outside of the allowable frequencies as listed above, the user must cease operating the Wireless LAN at that location and consult the local technical support staff responsible for the wireless network.
The 5 GHz Turbo mode feature is not allowed for operation in any
European Community country.
16
NOTE
This device must not be operated in ad-hoc mode using channels in the
5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point.
This device must be used with Access Points that have employed and
activated a radar detection feature required for European Community operation in the 5 GHz bands. This device will operate under the control of the Access Point in order to avoid operating on a channel occupied by any radar system in the area. The presence of nearby radar operation may result in temporary interruption of operation of this device. The Access Point’s radar detection feature will automatically restart operation on a channel free of radar. You may consult with the local technical support staff responsible for the wireless network to ensure the Access Point device(s) are properly configured for European Community operation.
Approved Countries/Regions for use for the Atheros AR5001X Mini PCI Wireless Network Adapter
This equipment is approved to the radio standard by the countries/regions in the following table.
Do not use this equipment except in the countries/regions in the following table.
This device works on passive scan only.
A peer-to-peer mode is not available in 802.11a and Turbo Mode.
802.11b (2.4 GHz)
Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA
802.11a (5 GHz)
Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA
Turbo Mode (5 GHz)
Canada USA
Approved Countries/Regions for use for the Intel® PRO/ Wireless LAN 2100 3B Mini PCI Adapter
This equipment is approved to the radio standard by the countries/regions in the following table.
Do not use this equipment except in the countries/regions in the following table.
17
Argentina Australia Austria Belgium Brazil Canada Chile Denmark Finland France Germany Greece Iceland Ireland Italy Japan Liechtenstein Luxembourg Mexico Netherlands New Zealand Norway Peru Portugal Singapore Spain Sweden Switzerland UK Uruguay USA Venezuela
18
Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card
This equipment is approved to the radio standard by the countries/regions in the following table.
Do not use this equipment except in the countries/regions in the following table.
Australia Austria Belgium Canada Denmark Finland France Germany Greece Hong Kong Iceland Ireland Italy Japan Liechtenstein Luxembourg Malaysia Netherlands New Zealand Norway Philippines Portugal Singapore Spain Sweden Switzerland Thailand UK USA
Approved Countries/Regions for use for the INPROCOMM IPN2220 Wireless Network Adapter
This equipment is approved to the radio standard by the countries/regions in the following table.
Do not use this equipment except in the countries/regions in the following table.
EU Canada Japan USA Australia New Zealand
Bluetooth® Wireless Technology Interoperability
Bluetooth® Cards from TOSHIBA are designed to be interoperable with any
product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to:
Bluetooth Specification as defined and approved by The Bluetooth Special
Interest Group.
19
Logo certification with Bluetooth wireless technology as defined by The
Bluetooth Special Interest Group.
Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth products with all PCs and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers.
Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.
When you use Bluetooth cards from TOSHIBA close to 2.4 GHz Wireless LAN devices, Bluetooth transmissions might slow down or cause errors. If you detect certain interference while you use Bluetooth cards from TOSHIBA, always change the frequency, move your PC to the area outside of the interference range of 2.4 GHz Wireless LAN devices (40 meters/43.74 yards or more) or stop transmitting from your PC. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/ bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.
Bluetooth and Wireless LAN devices operate within the same radio frequency range and may interfere with one another. If you use Bluetooth and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection. If you should experience any such problem, immediately turn off either one of your Bluetooth or Wireless LAN. Please contact Toshiba PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.
Bluetooth® Wireless Technology and Your Health
The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific
20
community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:
Using the equipment with Bluetooth wireless technology on board
airplanes, or
In any other environment where the risk of interference to other devices or
services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the device with Bluetooth wireless technology prior to turning on the equipment.
Exposure to Radio Frequency Radiation
The radiated output power of the Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled environment, the Bluetooth Card from TOSHIBA has to be operated while maintaining a minimum body to antenna distance of 20 cm.
Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.
The Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits.
Nevertheless, it is advised to use the Bluetooth Card from TOSHIBA in such a manner that human contact during normal operation is minimized.
Regulatory statements
This product complies with any mandatory product specification in any country/ region where the product is sold. In addition, the product complies with the following:
European Union (EU) and EFTA
This equipment complies with the R&TTE directive 1999/5/EC and has been provided with the CE mark accordingly.
21
Canada — Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Taiwa n
Article 14 Unless approved, for any model accredited low power radio frequency
electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.
Article 17 Any use of low power radio frequency electric machinery shall not affect
aviation safety and interfere with legal communications. In the event interference is caused, the use of such electric machinery shall be immediately discontinued. Operation of such products can be resumed only when they are modified and can no longer cause interference.
The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.
Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.
Using this Equipment in Japan
In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station).
1. Sticker
Please put the following sticker on devices incorporating this product.
The frequency bandwidth of this equipment may operate within the same range as industrial devices, scientific devices, medical devices, microwave ovens, licensed radio stations and non-licensed specified low-power radio stations for mobile object identification systems (RFID) used in factory product lines (Other Radio Stations).
1. Before using this equipment, ensure that it does not interfere with any of the equipment listed above.
2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions.
3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations.
22
2. Indication
The indication shown below appears on this equipment.
(1) (2)
(3)
2.4FH1
(4)
1 2.4: This equipment uses a frequency of 2.4 GHz.
2 FH: This equipment uses FH-SS modulation.
3 The interference range of this equipment is less than 10m.
4 This equipment uses a frequency bandwidth from 2,400 MHz to
2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems.
3. TOSHIBA Direct PC
Monday – Friday: 10:00 – 17:00
Toll Free Tel: 0120-13-1100
Direct Dial: 03-3457-5916
Fax: 03-5444-9450
Device Authorization
This device obtains the Technical Regulation Conformity Certification, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law of Japan.
The Name of the radio equipment: EYXF2CS
TELECOM ENGINEERING CENTER
Approval Number: 01NYDA1305
The following restrictions apply:
Do not disassemble or modify the device.
Do not install the embedded wireless module into other device.
DVD-ROM, Multi-function Drive Safety Instructions
The DVD-ROM and multi-function drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Never attempt to disassemble, adjust or repair a CD/DVD drive, CD-RW drive, Multi-drive or any other optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury. Always contact an authorized Toshiba service provider, if any repair or adjustment is required.
Location of the Required Label
(Sample shown below. Location of the label and manufacturing information may vary.)
23
This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT. To use this model properly, read the user’s guide carefully and keep it for your future reference.
Never attempt to disassemble, adjust or repair a CD/DVD drive, CD-RW drive, Multi-drive or any other optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury. Always contact an authorized Toshiba service provider, if any repair or adjustment is required.
24
Copyright
This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
©2005 by Toshiba America Information Systems, Inc. All rights reserved.
Export Administration Regulation
This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and may be subject to the approval of the U.S. Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the U.S. Export Administration Regulations is prohibited.
Notice
The information contained in this manual, including but not limited to any product specifications, is subject to change without notice.
TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT, CONTRACT OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.
Trademarks
Qosmio is a trademark of Toshiba America Information Systems, Inc. and/or Toshiba Corporation.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.
DirectX, Active Desktop, Windows Media, and DirectShow are registered trademarks of Microsoft Corporation.
ConfigFree is a trademark of Toshiba Corporation.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.
Secure Digital and SD are trademarks of the Secure Digital Association.
xD-Picture Card is a trademark of Fuji Photo Film Co. Ltd.
MultiMediaCard is a trademark of Infineon Technologies AG.
Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.
All other brand and product names are trademarks or registered trademarks of their respective companies.
25
Computer Disposal Information
This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at
www.eiae.org.

Contents

Introduction................................................................................ 36
This guide ...............................................................37
Safety icons ............................................................38
Other icons used...............................................39
Other documentation ..............................................39
Service options .......................................................40
Chapter 1: Getting Started........................................................ 41
Selecting a place to work ........................................41
Creating a computer-friendly environment........41
Keeping yourself comfortable ...........................42
Precautions.......................................................42
Important information on your computer’s
cooling fan ..................................................45
Setting up your computer .......................................45
Setting up your software...................................46
Registering your computer with Toshiba ................47
Adding external devices ....................................47
Connecting to a power source ................................48
Using the main battery............................................51
26
Contents
27
Using the computer for the first time......................52
Opening the display panel.................................52
Your computer’s features and specifications ....53
Turning on the power .......................................54
Adding memory (optional)......................................55
Installing a memory module .............................56
Removing a memory module............................61
Using an external keyboard.....................................63
Using a mouse........................................................63
Connecting a printer ..............................................64
Setting up a printer ...........................................65
Using the optional external USB diskette drive........66
Connecting an optional external diskette drive..66
Connecting external display devices .......................67
Connecting the display device...........................67
Directing the display output when you turn on
the computer ..............................................72
Adjusting the quality of the external display......73
Connecting External AV Input Devices ....................73
Turning off the computer ........................................75
Options for turning off the computer ................75
Using the Turn Off Computer or Shut Down
commands..................................................78
Using and configuring Hibernation mode .........80
Using and configuring Standby mode...............82
Closing the display panel ..................................83
Caring for your computer........................................84
Cleaning the computer......................................84
Moving the computer........................................84
Using a computer lock ......................................84
Chapter 2: Learning the Basics................................................ 86
Computing tips .......................................................86
Using the keyboard .................................................88
28
Contents
Character keys .................................................88
Making your keyboard emulate a full-size
keyboard .....................................................88
Ctrl, Fn, and Alt keys .........................................89
Function keys....................................................89
Windows special keys.......................................90
Overlay keys .....................................................90
Using the overlay to type numeric data.............91
Starting a program..................................................92
Starting a program from the Start menu...........92
Starting a program from Windows Explorer .....93
Starting a program from the Run dialog box ....94
Saving your work....................................................95
Printing your work ..................................................97
Backing up your work .............................................98
Restoring your work .........................................98
Using the DVD-ROM or multi-function drive...........99
Drive components and control buttons...........100
Inserting a disc ..............................................101
Playing an audio CD........................................102
Playing CDs using Auto-Run...........................104
Creating a CD or DVD .....................................104
Removing a disc .............................................105
Caring for CD or DVD Discs ...........................106
Toshiba’s online resources ...................................106
Chapter 3: Mobile Computing................................................ 107
Toshiba’s energy-saver design..............................107
Running the computer on battery power ..............107
Battery Notice .................................................108
Power management ........................................109
Using additional batteries ...............................109
Charging batteries.................................................110
Charging the main battery...............................110
Contents
29
Charging the RTC battery................................111
Monitoring main battery power.............................112
Determining remaining battery power.............114
What to do when the main battery runs low ...114
Setting battery alarms.....................................115
Conserving battery power ..............................116
Power Profiles ................................................116
Using a hot key to set the Power Profile .........118
Changing the main battery ....................................119
Removing the battery from the computer .......119
Inserting a charged battery .............................121
Taking care of your battery ...................................122
Safety precautions ..........................................122
Maximizing battery life....................................123
Disposing of used batteries ..................................124
Traveling tips ........................................................125
Chapter 4: Exploring Your Computer’s Features.................. 126
Exploring the desktop ...........................................126
Finding your way around the desktop .............127
Setting up for communications.............................130
Determining the COM port .............................130
Connecting the modem to a telephone line .....132
Connecting to a network ................................133
An overview of using the Internet .........................136
The Internet ....................................................136
The World Wide Web .....................................136
Internet Service Providers...............................136
Connecting to the Internet .............................137
Surfing the Internet.........................................138
Internet features..............................................138
Uploading to, and downloading files from,
the Internet ..............................................139
Exploring audio features .......................................139
30
Contents
Recording sounds...........................................139
Using external speakers or headphones..........141
Using the i.LINK port ............................................142
Inserting and removing PC Cards .........................143
Inserting a PC Card.........................................143
Removing a PC Card.......................................144
Setting up a PC Card for your computer .........144
Inserting an ExpressCard......................................145
Inserting an ExpressCard................................145
Removing an ExpressCard..............................146
Using the Bridge Media Adapter Slot ....................146
Inserting memory media.................................147
Removing memory media...............................147
Using QosmioPlayer .............................................149
Using the Media Control Buttons ....................150
Playing an audio CD........................................150
Playing a DVD .................................................151
Watching television.........................................153
Toshiba Qosmio Remote Control ....................154
Installing the QosmioPlayer Recovery media........159
Chapter 5: Getting to Know the Windows XP Media
Center Edition 2005........................................... 160
Media Center Setup...............................................161
Connecting to a Television ..............................161
Connecting the TV Signal Source When
You Have an Existing Setup ............................163
Starting the Media Center .....................................165
Using Media Center...............................................172
Using the Toshiba Qosmio Remote Control
with Media Center .....................................174
Watching Television Programs .............................181
Selecting a Program from the TV Guide..........182
Watching a Recorded TV Program..................184
Contents
31
Changing a scheduled recording.....................184
Searching for a TV Program to Watch ............185
Recording TV ........................................................186
Recording TV tips ...........................................188
Recording from the Guide...............................189
Recording from Search...................................189
Recording Manually ........................................190
Changing Your Settings ..................................191
Changing recording priorities .........................192
Watching and Recording Movies ....................192
Listening to Music ................................................193
Creating Your Music Library Using
Windows Media Player .............................193
Adding Music from Your Hard Drive to
Windows Media Player Library .................194
Playing Digital Music Files ..............................196
Finding Music Files in My Music.....................197
Playing a Song................................................198
Setting Up an Automatic Disc Jockey .............199
Finding and Playing an Album.........................199
Creating a Playlist ...........................................200
Displaying Your Pictures.......................................201
Viewing a Slide Show......................................203
Sorting your Pictures......................................203
Watching Your Digital Movies...............................204
Organizing Your Videos ..................................204
Playing Digital Videos .....................................205
Playing a Video in Full Screen Mode ...............206
Sorting Videos ................................................206
Watching a DVD....................................................207
Stopping a DVD Movie....................................208
Playing a DVD movie already in your drive .....208
Changing the Media Center Settings .....................209
More Programs.....................................................218
Contents
32
Online Spotlight ....................................................219
Getting Help for Media Center...............................220
Chapter 6: Toshiba Utilities..................................................... 221
Fn-esse .................................................................222
Starting Fn-esse..............................................222
Using the keyboard or pointing device to
assign keys ...............................................224
Viewing existing key assignments...................225
Changing or removing existing key
assignments ............................................226
Hotkey Utility .......................................................226
TOSHIBA Assist ....................................................227
Connect...........................................................228
Secure.............................................................228
Protect & Fix ...................................................229
Optimize..........................................................229
SD Memory Card Format ......................................230
PC Diagnostic Tool ...............................................231
Power Management ..............................................231
Power Usage Profiles......................................232
Quickly creating a new power mode ...............233
Customizing a power mode ............................233
Mouse Utility ......................................................233
Accessing TOSHIBA HW Setup.............................234
TOSHIBA Zooming Utility......................................235
TOSHIBA Picture Enhancement Utility ..................236
CD/DVD Drive Acoustic Silencer ...........................238
TOSHIBA Accessibility ..........................................239
Setting passwords ................................................240
Using an instant password..............................241
Using a supervisor or user password .............241
Fingerprint Authentication Utility...........................244
Fingerprint Enrollment ....................................244
Contents
33
Fingerprint Logon ...........................................246
Power-on Security ..........................................246
Control Center.................................................248
Fingerprint utility limitations ...........................249
Password Bank ...............................................250
Care and maintenance of your fingerprint
sensor.......................................................253
Fingerprint sensor limitations .........................255
Chapter 7: Using the RAID-0 or RAID-1 Utility .................... 257
Using RAID ...........................................................257
RAID-0............................................................258
RAID-1............................................................259
When you first start your computer ................260
Creating a new RAID-0 array.................................262
TOSHIBA RAID Console Utility..............................264
Defining options for RAID-0 or RAID-1...........267
Viewing the status of an array.........................270
Viewing the status of a hard disk drive ...........272
Performing a media check on a RAID-1
array .........................................................274
Breaking a RAID-0 array (striping)..................275
Breaking a RAID-1 array (mirror)....................277
Rebuilding the data on the secondary disk in a
RAID-1 array...................................................278
Restoring a failed drive in a RAID-1 array.............280
Error message examples.......................................281
Chapter 8: If Something Goes Wrong .................................. 282
Problems that are easy to fix ................................282
Problems when you turn on the computer............284
The Windows operating system is not working ....286
Using Startup options to fix problems ............287
Internet problems ...........................................288
34
Contents
The Windows XP operating system can
help you ....................................................288
Resolving a hardware conflict...............................289
A plan of action...............................................289
Resolving hardware conflicts on your own .....290
Fixing a problem with Device Manager ...........291
Memory problems ..........................................293
Power and the batteries ..................................294
Keyboard problems.........................................296
Display problems ............................................297
Disk drive problems........................................299
DVD-ROM or multi-function drive problems...302
Sound system problems .................................303
PC Card problems...........................................303
Printer problems.............................................307
Modem problems............................................308
Wireless networking problems........................309
DVD operating problems.......................................312
Develop good computing habits ...........................315
Data and system configuration backup in
Windows XP .............................................316
If you need further assistance...............................322
Before you contact Toshiba ............................322
Contacting Toshiba .........................................323
Other Toshiba Internet Web sites .........................324
Toshiba’s worldwide offices..................................324
Appendix A: Hot Keys 326
Volume Mute ........................................................326
Password security ................................................327
Without a password........................................327
With a password .............................................327
Maintaining security when the battery is not
fully charged .............................................328
Contents
35
Power usage mode ..............................................329
Standby mode.......................................................330
Hibernation mode ................................................331
Display modes ......................................................332
Display brightness ................................................332
Enabling a wireless device ...................................333
Zooming applications in/out .................................333
Keyboard hot keys ...............................................334
Appendix B: Power Cord/Cable Connectors......................... 335
Appendix C: Using ConfigFree with your Toshiba
Computer ........................................................ 336
Getting Started......................................................337
Starting ConfigFree .........................................337
ConfigFree Utilities................................................339
Connectivity Doctor ........................................339
Search for Wireless Devices ...........................342
Profile Settings ...............................................347
ConfigFree SUMMIT........................................351
Quick Connect.................................................355
Using the Automatic Switch..................................358
Semi-Automatic Switch Feature............................358
Glossary.................................................................................... 360
Index..........................................................................................375

Introduction

NOTE
Welcome to the world of powerful, portable, multimedia computing. With your Toshiba notebook computer, your work and entertainment can accompany you wherever you go.
Certain Microsoft® software product(s) included with this computer may use technological measures for copy protection. IN SUCH EVENT, YOU WILL NOT BE ABLE TO USE THE PRODUCT IF YOU DO NOT FULLY COMPLY WITH THE PRODUCT ACTIVATION PROCEDURES. Product activation procedures and Microsoft's privacy policy will be detailed during initial launch of the product, or upon certain reinstallations of the software product(s) or reconfigurations of the computer, and may be completed by Internet or telephone (toll charges may apply).
Some software may differ from its retail version (if available), and may not include user manuals or all program functionality.
36

This guide

NOTE
Introduction
This guide
The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba's Web site at
While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/ component/options availability are all subject to change without notice. For the most up-to-date product information about your computer, or to stay current with the various computer software or hardware options, visit Toshiba’s Web site at pcsupport.toshiba.com.
pcsupport.toshiba.com.
37
This guide introduces the computer’s features. You can:
Read the entire guide from beginning to end.
Skim through and stop when a topic interests you.
Use the table of contents and the index to find specific
information.
Introduction
NOTE
38

Safety icons

Safety icons
This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows:
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, may result in property damage.
Provides important information.

Other icons used

Additional icons highlight other helpful or educational information:
TECHNICAL NOTE: This icon indicates technical information about the computer.
HINT: This icon indicates helpful hints and tips.
DEFINITION: This icon indicates the definition of a term used in the text.
Introduction

Other documentation

39
Other documentation
Your computer comes with the following documentation:
An electronic version of the user’s guide
It may also contain guides for other programs that may
come with your system.
For accessory information, visit Toshiba's Web site at
accessories.toshiba.com.
Introduction
40

Service options

Service options
Toshiba offers a full line of optional service programs to complement its limited warranty. Toshiba's standard limited warranty, extended warranty, and service upgrade terms and conditions are available at www.warranty.toshiba.com.
To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at
pcsupport.toshiba.com.
If you have a problem or need to contact Toshiba, see “If
Something Goes Wrong” on page 282.
Chapter 1
Getting Started
This chapter provides tips for working comfortably, summarizes how to connect components, and explains what to do the first time you use your notebook computer.

Selecting a place to work

Your computer is portable and designed to be used in a variety of circumstances and locations.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer. Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat.
41
Getting Started
42
Selecting a place to work
To keep your computer in prime operating condition, protect your work area from:
Dust, moisture, and direct sunlight
Equipment that generates a strong electromagnetic field,
such as stereo speakers (other than speakers that are connected to the computer) or speakerphones
Rapid changes in temperature or humidity and sources of
temperature change such as air conditioner vents or heaters
Extreme heat, cold, or humidity
Liquids and corrosive chemicals

Keeping yourself comfortable

The Toshiba Instruction Manual for Safety and Comfort, that shipped with your computer, contains helpful information for setting up your work environment and tips for working comfortably throughout the day.

Precautions

Your computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to the computer.
Avoid prolonged physical contact with the underside or
surface of the computer.
Getting Started
Selecting a place to work
Never allow any liquids to spill into any part of your computer, and never expose the computer to rain, water, seawater or moisture. Exposure to liquid or moisture can cause electric shock or fire, resulting in damage or serious injury. If any of these eventualities should accidentally occur, immediately:
1. Turn off the computer.
2. Disconnect the AC adapter from the power plug socket and computer.
3. Remove the battery pack.
Failure to follow these instructions could result in serious injury or permanent damage to the computer.
Do not turn on the power again, until you have taken the computer to an authorized service center.
If you experience discomfort while operating the computer, stop immediately and rest. Continuous operation for long periods without adequate rest may cause pain in the arms, wrists, hands, neck or other part of the body. If pain persists despite rest, consult your doctor.
43
PC base and palm rest can become hot! Avoid prolonged contact to prevent heat injury to skin.
Read the enclosed Instruction Manual for Safety and Comfort.
Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes.
44
Getting Started
Selecting a place to work
Some PC Cards can become hot with prolonged use. Overheating of a PC Card can result in errors or instability in its operation.
Before you remove a PC Card, always wait for it to cool. You could get burned removing a hot PC Card.
Never place a heavy object on the computer and be careful not to drop a heavy object onto the computer. It could damage the computer or cause system failure.
Never turn off the computer if a drive light indicates a
drive is active.
Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both.
Keep the computer and disks away from objects that
generate strong magnetic fields, such as large stereo speakers.
Information on disks is stored magnetically. Placing a magnet too close to a disk can erase important files.
Handle discs carefully. Avoid touching the surface of the disc. Grasp it by its center hole and edge. If you handle the disc incorrectly, you could damage the disc and possibly lose data.
Scan all new files for viruses.
This precaution is especially important for files you receive via email or download from the Internet. Occasionally, even new programs you buy from a supplier may contain a computer virus. You need a special program to check for viruses. Ask your dealer to help you.
Getting Started
NOTE

Setting up your computer

Important information on your computer’s cooling fan

Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. The cooling fan may be located on the bottom of the computer.
To prevent possible overheating of the CPU, make sure the air intake on the cooling fan is not blocked. The fan draws in air by creating a vacuum. If the fan is blocked, it could cause the CPU to run at a lower performance level or cause the computer to shut down. Loose items such as notebook and tissue paper, plastic wrappers, or other similar materials can block the air intake, preventing air from reaching the CPU. Do not use the computer on surfaces with objects that can be drawn in by the cooling fan.
The cooling fan location will vary depending on the computer.
45
Setting up your computer
TECHNICAL NOTE: You must complete all setup steps up to and including “Setting up your software” on page 46 before adding external or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC Cards.
Your computer contains a rechargeable main battery that needs to be charged before you can use it.
To use external power or to charge the battery you must attach the AC adapter. See “Connecting to a power source”
on page 48.
To register your computer online or to sign up for an Internet account, you must either connect the built-in modem to a
Getting Started
NOTE
NOTE
46
Setting up your computer
telephone line or establish a Local Area Network (LAN) connection. See “Connecting the modem to a telephone line”
on page 132 and “Connecting to a network” on page 133.

Setting up your software

The names of windows displayed, and the order in which windows appear, may vary according to your software setup choices.
The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software.
1 From the welcome screen click Next to enter the Setup
Wizard.
2 Confirm acceptance of Microsoft’s End User License
Agreement and click Next.
3 Select the appropriate option from the Help protect your
computer screen and click Next.
4 Enter the computer name and description and click Next
or Skip.
5 Select how your computer will connect to the Internet
and click Next.
The computer will pause for a moment while checking for an internet connection.
If an Internet connection could not be found, a window will display the message: “An Internet connection could not be chosen.” Click Next to continue.
If you are connecting your computer to a network, consult your system administrator before you choose your computer name and network settings.
Getting Started
NOTE
NOTE

Registering your computer with Toshiba

6 Follow the remaining screen prompts to complete the
setup process.
Once you click the final screen, your computer restarts automatically.
Registering your computer with Toshiba
Product registration is strongly recommended, and allows Toshiba to send the Customer periodic updates, announcements, and special offers applicable to the product. Product registration can be completed during the initial start up process of your computer. If you opt not to register at that time, you can either double-click the icon on your desktop or go to the Toshiba Web site at www.register.toshiba.com. Customer failure to complete Product Registration will not diminish Customer rights under this limited Warranty.
To register online, you must be connected to the Internet via your computer’s modem and a voice-grade telephone line, or by a Local Area Network.
47

Adding external devices

Before adding external devices, Toshiba recommends setting up your software. See “Setting up your software” on page 46.
Before starting to use your computer, you may also want to:
Add more memory (see “Adding memory (optional)” on
page 55)
Connect a mouse (see “Using a mouse” on page 63)
Connect a local printer (see “Connecting a printer” on
page 64)
Getting Started
48

Connecting to a power source

Connect an external diskette drive (see “Using the
optional external USB diskette drive” on page 66)
Connect external speakers or headphones (see “Using
external speakers or headphones” on page 141)
Connect a microphone (there is also an internal
microphone) (see “Using a microphone” on page 140)
Connect a digital or plasma TV (see “Connecting a
digital or plasma television or VCR/DVD player” on page 68)
Connect a standard TV antenna (see “Connecting a
standard television, projector, or VCR/DVD player” on page 70)
Install PC Cards (see “Inserting and removing PC Cards”
on page 143)
Connecting to a power source
Your computer requires power to operate. Use the power cord/cable and AC adapter to connect the computer to a live electrical outlet, or to charge the computer’s battery.
Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug directly. Failure to follow this instruction may damage the cord/cable, and/or result in a fire or electric shock, possibly resulting in serious injury.
When you connect the AC adapter to the computer, always follow the steps in the exact order as described in the User’s Guide. Connecting the power cord/cable to a live electrical outlet should be the last step; otherwise, the adapter DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.
Connecting to a power source
Always use the Toshiba AC adapter that was provided with your computer, or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adapter could cause fire or damage to the computer, possibly resulting in serious injury.
AC adapter
Power cord/cable
Sample power cord/cable and AC adapter
To connect AC power to the computer:
Getting Started
49
AC adapter cord
1 Connect the power cord/cable to the AC adapter.
Sample connecting the power cord/cable to the AC adapter
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
50
_
Getting Started
Connecting to a power source
+
2 Plug the AC adapter into the DC-IN on the back of the
computer.
Sample connecting the AC adapter cord to the computer
3 Connect the power cord/cable to a live electrical outlet.
The AC power light on the indicator panel glows blue.
Never tamper with the cord/cable or plug; never splice or alter a cord/cable; never bend or twist a cord/cable; never place heavy objects on a cord/cable; never place a cord/cable near a heat source; never run a cord/cable through a pinch point such as a door or window; never use nails, staples or similar objects to fasten or attach cord in place; never attempt to disassemble or repair an AC adapter or a Battery Charger. Doing any of the above may damage the cables, and/or result in a fire or electric shock, possibly resulting in serious injury.
Never attempt to connect or disconnect a power plug with wet hands. Failure to follow this instruction could result in an electric shock, possibly resulting in serious injury.
The computer’s main battery light gives you an indication of the main battery’s current charge:
Glows amber while the main battery is being charged
(AC adapter connected)
Glows blue when the main battery is fully charged
NOTE
Is unlit when the main battery has discharged, the battery
is not charging, or the AC adapter is not plugged into the computer or AC outlet
Flashes amber when the main battery charge is low and it
is time to recharge the main battery or plug in the AC adapter
If the AC power light flashes amber during charging, either the main battery is malfunctioning, or it is not receiving correct input from the AC power supply.
Disconnect the AC power cord/cable and remove the main battery pack. See “Changing the main battery” on
page 119 for information on replacing the main battery.

Using the main battery

Getting Started
Using the main battery
51
To charge the main battery, plug the computer into a live wall outlet. It takes several hours to charge the battery with the computer off. It takes much longer to charge the battery while the computer is on. For more information on battery use, see
“Running the computer on battery power” on page 107.
Once the battery is charged for the first time, avoid leaving the computer plugged in and turned off for more than a few hours at a time. Continuing to charge a fully charged battery can damage the battery.
52
NOTE
Getting Started

Using the computer for the first time

TECHNICAL NOTE: When your computer is using all of the power provided by the AC Adapter to run applications, features, and devices, the recharging of the battery cannot occur. Your computer's Power Saver utility can be used to select a power level setting that reduces the power required for system operation and allows the battery to recharge.
TECHNICAL NOTE: The RTC battery does not charge while the computer is turned off, even when AC power is attached.
The RTC battery charges when the computer is powered on.
Battery life and charge time may vary depending on the applications, power management settings, and features used.
Using the computer for the first time

Opening the display panel

Press the display latch and lift the display panel.
Sample opening the display panel
Getting Started
Using the computer for the first time
To avoid damaging the display panel, do not force it beyond the point where it moves easily.
Never lift the computer by the display panel.
Small bright dots may appear on your screen display when you turn on your PC. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology. Over a period of time, and depending on the usage of the computer, the brightness of the screen will deteriorate. This is also an intrinsic characteristic of the screen technology. When the computer is operated on battery power, the screen will dim and you may not be able to increase the brightness of the screen while on battery power.

Your computer’s features and specifications

53
Certain notebook chassis are designed to accommodate all possible configurations for an entire product Series. Your select model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
This information applies to all the features and icons described in this guide.
Below are examples of some of the many possible icons used on your computer:
Sample system icons
Getting Started
54
Using the computer for the first time

Turning on the power

1 Make sure any external devices (such as the AC adapter, if
you plan to use AC power rather than battery power) are properly connected and ready.
The first time you turn on the computer you should not have any accessories or third-party devices attached.
2 Check to ensure that all disc drives are empty.
3 Press and hold the power button until the power button
and the on/off light on the system indicator panel glow blue—approximately one second.
An indicator light on the front of your computer lets you know the system indicator status when the display is closed.
Never turn off the computer while any of the drives are in use. Doing so may damage the media in use and result in loss of data.
4 The preinstalled operating system loads automatically.
When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely.

Adding memory (optional)

Sample turning on the power
The preinstalled operating system loads automatically.
Adding memory (optional)
Getting Started
55
HINT: To purchase additional memory modules, see the accessories information packaged with your system or visit
accessories.toshiba.com.
Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Standby or Hibernation mode, data will be lost.
Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data.
Getting Started
NOTE
56
Adding memory (optional)
For more information on memory options, check the accessories information that came with your computer, or visit accessories.toshiba.com.
Before adding external devices or memory, Toshiba recommends setting up your software. See “Setting up your
software” on page 46.

Installing a memory module

Additional memory modules can be installed in the memory module slots on the base of the computer. You will need a standard Phillips No. 1 screwdriver for this procedure.
If you use the computer for a long time, the memory module will become hot. If this happens, let the module cool to room temperature before you replace it.
To avoid damaging the computer’s screws, use a standard Phillips No. 1 screwdriver that is in good condition.
Installing a memory module with the computer’s power on may damage the computer, the module, or both.
Getting Started
Adding memory (optional)
The computer has two memory module slots — Slot A and Slot B. You can install one or two memory modules.
Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Standby or Hibernation mode, data will be lost.
If the computer is on, begin at step 1; otherwise, skip to step 3.
1 If the computer is on, click Start, Turn off computer.
The Turn off computer window appears.
2 Click Turn O ff.
The operating system turns off the computer.
3 Unplug and remove any cables connected to the
computer, including the AC adapter.
57
4 Remove the battery. For information on removing the
battery, see “Changing the main battery” on page 119.
5 Close the display panel and turn the computer upside
down to locate the memory module slot cover.
Memory module slot cover
Front of computer
Sample locating the memory module slot cover
58
Getting Started
Adding memory (optional)
6 Using a standard Phillips No. 1 screwdriver, loosen the
captive screw that secures the memory module slot cover.
7 Remove the memory slot cover.
Front of computer
Sample removing the memory module slot cover
8 Place the memory module slot cover in a safe place so
that you can retrieve it later.
Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up.
To avoid damaging the memory module, be careful not to touch its pin connector on the side you insert into the computer.
9 Remove the new memory module from its antistatic
packaging.
Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems.
Getting Started
Adding memory (optional)
10 Insert the memory module into the socket on the
underside of the computer.
Memory slots
Front of computer
59
Sample inserting the memory module into the slot
11 Hold the memory module by its edges so that the gold
connector bar faces the slot, at a slight angle to the socket.
clip
clip
Sample inserting the memory module into the socket
12 Check that the module is inserted completely into the
socket and lined up squarely with the socket clips.
60
Getting Started
Adding memory (optional)
Sample aligning the module into the socket
13 Gently press down on the memory module connector
until the clips snap into place.
clip
clip
Sample pressing down on the memory module
Do not force the memory module into position. The memory module should be completely inserted into the socket and level when secured in place.
The clips on either side of the memory module snap into place when the memory module is properly inserted.
14 Replace the memory module slot cover and tighten the
screw.
15 Re-insert the battery. For more information on inserting
the battery, see “Changing the main battery” on page 119.
16 Turn the computer right side up.
17 Reconnect the cables.
18 Restart the computer.
TECHNICAL NOTE: You must have at least one memory module installed for the computer to work.
You can now continue setting up the computer. When the operating system has loaded, you can verify that the computer has recognized the additional memory module.
If you are adding an extra memory module after setting up the computer, verify that the computer has recognized it correctly as described in “Checking total memory” on page 62.

Removing a memory module

If you need to remove a memory module:
1 Complete steps 18 in “Installing a memory module” on
page 56 to shut down the computer and open the memory
module slot cover.
Getting Started
Adding memory (optional)
61
Do not try to remove a memory module with the computer turned on. You can damage the computer and the memory module.
Do not remove the memory module while the computer is in Standby or Hibernation mode. The computer could hang up the next time you turn it on and data in memory will be lost. In either of the above cases, the Standby configuration will not be saved.
The following message appears when you turn on the power:
Warning: Resume Failure Press Any Key To Continue
If the computer hangs up when you turn it on, perform the following: Press the power button and hold it down for at least ten seconds, then turn the power on again.
2 Pull the clips away from the memory module.
62
Getting Started
Adding memory (optional)
The memory module pops up slightly.
3 Gently lift the memory module to a 45 degree angle and
slide it out of the slot.
Front of computer
Sample removing the memory module
4 Replace the memory module slot cover and tighten the
screw.
5 Re-insert the battery. For more information on inserting
the battery, see “Inserting a charged battery” on
page 121.
6 Turn the computer right side up.
7 Reconnect the cables.
8 Restart the computer.
You must have at least one memory module installed for the computer to work.
Checking total memory
When you add or remove a memory module, you can check that the computer has recognized the change. To do this:

Using an external keyboard

NOTE
1 Click Start, Control Panel, Performance and
Maintenance, and then System.
2 The General tab view automatically appears and shows
total memory.
If the computer does not recognize the memory configuration, turn off the computer, remove the memory slot cover, and check that the module is inserted completely into the socket and lined up squarely with the socket clips.
Using an external keyboard
If you prefer to use a full-size keyboard, you can attach one to your computer. The computer’s USB ports support any USB­compatible keyboard.

Using a mouse

You may want to use a mouse instead of the computer’s built-in pointing device. You can attach an external mouse to one of the computer’s USB ports, provided the mouse is USB-compatible.
Getting Started
63
After logging on to your system, the mouse cursor may move to the upper-right side of the screen. If this occurs, press the
Esc or Windows key to return it to its original position.
Getting Started
NOTE
64

Connecting a printer

Connecting a printer
Your printer documentation may require you to install the printer software before physically connecting the printer to your computer. If you do not install the software as instructed by the printer manufacturer, the printer may not function correctly.
Read the documentation that came with your printer. Follow the manufacturer’s instructions when connecting a local printer.
You can connect a USB-compatible printer to your computer through the USB ports. To determine if the printer is USB­compatible, check its documentation.
To make the connection, you need a suitable USB cable, which may come with your printer. If a USB cable was not included with your printer, you can purchase one from a computer or electronics store.
If your printer supports Plug and Play, your computer will automatically recognize the printer; the printer is then ready for use. Refer to your printer documentation for further instructions.
TECHNICAL NOTE: To determine if your printer supports Plug and Play, check its documentation.
If your printer does not support Plug and Play, you must set up the printer as described in “Setting up a printer” on
page 65.
To connect a USB printer to your computer:
1 Connect the printer cable to the printer and then connect
the other end to one of the computer’s USB ports.
2 Plug the printer’s power cable into a live electrical outlet.

Setting up a printer

NOTE
Some printers require a specific installation process. Refer to your printer installation guide for instructions before completing the following procedure.
If your printer does not support Plug and Play, follow these steps to set it up for the first time. You only need to set up the printer once.
1 Click Start, Printers and Faxes.
The Printers and Faxes window appears.
2 Click Add a printer.
The Add Printer Wizard appears.
Getting Started
Connecting a printer
65
Sample Add Printer Wizard
3 Follow the on-screen instructions to set up your printer.
Getting Started
66

Using the optional external USB diskette drive

Using the optional external USB diskette drive
The optional external USB diskette drive allows you to use diskettes and is useful for installing software on the hard disk, exchanging information with other systems, and making backup copies of the files stored on your hard disk.

Connecting an optional external diskette drive

Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5­inch diskettes.
Sample optional external USB diskette drive
To connect an optional external USB diskette drive, connect the cable to one of the USB ports on your computer.
Sample connecting an optional external USB diskette drive
Getting Started

Connecting external display devices

Connecting external display devices
Your computer comes with a built-in LCD display, but you can also connect the following types of external display devices to the video ports described below:
A plasma or digital television or VCR/DVD player via
the Component Out port
A standard television, projector, or VCR/DVD player via
the S-video Out port
An external monitor or projector via the RGB (monitor)
Out port
Before connecting a television, video projector, monitor or other external display device, configure your computer for the type of device you are connecting. To do this, refer to the documentation for your operating system and the device.
67
Coaxial Antenna In port
Sample back of system
You cannot connect both the S-video Out port and the Component Out port to the same device at the same time.
The system display default is set at the factory to S-video Out.
RGB (Monitor) Out port

Connecting the display device

If you are connecting a television or other video display device to the computer’s Component Out port, first refer to
“Selecting video cables” on page 68 for guidelines on
choosing a video cable, then refer to “Connecting a standard
television, projector, or VCR/DVD player” on page 70.
Component Out port
S-video Out port
68
NOTE
Getting Started
Connecting external display devices
If you are connecting an SVGA monitor, skip to “Connecting
an external monitor or projector” on page 71.
Selecting video cables
To connect a device to the S-video port, you must purchase an S-video cable. For the best video quality, always use a properly shielded cable.
HINT: Toshiba recommends using a cable no longer than 20 feet (approximately 6 meters).
Using a poor-quality cable may result in a dull or fuzzy picture, poor color, ghosting, video noise, or loss of video.
Connecting a digital or plasma television or VCR/ DVD player
TECHNICAL NOTE: You must have digital TV service to watch digital TV on your computer. See your TV service provider for more information.
You can watch digital television by connecting to the Component Out port on your computer.
You cannot view digital TV on the display device if you are using it as a monitor.
To do this:
1 Connect the digital television video cable to the Component
Out port on the back of your computer.
Getting Started
Connecting external display devices
2 Connect the three RCA jacks on the other end of the
cable to your digital television. Refer to the manual that came with the television for more information.
3 Turn on your computer.
69
4 While holding down
between each press, until you get the desired setting. For more information, see “Directing the display output when
you turn on the computer” on page 72.
Fn, press F5 repeatedly, pausing
Connecting the sound to a TV or stereo system
At times you may prefer to use external audio instead of the computer’s built-in speakers. For example, when you use a TV or other external display device you can use that device’s speakers, or when you use the computer’s built-in display you can connect to external speakers or a stereo sound system for higher quality sound.
You can connect the sound to external audio devices in two ways:
Using the headphone jack on the left side of the
computer. This lets you connect directly to headphones, powered speakers, or a stereo system that supports input from a headphone output. You need a cable (not shipped with your computer) with a 1/8" (3.5mm) stereo plug on one end and a plug compatible with your sound system on the other end (typically an RCA type connector).
Using the S/PDIF jack on the left side of the computer.
This lets you connect to a sound system that can accept the digital optical signal from your computer. You need an S/PDIF cable (not shipped with your computer) with a Toslink 1/8" (3.5mm) mini plug on one end and a plug compatible with your sound system on the other end.
70
NOTE
NOTE
Getting Started
Connecting external display devices
Connecting a standard television, projector, or VCR/ DVD player
S-video cables are not included with your computer. To connect a device to the S-video Out port, you will need to purchase an S-video cable.
To connect a standard television, projector, or VCR/DVD player:
1 Connect one end of the video cable to the external video
device.
Refer to the documentation provided with the device for the location of its Video In port.
2 Connect the other end of the video cable to the S-video
Out port on the back of the computer.
3 Turn on the external video device. Make sure the input to
the device is correctly set for the S-video port. (See the device’s documentation for more information.)
4 On your computer, press the TV Out button, or toggle the
display using the Out button is located above and to the right of the keyboard.)
If you do not see the image transfer from your computer screen to the external video device, modify the Display Properties as described in “Adjusting the Display Properties” on page 70.
Fn+ F5 hot key combination. (The TV
Adjusting the Display Properties
When using the S-video display port, the desktop shown on your TV may be larger than the screen can show. As a result, you may have to adjust the Display Properties to show the entire desktop on the TV without having to pan the display.
Getting Started
Connecting external display devices
To adjust the display properties
1 Right-click on the Windows Desktop and click Properties.
The Display Properties dialog box appears.
2 In the Display Properties dialog box, click the Settings tab.
Sample Settings Tab
71
3 On the Settings tab, click and drag the Screen resolution
slider to the left to select a lower screen resolution.
TECHNICAL NOTE: Most televisions use or support an 800 x 600 standard resolution.
4 Click Apply, then click OK to close the Display Properties
window.
The screen is now displayed correctly on your TV.
For more information, see “Directing the display output when
you turn on the computer” on page 72.
Connecting an external monitor or projector
You can easily attach an external monitor or projector to your computer if you need a larger screen or to display anything on your computer screen. To do this:
72
Getting Started
Connecting external display devices
1 Connect the monitor’s video cable to the RGB (monitor) port
on the back of the computer.
2 Connect the device’s power cable to a live electrical
outlet.
3 Turn on the external device.
4 While holding down
between each press, until you get the desired setting. See the immediately following section on directing the display output for more information.
Fn, press F5 repeatedly, pausing

Directing the display output when you turn on the computer

Once you connect an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. The quickest way to change the display output settings is to use the display hot key (
1 Press
2 While holding down
Fn and F5 simultaneously.
Fn, press F5 repeatedly, pausing
between each press, until the setting you want takes effect.
This hot key cycles through the settings in the following order:
Built-in display only
Built-in display and external monitor simultaneously
External monitor only
Built-in display and TV (or other external video device)
simultaneously
Fn + F5):
TV (or other external video device) only
3 Release the
Fn key.
Getting Started

Connecting External AV Input Devices

TECHNICAL NOTE: You can also change these settings using the Display Properties Box.
Set the option for the video controller by clicking Start, then Control Panel, and Display. Choose the Settings tab, click the Advanced button, select Display Device, select the applicable Monitor type, and click Apply or OK.

Adjusting the quality of the external display

To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps.
TECHNICAL NOTE: To use one of the simultaneous modes, you must set the resolution of the internal display panel to match the resolution of the external display device. The external display device must support a resolution of 800 X 600 or higher.
73
Connecting External AV Input Devices
Your computer provides ports for connecting the following AV input devices:
A Set-top box or standard television antenna via the
coaxial Antenna In port
VCR/DVD player and game console devices via the S-
video In port or the Composite In port
Connecting a Set-top box or standard TV antenna
You can watch standard television by connecting a Set-top box or antenna to the Antenna In port on your computer. To do this:
74
NOTE
Getting Started
Connecting External AV Input Devices
1 Connect the television Set-top box or antenna to the coaxial
adapter cable.
2 Connect the coaxial adapter cable to the coaxial Antenna
In port on the back of your computer.
3 Turn on your computer.
Connecting to the S-video In port
You can connect an external input device such as a VCR/ DVD player or game console to the S-video In port on the right side of your computer.
S-video cables are not included with your computer. To connect a device to the S-video In port, you will need to purchase an S-video cable.
To connect the device:
1 Connect one end of the video cable to the external video
device.
Refer to the documentation provided with the device for the location of its Video Out port.
2 Connect the other end of the video cable to the S-video In
port on the right side of the computer.
3 Turn on the external video device.
Connecting to the Composite In port
The Composite In port provides another way to connect a VCR/DVD player or game console to your computer. To do this:
1 Connect the external device’s video cable to the Composite
In port on the right side of the computer.
2 Connect the device’s power cable to a live electrical
outlet.
3 Turn on your computer.
4 Turn on the external device.

Turning off the computer

Getting Started
Turning off the computer
75
Pressing the power button before shutting down the Windows work. Make sure the system indicator panel’s disk light and the drive-in-use light are off. If you turn off the power while a disk is being accessed, you may lose data or damage the disk and/ or drive.
It is a good idea to turn off your computer when you are not using it for a while.
If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is off) to fully charge the main battery.
®
operating system could cause you to lose your

Options for turning off the computer

Depending on the operating system installed, you have up to four options when you turn off the computer: Turn Off or Shut Down, Hibernate, and Standby. Each option has its advantages.
Turn Off or Shut Down
Factors to consider when choosing either Turn Off or Shut Down:
Use the Turn Off command if you are using Windows
XP Home, or either Windows Windows connected to a domain server.
®
XP Media Center Edition (MCE) and are not
®
XP Professional or
®
76
Getting Started
Turning off the computer
Use the Shut Down command if you are using Windows
XP Professional or Windows (MCE) and are connected to a domain server.
If you have work in progress and are not connected to a
network, use the Windows commands to save your system settings so that, when you turn on the computer again, you will automatically return to where you left off.
TECHNICAL NOTE: Before using any of these options to shut down or turn off your computer, save your files and make sure the disk activity lights are off.
If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again.
®
XP Media Center Edition
®
Standby or Hibernate
Hibernation mode
Hibernation mode shuts the computer down completely, but it first saves the current state of the computer to the hard disk. Since Hibernation mode does not require power to maintain the saved information, system settings are retained indefinitely.
®
Factors to consider when choosing Hibernation:
While in Hibernation mode, the computer uses no main
battery power.
Because the state of the system is stored on the hard disk,
no data is lost if the main battery discharges.
When starting up again, Hibernation takes less time and
consumes less main battery power than does turning off the computer.
Since information is being retrieved from the hard disk
rather than from memory, restarting from Hibernation takes a little more time and consumes more main battery power to start up than when restarting from Standby.
Getting Started
Turning off the computer
When starting up again, the computer returns to the state
in which you left it, including all open programs and files you were using.
For information on placing your computer into, and configuring your computer for Hibernation mode, see “Using
and configuring Hibernation mode” on page 80.
77
Standby mode
The Standby command places the computer into a power­saving mode. Standby holds the current state of the computer in system memory (RAM) so that, when you restart the computer, you can continue working from where you left off.
Factors to consider when choosing Standby:
While in Standby mode, the computer uses some main
battery power.
The Standby command does not store unsaved
information on your hard disk. You should save your work before putting your computer on Standby.
Restarting from Standby takes less time and consumes
less main battery power than restarting from turning off the computer or using Hibernation mode.
When starting up again, the computer returns to the mode
in which you left it, including all open programs and files you were using.
If you power down using the Standby command and the main battery discharges fully, your unsaved information will be lost. Be sure to save your work first.
For information on using Standby, see “Using and
configuring Standby mode” on page 82.
Getting Started
78
Turning off the computer

Using the Turn Off Computer or Shut Down commands

Depending on the operating system installed, use the following steps to turn off your computer.
Turn Off
For Windows Professional or Windows
®
XP Home, or either Windows
®
XP MCE when not connected to a
domain server, follow these steps to turn off the computer:
1 Click Start, select Turn off computer.
The Turn off computer dialog box appears.
®
XP
Sample Turn off computer Windows
®
dialog box
2 Click Turn O ff.
The computer shuts down completely.
Shut Down
For Windows
®
XP Professional or Windows
connected to a domain server, follow these steps to turn off the computer:
1 Click the Start button, then Shut down.
The Shut Down Windows
®
dialog box appears.
2 Select Shut down from the drop-down list.
3 Click OK.
The computer shuts down completely.
®
XP MCE when
Getting Started
Turning off the computer
79
Turning off the computer more quickly
You can also turn off the computer by pressing the power button.
To use this method, you first need to activate it using Toshiba’s Power Saver utility.
1 Click Start, Control Panel, then click Performance and
Maintenance.
2 Click the Tos hib a Po w er Save r icon.
3 Click on the Setup Action tab.
Sample setup action settings screen
4 Select the options you want from the drop-down lists.
When I press the power button
Set this option to Shut down if you want the computer to shut down when you press the power button.
When I close the lid
Set this option to Shut down if you want the computer to shut down when you close the display panel.
Getting Started
NOTE
80
Turning off the computer
5 Click Apply.
6 Click OK.
For more information about the Power Saver utility, see
“Power Management” on page 231.
Once the computer is configured, you can turn it off by either pressing the power button or closing the display panel, depending on the options set.
Restarting your computer
To start the computer up again, press the power button until the power button and the on/off light glow blue.
If you turn off the computer by closing the display panel, you can start it again by opening the display panel.

Using and configuring Hibernation mode

To turn off the computer using the Hibernation command, click Start, Turn off computer, and select Hibernate.
Sample Turn off computer Windows® dialog box
The computer saves the state of all open programs and files, turns off the display, and then turns off.
Getting Started
NOTE
Turning off the computer
81
Configuring Hibernation mode options
You can place the computer into Hibernation mode by either pressing the power button or closing the display panel. You can also specify an amount of time after which the computer automatically goes into Hibernation mode.
To use any of these methods, you first need to enable them in Toshiba’s Power Saver utility.
1 Click Start, Control Panel, then click Performance and
Maintenance.
2 Click the Tos hib a Po w er Save r icon.
3 Click the Setup Action tab.
4 Select Hibernation for the options you want.
When I press the power button
Set this option to Hibernate if you want the computer to go into Hibernation mode when you press the power button.
When I close the lid
Set this option to Hibernate if you want the computer to go into Hibernation mode when you close the display panel.
5 Click Apply.
6 Click OK.
For more information about the Power Saver utility, see
“Power Management” on page 231.
Once the computer is configured, you can place it into Hibernation mode by either pressing the power button or closing the display panel, depending on the Hibernation options set.
Getting Started
82
Turning off the computer
Starting again from Hibernation mode
To start up the computer from Hibernation mode, press the power button until the power button and the on/off light glow blue. The computer returns to the screen(s) you were using.
If you put the computer in Hibernation mode by closing the display panel, you can start it again by opening the display panel.

Using and configuring Standby mode

To turn off the computer using the Standby command, click Start, Turn off computer, and select Stand By.
Sample Turn off computer Windows® dialog box
The computer saves the status of all open programs and files, turns off the display, and enters into a low-power mode. The power button and on/off light blink amber indicating the computer is in Standby mode.
Configuring Standby mode options
You can place the computer into Standby mode by either pressing the power button or closing the display panel. You can also specify an amount of time after which the computer automatically goes into Standby mode.
To use any of these methods, you first need to enable them in Toshiba’s Power Saver utility.
1 Click Start, Control Panel, then click Performance and
Maintenance.
Getting Started
NOTE
Turning off the computer
2 Click the Tos hib a Po w er Save r icon.
3 Click the Setup Action tab.
4 Select Standby for the options you want.
When I press the power button
Set this option to Standby if you want the computer to go into Standby mode when you press the power button.
When I close the lid
Set this option to Standby if you want the computer to go into Standby mode when you close the display panel.
5 Click Apply.
6 Click OK.
For more information about the Power Saver utility, see
“Power Management” on page 231.
83
Once the computer is configured, you can place it into Standby mode by either pressing the power button or closing the display panel, depending on the Standby options set.
Starting again from Standby mode
To start up the computer from Standby mode, press the power button until the power button and the on/off light glow blue. The computer returns to the screen(s) you were using.
If you place the computer in Standby mode by closing the display panel, you can start it again by opening the display panel.

Closing the display panel

After you have turned off the computer, close the display panel to keep dust and dirt out of the computer.
Getting Started
84

Caring for your computer

Caring for your computer
This section gives tips on cleaning and moving your computer. For information about taking care of your computer’s battery, see “Taking care of your battery” on
page 122.

Cleaning the computer

Keep liquids, including cleaning fluid, out of the computer’s keyboard, speaker grille, and other openings. Never spray cleaner directly onto the computer. Never use harsh or caustic chemical products to clean the computer.
To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth.

Moving the computer

Before moving your computer, even across the room, make sure all disk activity has ended (the drive in-use light stops glowing) and all external peripheral cables are disconnected.
Do not pick up the computer by its display panel or by the back (where the ports are located). Doing so could damage the system.

Using a computer lock

You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an
Getting Started
Caring for your computer
optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com.
Sample computer lock cable
To secure the computer:
1 Loop the cable through or around some part of a heavy object.
Make sure there is no way for a potential thief to slip the cable off the object.
2 Pass the locking end through the loop.
3 Insert the cable’s locking end into the security lock slot
on the computer, then engage the locking device.
85
The computer is now securely locked.
Sample locking the computer
Chapter 2
Learning the Basics
This chapter gives some computing tips and provides important information about basic features.

Computing tips

Save your work frequently.
Your work temporarily stays in the computer’s memory until you save it to the hard disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working. Your computer can be configured to warn you when the battery is running low. See “Setting battery alarms” on
page 115.
HINT: Some programs have an automatic save feature that you can activate. This feature saves your file to the hard disk at preset intervals. See your software documentation for details.
86
Learning the Basics
Computing tips
Back up your files to disks (or other removable media) on
a regular basis. Label the backup copies clearly and store them in a safe place.
If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.
Use Error-checking and Disk Defragmenter regularly to
conserve disk space and improve performance.
Scan all new files for viruses.
This precaution is especially important for files you receive via diskette, email, or download from the Internet.
Take frequent breaks to avoid repetitive-motion injuries
and eyestrain.
Do not turn off the computer if a drive indicator light
indicates a drive is active.
Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both.
87
Before turning off the computer, use the Turn off
computer command or Standby command. See “Turning
off the computer” on page 75 to learn more about
Standby.
The operating system records information, such as your desktop setup, during its shut down procedure. If you do not let the operating system shut down normally, details such as new icon positions may be lost.
Learning the Basics
88

Using the keyboard

Using the keyboard
Your computer’s keyboard contains character keys, control keys, function keys, and special Windows the functionality of a full-size keyboard.
Sample keyboard

Character keys

Typing with the character keys is very much like typing on a typewriter, except that:
The space bar creates a space character instead of just
passing over an area of the page.
The lowercase letter l (el) and the number 1 are not
interchangeable.
The uppercase letter O and the number 0 are not
interchangeable.
®
keys, providing all

Making your keyboard emulate a full-size keyboard

Although your computer’s keyboard layout is compatible with a standard full-size keyboard, it has fewer keys.
A standard full-size keyboard has two editing keys; cursor positioning keys; and a numeric keypad. Pressing the
Fn key simultaneously in combination with one
Enter, Ctrl, and Alt keys;
Learning the Basics
NOTE
Using the keyboard
89
of the specially marked keys allows you to emulate a full-size keyboard.
The emulation Fn key and the Wake up on Keyboard while in Standby are only functional when using the internal keyboard; they are not supported when using a USB keyboard.
Your computer’s keyboard has only one Most of the time, this does not matter. However, some programs assign separate functions to the right and left
Alt keys, or to the regular and numeric pad Enter keys on
and the full-sized keyboard. Using the these separate keys, as follows:
Press Fn and Ctrl simultaneously to simulate the Ctrl key on
the right side of the enhanced keyboard.
Press Fn and Enter simultaneously to simulate the Enter key
on the numeric pad of the enhanced keyboard.

Ctrl, Fn, and Alt keys

Fn
Ctrl
Sample Ctrl, Fn, and Alt keys
Ctrl, Fn, and Alt keys do different things depending on the
The program you are using. For more information, see your program documentation.

Function keys

The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard.
Enter and one Ctrl key.
Ctrl
Fn key, you can simulate
Alt
Sample function keys
Learning the Basics
90
Using the keyboard
F1 through F12 are called function keys because they execute
programmed functions when pressed. Used in combination with the specific functions on the computer. For example, off the pointing device. For more information, see “Fn-esse
on page 222 or “Hot Keys” on page 326.
Fn key, function keys marked with icons execute
Windows® special keys
Sample Windows® special keys
Your computer’s keyboard has two keys that have special functions in Windows:
Windows key—Opens the Start menu
Application key—Has the same function as the
secondary mouse button
Windows key
Application key
Fn+F9 turns
®

Overlay keys

Sample numeric and cursor control overlay
Learning the Basics
Using the keyboard
The keys with gray numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the 10-key keypad on a desktop computer’s keyboard.

Using the overlay to type numeric data

To turn the numeric overlay on, press Fn and F11 simultaneously. The numeric mode light on the keyboard indicator panel glows when the numeric overlay is on.
You can still use the overlay keys to type alphabetic characters while the numeric overlay is on. To do so:
For lowercase letters, hold down Fn while you type the
letters
For uppercase letters, hold down both Fn and Shift while
you type the letters
To use the cursor control overlay when the numeric overlay is on, press and hold down keys. To return to the numeric overlay, release
Shift while you use the cursor control
91
Shift.
To turn off the numeric keypad overlay, hold down the and press indicator panel goes out.
F11 again. The numeric mode light on the keyboard
Fn key
Using the overlay for cursor control
To turn the cursor control overlay on, press Fn and F10 simultaneously. The cursor control mode light on the keyboard indicator panel glows when the cursor control overlay is on.
To type alphabetic characters while the overlay is on:
For lowercase letters, hold down Fn while you type the
letters
For uppercase letters, hold down both Fn and Shift while
you type the letters
92
Learning the Basics

Starting a program

To use the numeric keypad overlay when the cursor control overlay is on, hold down overlay keys. To return to the cursor control overlay, release
Shift.
Shift while you use the numeric
To turn off the cursor control overlay, hold down the and press keyboard indicator panel goes out.
F10 again. The cursor control mode light on the
Starting a program
The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows
If you prefer to open the program first, you have four options. You can:
Double-click the icon for the program on your desktop
Use the Start menu
Use Windows Explorer to locate the program file
Use the Run dialog box
The next three sections explain how to start a program from the Start menu, Explorer, and the Run dialog box.

Starting a program from the Start menu

When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that has an icon in the All Programs menu, follow these steps which use the Windows
®
WordPad program as an example:
Fn key
®
Explorer.
1 Click Start, then point to All Programs.
The Windows menu, which lists programs and program groups. If your program is listed, go to step 3, otherwise, continue with step 2.
2 Point to the program group, in this example, Accessories.
The Accessories menu displays.
®
operating system displays the All Programs
Learning the Basics
Starting a program
3 Click the program, in this example, Wor dPad .
WordPad opens.
To close the program, click the Close button in the upper-right corner of the program’s window.
Starting a program from Windows® Explorer
93
If a program is not listed in the All Programs menu, you can start it from Windows you a view of your computer’s contents as a hierarchy or “tree.” You can easily see the content of each drive and folder on your computer. To use this method, you should know the file name and location of the program’s executable file (this file ends with .exe).
This example opens WordPad using Windows Explorer.
1 Click Start, then point to All Programs.
2 Click Accessories.
3 Click Windows Explorer.
4 In the left pane of the window, click My Computer to
expand the window.
5 In the left pane of the window, click Local Disk (C:).
6 In the left pane of the window, click the folder containing
the program, in this case Program Files.
Windows folder on the right side of the window. The left side of the window shows all the folders contained within the Program Files folder.
®
Explorer shows the contents of the Program Files
®
Explorer. Windows® Explorer gives
7 In the left pane of the window, click Windows NT.
8 In the left pane of the window, click Accessories.
Windows folder on the right side of the window.
®
Explorer shows the contents of the Accessories
Learning the Basics
94
Starting a program
9 In the right pane of the window, double-click
WordPad.exe.
WordPad opens.
To close the program, click the Close button in the upper-right corner of the program’s window.

Starting a program from the Run dialog box

This example uses the Run command to start WordPad.exe:
1 Click Start, then click Run.
The Run dialog box appears.
Sample Run dialog box
2 In the Run dialog box:
If the program is in the Windows
program name.
If you know the program’s location, type the full file path.
3 Click OK.
If you do not know the program’s location, you can search for it by returning to the Start menu and clicking Search. Follow the instructions on the Search screen.
HINT: To run the same program again, click the arrow to the right of the text box and select the command line from the drop-down list.
®
NT folder, type just the

Saving your work

Before you turn off the computer, save your work to the hard disk drive.
Always save your data even when you are using the Standby command. If your battery fully discharges, your information will be lost. Your computer can be configured to warn you when the battery is running low, see “Setting battery alarms”
on page 115.
Many programs offer a feature that saves documents at regular intervals, such as every 15 minutes. Check your programs’ documentation to see whether they have an automatic save feature.
To save:
A file you are updating, open the program’s File menu
and click Save
Learning the Basics
Saving your work
95
A new file, choose Save As from the File menu, type a
name for the file, and click OK
HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.
96
Learning the Basics
Saving your work
Sample Save As dialog box
File names
The Windows® operating system supports long file names which can contain up to 255 characters and can include spaces. Some applications do not support long file names and require file names limited to no more than eight characters.
You may use all the letters and numbers on the keyboard plus these characters: _ ^ $ ~ ! # % & { } ( ) @ and ‘. File names are not case-sensitive.
Using a file extension
Most programs assign an extension to the file name that identifies the file as being created in the program with a particular format. For example, Microsoft with a .doc extension. Any file name with an extension of “.doc” is assumed to be a Microsoft own extension is usually unwise, since the program is unlikely to recognize a strange extension and may refuse to handle your file correctly.
TECHNICAL NOTE: By default, the Windows® operating system does not show file extensions. For information on showing or hiding file extensions, see your Windows help.
®
Word saves files
®
Word file. Creating your
®
online

Printing your work

Verify that the Windows® operating system is set up for your printer as described in “Connecting a printer” on page 64.
TECHNICAL NOTE: You only need to set up the printer the first time you connect it. If you use more than one printer or are changing printers, you need to set up the operating system to run with the additional printer(s).
To print a file:
1 If your printer is not on, turn it on now.
2 Open the File menu of your Windows
Print.
The program displays a Print dialog box.
Learning the Basics
Printing your work
®
program and click
97
Sample Print dialog box
3 Specify the print parameters. For example, the range of
pages and number of copies to print.
4 Click Print.
Learning the Basics
98

Backing up your work

Backing up your work
Back up all the files you create in case something happens to your computer. You can back up your files to different types of media such as CDs, DVDs, diskettes, or to a network, if available.
To back up several files at one time, use the Microsoft Windows hard disk. Also see “Backing up your data to CDs with
Windows XP” on page 318.
Small files can be backed up on diskettes if an optional external diskette drive is available.
®
backup program preinstalled on the computer’s
HINT: Backing up all the files on your hard disk may take a considerable amount of time and multiple CDs/DVDs. You may prefer to use a high-capacity backup system, such as an external hard drive.
®

Restoring your work

To restore information from your backup media to your hard disk, use the Restore page in the backup program. Look in the online Help for your operating system documentation for information on restoring files.
TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to overwrite a file that already exists on the hard disk. Make sure the backup version is the one you want before overwriting the existing file.
Learning the Basics
NOTE

Using the DVD-ROM or multi-function drive

Using the DVD-ROM or multi-function drive
Optical storage has become the preferred medium for software, music, and video. Digital versatile discs (DVDs) provide a significant increase in data storage and support features that are not available on any other video platform. These features include wide-screen movies, multiple language tracks, digital surround sound, multiple camera angles, and interactive menus.
For these reasons, your computer may come with a DVD­ROM drive or multi-function drive.
TECHNICAL NOTE: Your DVD-ROM or multi-function drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region. The drive will allow you to change regions four times. On the fourth change, the region will be “locked in.” That is, the drive will only play DVDs from that last region. Note that changing from region 1 to region 2 and back to region 1 is counted as two changes.
99
For optimum DVD performance, it is recommended that you play DVDs while running the computer on AC power.
You use CD-ROMs and DVD-ROMs to load and run software, and to access reference material such as catalogs, as well as listen to music. A special feature allows you to play audio CDs and movie DVDs even when the computer is turned off. For more information, see “Using QosmioPlayer”
on page 149.
Learning the Basics
100
Using the DVD-ROM or multi-function drive

Drive components and control buttons

The DVD-ROM or multi-function drive is located on the front of the computer. The Media control buttons are located above the keyboard and can be accessed when the display panel is open.
Media control buttons
The control buttons above the computer keyboard let you play audio CDs when the computer is on. You can also use them to play CDs and DVDs when the computer is off using the QosmioPlayer application. For more information on playing CDs and DVDs when the computer is powered off, see “Using QosmioPlayer” on page 149.
CD/ DVD
TV
Play/ Pause
Stop/ Eject
Previous
track
Next track
Record
Sample Media control buttons above the computer keyboard
The TV button:
Launches Windows Media Center and activates the TV
interface, when the computer is powered on and Windows is running. For more information, see
“Watching Television Programs” on page 181.
Launches the QosmioPlayer if the computer is not
powered on.
Brightness
Dolby
®
TV Out
Loading...