OWNER’S MANUAL
LCD Monitor
P32LSA
1
Contents
Safety Instructions-------------------------------------------------------- 3
Notes and Cautions for Use-------------------------------------------- 10
On usage------------------------------------------------------------------------- 10
On disposal or handing over to a new owner -------------------------- 10
Exemptions---------------------------------------------------------------------- 10
Features----------------------------------------------------------------------- 11
Names and Functions of Controls <Unit>------------------------- 12
Names and Functions of Controls <Remote control>--------- 14
Battery Installation-------------------------------------------------------- 15
Supplied Accessories---------------------------------------------------- 16
Connection------------------------------------------------------------------- 17
Connecting the Power Cord--------------------------------------------18
Installation------------------------------------------------------------------- 19
Dimension-------------------------------------------------------------------- 24
Power On/Off---------------------------------------------------------------- 26
Main power switch------------------------------------------------------------- 26
POWER button on the Remote control----------------------------------- 26
Menu Function-------------------------------------------------------------- 27
Function of each button------------------------------------------------------- 27
OSD lock/unlock control------------------------------------------------------ 27
Menu display chart------------------------------------------------------------- 28
Factory default setting--------------------------------------------------------- 29
Input Signal ---------------------------------------------------------------- 30
Input signal
A Guide to Simple Problem Solving--------------------------------- 31
For inquiries---------------------------------------------------------------------- 31
------------------------------------------------------------------- 30
2
Safety Instructions
Before using the unit, please read this manual thoroughly to help protect against damage your own and other people’s property
your property from potential damage and ensure your own and other people personal safety.
Be sure to observe the following instructions with understanding meaning of signs and figures below.
Meaning of Signs
Sign Meaning of Sign
Disregard may cause death or serious injury*1.
1: “Serious injury” refers to blindness, burns (by both high and low temperature), electric shock, break in bones poisoning
which cause hangover or require hospitalization or a long term treatment.
2. “Injury” refers to wounds, burns, electric shock which does not require hospitalization nor a long term treatment.
3: “Material damage” refers to damages extended to houses, household effects, livestocks, pets.
Disregard may cause injury*
2
or material damage*3.
Example of figure
Figure Meaning of Figure
“
The contents are written or shown by picture at inside or near the figure.
“
The contents are written or shown by picture at inside or near the figure.
“
The contents are written or shown by picture at inside or near the figure. The figure on the left
shows caution for High-tension current.
“ shows prohibited matter.
“ shows instructed matter.
“ shows caution.
Warning
Malfunction or Trouble
If smoke or peculiar smells comes from the unit,
remove the power plug from the outlet immediately.
If the unit is still used in this condition, it may cause a fire or an
electric shock.
Make sure that the smoke or smell has stopped, then contact your
dealer for inspection.
If when there isn’t picture or sound, remove the
power plug from the outlet immediately.
If the unit is still used in this condition, it may cause a fire or an
electric shock.
Contact your dealer for inspection.
3
If water is spilled or objects are dropped inside the
unit, remove the power plug from the outlet
immediately.
If the unit is still used in this condition, it may cause a fire or an
electric shock.
Contact your dealer for inspection.
If the unit is dropped or the cabinet is damaged,
remove the power plug from the outlet immediately.
If the unit is still used in this condition, it may cause a fire or an
electric shock. Contact your dealer for inspection.
To turn off the power of the unit, press “○” on the
main power switch.
•
The power standby/on indicator goes off and you cannot turn the unit
on/ off by using the POWER button on the remote control. (To turn
on/off the unit by the remote control, press the main power switch again
and light the power standby/on indicator.)
• When you turn off the unit by pressing the POWER button on the
remote control, the main power of the unit is not turned off.
• To disconnect the unit completely from power supply, remove the
power plug from the outlet.
If the power cord or plug is damaged or becomes
hot, turn off the main power switch of the unit, make
sure the power plug has cooled and remove the
power plug from the outlet.
If the unit is still used in this condition, it may cause a fire or an electric
shock. Contact your dealer for replacement.
Installation
When installing the unit, use the specified stand.
If not, the unit may fall down and cause an injury.
Do not place the unit in locations of high humidity,
such as a bathroom or close to a humidifier.
This may cause a fire or an electric shock.
4
Do not place the unit in an unstable location, such as a
shaky table or incline.
The unit may fall down and cause injury or damage.
Install the unit on a horizontal, stable surface.
Do not place the unit in a location subject to vibration.
The unit may fall down because of the vibration and may cause an
injury.
Insert the power plug fully into a 100-240V AC
outlet.
• If you use an outlet other than 100240 V AC, it may cause fire or electric
shock.
• Improper insertion of the plug may cause heat and fire.
• Do not use a damaged power plug or worn outlet .
Do not place objects on the unit.
If metal or liquid (when putting vase, glass or cosmetics) get into the
unit, it may cause fire or electric shock.
If you put heavy objects on the unit, it may fall down and cause injury.
When installing the unit, have your dealer arrange for
professional installations.
If the installation work is not correct, it may cause injury.
Use
Never repair, modify or disassemble the unit by yourself.
It may cause a fire or an electric shock because dangerous voltages exists in
the unit. Consult your dealer for internal inspection and rep airs.
5
Follow these precautions for the power cord and lug.
Do not damage, modify such as by extending, or heat (such as by pressing
near heating equipment).
Do not pull, place heavy objects or pinch.
Do not bend, twist or bunch up.
Fire or electric shock may result.
Do not insert objects inside the unit.
If metallic materials or combustibles such as paper get inside the unit
from ventilation holes and other places, it may cause a fire or an electric
shock.
Be especially careful that children do not insert objects in the unit.
If there is thunder or lightning, do not touch the unit
or the power plug.
You may suffer an electric shock.
Cleaning
If dust has collected on the power plug connectors,
remove the plug from the outlet and clean off the
dust.
This dust may cause a fire due to reduced insulation of the plug.
Caution
Installation
Do not install the unit where humidity is high.
If the unit is installed in direct sunlight, a closed car or near a stove, it may
cause overheating or electric shock. Also the cabinet or other parts may
distort or be damaged, and electric shock may result.
Do not install the unit where it is exposed to humidity,
oil, smoke or excessive dust.
If the unit is installed next to a humidistat, a stove or in a location where
there is a large quantity of dust, it may cause a fire or electric shock.
6
Take measures to prevent the unit from falling down.
If not, the unit may fall down and cause injury.
Do not block the ventilation holes on the unit.
The inside of the unit will overheat if the ventilation holes are sealed, which
may result in a fire.
• When installing the unit near a wall, keep the unit at least 10 cm from the
wall.
• Do not place the unit in a closet or bookshelf where ventilation is poor.
• Do not spread a newspaper, tablecloth or curtain over the unit.
• Do not place the unit on an unstable surface, such as a rug, or a cushion,
etc.
• Do not place the unit so that it is facing up or down, or on its side.
Precautions for moving the unit:
•
When moving the unit, be sure to remove the plug from the wall outlet and
disconnect wiring cables between equipment and detach any securing
anchors. If not, fire or electric shock may result if the power cord is
damaged, injury may occur by the unit falling down.
• When unpacking or carrying the unit, at least two people are needed. Make
sure the units upright,
• Do not carry the unit with the screen facing up or down.
• Handle the unit so as not to jolt the unit.
Do not overload outlets or cables beyond their
capacity.
Do not use extension cords.
Electric shock or fire may result.
Use
Do not pull the power cord when removing the plug from
the wall outlet.
If the power cord is yanked, the co rd may become damaged and fire or electric
shock may occur. Always hold the plug firmly when removing it.
Never insert or remove the power plug with wet hands.
This may cause electric shock.
7
Do not climb or stand on the unit.
It may drop, fall down, break or cause an injury.
If the unit will not be used for a long period of time,
remove the power plug from the wall outlet for safety.
If not, in the case of malfunction, it may cause fire.
recautions for the remote control batteries:
P
Only use the specified battery type.
he + and –. Be sure to insert batteries by matching t
Do not recharge, heat, disassemble, short or throw b
Do not use the batteries beyond their usage period (designated on
batteries), do not leave worn out batteries in the unit.
Do not mix different types of batteries together.
Do not mix a new battery with a used one.
may leadIf these precautions are not observed, it
explosion and cause burn and injury.
If leaked liquid gets into your eyes or gets in touch with your skin, it may
hurt your eyes or your skin. If leaked liquid gets into your eyes or mouth or
comes in contact with your skin, rinse the contacted area with clean water
immediately and consult your doctor. If the leaked liquid comes in contact
with your cloth, rinse the contacted area with clean water immediately. If
the leaked liquid comes in contact with other equipments, clean them
without touching the leaked liquid.
atteries into a fire.
the
to battery leakage or
Do not push or jolt the LCD panel
The glass of the LCD panel may break and cause
If the screen glass breaks, crystalline liquid leakage m
touch crystalline liquid (liquid).
If leaked liquid gets into your eyes or comes in contact with your skin , it
may hurt your eyes or your skin. If leaked liquid gets into your eyes or
mouth or comes in contact with your skin, rinse the contacted area with
clean water immediately and consult your doctor. If the leaked liquid comes
in contact with your cloth, rinse the contacted area with clean water
immediately. Should the leaked liquid comes in contact with other
equipment, clean them without touching the leaked liquid.
injury.
ay occur. Do not
This product contains chemicals, including lead,
known to the State of California to cause birth defects
or other reproductive harm.
Wash hands after handling.
8
Cleaning
Remove the power plug before cleaning.
If not, it may cause electric shock.
onsult your dealer for internal cleaning once a year. C
If you allow dust to accumulate on the unit, it may cause fire or malfunction
when you operate it.
Cleaning is effective especially before the rainy season when humidity is high.
Refer to your dealer about the service charge for internal cleaning.
9
Notes and Cautions for Use
On usage
• Some parts of the body are hot during operation. Please be careful.
• In case of moving long-distance, wrap the unit with blanket to avoid damages. Be careful not to bump the unit.
• Do not spray on the unit volatile liquid like insecticide. Do not ex pose long time to rubber or vinyl. It will damage the
coating.
On disposal or handing over to a new owner
• It is recommended to initialize the unit by resetting “PICTURE” and “SETUP” menu.
• Do not mix with other general waste.
• Do not dispose LCD monitor in waste treated by a waste treatment center.
• This unit has a lamp inside which includes mercury. For disposal, please follow regulation of your district
Exemptions
• Toshiba is not liable for any damage caused by natural disaster (such as earthquake, thunder, etc.), fires, acts by third
parties, accidents, owner’s intentional misuse and fault, or uses in other improper conditions.
• Toshiba is not liable for incidental damages (such as profit loss or interruption in business, modification or erasure of
record data, etc.) caused by use or inability to use of this product.
• Toshiba is not liable for any damage caused by neglect of the instructions described in the owner’s manual.
• Toshiba is not liable for any damage caused by misuse or malfunction through simultaneous use of this product and the
connected equipment or software.
• Toshiba is not liable for any damage caused by neglect of the instructions described about the installation stand in the
owner’s manual.
• Toshiba is not liable for any damage caused by improper installation.
10
Features
High-resolution HD panel
You can enjoy extreme fine pictures with a big flat LCD monitor panel of 3,150,000 pixel.
MVA system less-reflection black TFT LCD panel
MVA system and Black TFT LCD panel offer bright and wide images with clear contrast. Even placed near the window, the unit
shows bright and clear images with little reflection. The viewing angles of the monitor are as wide as 170° both horizo ntally and
vertically,
Varieties of terminals are available
Video system Input: You have 3 choices of terminals for Video system Input.
VIDEO RCA
S-VIDEO Mini D in 4pin
Y-Pb-Pr Mini Din 8pin
RGB: You have 2 choices of terminals for RGB Input.
RGB ANALOG D-Sub 15 pins
RGB DIGITAL DVI-D 24 pins
Dimmer function
With the photo sensor inside, the panel will adjust the brightness according to the surroun ding light intensity.
There are two brightness level pre-setting. Under bright condition, it will adjust to the brigh t mode. Under dim condition, panel will
adjust to dim mode automatically.
enough to enjoy clear images at any view angle.
11
Names and Functions of Controls <Unit>
Front
Side Controls
Power (standby / on)
Enter (activate selection)
Z/＋ (scroll right for Menu items / volume increase)
Y/－ (scroll left for Menu items / volume decrease)
▽ (scroll down for Menu items)
△ (scroll up for Menu items)
Menu/ (OSD control Menu button / Access Main /
Exit Sub-menu / Quick Menu Selection)
• Power standby / on indicator
-Power ON-Stand by Indicator
• Remote sensor
• Light sensor
-Remote Control Receiver
-Light sensor
12
Back
AC power cord inlet
Main power switch
13
A
y
Names and Functions of Controls <Remote control>
(Option)
Power on / Power off
Menu Left
Menu Up
Activate selection
Adjust clock, phase, H
position and V position
utomaticall
Picture in picture
OSD control Menu button /
Access Main / sub-menu / Quick
Menu Selection
Menu Right
Menu Down
One level up
Input source selection
PIP picture switch
14
Battery Installation
(Option)
(1)
(2)
(3)
To replace batteries inside
1) Push down a little as (1) in the picture and pull the back cover
2) Replace with the new batteries as (2), 1 piece Lithium battery (CR2032) make sure the polarity of batteries are
correct.
3) Place back cover and slide it is as (3) in the picture.
4) Used batteries need to follow the city rule to discard.
5) Avoid keeping used, old batteries inside the remote control, causing leakage of internal liquid resulting metal rust
or fatal damage to the remote control hand unit.
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Effective range
• Point the remote control at remote sensor on LCD monitor.
About the remote control
• Do not drop, shake or bump.
• Do not wet, do not place on wet materials.
• Do not dismantle.
• Do not place in locations exposed to high temperature or high humidity levels.
15
Supplied Accessories
Please check all are supplied.
Power Cord x 1 (1.8m) Owner’s Manual x 1
OWNER’S MANUAL
LCD Monitor
P32LSA
M4 Screws x 4 pieces M6 Screws x 4 pieces
16
Connection
VIDEO SYSTEM INPUT
You can select VIDEO input from 3 terminals below;
VIDEO-IN
S-VIDEO
YUV (Y Pb/Cb Pr/Cr)
• Suitable signal is automatically selected.
Terminal Type
S-Video Mini Din 4pin
Component Mini Din 8 pin
RGB INPUT
You can select RGB input from 2 terminals below;
RGB ANALOG
RGB DIGITAL
Terminal Type
D-Sub 15 pin
DVI-D 24 pin
RCA
Suitable signals
NTSC/PAL
NTSC/PAL
NTSC/PAL
Suitable signals
RGB ANALOG
RGB DIGITAL
17
Connecting the Power Cord
t
Caution: Please turn off the main power switch before connecting.
[Back]
To unit inlet
AC100~240V
Power cord (1.8m)
Main power switch
Ground To wall outle
18
Installation
Wall hanging accessory is available when you hang the monitor on the wall.
Please follow the process mentioned on page 20-22.
When you install the monitor on the ceiling or on the floor, please follow the process on page 23.
To a service technician
For safety, make sure the place has enough strength to hold the whole weight of the monitor and the frames (*1). If
necessary, reinforce the place before installation.
At least two people are needed for installation.
Be careful not to lose removed screws or parts.
Before starting installation, discuss well with customers about the position to install, and get their agreement.
Af ter installation, check the installation is correct and safe.
*1: About the material and the structure of the wall, ceiling and floor to install LCD monitor
Where to install the LCD monitor
If the wall is made of thin plywood or plastered board, it cannot hold the weight.
The chart below shows adaptable anchors for each material. Please check well the structure and strength of the place to install,
and choose the best method for safety.
Adaptable anchors / screws for each material
Material Anchor
Plastered board
Plywood board
Concrete Whole anchor or Bolt
Block
ALC
Mortar
Brick
Wooden pillar Coach bolt (diameter: 6mm x length: 60mm)
For assembly, a screwdriver with more than 300mm shaft is needed.
Impossible to install in Plastered board or Plywood board. Install in the tie beam instead of the wall.
Tie lock anchor
19
How to install the monitor on the wall
In case of using option bracket (FPT-WA5)
1. Remove the stand of the LCD monitor
To avoid damage, spread blanket on the table to put the LCD
monitor on.
To remove the stand of the LCD monitor, put the LCD
monitor on the edge of the table, and remove the screws on the
stand.
Describe d below is one example of how to install the un it on
the wall. The wall hanging accessory will need to be
manufactured according to the installation, so consult your
dealer before the installation work.
2. Wall hanging accessory
Wall hanging accessory is available at the shop.
*: In the package, the bracket and the frame of wall hanging
accessory are assembled. Please separate the bracket and the frame
at first. After the bracket is fixed on the wall, fix the frame on the
LCD monitor.
3. Remove the frame from the bracket
Hold the lower part of the frame and raise it up to remove from the
bracket.
4. Fix the bracket on the wall
Fix the bracket on the wall firmly with anchors or screws (not
supplied).
Make sure anchors or screws are stable.
(Choose appropriate anchors or screws depending on the
structure and material of the wall.)
Refer to the chart on page 19 to check the condition of the
wall, and choose the safe and appropriate way for installation.
20
5. Using Supplied screws, fix the frame on the LCD monitor
To avoid damaging, spread blanket on the flat space, and place
the LCD monitor with its panel down.
Refer to the illustration, and mount the frame on the LCD
monitor with four M4 screws.
6. Wire before hanging on the wall
On wiring, refer to page 17 – 18.
Pay attention to the positions of auxiliary equipment or
bracket on the wall, when you decide the route to wire.
21
7. Mount the LCD monitor on the bracket
*: When mounting, at least two people are needed.
Raise the LCD monitor, and insert the projection of the
bracket.
Ho ld the lower part of th e LCD monitor and raise a little, push
into the lower part of the bracket.
Fasten with supplied screws
22
How to install the LCD monitor on the floor
1. Remove the stand of the LCD monitor
To avoid damage, spread blanket on the table to put the LCD
monitor on.
To remove the stand of the LCD monitor, put the LCD monitor
on the edge of the table, and remove the screws on the stand.
2. Floor installation brace for LCD monitor
The floor installation brace will be manufactured according to the
installation.
Before the installation work, please consult your dealer for the
floor installation brace.
3. Fixing the floor installation brace to the floor
Fix the brace to the floor firmly with anchors or screws (not
supplied).
Refer to the chart on page 19 to check the installation
conditions, and choose a safe and appropriate way to install.
4. Wiring and mounting of the LCD monitor
For wiring details, refer to pages 17 – 18.
Raise the LCD monitor and fix it to the floor installation brace
with screws.
At least two people are needed for this work.
How to install the LCD monitor to the ceiling
1. Remove the stand of the LCD monitor
To avoid damage, spread blanket on the table to put the LCD
monitor on.
To remove the stand of the LCD monitor, put the LCD monitor
on the edge of the table, and remove the screws on the stand.
2. Ceiling installing bracket for LCD monitor
The ceiling installing bracket will be manufactured according to
the installation.
Before the installation work, please consult your dealer for the
ceiling installing bracket.
3. Fixing the ceiling installing bracket on the ceiling
Fix th e bracket on the ceiling firmly with anchors or screws
(not supplied).
Refer to the chart on page 19 to check the installation
conditions, and choose a safe and appropriate way to install.
4. Wiring and mounting of the LCD monitor
For wiring details, refer to pages 17 – 18.
Raise the LCD monitor and fix it on the ceiling installing
bracket with screws.
At least two people are needed for this work.
23
Dimension
Front
24
Back
25
A
Power On/Off
Before turn on, wire all the cable connecting to auxiliary equipment, external speakers, power cord , etc.
There are two controls for power, Main power switch and POWER (standby / on) button.
Main power switch
Bottom Front
To unit inlet
Power cord
Main power switch
To wall outlet ground
If Main power switch is not On, you cannot turn on the unit by the POWER (Standby / On) button.
C100~240V
wall socket
POWER button on the remote control (Option)
About the control by the POWER button on the unit side on, refer to page 12.
POWER button on the Remote control.
You can switch Power standby to On by pressing
this button.
Mode Standby Power on
LED indicator Orange Green
26
Menu Function
Display Menu, you can adjust pictures and sound or set various function s with the buttons on the remote control.
The following are summary of Menu Function. For details, please see to refer pages.
Function of each button
Side of the unit Remote control (option)
Side of the unit: Remote control
No.
Key Descriptions
1 Power Power on / Power off
2 Enter Activate selection
Z/＋
3
4
5
6
7
Y/－
Menu /
Menu Right / Volume Incre ase
Menu Left / Volume Decrease
▽
Menu Down
△
Menu Up
OSD control Menu button /
Access Main / Sub-menu / Quick
Exit
Menu Selection
OSD lock/unlock control:
1. Use control push buttons at side:
Lock: Press (Z/+) and (▽) at the same time and OSD will be locked.
Unlock: Press (Z/+) and (▽) at the same time again and OSD will be unlocked.
2. Use remote controller:
Lock: Press Enter, Enter, Exit, Exit, Enter and Exit on the controller by sequence and OSD will be
locked.
Unlock: Press Enter, Enter, Exit, Exit, Enter and Exit on the controller by sequence again and OSD will
be unlocked
No.
Key Descriptions
1 Power Power on / Power off
2Auto
3 Source Input source selection
4 PIP Picture in picture
5 Switch PIP picture switch
6 Enter Activate selection
7 Menu
8 Exit One Level up
9
10
11
12
Adjust clock, phase, H position and V position
Automatically
OSD control menu button / Access Main /
Sub-menu / Quick menu selection
△
Menu Up
▽
Menu Down
Menu Left
Y
Menu Right
Z
27
Menu display chart
MAIN MENU DISPLAY Brightness ．．．．．．．．．．．． （－ , ＋）
Contrast ．．．．．．．．．．．． （－ , ＋）
(Main) Hue ．．．．．．．．．．．． （－ , ＋）
Saturation ．．．．．．．．．．．． （－ , ＋）
Flash-Tone ．．．．．．．． （Off,Weak,Soft,Strong）
Black Level ．．．．．．．．．．．． （－ , ＋）
POSITION Zoom ．．．．．．．．．．．． （In , Out）
Zoom Horizontal Pan ．．．．．．． （Left,Right）
Zoom Vertical Pan ．．．．．．．． （Down,Up）
Vertical ．．．．．．．．．．．． （－ , ＋）
Horizontal ．．．．．．．．．．．． （－ , ＋）
PIP CONTROL PIP Mode ．．．．．．．．．． （Off,Single,PAP）
PIP Size ．．．．．．．．． （Small,Med,Large）
Vertical ．．．．．．．．．．．． （－ , ＋）
Horizontal ．．．．．．．．．．．．
IMAGE Scaling ．．．．．．． （1:1,Fill,Aspect,Panor）
Auto Adjust ．．．．．．．．．．． （Select）
Phase ．．．．．．．．．．．． （－ , ＋）
Clock ．．．．．．．．．．．． （－ , ＋）
COLOR Color Temperature ．．．．．．（User,6500K,9300K）
Red ．．．．．．．．．．．． （－ , ＋）
Green ．．．．．．．．．．．． （－ , ＋）
Blue ．．．．．．．．．．．． （－ , ＋）
Second Input Signal
Vertical ．．．．．．．．．．．．．．．．．．．．．． （－ , ＋）
Horizontal ．．．．．．．．．．．．．．．．．．．．．． （－ , ＋）
Blend ．．．．．．．．．．．．．．．．．．．．．． （－ , ＋）
Time Out ．．．．．．．．．．．．．．．．．．．．．． （－ , ＋）
Osd Zoom ．．．．．．．．．．．．．．．．．．．．．． （On , Off）
English ．．．．．．．．．．．．．．．．．．．．．． （
（－ , ＋）
Select）
By resetting to factory default; all saved setting will be lost
Factory Reset ．．．．．．．．．．．．．．．．．．．．． （Yes , No）
▽ (Input Signal Selection) VGA
DVI
Composite
S-Video
Component
28
Factory default setting
Power switch Off
Brightness 80
Contrast 50
Color temp. User
Red 50
Green 50
Blue 50
Language English
Auto Configuration On
Item Default
29
Input Signal
A
A
Input signal
Format for RGB DVI input signal (Timing)
Video
Sync
< Horizontal >
<Vertical >
B
C
Item Video Mode
1
10
11
2
3
4
5
6
7
VESA
8
9
VGA 640x480
SVGA 800x600
XGA 1024x768
1152x864 67.500 75.000 108.000 P P 1600 128 256 1152 64 900 3 32 864 1 O O
H-parameters
D E
: Total period
B: Sync. width
C: Back porch
D: Active video
R SPQ
O
E: Front porch
fH
(kHz)
31.469 59.940 25.175 N N 800 96 48 640 16 526 2 33 480 11 O O
37.861 72.809 31.500 N N 832 40 128 640 24 520 3 28 480 9 O O
37.500 75.000 31.500 N N 840 64 120 640 16 500 3 16 480 1 O O
35.156 56.250 36.000 P P 1024 72 128 800 24 625 2 22 600 1 O -
37.879 60.317 40.000 P P 1056 128 88 800 40 628 4 23 600 1 O O
48.077 72.188 50.000 P P 1040 120 64 800 56 666 6 23 600 37 O O
46.875 75.000 49.500 P P 1056 80 160 800 16 625 3 21 600 1 O O
48.363 60.004 65.000 N N 1344 136 160 1024 24 806 6 29 768 3 O O
56.476 70.069 75.000 N N 1328 136 144 1024 24 806 6 29 768 3 O O
60.023 75.029 78.750 P P 1312 96 176 1024 16 800 3 28 768 1 O O
fV
(Hz)
Dot
clock
(MHz)
Sync
polarity
H V A B C D E O P Q R S
Horizontal (dot) Vertical (line)
V-parameters
O: Total period
P: Sync. width
Q: Back porch
R: Active video
S: Front porch
Analog
Digital
(Optional)
12
13
14
VGA TEXT 720x400 31.469 70.087 28.322 N P 900 108 45 720 27 449 2 35 400 12 O O
15
16
Macintosh
17
Item Video Mode
18
NTSC NTSC 358-443 15.734 59.94 16.521
19
PAL PAL SECAM 15.625 50.00 16.406
SXGA
1280x1024
640x480 35.000 66.667 30.240 N N 864 64 96 640 64 525 3 39 480 3 O -
832x624 49.725 74.500 57.283 N N 1152 64 224 832 32 667 3 39 624 1 O -
1024x768 60.150 74.720 80.000 N N 1330 96 168 1024 42 805 3 31 768 3 O -
63.981 60.020 108.000 P P 1688 112 248 1280 48 1066 3 38 1024 1 O O
79.976 75.025 135.000 P P 1688 144 248 1280 16 1066 3 38 1024 1 O -
fH
fV
(kHz)
(Hz)
Dot Clock
(MHz)
30
A Guide to Simple Problem Solving
Before calling service personnel, please check the following chart for a possible cause to the trouble you are experiencing.
Symptom Check these things Page
No picture
The remote control does not operate
The picture color is pale, or not clear
For inquiries and repair
．Make sure the power cord is plugged in.
．Maybe the power is Off or Standby.
．Check whether the auxiliary equipment is connected.
．Check the input setting is correct.
．Signal may not be suitable.
．Make sure the batteries are inserted matching the + and – marks of
the battery compartment.
．The batteries may be exhausted.
．Use the remote control aiming at the remote control sensor.
．Check the picture quality adjustment.
．If you are using YUV terminals, make sure cables are correctly
connected.
18
26
17
27,28
28
15
28
17
Please refer to the shop you bought the unit for repair and inquiries.
31
Note
32
USER-INSTALLER CAUTION
YOUR AUTHORITY TO OPERATE THIS FCC CERTIFIED EQUIPMENT COULD BE VOIDED IF
YOU MAKE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THIS PART
RESPONSIBLE FOR COMPLIANCE TO PART 15 OF THE FCC RULES.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interferen ce when the equipment is operated
in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residen tial area
is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
It may be against copyright regulation to broadcast commercial video software or unit programs for commercial purpose using
this product, or to rewrite such software or programs with wipe-mirror function.
Please refer to a entitled party for approval in advance.
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.
Annex
Suggested text for the notice indicating compliance with this Standard:
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe A est conforme a la norme NMB-003 du Canada.
About trademarks
VGA, SVGA, XGA and SXGA are trademarks or registered trademarks of International Business Machine Corporation.
TOSHIBA LIGHTING & TECHNOLOGY CORPORATION
33
Loading...