Toshiba M11 User Manual

Download

User’s Manual

TECRA M11

computers.toshiba-europe.com

Chapter 1 Getting Started

Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

System Recovery Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

System Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Chapter 2 The Grand Tour

Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Left side. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Front with the display open. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15

AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17

TECRA M11

Chapter 3 Hardware, Utilities and Options

Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Utilities and Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Optional devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

Bridge media slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32

Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33

User’s Manual ii

TECRA M11

Chapter 4

Operating Basics

TOSHIBA Dual Pointing Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Using the Fingerprint Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Web Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Using the TOSHIBA Face Recognition . . . . . . . . . . . . . . . . . . . . . . . 4-11

Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

Writing CD/DVDs on DVD Super Multi drives . . . . . . . . . . . . . . . . . 4-18

Sound System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30

LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39

Computer Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41

Using the TOSHIBA USB Sleep and Charge Utility . . . . . . . . . . . . . 4-44

Heat dispersal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-46

Chapter 5 The Keyboard

Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Soft keys: FN key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Hot keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Keypad overlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Generating ASCII characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Chapter 6 Power and Power-Up Modes

Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Monitoring of power condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

Power-up modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

System automatic Sleep/Hibernation . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Chapter 7 HW Setup

Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

HW Setup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Chapter 8 Troubleshooting

Problem solving process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Hardware and system checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

TOSHIBA support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23

User’s Manual iii

TECRA M11

Appendix A

Appendix B Display Controller and Video mode

Appendix C Wireless LAN

Appendix D Bluetooth wireless technology Interoperability

Appendix E AC Power Cord and Connectors

Appendix F TOSHIBA PC Health Monitor

Appendix G Legal Footnotes

Appendix H If your computer is stolen

Specifications

Glossary

Index

User’s Manual iv

Disclaimer

TECRA M11

© 2010 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.

TOSHIBA TECRA M11 User’s Manual First edition April 2010 Copyright authority for music, movies, computer programs, databases and

other intellectual property covered by copyright laws belongs to the author or to the copyright owner. Copyrighted material can be reproduced only for personal use or use within the home. Any other use beyond that stipulated above (including conversion to digital format, alteration, transfer of copied material and distribution on a network) without the permission of the copyright owner is a violation of copyright or author's rights and is subject to civil damages or criminal action. Please comply with copyright laws in making any reproduction from this manual.

This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the TOSHIBA TECRA M11 Portable Personal Computer at the time of this manual’s production. However, succeeding computers and manuals are subject to change without notice. TOSHIBA assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manual.

Trademarks

IBM is a registered trademark and IBM PC is a trademark of International Business Machines Corporation.

Intel, Intel SpeedStep, Intel Core and Centrino are trademarks or registered trademarks of Intel Corporation.

Windows, Microsoft and Windows logo are registered trademarks of Microsoft Corporation.

Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license.

Photo CD is a trademark of Eastman Kodak Company. Memory Stick, Memory Stick Duo, Memory Stick PRO, Memory Stick PRO Duo and Memory Stick Micro are trademarks or registered trademarks of

Sony Corporation. ConfigFree is a trademark of Toshiba Corporation. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Secure Digital and SD are trademarks of SD Card Association. MultiMediaCard and MMC are trademarks of MultiMediaCard Association. ExpressCard is a trademark of PCMCIA. xD-Picture Card is a trademark of FUJIFILM Corporation. Other trademarks and registered trademarks not listed above may be used

in this manual.

User’s Manual v

EU Declaration of Conformity

This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site

http://epps.toshiba-teg.com on the Internet.

CE compliance

This product is labelled with the CE Mark in accordance with the related European Directives, notably Electromagnetic Compatibility Directive 2004/ 108/EC for the notebook and the electronic accessories including the supplied power adapter, the Radio Equipment and Telecommunications Terminal Equipment Directive 1999/5/EC in case of implemented telecommunication accessories and the Low Voltage Directive 2006/95/EC for the supplied power adapter. Furthermore the product complies with the Ecodesign Directive 2009/125/EC (ErP) and its related implementing measures.

This product and the original options are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented. In this case the persons who have connected/implemented those options/cables have to provide assurance that the system (PC plus options/cables) still fulfils the required standards. To avoid general EMC problems, the following guidance should be noted:

■ Only CE marked options should be connected/implemented

■ Only best shielded cables should be connected

TECRA M11

Working environment

This product was designed to fulfil the EMC (Electromagnetic Compatibility) requirements to be observed for so-called "Residential, commercial and light industry environments". TOSHIBA do not approve the use of this product in working environments other than the above mentioned "Residential, commercial and light industry environments".

For example, the following environments are not approved:

■ Industrial Environments (e.g. environments where a mains voltage

of 380 V three-phase is used)

■ Medical Environments

■ Automotive Environments

■ Aircraft Environments

Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA.

The consequences of the use of this product in non-approved working environments may be:

User’s Manual vi

■ Interference with other devices or machines in the near surrounding area.

■ Malfunction of, or data loss from, this product caused by disturbances

generated by other devices or machines in the near surrounding area.

Therefore TOSHIBA strongly recommend that the electromagnetic compatibility of this product should be suitably tested in all non-approved working environments before use. In the case of automobiles or aircraft, the manufacturer or airline respectively should be asked for permission before use of this product.

Furthermore, for general safety reasons, the use of this product in environments with explosive atmospheres is not permitted.

Modem warning notice

This information is applicable to the models equipped with a built-in modem.

Conformity Statement

The equipment has been approved to [Commission Decision "CTR21"] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN).

However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.

In the event of problems, you should contact your equipment supplier in the first instance.

TECRA M11

Network Compatibility Statement

This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.

Germany ATAAB AN005, AN006, AN007, AN009,

AN010 and DE03,04,05,08,09,12,14,17

Greece ATAAB AN005,AN006 and GR01,02,03,04

Portugal ATAAB AN001, 005, 006, 007, 011 and P03,

04, 08, 10

Spain ATAAB AN005, 007, 012, and ES01

Switzerland ATAAB AN002

All other countries/regions ATAAB AN003, 004

Specific switch settings or software setup are required for each network, please refer to the relevant sections of the user guide for more details.

The hookflash (timed break register recall) function is subject to separate national type approvals. It has not been tested for conformity to national type regulations, and no guarantee of successful operation of that specific function on specific national networks can be given.

User’s Manual vii

TECRA M11

Following information is only valid for EU-member States:

Disposal of products

The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres.

The black bar indicates that the product was placed on the market after August 13, 2005.

By participating in separate collection of products and batteries, you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health.

For more detailed information about the collection and recycling programmes available in your country, please visit our website (http://eu.computers.toshiba-europe.com) or contact your local city office or the shop where you purchased the product.

Disposal of batteries and/or accumulators

The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste.

If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.

By participating in separate collection of batteries, you will help to assure the proper disposal of products and batteries and thus help to prevent potential negative consequences for the environment and human health.

These symbols may not stick depending on the country and region where you purchased.

User’s Manual viii

TECRA M11

Disposing of the computer and the computer's batteries

■ Discard this computer in accordance with applicable laws and

regulations. For further information, contact your local government.

■ This computer contains rechargeable batteries. After repeated use, the

batteries will finally lose their ability to hold a charge and you will need to replace them. Under certain applicable laws and regulation, it may be illegal to dispose of old batteries by placing them in the trash.

■ Please be kind to our shared environment. Check with your local

government authority for details regarding where to recycle old batteries or how to dispose of them properly. This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government.

REACH - Compliance Statement

The new European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007. Toshiba will meet all REACH requirements and is committed to provide our customers with information about the chemical substances in our products according to REACH regulation.

Please consult the following website

http://www.toshiba-europe.com/computers/info/reach for information about

the presence in our articles of substances included on the candidate list according to article 59(1) of Regulation (EC) No 1907/2006 ("REACH") in a concentration above 0.1 % weight by weight.

Following information is only for Turkey:

■ Compliant with EEE Regulations: Toshiba meets all requirements of

Turkish regulation 26891 “Restriction of the use of certain hazardous substances in electrical and electronic equipment”.

■ The number of possible pixel failures of your display is defined

according to ISO 13406-2 standards. If the number of pixel failures is less than this standard, they will not be counted as defect or failure.

■ Battery is a consumption product, since the battery time depends on the

usage of your computer. If the battery can not be charged at all, then it is a defect or failure. The changes in battery time is not a defect or failure.

User’s Manual ix

Optical disc drive safety instructions

Be sure to check the precautions at the end of this section.

■ The DVD-ROM/DVD Super Multi drive model employs a laser system.

To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.

■ Use of controls, adjustments or the performance of procedures other

than those specified may result in hazardous radiation exposure.

■ To prevent direct exposure to the laser beam, do not try to open the

enclosure.

TEAC

DVD-ROM drive DV-28S

DVD Super Multi with Double Layer Recording DV-W28S

TECRA M11

User’s Manual x

Panasonic Communications*

DVD Super Multi with Double Layer Recording UJ890

* "Panasonic Communications Co., Ltd." or "Panasonic System Networks

Co., Ltd."

TECRA M11

HITACHI-LG Data Storage

DVD Super Multi with Double Layer Recording GT20N

Hitachi-LG Data Storage, Inc. 22-23,KAIGAN 3-CHOME, MINATO-KU,TOKYO,108-0022 JAPAN

User’s Manual xi

Precautions

TECRA M11

CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.

User’s Manual xii

Preface

Congratulations on your purchase of the TECRA M11 computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing.

This manual tells how to set up and begin using your TECRA M11 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.

If you are a new user of computers or if you’re new to portable computing, first read over the Chapter 1, Getting Started and Chapter 3, Hardware,

Utilities and Options chapters to familiarize yourself with the computer’s

features, components and accessory devices. Then read Chapter 1,

Getting Started for step-by-step instructions on setting up your computer.

If you are an experienced computer user, please continue reading the preface to learn how this manual is organized, then become acquainted with this manual by browsing through its pages. Be sure to read the Special

features section in Chapter 3, Hardware, Utilities and Options to learn

about features that are uncommon or unique to this computer, as well as the section on Chapter 7, HW Setup, to understand how to setup and configure these features.

Read Chapter 3, Hardware, Utilities and Options if connecting optional products or external devices.

TECRA M11

Conventions

This manual uses the following formats to describe, identify, and highlight terms and operating procedures.

Abbreviations

On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary.

User’s Manual xiii

Icons

Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on.

Keys

The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, ENTER identifies the ENTER key.

Key operation

Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, CTRL + C means you must hold down CTRL and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.

ABC When procedures require an action such as

clicking an icon or entering text, the icon’s name or the text you are to type in is represented in the type face you see to the left.

Display

TECRA M11

ABC

Names of windows or icons or text generated by the computer that appears on its display screen is presented in the type face you see to the left.

Messages

Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below.

Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment.

Please read. A note is a hint or advice that helps you make best use of your equipment.

Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.

User’s Manual xiv

Terminology

This term is defined in this document as follows:

Start The word "Start" refers to the " " button in

Windows 7.

HDD or Hard disk drive

Some models are equipped with a "Solid State Drive (SSD)" instead of a hard disk drive.

In this manual, the word "HDD" or "Hard disk drive" also refers to the SSD unless otherwise stated.

TECRA M11

User’s Manual xv

General Precautions

TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.

Be certain to read the general precautions below and to note the cautions included in the text of the manual.

Provide adequate ventilation

■ Always make sure your computer and AC adaptor have adequate

ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep Mode). In this condition, observe the following:

■ Never cover your computer or AC adaptor with any object.

■ Never place your computer or AC adaptor near a heat source, such

as an electric blanket or heater.

■ Never cover or block the air vents including those located at the

base of the computer.

■ Always operate your computer on a hard flat surface. Using your

computer on a carpet or other soft material can block the vents.

■ Always provide sufficient space around the computer.

■ Overheating your computer or AC adaptor could cause system failure,

computer or AC adaptor damage or a fire, possibly resulting in serious injury.

TECRA M11

User’s Manual xvi

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.

Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat.

To keep your computer in prime operating condition, protect your work area from:

■ Dust, moisture, and direct sunlight.

■ Equipment that generates a strong electromagnetic field, such as

stereo speakers (other than speakers that are connected to the computer) or speakerphones.

■ Rapid changes in temperature or humidity and sources of temperature

change such as air conditioner vents or heaters.

■ Extreme heat, cold, or humidity.

■ Liquids and corrosive chemicals.

Stress injury

Carefully read the Instruction Manual for Safety and Comfort. It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. Instruction Manual for Safety and Comfort also includes information on work space design, posture and lighting that can help reduce physical stress.

TECRA M11

Heat injury

■ Avoid prolonged physical contact with the computer. If the computer is

used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.

■ If the computer has been used for a long time, avoid direct contact with

the metal plate supporting the various interface ports as this can become hot.

■ The surface of the AC adaptor can become hot when in use but this

condition does not indicate a malfunction. If you need to transport the AC adaptor, you should disconnect it and let it cool before moving it.

■ Do not lay the AC adaptor on a material that is sensitive to heat as the

material could become damaged.

Pressure or impact damage

Do not apply heavy pressure to the computer or subject it to any form of strong impact as this can damage the computer's components or otherwise cause it to malfunction.

User’s Manual xvii

ExpressCard overheating

Some ExpressCards can become hot during prolonged use which may result in errors or instability in the operation of the device in question. In addition, you should also be careful when you remove an ExpressCard that has been used for a long time.

Mobile phones

Please be aware that the use of mobile phones can interfere with the audio system. The operation of the computer will not be impaired in any way, but it is recommended that a minimum distance of 30cm is maintained between the computer and a mobile phone that is in use.

Instruction Manual for Safety and Comfort

All important information on the safe and proper use of this computer is described in the enclosed Instruction Manual for Safety and Comfort. Be sure to read it before using the computer.

TECRA M11

User’s Manual xviii

Getting Started

This chapter provides an equipment checklist, and basic information to start using your computer.

Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA.

Equipment checklist

Carefully unpack your computer, taking care to save the box and packaging materials for future use.

Hardware

Check to make sure you have all the following items:

■ TECRA M11 Portable Personal Computer

■ AC adaptor and power cord (2-pin plug or 3-pin plug)

■ Battery pack

■ Spare AccuPoint (pointing device) cap (Is included with some models)

Getting Started

Chapter 1

Documentation

■ TECRA M11 User’s Manual

■ TECRA M11 Quickstart

■ Instruction Manual for Safety and Comfort (included in User’s

Manual)

■ Warranty information (included in User's Manual)

If any of the items are missing or damaged, contact your dealer immediately.

User’s Manual 1-1

Software

The following Windows® operating system and utility software are preinstalled.

The availability of the software listed below is depending on the model you purchased.

■ Windows 7

■ TOSHIBA Value Added Package

■ TOSHIBA Recovery Media Creator

■ TOSHIBA DVD PLAYER

■ TOSHIBA Assist

■ TOSHIBA ConfigFree™

■ TOSHIBA HDD Protection

■ TOSHIBA Disc Creator

■ TOSHIBA Face Recognition

■ TOSHIBA eco Utility

■ TOSHIBA Bulletin Board

■ TOSHIBA ReelTime

■ Fingerprint Utility

■ Windows Mobility Center

■ Online Manual

Getting Started

■ All users should be sure to read the section Starting up for the first time.

■ Be sure to read the enclosed Instruction Manual for Safety and

Comfort for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer. By following the recommendations in it you may reduce your chance of developing a painful or disabling injury to your hand, arms, shoulders or neck.

This section provides basic information to start using your computer. It covers the following topics:

■ Connecting the AC adaptor

■ Opening the display

■ Turning on the power

■ Starting up for the first time

■ Turning off the power

■ Restarting the computer

■ System Recovery Options

■ Creating Recovery Media

■ Restoring the pre-installed software from the Recovery hard disk drive

■ Restoring the pre-installed software from your created Recovery Media

User’s Manual 1-2

■ Use a virus-check program and make sure it is updated regularly.

■ Never format storage media without checking its content - formatting

destroys all stored data.

■ It is a good idea to periodically back up the internal hard disk drive or

other main storage device to external media. General storage media is not durable or stable over long periods of time and under certain conditions may result in data loss.

■ Before you install a device or application, save any data in memory to

the hard disk drive or other storage media. Failure to do so may result in the loss of data.

Connecting the AC adaptor

Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power.

The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.

Getting Started

User’s Manual 1-3

Getting Started

■ Always use the TOSHIBA AC adaptor that was included with your

computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.

■ Never plug the AC adaptor into a power source that does not

correspond to both the voltage and the frequency specified on the regulatory label of the unit. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.

■ Always use or purchase power cables that comply with the legal

voltage and frequency specifications and requirements in the country of use. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region.

■ Do not use a 3-pin to 2-pin conversion plug.

■ When you connect the AC adaptor to the computer, always follow the

steps in the exact order as described in the User’s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.

■ Never place your computer or AC adaptor on a wooden surface,

furniture, or any other surface that could be marred by exposure to heat since the computer base and AC adaptor's surface increase in temperature during normal use.

■ Always place your computer or AC adaptor on a flat and hard surface

that is resistant to heat damage.

Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions.

User’s Manual 1-4

Getting Started

1. Connect the power cord to the AC adaptor.

Connecting the power cord to the AC adaptor (2-pin plug)

Connecting the power cord to the AC adaptor (3-pin plug)

Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model.

2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer.

1. DC IN 15V jack 2. DC output plug

Connecting the DC output plug to the computer

3. Plug the power cord into a live wall outlet - the Battery and DC IN indicators on the front of the computer should glow.

User’s Manual 1-5

Opening the display

The display panel can be opened to a wide range of angles for optimal viewing.

While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity.

1. Display panel

Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.

Getting Started

Opening the display panel

■ Be careful not to open the display panel too far as this could put stress

on the display panel’s hinges and cause damage.

■ Do not press or push on the display panel.

■ Do not lift the computer by the display panel.

■ Do not close the display panel with pens or any other objects left in

between the display panel and the keyboard.

■ When opening or closing the display panel, place one hand on the

palm rest to hold the computer in place and use the other hand to slowly open or close the display panel (Do not use excessive force when opening or closing the display panel).

User’s Manual 1-6

Turning on the power

This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Power-Up Modes for more information.

■ After you turn on the power for the first time, do not turn it off until you

have set up the operating system. Please refer to the section Starting

up for the first time for more information.

■ Volume cannot be adjusted during Windows Setup.

1. Open the display panel.

2. Press and hold the computer's power button for two or three seconds.

Getting Started

1. Power button

Turning on the power

Starting up for the first time

The Windows 7 Startup Screen will be the first screen displayed when you turn on the power. Follow the on-screen instructions on each screen in order to properly install the operating system.

When it is displayed, be sure to read the Software License Terms carefully.

User’s Manual 1-7

Turning off the power

The power can be turned off in one of three modes, either Shut Down Mode, Hibernation Mode or Sleep Mode.

Shut Down Mode

When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system's main screen the next time it is turned on.

1. If you have entered data, either save it to the hard disk drive or to other storage media.

2. Make sure all disk/disc activity has stopped before removing the CD/ DVD.

■ Make sure the Hard Disk Drive/Optical Disc Drive/eSATA indicators

are off. If you turn off the power while a disk (disc) is being accessed, you may lose data or damage the disk.

■ Never turn off the power while an application is running. Doing so

could cause loss of data.

■ Never turn off the power, disconnect an external storage device or

remove storage media during data read/write. Doing so can cause data loss.

3. Click Start.

4. Click the Shut down button ( ).

5. Turn off any peripheral devices connected to your computer.

Do not turn the computer or peripheral devices back on immediately - wait a short period to avoid any potential damage.

Getting Started

Sleep Mode

If you have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode. In this mode data is maintained in the computer's main memory so that when you turn on the power again, you can continue working right where you left off.

When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always completely shut down the computer. This includes turning off any wireless communication switches or devices, and canceling settings that reactivate the computer automatically, such as a timer recording function. Failure to completely shut down the computer in this way could allow the operating system to reactivate and run pre-programmed tasks or preserve unsaved data, which could interfere with aviation or other systems, possibly causing serious injury.

User’s Manual 1-8

Getting Started

■ Before entering Sleep Mode, be sure to save your data.

■ Do not install or remove a memory module while the computer is in

Sleep Mode. The computer or the memory module could be damaged.

■ Do not remove the battery pack while the computer is in Sleep Mode

(unless the computer is connected to an AC power source). Data in memory could be lost.

■ When the AC adaptor is connected, the computer will go into Sleep

Mode according to the settings in the Power Options (to access it, Start  Control Panel  System and Security  Power Options).

■ To restore the operation of the computer from Sleep Mode, press and

hold the power button or any key on the keyboard for a short amount of time. Please note that keyboard keys can only be used if the Wake-up on Keyboard option is enabled within the HW Setup utility.

■ If the computer enters Sleep Mode while a network application is

active, the application might not be restored when the computer is next turned on and the system returns from Sleep Mode.

■ To prevent the computer from automatically entering Sleep Mode,

disable Sleep Mode within the Power Options (to access it, Start  Control Panel  System and Security  Power Options).

■ To use the Hybrid Sleep function, configure it in the Power Options.

Benefits of Sleep Mode

The Sleep Mode feature provides the following benefits:

■ Restores the previous working environment more rapidly than does the

Hibernation Mode feature.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System Sleep Mode feature.

■ Allows the use of the panel power off feature.

Executing Sleep Mode

You can also enable Sleep Mode by pressing FN + F3 - please refer to Chapter 5, The Keyboard, for further details.

You can enter Sleep Mode in one of three ways:

■ Click Start, point to the arrow icon ( ) and then select

Sleep from the menu.

■ Close the display panel. Please note that this feature must be enabled

within the Power Options (to access it, click Start  Control Panel  System and Security  Power Options).

■ Press the power button. Please note that this feature must be enabled

within the Power Options (to access it, click Start  Control Panel  System and Security  Power Options).

User’s Manual 1-9

When you turn the power back on, you can continue where you left when you shut down the computer.

■ When the computer is in Sleep Mode, the power indicator will blink

orange.

■ If you are operating the computer on battery power, you can lengthen

the overall operating time by turning it off into Hibernation Mode Sleep Mode will consume more power while the computer is off.

Sleep Mode limitations

Sleep Mode will not function under the following conditions:

■ Power is turned back on immediately after shutting down.

■ Memory circuits are exposed to static electricity or electrical noise.

Hibernation Mode

The Hibernation Mode feature saves the contents of memory to the hard disk drive when the computer is turned off so that, the next time it is turned on, the previous state is restored. Please note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer.

■ Save your data. While entering Hibernation Mode, the computer saves

the contents of memory to the hard disk drive. However, for safety sake, it is best to save your data manually.

■ Data will be lost if you remove the battery or disconnect the AC

adaptor before the save is completed. Wait for the Hard Disk Drive/ Optical Disc Drive/eSATA indicator to go out.

■ Do not install or remove a memory module while the computer is in

Hibernation Mode. Data will be lost.

Getting Started

Benefits of Hibernation Mode

The Hibernation Mode feature provides the following benefits:

■ Saves data to the hard disk drive when the computer automatically

shuts down because of a low battery condition.

■ You can return to your previous working environment immediately when

you turn on the computer.

■ Saves power by shutting down the system when the computer receives

no input or hardware access for the time period set by the System Hibernate feature.

■ Allows the use of the panel power off feature.

User’s Manual 1-10

Getting Started

Starting Hibernation Mode

You can also enable Hibernation Mode by pressing FN + F4 - please refer to Chapter 5, The Keyboard, for further details.

To enter Hibernation Mode, follow the steps below.

1. Click Start.

2. Point to the arrow icon ( ) and then select Hibernate from the menu.

Automatic Hibernation Mode

The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid. In order to define these settings, you can follow the steps as described below:

1. Click Start and click the Control Panel.

2. Click System and Security and click Power Options.

3. Click Choose what the power button does or Choose what closing the lid does.

4. Enable the desired Hibernation Mode settings for When I press the power button and When I close the lid.

5. Click the Save changes button.

Data save in Hibernation Mode

When you turn off the power in Hibernation Mode, the computer will take a moment to save the current data in memory to the hard disk drive. During this time, the Hard Disk Drive/Optical Disc Drive/eSATA indicator will glow.

After you turn off the computer, and the content of memory has been saved to the hard disk drive, turn off the power to any peripheral devices.

Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.

Restarting the computer

Certain conditions require that you reset the computer, for example if:

■ You change certain computer settings.

■ An error occurs and the computer does not respond to your keyboard

commands.

If you need to restart the computer, there are three ways this can be achieved:

■ Click Start, point to the arrow icon ( ) and then select

Restart from the menu.

■ Press CTRL, ALT and DEL simultaneously (once) to display the menu

window, then select Restart from the Shut down options.

■ Press the power button and hold it down for five seconds. Once the

computer has turned itself off, wait between ten and fifteen seconds before turning the power on again by pressing the power button.

User’s Manual 1-11

System Recovery Options

There is a hidden partition allocated on the hard disk drive for the System Recovery Options.

This partition stores files which can be used to repair the system in the event of a problem.

The System Recovery Options feature will be unusable if this partition is deleted.

System Recovery Options

The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes tools to repair startup problems, run diagnostics or restore the system.

See the Windows Help and Support content for more information about Startup Repair.

The System Recovery Options can also be run manually to repair problems.

The procedure is as follows. Follow the instructions shown on the onscreen menu.

1. Turn off the computer.

2. While holding the F8 key, turn on the computer.

3. The Advanced Boot Options menu will be displayed. Use the arrow keys to select Repair Your Computer and press ENTER.

4. Follow the on-screen instructions.

Check your Windows® manual for more information on backing up your system (including the system image backup feature).

Getting Started

User’s Manual 1-12

System Recovery

This section describes the creation of Recovery Media and their use.

Creating Recovery Media

This section describes how to create Recovery Media.

■ Be sure to connect the AC adaptor when you create Recovery Media.

■ Be sure to close all other software programs except the Recovery

Media Creator.

■ Do not run software such as screen savers which can put a heavy load

on the CPU.

■ Operate the computer at full power.

■ Do not use power-saving features.

■ Do not write to the media when the virus check software is running.

Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background.

■ Do not use utilities, including those intended to enhance hard disk drive

access speed. They may cause unstable operation and damage data.

■ Do not shut down/log off or Sleep/Hibernate while writing or rewriting

the media.

■ Set the computer on a level surface and avoid places subjected to

vibrations such as airplanes, trains, or cars.

■ Do not use on an unstable surface such as a stand.

A recovery image of the software on your computer is stored on the hard disk drive, and can be copied to either DVD or USB Flash Memory by using the following steps:

1. Select either blank DVD or USB Flash Memory.

The application will allow you to choose from a variety of different media onto which the recovery image can be copied including DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW and USB Flash Memory.

■ Please note that some of the above media may not be compatible with

the optical disc drive installed into your computer. You should therefore verify the optical disc drive supports the blank media you have chosen before proceeding.

■ USB Flash Memory will be formatted and all the data in the USB Flash

Memory will be lost when proceeding.

2. Turn on your computer and allow it to load the Windows 7 operating system from the hard disk drive as normal.

3. Insert the media into the computer.

■ Insert the first blank disc into the optical disc drive tray, or Insert the

USB Flash Memory into one available USB port

4. Double click the Recovery Media Creator from Start Menu.

5. After Recovery Media Creator starts, select the type of media and the title you wish to copy, and then click the Create button.

Getting Started

User’s Manual 1-13

Getting Started

Restoring the pre-installed software from the Recovery hard disk drive

A portion of the total hard disk drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem.

If you subsequently set up your hard disk drive again, do not change, delete or add partitions in a manner other than specified in the manual, otherwise you may find that space for the required software is not available.

In addition, if you use a third-party partitioning program to reconfigure the partitions on your hard disk drive, you may find that it becomes impossible to setup your computer.

When the sound mute feature has been activated by pressing the FN + ESC key, be sure to disable this to allow sounds to be heard before starting the restore process. Please refer to Chapter 5, The Keyboard, for further details.

When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.

1. Turn off your computer.

2. While holding down 0 (zero) key on the keyboard, turn on your computer.

3. A menu will be displayed from which you should follow the on-screen instructions.

Restoring the pre-installed software from your created Recovery Media

If the pre-installed files are damaged, you are able to either use the Recovery Media you have created or the hard disk drive recovery process to restore the computer to the state it was in when you originally received it. To perform this restoration, follow the steps below:

When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.

1. Load the Recovery Media into the computer and turn off the computer's power.

2. While holding down F12 key on the keyboard, turn on your computer when the TOSHIBA Leading Innovation >>> logo screen appears, release the F12 key.

3. Use the up and down cursor key to select the appropriate option from the menu according to your actual recovery media. Please refer to the

Boot Priority section in Chapter 7, HW Setup for further information.

4. A menu will be displayed from which you should follow the on-screen instructions.

User’s Manual 1-14

Ordering Recovery Discs from TOSHIBA*

You can order Product Recovery discs for your notebook from the TOSHIBA Europe Backup Media Online Shop.

* Please note that this service is not free-of-charge.

1. Visit https://backupmedia.toshiba.eu on the Internet.

2. Follow the on-screen instructions.

You will receive your Recovery Discs within two weeks after placing your order.

Getting Started

User’s Manual 1-15

The Grand Tour

This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer.

Legal Footnote (Non-applicable Icons)

For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix G.

Please handle your computer carefully to avoid scratching or damaging the surface.

Front with the display closed

The following figure shows the computer’s front with its display panel in the closed position.

The Grand Tour

Chapter 2

3 4 5

1. Stereo speaker 4. Bridge media slot

2. Wireless communication switch* 5. Microphone*

3. Wireless indicators* 6. System indicators

Front of the computer with display panel closed

* Provided with some models Product appearance depends on the model you purchased.

User’s Manual 2-1

The Grand Tour

Stereo speakers The speakers emit sound generated by your

software as well as audio alarms, such as low battery condition, generated by the system.

Wireless communication switch

Slide this switch to the left to turn off Wireless LAN, Bluetooth

™

and Wireless WAN functions.

Slide it to the right to turn on the functions. Only some models are equipped with Bluetooth,

Wireless LAN and Wireless WAN functions.

■ Do not use the Wireless LAN (Wi-Fi®) or Bluetooth functionalities near

a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation.

■ Turn all wireless functionalities off when near a person who may have

a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any wireless functionality.

■ Always turn off wireless functionality if the computer is near automatic

control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury.

Wireless indicators These LED indicators allow you to monitor the

status of Bluetooth, Wireless LAN and Wireless WAN functions and are described in more detail within the Wireless indicators section.

Bridge media slot This slot lets you insert an SD™/SDHC™ memory

card, miniSD™/microSD™ Card, Memory Stick™ (PRO™/Duo™/PRO Duo™/Micro™), xD-Picture Card™ and MultiMediaCard™. Refer to the

Optional devices section in Chapter 3, Hardware, Utilities and Options.

Keep foreign metal objects, such as screws, staples and paper clips, out of the Bridge media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

Microphone A built-in microphone allows you to import and

record sounds for your application - please refer to the Sound System section in Chapter 4,

Operating Basics for more information.

Some models are equipped with a built-in microphone.

System indicators These LED indicators allow you to monitor the

status of various computer functions and are described in more detail within the System

indicators section.

User’s Manual 2-2

Left side

The Grand Tour

The following figure shows the computer’s left side.

1. Security lock slot 4. Mini DisplayPort

2. Cooling vents 5. Smart Card slot*

3. eSATA/USB combo port

2 3 4

The left side of the computer

* Provided with some models. Product appearance depends on the model you purchased.

Security lock slot A security cable can be attached to this slot and

then connected to a desk or other large object in order to deter theft of the computer.

Cooling vents The cooling vents help keep the processor from

overheating.

Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

eSATA/USB combo port

One eSATA/USB combo port, which complies to the USB 2.0 standard, is provided on the left hand side of the computer. This port has eSATA (External Serial ATA) function. The port with the icon ( ) has USB Sleep and Charge function.

Keep foreign metal objects, such as screws, staples and paper clips, out of the eSATA/USB combo port. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. In view of this it may be noted that some functions associated with a specific device might not operate properly.

User’s Manual 2-3

Right side

The Grand Tour

Mini DisplayPort This port is capable of driving resolutions up to

2560x1600. With a suitable adapter, Mini DisplayPort may be used to drive displays with a HDMI or DVI interface.

Smart Card slot This slot can accommodate a single Smart Card

device. Some models are equipped with a Smart Card slot.

Keep foreign metal objects, such as screws, staples and paper clips, out of the Smart Card slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

The following figure shows the computer’s right side.

1. ExpressCard slot 4. Optical disc drive*

2. Headphone jack 5. Universal Serial Bus (USB 2.0) port

3. Microphone jack

The right side of the computer

* Provided with some models. Product appearance depends on the model you purchased.

ExpressCard slot This slot allows you to install a single

ExpressCard/34 device.

Keep foreign metal objects, such as screws, staples and paper clips, out of the ExpressCard slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

Headphone jack A 3.5 mm mini headphone jack enables

connection of stereo headphones.

Microphone jack A 3.5 mm mini microphone jack enables

connection of a three-conductor mini jack for monaural microphone input.

User’s Manual 2-4

Back

The Grand Tour

Optical disc drive The computer may be configured with a DVD-

ROM or DVD Super Multi drive.

Universal Serial Bus (USB 2.0) port

One Universal Serial Bus port, which complies to the USB 2.0 standard, is provided on the right hand side of the computer.

Keep foreign metal objects, such as screws, staples and paper clips, out of the USB port. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.

The following figure shows the computer’s back.

1. Modem jack* 5. LAN jack

2. DC IN 15V jack 6. LAN active indicator (orange)

3. External monitor port 7. Link indicator (green)

4. Universal Serial Bus (USB 2.0) port

The back of the computer

42 3 5

* Provided with some models. Product appearance depends on the model you purchased.

Modem jack The modem jack lets you use a modular cable to

connect the modem directly to a telephone line. Some models are equipped with a modem jack.

User’s Manual 2-5

The Grand Tour

■ Connection to any communication line other than an analog phone line

could cause a PC system failure.

■ Connect the built-in modem only to ordinary analog phone lines.

■ Never connect the built-in modem to a digital line (ISDN).

■ Never connect the built-in modem to the digital connector on a public

telephone or to a digital private branch exchange (PBX).

■ Never connect the built-in modem to a key telephone system for

residences or offices.

■ Avoid using your computer modem with the telephone cable

connected during an electrical storm. There may be a remote risk of electric shock from lightning.

DC IN 15V jack The AC adaptor connects to this jack in order to

power the computer and charge its internal batteries. Please note that you should only use the model of AC adaptor supplied with the computer at the time of purchase - using the wrong AC adaptor can cause damage to the computer.

External monitor port This port provides 15-pin, analog VGA port.

This port allows you to connect an external monitor to the computer.

Universal Serial Bus (USB 2.0) port

One Universal Serial Bus port, which complies to the USB 2.0 standard, is provided on the back side of the computer.

LAN jack This jack lets you connect to a LAN. The adaptor

has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX). Some models are equipped with a Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Refer to Chapter 4, Operating

Basics, for details.

■ Do not connect any cable other than a LAN cable to the LAN jack. It

could cause damage or malfunction.

■ Do not connect the LAN cable to a power supply. It could cause

damage or malfunction.

LAN active indicator (orange)

This indicator may glow orange when the computer is connected to a LAN and the LAN is functioning properly.

Link indicator (green) This indicator may glow green when the

computer is connected to a LAN and the LAN is functioning properly.

User’s Manual 2-6

Underside

The following figure shows the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage.

* Provided with some models. Product appearance depends on the model you purchased.

The Grand Tour

1. Notches 4. Battery release latch

2. Docking port* 5. Battery pack

3. Memory module slot 6. Battery lock

The underside of the computer

Notches Notches on the computer engage hooks on the

TOSHIBA Express Port Replicator to ensure a secure connection.

Docking port This port enables connection of an optional

TOSHIBA Express Port Replicator described in Chapter 3, Hardware, Utilities and Options.

Some models are equipped with a Docking port.

■ Only the TOSHIBA Express Port Replicator can be used with this

computer. Do not attempt to use any other Port Replicator.

■ Keep foreign objects out of the docking port. A pin or similar object can

damage the computer's circuitry.

User’s Manual 2-7

The Grand Tour

Memory module slot The memory module slot allows for the

installation, replacement and removal of additional memory module.

Refer to the Additional memory module section in Chapter 3, Hardware, Utilities and Options.

Battery release latch Slide and hold this latch into its "Unlock" position

in order to release the battery pack for removal. For more detailed information on removing the battery pack please refer to Chapter 6, Power

and Power-Up Modes.

Battery pack The battery pack provides power to the computer

when the AC adaptor is not connected. For more detailed information on the use and operation of the battery pack please refer to Chapter 6, Power

and Power-Up Modes.

Battery lock Slide the battery lock to release the battery pack

ready for removal.

User’s Manual 2-8

Front with the display open

This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you.

The Grand Tour

1. Wireless LAN and Wireless WAN antennas (not shown)*

2. Web Camera* 11. Keyboard

3. Web Camera LED* 12. AccuPoint*

4. Display screen 13. AccuPoint control buttons*

5. Volume up/down button 14. Touch Pad

6. TOSHIBA Presentation button 15. Fingerprint Sensor*

7. eco button 16. Touch Pad control buttons

8. Power button 17. Bluetooth antenna (not shown)*

9. LCD Sensor switch (not shown)

10. Display hinges

The front of the computer with the display panel open

* Provided with some models. Product appearance depends on the model you purchased.

Wireless LAN antennas

Wireless WAN antennas

Some computers in this series are equipped with the Wireless LAN antennas.

Some computers in this series are equipped with the Wireless WAN antennas.

Web Camera LED The Web Camera LED glows when the Web

Camera is operating.

User’s Manual 2-9

The Grand Tour

Web Camera Web Camera is a device that allows you to

record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.

Enables the transmission of video and use of video chat via the internet using specialized applications.

Some models are equipped with a Web Camera. Please refer to the Web Camera section in

Chapter 4, Operating Basics.

Display screen Please be aware that, when the computer is

operating on the AC adaptor, the image displayed on the internal screen will be somewhat brighter than when it operates on battery power. This difference in brightness levels is intended to save power when operating on batteries. For more information on the computer's display, please refer to the Display

Controller and Video mode section in

Appendix B.

volume down button Press this button to decrease the volume.

volume up button Press this button to increase the volume.

TOSHIBA Presentation button

The TOSHIBA Presentation button has the same functionality as the Connect display button in the Mobility Center.

eco button Press this button to launch the TOSHBIA eco

Utility. This button changes "On" and "Off" of eco Mode. When eco Mode is "On", the icon turns green. When eco Mode is "Off", the icon turns gray.

The TOSHIBA eco Utility is not supported by Windows® XP operating system.

Power button Press this button to turn the computer's power on

and off.

User’s Manual 2-10

The Grand Tour

LCD Sensor switch This switch senses when the display panel is

either closed or opened and activates the Panel Power Off/On feature as appropriate. For example, when you close the display panel the computer enters Hibernation Mode and shuts itself down and then, when you next open the display, the computer will automatically start up and return you to the application you were previously working on.

You can specify within the Power Options. To access it, click Start  Control Panel  System and Security  Power Options.

Do not put any magnetic objects close to this switch as they may cause the computer to automatically enter Hibernation Mode and shut down even if the Panel Power Off feature is disabled.

Display hinges The display hinges allow the display panel to be

position at a variety of easy-to-view angles.

Keyboard The internal keyboard provides the embedded

numeric overlay keys, dedicated cursor control overlay keys, and and Keys. The keyboard is compatible with the IBM

enhanced keyboard. Refer to Chapter 5, The Keyboard, for details.

AccuPoint A pointer control device located in the center of

the keyboard is used to control the on-screen pointer. Refer to the Using the AccuPoint section in Chapter 4, Operating Basics.

Some models are equipped with a AccuPoint.

AccuPoint control buttons

Control buttons below the keyboard let you select menu items or manipulate text and graphics designated by the on-screen pointer. Refer to the Using the AccuPoint section in Chapter 4, Operating Basics.

Some models are equipped with a AccuPoint control buttons.

Touch Pad The Touch Pad located in the palm rest is used to

control the movement of the on-screen pointer. For more information, please refer to the Using

the Touch Pad section in Chapter 4, Operating Basics.

User’s Manual 2-11

Indicators

System indicators

The Grand Tour

Fingerprint Sensor This sensor enables you to enroll and recognize

a fingerprint. For detailed information on Fingerprint Sensor,

refer to Chapter 4, Using the Fingerprint Sensor. Some models are equipped with a Fingerprint

Sensor.

Touch Pad control buttons

Bluetooth antenna Some computers in this series are equipped with

This section explains indicator functions.

LED system indicators next to their respective icons, glow when specific computer operations are in progress.

The control buttons located below the Touch Pad allow you to select menu items or manipulate text and graphics as designated by the on-screen pointer.

a Bluetooth antenna.

System indicators

DC IN The DC IN indicator normally glows green when

Power The Power indicator normally glows green when

Battery The Battery indicator shows the condition of the

User’s Manual 2-12

power is being correctly supplied from the AC power adaptor. However, If the output voltage from the adaptor is abnormal, or if the computer's power supply malfunctions, this indicator will flash orange.

the computer is turned on. However, if you turn the computer off into Sleep Mode, this indicator will flash orange - approximately two second on, two seconds off - both while the system is shutting down and while it remains turned off.

battery's charge - green indicates the battery is fully charged, orange indicates the battery is charging, and flashing orange indicates a low battery condition. Please refer to Chapter 6,

Power and Power-Up Modes for more

information on this feature.

The Grand Tour

Hard Disk Drive/ Optical Disc Drive/ eSATA

Bridge media slot The Bridge media slot indicator glows green

The Hard Disk Drive/Optical Disc Drive/eSATA indicator glows green whenever the computer is accessing the built-in hard disk drive, optical disc drive or eSATA device.

when the computer is accessing the Bridge media slot.

Wireless indicators

Wireless indicators next to their respective icons, glow when specific computer operations are in progress.

Wireless indicators

Wireless communication

Wireless WAN The Wireless WAN indicator glows or blinks blue

The Wireless communication indicator blinks orange when the Bluetooth, Wireless LAN and Wireless WAN functions are turned on.

Only some models are equipped with Bluetooth and Wireless LAN functions.

when the Wireless WAN function is on. The indicator will glow or blink in order to indicate

the connection status of the Wireless WAN function.

A Wireless WAN module must be installed to use this function. Some models are equipped with a Wireless WAN module.

Keyboard indicators

The following figures show the positions of the CAPS LOCK indicator and the keypad overlay indicators which show the following conditions:

■ When the CAPS LOCK indicator glows, the keyboard will produce

capitals when any letter is typed.

■ When the Arrow Mode indicator glows, the keypad overlay allows you to

use cursor functions.

■ When the Numeric Mode indicator glows, the keypad overlay allows

you to enter numbers.

User’s Manual 2-13

The Grand Tour

1. CAPS LOCK indicator

CAPS LOCK indicator

CAPS LOCK This indicator glows green when letter keys are

locked into their uppercase format.

1. Arrow mode indicator 2. Numeric mode indicator

Keypad overlay indicators

Arrow mode When the Arrow mode indicator lights green,

you can use the gray labeled keys on the keypad overlay as cursor keys. Please refer to the

Keypad overlay section in Chapter 5, The Keyboard for more information.

Numeric mode When the Numeric mode indicator lights green,

you can use the gray labeled keys on the keypad overlay for number entry. Please refer to the

Keypad overlay section in Chapter 5, The Keyboard for more information.

User’s Manual 2-14

Optical disc drives

The computer may be installed with a DVD-ROM or DVD Super Multi drive. A Serial ATA interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.

Some models are equipped with an optical disc drive. For information on loading and unloading discs refer to the Using optical

disc drives section in Chapter 4, Operating Basics.

Region codes for DVD drives and media

DVD Super Multi drives and their associated media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video, make sure it matches your drive, otherwise it will not play properly.

Code Region

1 Canada, United States

2 Japan, Europe, South Africa, Middle East

3 Southeast Asia, East Asia

4 Australia, New Zealand, Pacific Islands, Central America,

South America, Caribbean

5 Russia, Indian Subcontinent, Africa, North Korea,

Mongolia

6 China

The Grand Tour

Writable discs

This section describes the types of writable CD/DVD discs. Check the specifications of your drive to see the types of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4,

Operating Basics.

CDs

■ CD-R discs can be written only once. The recorded data cannot be

erased or changed.

■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW

discs and ultra-speed CD-RW discs can be recorded more than once.

DVDs

■ DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs

can be written only once. The recorded data cannot be erased or changed.

■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than

once.

User’s Manual 2-15

Formats

The drives support the following formats.

DVD-ROM drive

The drive supports the formats CD-ROM, DVD-ROM, DVD-Video, CD-DA, CD-Text, Photo CD CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA) and Addressing Method 2.

(single/multi-session), CD-ROM Mode 1, Mode 2,

DVD Super Multi drive Double Layer

The drive supports the formats in addition to the DVD-ROM&CD-R/RW drive, and DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD-R DL (Format1), DVD+R DL.

Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable.

DVD-ROM drive

The full-size DVD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.

The read speed is slower at the center of a disc and faster at the outer edge.

DVD read 8 speed (maximum)

CD read 24 speed (maximum)

The Grand Tour

User’s Manual 2-16

DVD Super Multi drive Double Layer

The full-size DVD Super Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8cm (3.15") CD/ DVDs without using an adaptor.

The read speed is slower at the centre of a disc and faster at the outer edge.

DVD read 8 speed (maximum)

DVD-R write 8 speed (maximum)

DVD-R DL write 6 speed (maximum)

DVD-RW write 6 speed (maximum)

DVD+R write 8 speed (maximum)

DVD+R DL write 6 speed (maximum)

DVD+RW write 8 speed (maximum)

DVD-RAM write 5 speed (maximum)

CD read 24 speed (maximum)

CD-R write 24 speed (maximum)

CD-RW write 24 speed (maximum, Ultra-speed media)

AC adaptor

The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost all country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer.

To recharge the battery, simply connect the AC adaptor to a power source and to the computer. Please refer to Chapter 6, Power and Power-Up

Modes for further information.

The Grand Tour

The AC adaptor (2-pin plug)

User’s Manual 2-17

The Grand Tour

The AC adaptor (3-pin plug)

■ Depending on the model in question, either a 2-pin or 3-pin adaptor/

power lead will be bundled with the computer.

■ Do not use a 3-pin to 2-pin conversion plug.

■ The supplied power cord conforms to safety rules and regulations in

the region the product is bought and should not be used outside of this region. In order to use the adaptor/computer in other regions, you should please buy a power cord that conforms to the safety rules and regulations in that particular region.

Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.

User’s Manual 2-18

Hardware, Utilities and Options

Chapter 3

Hardware, Utilities and Options

Hardware

This section describes the hardware of your computer. The actual specifications may vary depending on the model you purchased.

Processor

CPU Your computer is equipped with one processor

and processor type varies depending on model. To check which type of processor is included in

your model, open the TOSHIBA PC Diagnostic Tool Utility by clicking Start  All Programs  TOSHIBA  Utilities  PC Diagnostic Tool.

Legal Footnote (CPU)

For more information on the CPU, please refer to the Legal Footnotes section in Appendix G.

Memory

Memory slots 1 GB, 2 GB or 4 GB memory modules can be

installed in the computer's two memory slots for a maximum of 8 GB system memory.

This computer can be equipped with memory modules of a maximum size of 8 GB. The actual amount of useable system memory will be less than the installed memory modules.

User’s Manual 3-1

Hardware, Utilities and Options

Video RAM The memory in a computer's graphics adaptor,

used to store the image displayed on a bitmap display.

The amount of Video RAM available is dependent on the computer's system memory.

Start  Control Panel  Appearance and Personalization  Display  Adjust resolution.

The amount of Video RAM can be verified by clicking the Advanced Settings button in the Screen Resolution window.

If your computer is configured with more than 3 GB memory, the memory might be displayed as approximately 3 GB only (depending on the computer’s hardware specifications).

This is correct because the operating system usually displays the available memory instead of the physical memory (RAM) built into the computer.

Various system components (like the video adapter’s GPU and PCI devices like Wireless LAN, etc.) require their own memory space. Since a 32-bit operating system cannot address more than 4 GB of memory, these system resources overlap the physical memory. It is a technical limitation that the overlapped memory is not available to the operating system. Even though some tools might display the actual physical memory built into your computer, the memory available to the operating system will still be approximately 3 GB only.

Computers configured with a 64-bit operating system can address 4 GB or more of system memory.

Legal Footnote (Memory (Main System))

For more information regarding Memory (Main System), please refer to the Legal Footnotes section in Appendix G.

Power

Battery pack The computer is powered by one rechargeable

lithium-ion battery pack.

Legal Footnote (Battery Life)

For more information regarding Battery Life, please refer to the Legal Footnotes section in Appendix G.

User’s Manual 3-2

Hardware, Utilities and Options

RTC battery The internal RTC battery backs up the Real Time

Clock (RTC) and calendar.

AC adaptor The AC adaptor provides power to the system

and recharges the batteries when they are low. It comes with a detachable power cord which will either have a 2-pin or 3-pin plug enclosure.

As the AC adaptor is universal, it can receive a range of AC voltages from 100 to 240 volts, however you should note that the output current varies among different models. Using the wrong adaptor can damage your computer. Refer to the

AC adaptor section in Chapter 2, The Grand Tour .

Disks

Hard disk drive or Solid state drive

■ In this manual, the word "HDD" or "Hard disk drive" also refers to the

SSD unless otherwise stated.

■ SSD is a large-capacity storage media which uses Solid-State Memory

in place of a magnetic disk of the hard disk.

Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the SSD may be vulnerable to data retention errors.

This computer is equipped with one of the following hard disk drive (HDD) types. The capacity of each hard disk drive model is different.

Some models are equipped with a "Solid State Drive (SSD)" instead of a hard disk drive.

■ HDD

■ 160GB

■ 250GB

■ 320GB

■ 500GB

■ SSD

■ 128GB

Please note that part of the hard disk or Solid state drive's overall capacity is reserved as administration space. Additional HDD/SSD drive sizes may be introduced.

Legal Footnote (Hard Disk Drive (HDD) Capacity)

For more information regarding Hard Disk Drive (HDD) Capacity, please refer to the Legal Footnotes section in Appendix G.

User’s Manual 3-3

Hardware, Utilities and Options

Optical disc drive

Drive The following optical disc drive may be pre-

installed in this computer.

■ DVD-ROM drive

■ DVD Super Multi drive Double Layer

2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.

Display

The computer's internal display panel supports high-resolution video graphics and can be set to a wide range of viewing angles for maximum comfort and readability.

Display panel 35.6cm (14.0") LCD screen, 16 million colors,

may be configured with the following resolution depending on the model you purchased:

■ HD, 1366 horizontal × 768 vertical pixels

■ HD+, 1600 horizontal × 900 vertical pixels

Legal Footnote (LCD)

For more information regarding the LCD, please refer to the Legal Footnotes section in Appendix G.

Graphics controller The graphics controller maximizes display

performance. Refer to Display Controller and

Video mode section in Appendix B for more

information.

Legal Footnote (Graphics Processor Unit ("GPU"))

For more information regarding the Graphics Processor Unit ("GPU"), please refer to the Legal Footnotes section in Appendix G.

Sound

Sound system The integrated sound system provides support

User’s Manual 3-4

for the computer's internal speakers and microphone, as allowing an external microphone and headphones to be connected via the appropriate jacks.

Hardware, Utilities and Options

Multimedia

Web Camera Web Camera is a device that allows you to

Some models are equipped with a Web Camera. Please refer to the Web Camera section in

Chapter 4, Operating Basics.

Communications

Modem The integrated modem provides capability for

LAN The computer has built-in support for Ethernet

Bluetooth Some computers in this series have Bluetooth

Wireless LAN Some computers in this series are equipped with

data and fax communications that support the V.90 (V.92) standards and includes a modem jack for connection to the telephone line. Please note that both the V.90 and V.92 standards are only supported in the USA, Canada, United Kingdom, France, Germany and Australia - only the V.90 standard is supported in other regions. You should also be aware that the speed of data and fax transfer will depend on the analog telephone line conditions.

Some models are equipped with the integrated modem.

LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T).

wireless communication function which eliminates the need for cables between electronic devices such as computers, printers and mobile phones. When it is enabled, Bluetooth provides the wireless personal area network environment which is safe and trustworthy, that is quick and easy.

a Wireless LAN module that is compatible with other Wireless LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard.

User’s Manual 3-5

Legal Footnote (Wireless LAN)

For more information regarding Wireless LAN, please refer to the Legal Footnotes section in Appendix G.

Wireless WAN Some computers in this series are equipped with

Special features

The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use.

Access each function using the following procedures. *1 To access the Power Options, click Start  Control Panel  System

and Security  Power Options.

eco button Press this button to launch the TOSHBIA eco

TOSHIBA Presentation button

Hot keys Hot keys are specific key combinations that let

Display automatic power off

HDD automatic power

off

System automatic Sleep/Hibernation

Mode

Keypad overlay A ten-key numeric keypad is integrated into the

Hardware, Utilities and Options

a Wireless WAN module.

Utility. This button changes "On" and "Off" of eco Mode. When eco Mode is "On", the icon turns green. When eco Mode is "Off", the icon turns gray.

The TOSHIBA Presentation button has the same functionality as the Connect display button in the Mobility Center.

you quickly change the system configuration directly from the keyboard without running a system program.

This feature automatically cuts off power to the computer's display panel when there is no keyboard input for a specified time, with power being restored the next time a key is pressed. This can be specified in the Power Options.

This feature automatically cuts off power to the hard disk drive when it is not accessed for a specified time, with power being restored when the hard disk drive is next accessed. This can be specified in the Power Options.

This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time. This can be specified in the Power Options.

keyboard. Please refer to the Keypad overlay section in Chapter 5, The Keyboard, for information on using this feature.

User’s Manual 3-6

Hardware, Utilities and Options

Power on password Two levels of password security, supervisor and

user, are available to prevent unauthorized access to your computer.

Intelligent power

supply

A microprocessor in the computer's intelligent power supply detects the battery's charge, automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor. This can be specified in the Power Options.

Battery save mode

This feature lets you configure the computer in order to save battery power. This can be specified in the Power Options.

Panel power on/off

This feature automatically turns power to the computer off when the display panel is closed, and turns it back on when the display panel is opened. This can be specified in the Power Options.

Low battery automatic Hibernation Mode

When battery power is exhausted to the point that computer operation cannot be continued, the

system automatically enters Hibernation Mode and shuts itself down. This can be specified in the Power Options.

Heat dispersal

To protect against overheating, the processor has an internal temperature sensor so that, if the computer's internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. This can be specified in the Power Options.

TOSHIBA HDD Protection

This feature uses the acceleration sensor built in the computer to detect vibration and shocks, and automatically moves the hard disk drive's read/ write head to a safe position in order to reduce the risk of damage that could be caused by headto-disk contact. Refer to the Using the Hard Disk

Drive (HDD) Protection section in Chapter 4, Operating Basics, for more details.

■ The TOSHIBA HDD Protection function does not guarantee that the

hard disk drive will not be damaged.

■ TOSHIBA HDD Protection cannot be used in models that are equipped

with SSD.

User’s Manual 3-7

Hardware, Utilities and Options

Hibernation Mode This feature lets you turn off the power to the

computer without exiting from your software. The contents of main memory are automatically saved to the hard disk drive so that when you next turn the power on again, you can continue working right where you left off. Refer to the

Turning off the power section in Chapter 1, Getting Started, for more details.

Sleep Mode If you have to interrupt your work, you can use

this feature to allow you to turn off power to the computer without exiting from your software. Data is maintained in the computer's main memory so that when you next turn on the power, you can continue working right where you left off.

USB Sleep and Charge function

This feature allows you to charge USBcompatible external devices such as mobile phones or portable digital music players via the USB port when your computer is in Sleep Mode, Hibernation Mode or in the shutdown state.

This function is worked by the USB Sleep and Charge Utility. For more information, please refer to the Using the TOSHIBA USB Sleep and

Charge Utility section in Chapter 4, Operating Basics.

USB Wakeup function This function restores the computer from Sleep

Mode depending on the external devices connected to the USB ports.

For example, if a mouse or USB keyboard is connected to a USB port, clicking the mouse button or pressing the keyboard will wakeup the computer.

TOSHIBA PC Health Monitor

The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption, battery health and system cooling, informing you of significant system conditions. This application recognizes the system and individual component serial numbers and will track specific activities related to their usage.

Refer to Appendix F, TOSHIBA PC Health

Monitor.

User’s Manual 3-8

Utilities and Applications

This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, you may refer to each utility's online manual, help files or README.TXT file (if applicable).

TOSHIBA Power Saver

TOSHIBA Button Support

TOSHIBA Button Support cannot be used in models that are not equipped with eco button and TOSHIBA Presentation button.

Hardware, Utilities and Options

TOSHIBA Power Saver provides you with the features of more various power supply managements.

This utility controls the following computer button functions.

■ eco button

■ TOSHIBA Presentation button

The starting application from the button can be changed.

TOSHIBA Zooming Utility

TOSHIBA PC Diagnostic Tool

TOSHIBA Password Utility

TOSHIBA Flash Cards The TOSHIBA Flash Cards provide a quick way

HW Setup This utility allows you to customize your

This utility allows you to enlarge or reduce the icon size on the Windows Desktop, or the zoom factor associated with specific supported applications.

The TOSHIBA PC Diagnostic Tool will display basic system configuration information and allow the functionality of some of the computer's builtin hardware devices to be tested.

The TOSHIBA Password utility allows you to set a password in order to restrict access to the computer.

to modify selected system functions and to launch applications.

■ Hot key function

■ TOSHIBA utility launcher function

hardware settings according to the way you work with the computer and the peripherals you use.

User’s Manual 3-9

Hardware, Utilities and Options

TOSHIBA Accessibility

The TOSHIBA Accessibility utility provides support to movement impaired users when they need to use the TOSHIBA Hot-key functions. In use, the utility allows you to make the FN key 'sticky', that is you can press it once, release it, and they press one of the "Function" keys in order to access its specific function. When set, the FN key will remain active until another key is pressed.

Fingerprint Utility This product has a fingerprint utility installed for

the purpose of enrolling and recognizing fingerprints which can then be linked to a username and password in order to remove the need to input these details from the keyboard. Just by swiping an enrolled finger against the fingerprint sensor, the following functions will be enabled:

■ Logon to Windows and access a security

enabled homepage through Internet Explorer.

■ Files and folders can be encrypted/decrypted

and third party access to them is prevented.

■ Disable the password-protected screen-saver

when returning from a power-saving mode such as Sleep Mode.

■ Authentication of the User Password (and, if

applicable, the HDD (Hard Disk Drive) Password) when booting up the computer (Power-on Security).

■ Single Sign-on feature

Fingerprint security cannot be used in models that do not have a fingerprint module installed.

TOSHIBA Face Recognition

TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows. If the verification is successful, the user will be logged into Windows automatically. The user can thus avoid having to enter a password or the like, which makes the login process easier.

For more information, please refer to the Using

the TOSHIBA Face Recognition section in

Chapter 4, Operating Basics.

User’s Manual 3-10

Hardware, Utilities and Options

TOSHIBA DVD PLAYER

This software is provided for playback of DVD Video depending on the model you purchased.

It has an on-screen interface and functions. Click

Start  All Programs  TOSHIBA DVD PLAYER  TOSHIBA DVD PLAYER.

For details on how to use TOSHIBA DVD PLAYER, see the help file.

■ Frame dropping, audio skipping or out of synch audio and video may

occur during playback of some DVD Video titles.

■ Make sure to connect the computer's AC adaptor when playing a DVD

Video. Power-saving features may interfere with smooth playback.

■ If you see the screen blinking while playing DVD with subtitle on at

Media Player, please use TOSHIBA DVD PLAYER or Media Center to play DVD.

Bluetooth Stack for Windows by Toshiba

This software enables communication between the computer and external Bluetooth devices such as printers and mobile phones.

Bluetooth functions cannot be used in models that do not have a Bluetooth module installed.

TOSHIBA Assist TOSHIBA Assist is a graphical user interface that

provides access to specific tools, utilities and applications that make the use and configuration of the computer easier.

TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities that

improve the ease and control of communication devices and network connections, help in the identification of communication problems and allow the creation of profiles if you need to switch between different locations and communication networks. To access this utility, click Start  All

Programs  TOSHIBA  ConfigFree.

TOSHIBA Mic Effect TOSHIBA Mic Effect provides you the Echo

Canceller and the Microphone Array functions. For more instructions for this software, refer to

the Sound System section in Chapter 4,

Operating Basics.

User’s Manual 3-11

Hardware, Utilities and Options

TOSHIBA eco Utility This PC is equipped with "eco mode". This mode

slightly lowers performance of some devices to reduce electric power consumption. You can realize measurable power savings by using it continuously. TOSHIBA eco Utility helps you monitor your power savings by showing approximate real time power consumption. Furthermore, it shows approximate accumulated power consumption and approximate accumulated power savings when using eco mode daily, weekly, and monthly. You can track power savings by using eco mode continuously.

TOSHIBA Disc Creator

You can create CDs and DVDs in a number of formats including audio CDs that can be played on a standard CD player, and data CD/DVDs which can store copies of the files and folders on your computer's hard disk drive. This software can be used on models with a DVD Super Multi drive.

To start this utility, click Start  All Programs 

TOSHIBA  CD&DVD Applications  Disc Creator.

TOSHIBA DVD-RAM Utility

This utility has the function of Physical Format and Write-Protect to DVD-RAM. This utility is contained the setup module of TOSHIBA Disc Creator. To start this utility, click Start  All

Programs  TOSHIBA  CD&DVD Applications  DVD-RAM Utility.

TOSHIBA HDD/SSD Alert Utility

This utility includes wizard functions to monitor the Disk Drive operating status and execute the system backup.

To access the utility, click Start  All

Programs  TOSHIBA  Utilities  HDD SSD Alert.

TOSHIBA Service Station

This application allows your computer to automatically search for TOSHIBA software updates or other alerts from TOSHIBA that are specific to your computer system and its programs. When enabled, this application periodically transmits to our servers a limited amount of system information, which will be treated in strict accordance with the rules and regulations as well as applicable data protection law.

To access this utility, click Start

 All Programs  TOSHIBA  Utilities  Service Station.

User’s Manual 3-12

Hardware, Utilities and Options

Display Rotation Settings

Windows Mobility Center

TOSHIBA USB Sleep and Charge Utility

Trusted Platform Module (TPM)

This utility allows you to quickly rotate the Windows Desktop by either 0 degrees and 180 degrees. In use you are able to perform a rotation function by pressing either CTRL + ALT + Up Arrow ( ) to rotate 0 degrees or CTRL + ALT + Down Arrow ( ) to rotate 180 degrees - in a multi-monitor setup, the display that contains the cursor will be affected by these changes.

Mobility Center is a utility for accessing several mobile PC settings quickly in one window. A default maximum of eight tiles are provided by the operating system, and the additional two tiles are added to your Mobility Center.

■ Lock Computer:

This can be used to lock your computer without turning it off. This has the same function as selecting Lock from the Start menu (click Start, point to the arrow icon ( ) and then select Lock from the menu).

■ TOSHIBA Assist:

This can be used to open TOSHIBA Assist if it is already installed in your computer.

This utility is able to either enable or disable the USB Sleep and Charge function.

Shows the positions of USB ports that support the USB Sleep and Charge function and displays the battery's remaining capacity.

To start this utility, click Start  All Programs 

TOSHIBA  Utilities  USB Sleep and Charge.

The TPM (Trusted Platform Module) is a security encryption device for the hard disk drive.

BIOS setup and Infineon TPM Software Professional Package must be configured in order to use TPM.

To enable TPM through the BIOS setup:

1. Turn on the computer. Press the F2 key When the TOSHIBA Leading Innovation >>> screen appears.

2. Set the TPM in the Security tab to Enabled.

3. Press the F10 key.

4. Press the Y key to accept the changes. The computer will restart.

In order to change the TPM setting when the Hide TPM setting is currently set to Yes, switch the Hide TPM setting from Yes to No.

User’s Manual 3-13

Optional devices

Optional devices can expand the computer's capabilities and its versatility. This section describes the connection or installation of the following devices:

Cards/memory

■ ExpressCard (ExpressCard/34 only)

■ Smart Card

■ Bridge media slot

■ Secure Digital™ (SD) Card (SD memory card, SDHC memory card,

miniSD Card, microSD Card)

■ Memory Stick (Memory Stick, Memory Stick PRO, Memory Stick

Duo, Memory Stick PRO Duo, Memory Stick Micro)

■ xD picture card

■ MultiMediaCard

■ Additional memory module

Peripheral devices

■ External monitor

■ eSATA devices

■ Mini DisplayPort

■ TOSHIBA Express Port Replicator

Hardware, Utilities and Options

Other

■ Security lock

User’s Manual 3-14

ExpressCard

The computer is equipped with a single ExpressCard slot into which any ExpressCard/34 device that meets industry standards, either manufactured by TOSHIBA or another vendor, can be installed. The slot supports hot plug connection and utilizes the PCI Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5Gbps.

Inserting an ExpressCard

The Windows hot-install feature allows you to insert ExpressCards while the computer is turned on.

Do not insert an ExpressCard while the computer is in Sleep Mode or Hibernation Mode as you may find that some cards do not work properly.

To insert an ExpressCard, follow the steps as detailed below:

1. Press the Dummy card in order to eject the Dummy card partially out of the computer.

2. Grasp the Dummy card and draw it.

3. Insert the ExpressCard into the ExpressCard slot on the right side of the computer.

4. Press the ExpressCard gently to ensure a firm connection is made.

Hardware, Utilities and Options

1. ExpressCard slot 2. ExpressCard

Inserting the ExpressCard

5. After inserting the ExpressCard you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct.

User’s Manual 3-15

Hardware, Utilities and Options

Removing an ExpressCard

To remove an ExpressCard, follow the steps as detailed below.

1. Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar.

2. Point to ExpressCard and click the left Touch Pad control button.

3. Press the ExpressCard in order to eject the ExpressCard partially out of the computer.

4. Grasp the ExpressCard and remove it.

1. ExpressCard

Removing the ExpressCard

5. Insert the Dummy card into the ExpressCard slot.

When you do not use an ExpressCard, please be sure to insert a Dummy card.

Smart Card

A Smart Card is a credit card sized plastic card. An extremely thin integrated circuit (IC chip) is embedded into the card on which information can be recorded. These cards can be used for a wide variety of applications including telephone related and electronic monetary payments.

This section contains information on the proper use of the Smart Card slot, and it is strongly recommended that you read it before operating the computer.

Some models are equipped with a Smart Card slot.

Your computer supports ISO7816-3 asynchronous cards (support protocols are T=0 and T=1) with a working voltage of 5V.

User’s Manual 3-16

Hardware, Utilities and Options

Inserting a Smart Card

The Smart Card slot is located on the left side of the computer. The Windows hot-install feature allows you to insert a Smart Card while the computer is turned on.

To install a Smart Card, follow the steps as detailed below:

1. Insert the Smart Card into the Smart Card slot with the metal connectors facing up.

2. Press the Smart Card gently to ensure a firm connection is made. The computer will identify the Smart Card and display an icon in the Windows Taskbar.

■ When inserting a Smart Card into the Smart Card slot, make sure to

confirm that the card is oriented correctly before inserting.

■ Insert the Smart Card until it reaches the end of the Smart Card slot.

There will be about 2cm of the Smart Card sticking out of the Smart Card slot. Do not attempt to insert it further.

■ Always remove the Smart Card from the Smart Card slot before

moving the computer.

■ Remove the Smart Card after use.

Failure to follow these instructions may result in damage to the computer and/or damage to the Smart Card.

1. Smart Card

Inserting a Smart Card

3. After inserting the Smart Card, you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct.

User’s Manual 3-17

Hardware, Utilities and Options

Removing a Smart Card

To remove a Smart Card, follow the steps as detailed below:

1. Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar.

■ Before removing the Smart Card, confirm that the Smart Card is not

working with any program or system.

■ Be careful not to bend the Smart Card while removing it from the

computer.

2. Point to Smart Card and click the left Touch Pad control button.

3. Grasp the Smart Card and remove it.

1. Smart Card

Removing a Smart Card

User’s Manual 3-18

Bridge media slot

The computer is equipped with a Bridge media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants.

Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or Keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.

■ This Bridge media slot supports the following memory media.

■ Secure Digital (SD) Card (SD memory card, SDHC memory

■ Memory Stick (Memory Stick, Memory Stick PRO, Memory

■ xD picture card

■ MultiMediaCard (MMC™)

■ Please note that an adaptor is required to use miniSD/microSD Card.

■ Please note that an adaptor is required to use Memory Stick Duo,

Memory Stick PRO Duo and Memory Stick Micro.

■ Please note that not all memory media have been tested and verified

to work correctly. Therefore, it is not possible to guarantee that all memory media will operate properly.

■ The slot does not support Magic Gate functions.

Hardware, Utilities and Options

card, miniSD Card, microSD Card)

Stick Duo, Memory Stick PRO Duo, Memory Stick Micro)

Secure Digital (SD) Card

Memory Stick

Examples of memory media

User’s Manual 3-19

microSD card adaptor and microSD card

xD picture card

MultiMediaCard

(MMC)

Hardware, Utilities and Options

Memory media

This section provides the important safety precautions in order to handle your memory media.

Points to note about the SD/SDHC memory card

SD/SDHC memory cards comply with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music. For this reason, you cannot copy or playback protected material on another computer or other device, and you may not reproduce any copyrighted material except for your personal enjoyment.

Below is a simple explanation for distinguishing SD memory cards from SDHC memory cards.

■ SD and SDHC memory cards appear the same externally. However, the

logo on SD and SDHC memory cards is different, so pay careful attention to the logo when purchasing.

■ The SD memory card logo is ( ).

■ The SDHC memory card logo is ( ).

■ The maximum capacity of SD memory cards is 2GB. The maximum

capacity of SDHC memory cards is 32GB.

Card Type

SD 8MB, 16MB, 32MB, 64MB, 128MB, 256MB,

SDHC 4GB, 8GB, 16GB, 32GB

Capacities

512MB, 1GB, 2GB

Memory media format

New media cards are formatted according to specific standards. If you wish to reformat a media card, be sure to do so with a device that uses media cards.

Formatting an SD/SDHC memory card

SD/SDHC memory cards are sold already formatted in conformity to specific standards. If you reformat an SD/SDHC memory card, be sure to reformat it with a device such as digital camera or digital audio player that uses the SD/SDHC memory cards, not with the format command provided within Windows.

Should you need to format all areas of the memory card,including the protected area,you will need to obtain an appropriate application that applies the copy protection system.

User’s Manual 3-20

Hardware, Utilities and Options

Media care

Observe the following precautions when handling the card.

Card care

■ Do not twist or bend cards.

■ Do not expose cards to liquids or store in humid areas or lay media

close to containers of liquid.

■ Do not touch the metal part of a card or expose it to liquids or let it get

dirty.

■ After using card, return it to its case.

■ The card is designed so that it can be inserted only one way. Do not try

to force the card into the slot.

■ Do not leave a card partially inserted in the slot. Press the card until you

hear it click into place.

Memory card care

■ Set the write-protect switch to the lock position, if you do not want to

record data.

■ Memory cards have a limited lifespan, so it is important to backup

important data.

■ Do not write to a card if the battery power is low. Low power could affect

writing accuracy.

■ Do not remove a card while read/write is in progress.

For more details on using memory cards, see manuals accompanying the cards.

About the write-protect

The following memory media have a function for protect.

■ SD Card (SD memory card, SDHC memory card)

■ Memory Stick (Memory Stick, Memory Stick PRO, Memory Stick Duo,

Memory Stick PRO Duo, Memory Stick Micro)

Set the write-protect switch to the lock position, if you do not want to record data.

User’s Manual 3-21

Hardware, Utilities and Options

Inserting a memory media

The following instructions apply to all types of supported media devices. To insert a memory media, follow the steps as detailed below:

1. Turn the memory media so that the contacts (metal areas) are face down.

2. Insert the memory media into the Bridge media slot on the front of the computer.

3. Press the memory media gently to ensure a firm connection is made.

1. Bridge media slot 2. Memory media

Inserting a memory media

■ Make sure memory media is oriented properly before you insert it. If you

insert the media in wrong direction, you may not be able to remove it.

■ When inserting memory media, do not touch the metal contacts. You

could expose the storage area to static electricity, which can destroy data.

■ Do not turn the computer off or switch to Sleep Mode or Hibernation

Mode while files are being copied - doing so may cause data to be lost.

Removing a memory media

The following instructions apply to all types of supported media devices. To remove a memory media, follow the steps as detailed below:

1. Open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar.

2. Point to memory media and click the left Touch Pad control button.

3. Press the memory media to partially extend it out of the computer.

4. Grasp the media and remove it.

1. Bridge media slot 2. Memory media

Removing memory media

User’s Manual 3-22

Hardware, Utilities and Options

■ Make sure the Bridge Media slot indicator is out before you remove

the memory media or turn off the computer’s power. If you remove the memory media or turn off the power while the computer is accessing the memory media, you may lose data or damage the media.

■ Do not remove the memory media while the computer is in Sleep or

Hibernation Mode. The computer could become unstable or data in the memory media could be lost.

■ Do not remove only the Memory Stick Duo/Memory Stick PRO Duo/

Memory Stick Micro/miniSD/microSD Card while leaving the adaptor in the Bridge Media slot.

Additional memory module

You can install additional memory into the computer in order to increase the amount of system memory that is available. This section describes how to install and remove optional memory modules.

■ You should place a mat beneath the computer in order to prevent the

computer's lid from becoming scratched or damaged when you are installing/replacing the memory module. In this instance you should avoid mats that are made of materials that hold or generate static electricity.

■ When installing or removing a memory module, you must ensure that

you do not touch any other internal areas of the computer.

■ Insert the two memory modules into Slot A and Slot B respectively.

The computer will operate in dual channel mode. You can access the inserted memory modules efficiently in dual channel.

■ Use only memory modules approved by TOSHIBA.

■ Do not try to install or remove a memory module under the following

conditions. a. The computer is turned on. b. The computer was shut down in either Sleep or Hibernation Mode. c. Wake-up on LAN is enabled. d. The wireless communication switch is turned on. e. USB Sleep and Charge function is enabled.

■ Be careful not to let screws or other foreign matter fall into the

computer. It could cause malfunction or electric shock.

■ Additional memory module is a precision electronic component that

may be fatally damaged by static electricity. Since the human body can carry static electricity, it is important that you discharge yourself before touching or installing any additional memory modules. To discharge your body’s static electricity, simply touch any metal close to you with bare hands.

User’s Manual 3-23

Hardware, Utilities and Options

Use a point size 0 Phillips screwdriver to remove and fasten the screws the use of an incorrect screwdriver can damage the screw heads.

Installing a memory module

To install a memory module, follow the steps as detailed below:

1. Shut down the computer - make sure the Power indicator is off (refer to the Turning off the power section in Chapter 1, Getting Started if required).

2. Remove the AC adaptor and all cables and peripherals connected to the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack (refer to

Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required).

5. Loosen the screw securing the memory module cover in place - please note that the screw is attached to the cover in order to prevent it from being lost.

Use a point size 0 Phillips screwdriver.

6. Slide your fingernail or a thin object under the cover and lift it off.

1. Memory module cover 2. Screw

Removing the memory module cover

7. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place.

User’s Manual 3-24

Hardware, Utilities and Options

1. Notch 3. Slot A

2. Slot B

Seating the memory module

Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.

Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.

■ Align the grooves along the edges of the memory module with the

locking tabs on the connector and insert the module into the connector firmly - if you find it difficult to install the memory module, gently prise the locking tabs outwards using the tip of your finger.

Please also ensure that you hold the memory module along its left and right hand edges - the edges with the grooves in.

8. Seat the memory module cover in place and secure it with the screw.

Take care to ensure that the memory module cover is firmly closed.

1. Memory module cover 2. Screw

Seating the memory module cover

User’s Manual 3-25

Hardware, Utilities and Options

9. Install the battery pack - refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required.

10. Turn your computer over.

11. Turn the computer on and make sure the added memory is recognized to confirmed it, Start  Control Panel  System and Security 

System icon.

Removing a memory module

To remove the memory module, follow the steps as detailed below:

1. Shut down the computer - make sure the Power indicator is off (refer to the Turning off the power section in Chapter 1, Getting Started if required).

2. Remove the AC adaptor and all cables and peripherals connected to the computer.

3. Close the display panel.

4. Turn the computer upside down and remove the battery pack (refer to

Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required).

5. Loosen the screw securing the memory module cover in place - please note that the screw is attached to the cover in order to prevent it from being lost.

6. Slide your fingernail or a thin object under the cover and lift it off.

7. Push the latches away from the module in order to release it - a spring will force one end of the module up at an angle.

8. Grasp the module by its edges and remove it from the computer.

■ If you use the computer for a long time, the memory modules and the

circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them.

■ Do not touch the connectors on the memory module or on the

computer. Debris on the connectors may cause memory access problems.

User’s Manual 3-26

Hardware, Utilities and Options

1. Latches

Removing the memory module

9. Seat the memory module cover in place and secure it with the screw.

Take care to ensure that the memory module cover is firmly closed.

10. Install the battery pack - refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required.

11. Turn your computer over.

User’s Manual 3-27

External monitor

An external analog monitor can be connected to the external monitor port on the computer. To connect a monitor, follow the steps as detailed below:

Connecting the monitor cable

1. Turn the computer's power off.

2. Connect the monitor cable to the external monitor port and tighten the screws on the left and right hand side of the connector as required.

1. External monitor port 2. Monitor cable

Connecting the monitor cable to the external monitor port

3. Turn the external monitor's power on.

4. Turn the computer's power on.

When you turn on the power, the computer will automatically recognize the monitor and determine whether it is a color or monochrome device. In the event that you find that there are issues getting an image displayed on the correct monitor, you should consider using the FN + F5 hot key to change the display settings (if you then disconnect the external monitor before you turn the computer's power off, be sure to press FN + F5 hot key again to switch to the internal display).

Please refer to Chapter 5, The Keyboard, for further details on using hot keys to change the display setting.

Do not disconnect the external monitor while in Sleep or Hibernation Mode. Turn off the computer before disconnecting the external monitor.

When displaying desktop at external analog monitor, desktop is sometimes displayed on the center of the monitor with black bars around desktop (with small size).

At that time, please read the manual of the monitor and set the display mode which is supporting at the monitor. Then it will be displayed with suitable size with correct aspect ratio.

Hardware, Utilities and Options

User’s Manual 3-28

Hardware, Utilities and Options

Mini DisplayPort

With a suitable adapter (such as the "Mini DisplayPort to DisplayPort cable", "Mini DisplayPort to HDMI adapter" or "Mini DisplayPort to DVI adapter"), this port enables you to connect an external monitor.

Connecting the Mini DisplayPort

1. Plug one end of the adapter cable into the port (DisplayPort, HDMI port or DVI port) on your external monitor.

2. Turn on the external monitor.

3. Plug the other end of the adapter cable (Mini DisplayPort connector side) into the Mini DisplayPort on your computer.

1. Mini DisplayPort 2. Mini DisplayPort connector

Connecting the Mini DisplayPort

■ "Mini DisplayPort to DsiplayPort cable", "Mini DisplayPort to HDMI

adapter" or "Mini DisplayPort to DVI adapter" is not supplied with your computer. This product may be purchased from the retailer.

■ As the port operation has not been confirmed, some monitors may not

function properly.

When you change the display output device by hot key like FN + F5, the playback device may not switch automatically. In this case, in order to set the playback device to the same device as the display output device, please adjust the playback device manually by the following steps:

1. Click Start  Control Panel  Hardware and Sound  Sound.

2. In the Playback tab, select the playback device which you want to switch to.

■ To use the internal speakers on your computer, select Speakers.

■ To use the television or the external monitor that you have connected

to the computer, select a different playback device.

3. Click the Set Default button.

4. Click OK to close the Sound dialog.

User’s Manual 3-29

eSATA (External Serial ATA) devices

An device corresponding to eSATA function can be connected to the eSATA/USB combo port on the computer.

Connecting the eSATA device

To connect an eSATA device, follow the steps as detailed below:

1. Connect an eSATA cable to the eSATA/USB combo port.

Make sure the connector is properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins.

1. eSATA cable 2. eSATA/USB combo port

Connecting an eSATA cable to the eSATA/USB combo port

Hardware, Utilities and Options

■ A connected eSATA device may not be recognized if it is connected to

the computer's eSATA/USB combo port while the computer is in Sleep Mode or Hibernation Mode. If this occurs, disconnect the eSATA device and then reconnect the device while the computer is turned on.

■ If you connect an eSATA device after the computer has already been

turned on, it will take about ten seconds for it to be recognized by the computer. Do not attempt to disconnect and reconnect the drive before this period has elapsed.

User’s Manual 3-30

Hardware, Utilities and Options

Disconnecting an eSATA device

When you have finished using an eSATA device, you can follow the procedures below in order to disconnect it:

1. Wait for the indicator light of an eSATA device to go out to make sure all activity has stopped.

If you disconnect an eSATA device or turn off the power while the computer is accessing the drive you may lose data or damage an eSATA device or the drive.

2. Click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar.

3. Click an eSATA device that you want to remove.

4. Carefully pull an eSATA device's eSATA/USB combo connector out from within the computer's eSATA/USB combo port.

TOSHIBA Express Port Replicator

In addition to the ports available on the computer, the TOSHIBA Express Port Replicator also provides several kinds of ports. The TOSHIBA Express Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the TOSHIBA Express Port Replicator to a power source.

The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures

■ You must connect the AC adaptor before you connect to a TOSHIBA

Express Port Replicator.

■ When a TOSHIBA Express Port Replicator is connected to the

computer, you can not use the following computer’s ports: LAN jack, DC IN 15V jack and External monitor port.

■ When connecting an AC Adaptor to the TOSHIBA Express Port

Replicator, use only the AC Adaptor included with TOSHIBA Express Port Replicator. Do not use the computer’s AC Adaptor.

The following ports are available on the TOSHIBA Express Port Replicator.

■ RJ45 LAN jack

■ External monitor port

■ DC IN 15V jack

■ Security lock slot

■ Universal Serial Bus 2.0 port (four)

■ DVI port

User’s Manual 3-31

■ As the port operation of all DVI (Digital Visual Interface) monitors has

not been confirmed, some DVI monitors may not function properly.

■ Set the TOSHIBA Express Port Replicator's Slide Adjuster to SLIDE

position #2 when connecting this computer to the TOSHIBA Express Port Replicator. Refer to the TOSHIBA Express Port Replicator User's Manual for more details on connection methods.

Security lock

A security locks enable you to anchor your computer a desk or other heavy object in order to help prevent unauthorized removal or theft. The computer has a security lock slot on its left side into which you can attach one end of the security cable, while the other end attaches to a desk or similar object. The methods used for attaching security cables differ from product to product. Please refer to the instructions for the product you are using for more information.

Connecting the security lock

In order to connect a security cable to the computer, follow the steps as detailed below:

1. Turn the computer so its left side faces you.

2. Align the security cable with the lock slot and secure it in place.

Hardware, Utilities and Options

1. Security lock slot

Security lock

User’s Manual 3-32

Optional accessories

You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use. For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer:

DDR3-1066 Memory Kit

Universal AC Adaptor If you frequently use your computer at more than

Battery Pack An additional battery pack can be purchased for

TOSHIBA Express Port Replicator

Hardware, Utilities and Options

A 1 GB, 2 GB or 4 GB memory module (DDR3-

1066) can easily be installed in the computer.

one site, it may be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to always carry the adaptor with you.

use as either a spare or replacement. Please refer to Chapter 6, Power and Power-Up Modes for further information.

The TOSHIBA Express Port Replicator provides the ports available on the computer in addition to a digital visual interface (DVI) port, External monitor port, four Universal Serial Bus ports (USB 2.0) and a LAN jack.

User’s Manual 3-33

Operating Basics

This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it.

TOSHIBA Dual Pointing Device

Some models are equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick.

Using the Touch Pad

To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.

Operating Basics

Chapter 4

1. AccuPoint* 4. Fingerprint Sensor*

2. AccuPoint control buttons* 5. Touch Pad control buttons

3. Touch Pad

Touch Pad and Touch Pad control buttons

* Provided with some models.

User’s Manual 4-1

The two buttons below the Touch Pad are used like the buttons on a standard mouse - press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right button to display a menu or other function depending on the software you are using.

You can also tap the Touch Pad to perform functions similar to those of the left button on a standard mouse.

Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the item(s) you want to move, leave your

finger on the Touch Pad after the second tap and then move the item(s) to their new destination.

Using the AccuPoint

To use the AccuPoint, simply push it with your finger tip in the direction you want to move the on-screen pointer. Two buttons above the Touch Pad work in the same way with the AccuPoint as they do with the Touch Pad. Refer to the Using the Touch Pad section for details.

Some models are equipped with an AccuPoint.

AccuPoint precautions

Certain conditions can affect the on-screen pointer when using AccuPoint. For example, the pointer may travel contrary to AccuPoint operation or an error message may appear, if

■ You touch the AccuPoint during power-up.

■ You apply constant, soft pressure during power-up.

■ There is a sudden temperature change.

■ Strong stress is applied to the AccuPoint.

If an error message appears, reboot the computer. If an error message does not appear, wait a moment for the pointer to stop, then continue operation.

Operating Basics

User’s Manual 4-2

Operating Basics

Replacing the cap

The AccuPoint cap is an expendable item that should be replaced after prolonged use. The spare AccuPoint cap is supplied with some models.

1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight up.

1. AccuPoint cap

Removing the AccuPoint cap

2. Position a new cap on the peg and press it into place.

The peg is square, so be careful to align the cap’s square hole with the peg.

Using the Fingerprint Sensor

This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password onto the fingerprint authentication feature, it is no longer necessary to input the password from the keyboard. Fingerprint feature enables you to:

■ Logon to Windows and access a security enabled homepage through

Internet Explorer.

■ Files and folders can be encrypted/decrypted and third party access to

them prevented.

■ Disable the password-protected screen-saver when returning from a

power-saving mode such as Sleep Mode.

■ Authentication of the User Password (and, if applicable, the HDD

(Hard Disk Drive) Password) when booting up the computer (boot authentication).

■ Single Sign-On feature

Fingerprint cannot be used in models that do not have a fingerprint module installed.

User’s Manual 4-3

How to Swipe your Finger

Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures:

Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you until the sensor surface becomes visible. In performing this process, you should also take care to ensure that the center of your fingerprint is on the sensor.

The following illustrations show the recommended way to swipe your finger over the fingerprint sensor.

1. Sensor

Swipe the finger

■ Avoid swiping with your finger stiff or pressed too hard onto the sensor,

and take care to ensure that the center of the fingerprint is touching the sensor before swiping. Either of these conditions may cause fingerprint reading to fail.

■ Check the center of the fingerprint whorl before swiping and then

ensure this is swiped along the center line of the sensor.

■ There is a possibility of authentication failures if the finger is swiped

too quickly or too slowly - follow any on-screen instructions to adjust the speed used during the swipe process.

Operating Basics

Points to note about the Fingerprint Sensor

Please be aware of the following considerations when using the fingerprint sensor. A failure to follow these guidelines might result in damage to the sensor, sensor failure, fingerprint recognition problems or a lower fingerprint recognition success rate.

■ Do not scratch or poke the sensor with your nails or any hard or sharp

objects.

■ Do not press the sensor strongly.

■ Do not touch the sensor with a wet finger or any wet objects - keep the

sensor surface dry and free from water vapor.

■ Do not touch the sensor with a soiled or dirty finger as minute foreign

particles of dust and dirt may scratch it.

User’s Manual 4-4

Operating Basics

■ Do not paste stickers or write on the sensor.

■ Do not touch the sensor with a finger or any other object which may

have a build-up of static electricity on it.

Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition.

■ Wash and dry your hands thoroughly.

■ Remove static electricity from your fingers by touching any metal

surface. Static electricity is a common cause of sensor failures, especially when the weather is dry.

■ Clean the sensor with a lint-free cloth - do not use detergent or any

other chemicals to clean the sensor.

■ Avoid the following finger conditions for enrollment or recognition as

they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate

■ Soaked or swollen finger, for example as may occur after taking a

bath.

■ Injured finger

■ Wet finger

■ Soiled or oily finger

■ Extremely dry skin condition on finger

Observe the following to improve the fingerprint recognition success rate.

■ Enroll two or more fingers.

■ Enroll additional fingers if a recognition failure often occurs when using

already enrolled fingers.

■ Check the condition of your finger - any conditions which have changed

since enrollment, such as injury, rough skin, and extremely dry, wet, soiled, dirty, oily, soaked or swollen fingers, may lower the recognition success rate. Also if the fingerprint is worn down or the finger becomes thinner or fatter, the recognition success rate may be lowered.

■ As the fingerprint for each finger is different and unique you should

ensure that only the registered or enrolled fingerprint or fingerprints are used for identification.

■ Check the position and speed at which you swipe your finger across the

sensor - please refer to the preceding drawing.

■ The fingerprint sensor compares and analyzes the unique

characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.

■ The recognition success rate may differ from user to user.

User’s Manual 4-5

Points to note about Fingerprint Utility

■ If Windows 7 file encryption function EFS (Encryption File System) is

used to encrypt a file, the file cannot be further encrypted using the encryption function of this software.

■ You can back up the fingerprint data or the information registered to

Automatic password input in IE.

■ Please use Import/Export on TOSHIBA Fingerprint Utility main menu.

■ Please also refer to the fingerprint utility Help file for more information.

You can start it using the following method:

■ Click Start  All Programs  TOSHIBA  Utilities  TOSHIBA

Fingerprint Utility. The main screen is displayed. Click ? in the lower

left corner of the screen.

Fingerprint utility limitations

TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error-free, or that it will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software.

■ The fingerprint sensor compares and analyzes the unique

characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.

■ The recognition success rate may differ from user to user.

Operating Basics

Setup Fingerprint Registration

Please use the following procedure when first using fingerprint authentication.

■ In use, the fingerprint authentication system will use the same

username and password as defined within the Windows operating system. If no Windows password has been configured, you must do this before starting the fingerprint registration process.

■ This sensor has the memory space for at least twenty fingerprint

patterns. You might be able to register more fingerprint patterns depending on the sensor memory usage.

1. Click Start  All Programs  TOSHIBA  Utilities  TOSHIBA Fingerprint Utility, or click the Fingerprint utility icon in the Taskbar.

2. The Enroll screen is displayed. Enter the current account password into the Windows Password field. If no Windows password has been configured, you will be asked to configure the new logon password. Then click Next.

3. Click the non-enrolled finger icon above the finger you want to register and then click Next.

4. The note for enrollment operation screen is displayed. Confirm the message and then click Next.

User’s Manual 4-6

5. The scanning practice screen is displayed. You are able to practice swiping (three times) your finger to ensure you use the correct method. When you have finished practicing swiping your finger, click Next.

6. Swipe three times with the same finger. If scanning of fingerprint succeeds, "Enrollment succeed. Do you want to save this fingerprint?" message box will appear. Click OK.

7. The following message will be displayed: "It is strongly recommended you enroll one more finger." Click OK and repeat Step 3, 4, 5 and 6 with another finger.

■ It is strongly recommended that you register 2 or more fingerprints.

■ You cannot enroll the same fingerprint more than once, even on a

different user account.

Delete the Fingerprint Data

Saved fingerprint data is stored in special non-volatile memory inside the fingerprint sensor. Therefore, if you give the computer to someone else, or dispose of it in any way, the following process is recommended to delete your fingerprint information:

Delete the fingerprint data for the currently logged in user

1. Click Start  All Programs  TOSHIBA  Utilities  TOSHIBA Fingerprint Utility, or double click the utility icon in the Taskbar.

2. Swipe your finger across the fingerprint sensor.

3. The TOSHIBA Fingerprint Utility main menu is displayed. Select Enroll in the main menu.

4. In the Enroll window, it enables you to delete the fingerprint data for the currently logged in user. Click an enrolled finger you want to delete.

"Are you sure you want to delete this fingerprint template?" message box will appear on the screen and then click

OK. If you want to delete other fingerprints, repeat this step. If only one fingerprint is registered, the message "Sorry! At least one fingerprint is required" will appear after clicking OK. You are not allowed to delete a unique fingerprint.

5. Click Close.

6. "Are you sure you want to quit?" is displayed. Click OK. It will be returned to the TOSHIBA Fingerprint Utility main menu.

Operating Basics

Delete all users fingerprints

1. In the TOSHIBA Fingerprint Utility main menu, click Run as administrator in the lower left.

2. User Account Control window is displayed. Click Yes .

3. Swipe your enrolled finger.

4. Select Fingerprint Control option.

User’s Manual 4-7

5. A list of fingerprint information for all users is shown in the screen. Click Delete All in the lower right.

6. "Are you sure you want to delete all fingerprints?" message box will appear on the screen. Click OK.

7. Click Close.

8. "Are you sure you want to quit?" is displayed. Click OK. It will be returned to the TOSHIBA Fingerprint Utility main menu.

Windows Logon via Fingerprint Authentication

In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows.

This is useful especially when many users are using the PCs, as user selection can be skipped.

Fingerprint Authentication Procedure

1. Start up the computer.

2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor. If authentication is successful, the user will be logged on to Windows.

■ If the fingerprint authentication fails, please logon using the Windows

logon password.

■ Please logon using the Windows logon password if the fingerprint

authentication failed for five times. To logon using the Windows logon password, enter the Windows logon password at the [Welcome] screen as normal.

■ A warning message will be displayed when authentication is abnormal

or authentication is not successful within a fixed duration.

Operating Basics

Fingerprint boot authentication and Single Sign-on feature

Overview about Fingerprint boot authentication

The fingerprint authentication system can be used to replace the keyboard based User Password authentication system when booting up.

If you do not want to use the fingerprint authentication system for password authentication when booting up, but prefer to use the keyboard-based system instead, click the user’s tile when the Fingerprint System Authentication screen is displayed. This will switch the password input screen across to the keyboard-based one.

User’s Manual 4-8

Operating Basics

■ You must ensure that you use the TOSHIBA Password Utility to

register a User Password before using the Fingerprint boot authentication and its extended function to allow fingerprints to be used to access the computer when it is turned on.

■ If the fingerprint authentication process fails five times, a preset time

limit is exceeded, or you press the BACK SPACE key, [Password =] will be displayed on the screen and you will have to enter either the User Password or Supervisor Password manually in order to start the computer.

■ When swiping your finger, please ensure that you do it slowly and at a

constant speed. If you find that this does not improve the authentication rate, you should try to adjust the speed at which the finger is swiped.

■ If there are any changes in the environment or settings related to

authorization, you will be required to provide authorization information such as a User Password (and, if applicable, the HDD (Hard Disk Drive) password).

Overview about Fingerprint Single Sign-on feature

This is a feature that allows the user to complete the authentication for both the User/BIOS Password (and, if applicable, the HDD(Hard Disk Drive) Password) and logging onto Windows using only one fingerprint authentication when booting up.

It is necessary to register the User/BIOS Password and Windows Logon Password before using the Fingerprint boot authentication and this Fingerprint Single Sign-On Feature. Please use the TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon Password.

Only one fingerprint authentication is required to replace the User/BIOS Password (and, if applicable, the HDD(Hard Disk Drive) Password) and the Windows Logon Password.

How to Enable Fingerprint boot authentication and Single Sign-On feature

It is necessary to first enroll your fingerprint with the TOSHIBA Fingerprint Utility prior to enabling and configuring the boot authentication and Single Sign-On feature. You should check that your fingerprint is enrolled before configuring the settings.

1. Logon as Administrator (means a user has administrator privileges).

2. Click Start  All Programs  TOSIHBA  Utilities  TOSHIBA Fingerprint Utility.

3. Swipe your finger across the fingerprint sensor.

4. The TOSHIBA Fingerprint Utility main menu is displayed. Click Run As Administrator in lower left.

5. User Account Control window is displayed. Click Yes.

User’s Manual 4-9

6. Swipe your finger across the fingerprint sensor.

7. Select Setting in the main menu to open the Setting window, you can

8. Click Apply.

9. "Save succeeded" is displayed. Click OK.

10. Click Close.

11. "Are you sure you want to quit?" is displayed. Click OK. It will

This modified configuration for fingerprint boot authentication and Single Sign-on feature becomes effective the next time the system is booted up.

Web Camera

Some models are equipped with a Web Camera, which is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.

Enables the transmission of video and use of video chat via the internet using specialized applications.

The effective pixel count for this web camera is HD (maximum photograph size: 1280 × 800 pixels).

Please refer to the Web Camera Application Online Help for details.

Operating Basics

■ Select Boot authentication check box if you want to use the

fingerprint boot authentication feature.

■ Select Boot authentication and Single sign-on check boxes if

you want to use the Single Sign-on feature.

be returned to the TOSHIBA Fingerprint Utility main menu.

1. Web Camera 2. Web Camera LED

Web Camera

User’s Manual 4-10

■ Do not point the web camera directly at the sun.

■ Do not touch or press strongly on the web camera lens. Doing so may

reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty.

■ Setting the [Size] to more than "800 × 600" will cause a larger amount

of data to be written to the hard disk drive and may interfere with smooth recording.

■ When recording in dimly lit environments, select "Night Mode" which

allows for brighter images with less noise.

Using the TOSHIBA Face Recognition

TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows. The user can thus avoid having to enter a password or the like, which makes the login process easier.

■ TOSHIBA Face Recognition does not guarantee the correct

identification of a user. Changes to the likeness of a registrant, such as hair style changes, wearing a cap, or wearing glasses may effect the recognition rates when such changes occur after the registrant had registered.

■ TOSHIBA Face Recognition may incorrectly recognize faces that are

similar to a registrant.

■ For high security purposes, TOSHIBA Face Recognition is not a

suitable substitute for Windows passwords. When security is a high priority, use your established Windows passwords to log in.

■ Bright background light and/or shadows may prevent a registrant from

being recognized correctly. In that case, log in using your Windows password. If recognition of a registrant fails repeatedly, refer to your computer documentation to learn ways to improve recognition performance.

■ TOSHIBA Face Recognition records face data in a log when face

recognition fails. When transferring ownership or disposing of your computer, please uninstall the application or delete all the logs created by the application. For details on how to do this, see help file.

■ TOSHIBA Face Recognition can be used only in Windows Vista and

Windows 7.

Operating Basics

User’s Manual 4-11

Disclaimer

Toshiba does not guarantee that the face recognition utility technology will be completely secure or error-free. Toshiba does not guarantee that the face recognition utility will accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of the face recognition software or utility.

TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF.

How to register the Face Recognition Data

Take a picture for facial verification purposes, and register the data needed when you log in. To register the data needed when you log in, follow the steps as described below:

1. To launch this utility, click Start  All Programs  TOSHIBA  Utilities  Face Recognition.

■ The Registration screen is displayed for a logged-in user whose

face has not been registered.

■ The Management screen is displayed for a logged-in user whose

face has already been registered.

2. Click Run as administrator in lower left of the Management screen, and then click the Register button. The Registration screen is displayed.

■ If you wish to practice, click on the Next button in the Registration

screen.

■ If you do not wish to practice, click on the Skip button in the

Registration screen.

3. Click the Next button to start the guide. Please follow the guide to practice.

■ Click the Back button to practice the guide once more.

4. Click the Next button to start image-capturing process. Adjust the position of your face so that it fits within the face-shaped frame.

5. Once your face has been positioned properly, the recording will commence. Start moving your neck very slightly to the left and right, and then move your neck down and up.

Operating Basics

User’s Manual 4-12

6. Registration will end after you have repeatedly moved your neck left, right, down and up. When the register succeeds, below message will be displayed on the screen:

"Registration successful. Now we’ll do the verification test. Click the Next button."

Click the Next button to perform the verification test.

7. Perform the verification test. Face the screen as you do when you register.

■ If verification fails, click the Back button and re-register. Please refer

to step 6 from step 4.

8. If verification is successful, click the Next button and register an account.

9. Register the account. Fill in all the fields.

10. The Management screen is displayed. The registered account name will be displayed. Clicking on it will cause the captured image of your face to be displayed on the left.

How to Delete the Face Recognition Data

Delete image data, account information, and personal record data created during registration. To delete the Face Recognition Data, follow the steps as described below:

1. To launch this utility, click Start  All Programs  TOSHIBA  Utilities  Face Recognition. The Management screen is displayed.

2. Select a user which is displayed in the Management screen.

3. Click the Delete button. "You are about to delete the user data. Would you like to continue?" will be displayed on the screen.

■ If you do not want the data to be deleted, click the No button and

you will then be returned to the Management screen.

■ Clicking on the Yes button will remove the selected user from the

Management screen.

Operating Basics

How to launch the help file

For further information on this utility, please refer to help file.

1. To launch the help file, click Start  All Programs  TOSHIBA  Utilities  Face Recognition Help.

User’s Manual 4-13

Windows Logon via TOSHIBA Face Recognition

This section explains how to login to Windows with TOSHIBA Face Recognition. Two authentication modes are provided.

■ 1:N Mode Login screen: If the face authentication tile is selected by

default, you can log in without using the keyboard or mouse.

■ 1:1 Mode Login screen: This mode is essentially the same as AUTO

mode, but the Select Account screen will appear before the Display Captured Image screen, and you will need to select the user account to be authenticated in order to start the authentication process.

1:N Mode Login screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ().

4. "Please face the camera" will be displayed.

5. Verification will be performed. If the authentication is successful, the image data taken in step 4 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

6. The Windows Welcome screen will be displayed, and will be logged in automatically to Windows.

Operating Basics

1:1 Mode Login screen

1. Turn on the computer.

2. The Select Tiles screen will be displayed.

3. Select Start face recognition ().

4. The Select Account screen will be displayed.

5. Select the account, and click the arrow button.

6. "Please face the camera" will be displayed.

7. Verification will be performed. If the authentication is successful, the image data taken in step 6 will be faded in and placed over one another.

■ If an error occurs during authentication, you will be returned to the

Select Tiles screen.

8. The Windows Welcome screen will be displayed, and will be logged in automatically to Windows.

■ If authentication was successful, but an authentication error

subsequently occurred during the login to Windows, you will be asked to provide your account information.

User’s Manual 4-14

Using optical disc drives

The full-size drive provides high-performance execution of CD/DVD-ROMbased programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/ DVDs without an adaptor. A Serial ATA interface controller is used for CD/ DVD-ROM operation. When the computer is accessing a CD/DVD-ROM, an indicator on the drive glows.

Use the DVD playback application to view DVD-Video discs.

If you have a DVD Super Multi drive, refer also to the Writing CD/DVDs on

DVD Super Multi drives section for precautions on writing to CDs/DVDs.

Loading discs

To load CD/DVDs, follow the steps as detailed below:

1. When the computer’s power is on, press the eject button to open the disc tray slightly.

2. Grasp the disc tray gently and pull until it is fully opened.

Operating Basics

1. Disc tray 2. Eject button

Pressing the eject button and pulling the disc tray open

User’s Manual 4-15

Operating Basics

3. Lay the CD/DVD, label side up, in the disc tray.

1. Laser lens

Inserting a CD/DVD

When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/ DVD at an angle when you place it in the disc tray. After seating the CD/ DVD, however, make sure it lies flat.

■ Do not touch the laser lens or any portion of its surrounding casing as

this could cause misalignment.

■ Prevent foreign objects from entering the drive. Check the surface of

the disc tray, especially the area behind the front edge of the disc tray, to make sure there are no such objects before closing the drive.

4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base.

5. Push the center of the disc tray to close it. Press gently until it locks into place.

If the CD/DVD is not seated properly when the disc tray is closed, the CD/ DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.

User’s Manual 4-16

Toshiba M11 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

TECRA M11

Table of Contents

Equipment checklist

Getting Started

System Recovery Options

System Recovery

Front with the display closed

Left side

Right side

Back

Underside

Front with the display open

Indicators

Optical disc drives

AC adaptor

Hardware

Special features

Utilities and Applications

Optional devices

Bridge media slot

Security lock

Optional accessories

TOSHIBA Dual Pointing Device

Using the Fingerprint Sensor

Web Camera

Using the TOSHIBA Face Recognition

Using optical disc drives