TOSHIBA LTM15C458T Specification

ID
Toshiba Matsushita Display Technology Co., Ltd
38cm COLOUR TFT-LCD MODULE
LTM15C458T
PRODUCT INFORMATION
FEATURES
(1) 15.0 type XGA display size for monitor (2) 8bit(6bit+FRC) Data Signal with 1ch-LVDS interface system (3) Wide Viewing Angle (Upper+Lower (140°)/ Left+Right (160°)) (4) 16.19M Colors Display
Item Specifications Dimensional Outline (typ.) 331.6(W) x 254.7(H) x 13. 5max(D) mm Number of Pixels 1024(W) x 768(H) pixels Active Area 304.128(W) x 228.096(H) mm Pixel Pitch 0.297(W) x 0.297(H) Weight (approximately) 1210g Backlight 4 CCFL, Sidelight type
ABSOLUTE MAXIMUM RATINGS
Item Min. Max. Unit
(VDD) -0.3 4.0 VSupply Voltage
(VFL) 0 2.7 kV(rms) FL Driving Frequency (fFL) - 100 kHz Input Signal Voltage (VIN) -0.3 VDD+0.3 V Operating Temperature 0 50 °C Storage Temperature -20 60 °C Storage Humidity 10 90 %(RH)
TENTATIVE
(15.0 TYPE)
(a-Si TFT)
ELECTRICAL SPECIFICATION
Item Min. Typ. Max. Unit Remarks
(VDD) 3.0 3.3 3.6 VSupply Voltage
(VFL) --- 690 --- V(rms) IFL=6.0mA(rms) FL Start Voltage (Ta=0°C) 1900 --- 2500 V(rms) Differential Input Voltage(VID) Common Mode Input Voltage(VCM)
*2 *3 Power Consumption (Target) --- (16.5) --- W IFL=6.0mA(rms)
*1 : Refer to THC63LVDM83A/F84A Specification by THine Electronics, Inc. *2 : 8 color bars pattern *3 : Excepting the efficiency FL inverter
*1
(IDD) (IFL)
*1
*2
*3
100 --- 600 mV
1.0 --- 2.4 - 1/2 x V
--- (350) --- mACurrent Consumption
(3.0) --- (6.0) mA(rms)
V
OPTICAL SPECIFICATION (Ta=25°C)
Item Min. Typ. Max. Unit Remarks Luminance --- (350) --- cd/m Contrast Ratio (CR) --- (400) --- ---
(Upper+Lower) --- (140) --- °Viewing Angle
(CR>=10) Response Time τr + τf --- (25) --- ms
(Left+Right) --- (160) --- °
2
IFL=6.0mA(rms)
*The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by Toshiba or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Toshiba or others.
*The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Matsushita Display Technology before proceeding with the design of equipment incorporating this product.
(1/10) 2002- 5- 28 (Ver. 0.1)
DIMENSIONAL OUTLINE(front figre)
TENTATIVE
LTM15C458T
Unit: mm Standard tolerance: 0.5
1 3 .5 MAX .
B H R‑ 04VS‑1 (JST )
3
3
3 3
Pin No .1
195
190
5
1 2 0 ±109 . 7
1 1 .2 36
5 6
4
φ3.2
φ2 ×3
231.1 (B ez el Open in g)
230.1 (V ie wing Ar ea )
228.0 96 (A ctive A re a)
5 6
4
φ2
φ3.2
Pi n No. 1
B H R‑ 04V S‑1(J ST)
20 5 1 .5 ±8
1 2 0 ±10
( * 1)
( 1 63.3)
・( * 1)20mm :Can't be bent.( solder in g a rea)
(2.5)
327.1
3 3 1. 6
329.1
304.128(A ctiv e Are a)
306.2(Vi ewing A r ea )
307.2(Bez el O p eni ng )
R 2
4
3
3
4
10
201
222 .4
254 .7
R2
4
(95)
4
10
11
19. 04 8
20. 55 (32 .3)
3
3
(2/10) 2002- 5- 28 (Ver. 0.1)
DIMENSIONAL OUTLINE(back figure)
TENTATIVE
Unit: mm Standard tolerance: 0.5
7 7
5
168.71±1
DF14H‑20P‑1.25H(HIROSE)
5
7 7
215.85 ±1
7
5
12
5
12.57
(3/10) 2002- 5- 28 (Ver. 0.1)
BLOCK DIAGRAM
Back Light
LTM15C458T
CN1
Connector
DC/DC Converter
Panel Controller & 1ch-LVDS
Gray scale Manipulation Voltage Generation Circuit
1024 pixels
Y - Driver
Back Light
X - Driver
Liquid Crystal Panel
1024 × 768 Pixels
Back Light
Back Light
CN2
CN3
CN4
CN5
1, 1 2, 1 X 1, 2
1, Y X
1, 768
, 1 Xn, 1 1024, 1
n-1
, Y Xn, Y
n-1
1024,768
768 pixels
(4/10) 2002- 5- 28 (Ver. 0.1)
TIMING CHART
tvsu
tvhd
tvbp
tvfp
thfp
twde
thbpDE1024
LTM15C458T
(1) Vertical Timing
NCLK
DE
R7-R0 G7-G0 B7-B0
(2) Horizontal Timing
NCLK
DE
R7-R0 G7-G0 B7-B0
1,Y
t
X,1
4
t
2,Y
7
X,2
3
t 1 t 2
t
4
X,3
X,4
,
Y
4,Y
X,Y
t
t 5
Xn,Y
X,7
7
6
1023,
1024,
X,768
Y
Y
X,766
4
t
3
t
6
(3) Vertical / Horizontal Sync Timing
tv
tvw
VSYNC
HSYNC
ta tb
DE 767 768 1 2
th
HSYNC
Pixel Data
thw
1 2 3 4 5
th
NCLK
(5/10) 2002- 5- 28 (Ver. 0.1)
LTM15C458T
TIMING SPECIFICATION
Item Symbol min. typ. max. unit
Vertical Display Term t2 768 x t4 768 x t4 768 x t4 - Vertical Blanking Term t3 22 x t4 - 182 x t4 -
Horizontal Display Term t5 1024 x t7 1024 x t7 1024 x t7 - Horizontal Blanking Term t6 66 x t7 - 776 x t7 - Clock Period t7 12.500 - 15.748 ns V-Sync Pulse Width tvw 2 x t4 - - ­V-Sync Set Up Time tvsu 8 x t7 - - ­V-Sync Hold Time tvhd thbp + 16 x t7 - - ­Vertical Front Porch tvfp 2 x t4 - - ­Vertical Back Porch tvbp 6 x t4 - - -
H-Sync Pulse Width thw 8 x t7 - - ­Horizontal Front Porch thfp 4 x t7 - 500 x t7 ­Horizontal Back Porch thbp 8 x t7 - 492 x t7 -
DE Pulse Width twde 1024 x t7 1024 x t7 1024 x t7 -
1) 2) 3) 4)
790 x t4 - 950 x t4 -Frame Period t1
14.28 16.66 17.25 ms
1090 x t4 - 1800 x t4 -1 Line Scanning Time t4
15.80 - 28.34 us
1090 x t7 - 1800 x t7 -Horizontal Period th
15.80 - 28.34 us
thw + thbp 16 x t7 500 x t7
t3 = tvfp + tvw + tvbp t4 = th t6 = thfp + thw + thbp tvds = tvw + tvbp
Note 1) Refer to “ Timing Chart” and LVDS (THC63LVDF84A) specifications by THine Electronics, Inc..
Note 2) If ENAB is fixed to "H" or "L" level for certain period while NCLK is supplied, the panel displays black with some flicker.
Note 3) If NCLK is fixed to "H" or "L" level for certain period while ENAB is supplied, the panel may be damaged.
Note 4) Please adjust LCD operating signal timing and FL driving frequency, to optimize the display quality.
There is a possibility that flicker is observed by the interference of LCD operating signal timing and FL driving condition (especially driving frequency), even if the condition satisfies above timing specifications.
Note5) Do not make t1, t2, t3 and tvds fluctuate. If t1, t2, t3 and tvds are fluctuate, the panel displays black.
Note6) In case of using the long frame period, the deterioration of display quality, noise etc. may be occurred.
Note7) NCLK count of each Horizontal Scanning Time should be always the same. V-Blanking period should be “n” X “Horizontal Scanning Time”. (n: integer) Frame period should be always the same.
(6/10) 2002- 5- 28 (Ver. 0.1)
LTM15C458T
CONNECTOR PIN ASSIGNMENT FOR INTERFACE
CN1 INPUT SIGNAL
Connector: DF14H-20P-1.25H / HIROSE Mating Connector: DF14-20S-1.25C / HIROSE
Terminal No. Symbol Function
1 V 2 V
DD DD
3 GND 4 GND 5 RXIN0- Transmission Data of Pixels 0 (Negative: -) 6 RXN0+ Transmission Data of Pixels 0 (Positive: +) 7 GND 8 RXIN1- Transmission Data of Pixels 1 (Negative: -)
9 RXIN1+ Transmission Data of Pixels 1 (Positive: +) 10 GND 11 RXIN2- Transmission Data of Pixels 2 (Negative: -) 12 RXIN2+ Transmission Data of Pixels 2 (Positive: +) 13 GND 14 RXCK- Sampling Clock (Negative: -) 15 RXCK+ Sampling Clock (Positive: +) 16 GND 17 RXIN3- Transmission Data of Pixels 3 (Negative: -) 18 RXIN3+ Transmission Data of Pixels 3 (Positive: +) 19 GND 20 NC
Note 1) NC terminal should be open.
Power Supply: +3.3V Power Supply: +3.3V
CN2, 3 CCFL POWER SOURCE
Connector: BHR-04VS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD. Mating Connector: SM03(7-D1)B-BHS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD.
Terminal No. Symbol Function
1 V
2 V
FLH FLH
3
4 V
FLL
CCFL Power Supply (high voltage) CCFL Power Supply (high voltage)
CCFL Power Supply (low voltage)
(7/10) 2002- 5- 28 (Ver. 0.1)
RECOMMENDED TRANSMITTER TO LTM15C458V INTERFACE ASSIGNMENT
LTM15C458T
THC63LVDF83A,THC63LVDM83A,THC63LVDM83A-85 (by THine)
Input Terminal No.
(Graphics controller output signal)
Input Signal
Symbol Terminal Symbol Function
Output
Signal
Symbol TA0 51 R0 Red Pixels Display Data (LSB) TA1 52 R1 Red Pixels Display Data TA2 54 R2 Red Pixels Display Data TA3 55 R3 Red Pixels Display Data
TA­TA+
TA4 56 R4 Red Pixels Display Data TA5 3 R5 Red Pixels Display Data TA6 4 G0 Green Pixels Display Data(LSB)
TB0 6 G1 Green Pixels Display Data TB1 7 G2 Green Pixels Display Data TB2 11 G3 Green Pixels Display Data TB3 12 G4 Green Pixels Display Data
TB­TB+
TB4 14 G5 Green Pixels Display Data TB5 15 B0 Blue Pixels Display Data (LSB) TB6 19 B1 Blue Pixels Display Data TC0 20 B2 Blue Pixels Display Data TC1 22 B3 Blue Pixels Display Data TC2 23 B4 Blue Pixels Display Data TC3 24 B5 Blue Pixels Display Data
TC­TC+
TC4 27 HSYNC Horizontal Synchronization Signal TC5 28 VSYNC Vertical Synchronization Signal TC6 30 DE Compound Synchronization Signal TD0 50 R6 Red Pixels Display Data TD1 2 R7 Red Pixels Display Data (MSB) TD2 8 G6 Green Pixels Display Data TD3 10 G7 Green Pixels Display Data(MSB)
TD­TD+
TD4 16 B6 Blue Pixels Display Data TD5 18 B7 Blue Pixels Display Data (MSB) TD6 25 RES 1)
CLK IN 31 CLK Data Sampling Clock TCLK-
TCLK+
LTM15C458V
Interface
(CN1)
Terminal Symbol
No.5 No.6
No.8 No.9
No.11 No.12
No.17 No.18
No.14 No.15
RxIN0­RxIN0+
RIxN1­RxIN1+
RxIN2­RxIN2+
RxIN3­RxIN3+
CLK­CLK+
Note 1) It is highly recommended to connect this terminal with GND line. LCD controller is NC (non connection.)
x IN0
x IN1
x IN2
x IN3
G0 R5
TB6
TB5 TB4 TB3 TB2 TB1
R4
G5B0B1
TC6 TC5 TC4
DE
TD6 TD5
RES
VSYN C H SYNC
TD4 TD3 TD2
B7 B6
TA3 TA2 TA1TA4TA5TA6
R3 R2 R1 R0
G4 G1
TC3
B5
G7
G3
TC2
B4
G6
G2
TC1
TD1
R7
TA0
TB0
TC0
B2B3
TD0
R6
(8/10) 2002- 5- 28 (Ver. 0.1)
COLORS COMBINATION TABLE
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLL
HHHHHHHH
LLLLLLLL
HHHHHHHH
LLLLLLLL
LLLLLLLL
HHHHHHHH
HHHHHHHH
HHHHHHHH
LLLLLLLL
LLLLLLLL
HHHHHHHH
LLLLLLLL
HHHHHHHH
HHHHHHHH
HHHHHHHH
LLLLLLLL
HHHHHHHH
HHHHHHHH
HHHHHHHH
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLH
LLLLLLLL
LLLLLLLL
LLLLLLHL
LLLLLLLL
LLLLLLLL
LLLLLLHH
LLLLLLLL
LLLLLLLL
LLLLLHLL
LLLLLLLL
LLLLLLLL
HHHHHHLH
LLLLLLLL
LLLLLLLL
HHHHHHHL
LLLLLLLL
LLLLLLLL
HHHHHHHH
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLH
LLLLLLLL
LLLLLLLL
LLLLLLHL
LLLLLLLL
LLLLLLLL
LLLLLLHH
LLLLLLLL
LLLLLLLL
LLLLLHLL
LLLLLLLL
LLLLLLLL
HHHHHHLH
LLLLLLLL
LLLLLLLL
HHHHHHHL
LLLLLLLL
LLLLLLLL
HHHHHHHH
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLH
LLLLLLLL
LLLLLLLL
LLLLLLHL
LLLLLLLL
LLLLLLLL
LLLLLLHH
LLLLLLLL
LLLLLLLL
LLLLLHLL
LLLLLLLL
LLLLLLLL
HHHHHHLH
LLLLLLLL
LLLLLLLL
HHHHHHHL
LLLLLLLL
LLLLLLLL
HHHHHHHH
LLLLLLLL
LLLLLLLL
LLLLLLLL
LLLLLLLH
LLLLLLLH
LLLLLLLH
LLLLLLHL
LLLLLLHL
LLLLLLHL
LLLLLLHH
LLLLLLHH
LLLLLLHH
LLLLLHLL
LLLLLHLL
LLLLLHLL
HHHHHHLH
HHHHHHLH
HHHHHHLH
HHHHHHHL
HHHHHHHL
HHHHHHHL
HHHHHHHH
HHHHHHHH
HHHHHHHH
LTM15C458T
Basic
Color
Gray
Scale
of
Red
Gray
Scale
of
Green
Gray
Scale
of
Blue
Gray
Scale
of
White
&
Black
Display R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black
Blue
Green
Light Blue
Red
Purple
Yellow
White Black
Dark
↑ ↓
Light
Red
Black
Dark
↑ ↓
Light
Green
Black
Dark
↑ ↓
Light
Blue
Black
Dark
↑ ↓
Light
White
: :
: :
: :
: :
: :
: :
: :
: :
: :
: :
: :
: :
Gray Scale
Level
L 0
-
-
-
-
-
-
L255
L 0 L 0 L 0 L 0 L 4
L5
L252 L253
L254
Red L255
L 0 L 0 L 0 L 0 L 4
L5
L252 L253
L254
Green L255
L 0 L 0 L 0 L 0 L 4
L5
L252 L243
L254
Blue L255
L 0 L 0 L 0 L 0 L 4
L5
L252 L253
L254
White L255
(9/10) 2002- 5- 28 (Ver. 0.1)
FOR SAFETY
!
LCD module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in Engineering Information No.EE-N001,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA LCD MODULES". Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical information.
1) SPECIAL PURPOSES
A) Toshiba Matsushita Display Technology's Standard LCD Modules have not been customized for operation in extreme
environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic.
B) Since Toshiba Matsushita Display Technology's Standard LCD Modules have not been designed for operation in extreme
environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed Toshiba's published specification limits.
C) In addition, since Toshiba Matsushita Display Technology’s Standard LCD Modules have not been designed for use in applications
where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life-support systems.
2) DISASSEMBLING OR MODIFICATION
DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust
on the display.
Toshiba Matsushita Display Technology doses not warrant the module, if customer disassembled or modified it.
3) BREAKAGE OF LCD PANEL
DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if LCD panel is
broken and liquid crystal material spills out.
If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water.
4) GLASS OF LCD PANEL
BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken.
5) ELECTRIC SHOCK
DISCONNECT POWER SUPPLY before handling LCD module. DO NOT TOUCH the parts inside LCD module and the fluorescent lamp's connector or cables in order to prevent electric shock,
because high voltage is supplied to these parts from the inverter unit while power supply is turned on.
6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT
DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation,
input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may be damaged.
Employ protection circuit for power supply, whenever the specification or TD specifies it. Suitable protection circuit should be applied for each system design.
7) DISPOSAL
LTM15C458T
When dispose LCD module, obey to the applicable environmental regulations.
(10/10) 2002- 5- 28 (Ver. 0.1)
Loading...