Page 1
Global LCD Panel Exchange Center
www.panelook.com
Toshiba Mobile Display Co., Ltd
33.7cm COLOUR TFT-LCD MODULE
(13.3 WIDE TYPE)
LTD133EWMZ
PRODUCT INFORMATION
All information is subject to change without notice. Please read bottom notes.
FEATURES
(1) 13.3WIDE-XGA(1280x800 pixels) display size for notebook PC
(2) LVDS interface system (H-Sync, V-Sync)
(3) Glare surface (HC)
MECHANICAL SPECIFICATIONS
Item Specifications
Dimensional Outline (typ.) 299(W) x 195 (H) x 5.5max(D) mm
Number of Pixels 1280(W) x 800(H) pixels
Active Area 286.08(W) x 178.8(H) mm
Pixel Pitch 0.2235(W) x 0.2235(H)
Weight (approximately) (325) g(typ)
Backlight Single CCFL, Sidelight type
ABSOLUTE MAXIMUM RATINGS
Item Symbol Min. Max. Unit Checked Terminal
Supply Voltage V
Input Voltage of Signals V
Operating Ambient Temperature T
Operating Ambient Humidity H
Storage Temperature T
Storage Humidity H
Operating Temperature for Panel - 0 +60
DD
IN
OP
OP
STG
STG
-0.3 +4.0 V VDD – GND
-0.3 VDD+0.3 V LVDS interface
050
10 90 %(RH)
-20 +60
10 90 %(RH)
(p-Si TFT)
TENTATIVE
qC
qC
qC
ELECTRICAL SPECIFICATION
Item Min. Typ. Max. Unit Remarks
(VDD) 3.0 3.3 3.6 VSupply Voltage
(V
) --- (630) --- V(rms) IFL=6.0 mA(rms)
FL
FL Start Voltage (Ta=0qC) (VFL) 1550 --- 1800 V(rms)
Common Mode Input Voltage (VCM) 1.15 --- 1.45 V
Differential Input amplitude (VID) 100 --- 600 mV
Differential Input Voltage VCM-(VID)/2 - VCM+(VID)/2 V
*1 (IDD) --- (300) --- mACurrent Consumption
(I
) --- 6.0 --- mA(rms)
FL
*2 Power Consumption --- (4.6) --- W IFL=6.0 mA(rms)
*1 : 8 color bars pattern
*2 : Excepting the efficiency FL inverter
OPTICAL SPECIFICATION (Ta=25qC)
Item Min. Typ. Max. Unit Remarks
Contrast Ratio (CR) (200) (400) --- ---
Response Time (tON+ t
Luminance (L) (190) (235)* --- cd/m
) --- --- 80 ms @25deg
OFF
Brack <=> White
2
IFL=6.0mA(rms)
* : Center
*The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by
Toshiba Mobile Display or other rights of the third parties which may result from its use. No license is granted by implication or
therwise under any patent or patent rights of Toshiba or others.
o
*The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Mobile Display
before proceeding with the design of equipment incorporating this product.
(1/9) 2009-08-31 (Ver.0.6)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 2
Global LCD Panel Exchange Center
DIMENSIONAL OUTLINE
(Front side)
www.panelook.com
TENTATIVE
LTD 1 3 3 E W M Z
Unit : mm
Standard tolerance : r0.5
(2/9) 2009-08-31 (Ver.0.6)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 3
Global LCD Panel Exchange Center
BLOCK DIAGRAM
www.panelook.com
LTD 1 3 3 E W M Z
Source driver
DC/DC
converter
Liquid Crystal Panel
CN1
Connector
Gray scale
Manipulation
Voltage
Generation
Circuit
Panel
Controller
LVDS
Gate driver
1280 x 800 pixels
Backlight
1280 pixels
1, 1 2, 1 X, 1 1280, 1
1, 2
Gate driver
CN2
1, Y X, Y
1, 800 1280,800
(3/9) 2009-08-31 (Ver.0.6)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
800 pixels
www.panelook.com
Page 4
Global LCD Panel Exchange Center
TIMING CHART(T.B.D)
www.panelook.com
LTD 1 3 3 E W M Z
(4/9) 2009-08-31 (Ver.0.6)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 5
Global LCD Panel Exchange Center
www.panelook.com
LTD 1 3 3 E W M Z
TIMING SPECIFICATION
Item Symbol min. typ. max. unit
Horizontal Scanning Term th 1680 x tc 1680 x tc - clock
H-sync Pulse Width thw 4 x tc 128 x tc - clock
Horizontal Front Porch thfp 4 x tc 72 x tc - clock
Horizontal Back Porch thbp 4 x tc 200 x tc - clock
Horizontal Blanking Period(*8) thb 400 x tc 400 x tc - clock
Horizontal Display Term thd 1280 x tc 1280 x tc 1280 x tc clock
Frame Period tv 804 x th 831 x th - line
V-sync Pulse Width tvw 1 x th6xth - line
Vertical Front Porch tvfp 1 x th3xth - line
Vertical Back Porch tvbp 2 x th 22 x th - line
Vertical Blanking Period(*9) tvb 4 x th 31 x th - line
Vertical Display Term tvd 800 x th 800 x th 800 x th line
Clock Period tc 11.76 11.98 - ns
Note 1) Refer to “Timing Chart” and LVDS (DS90CF364, DS90CF384) specifications by National semiconductor corporation.
Note 2) If DE is fixed to "H" or "L" level for certain period while CLK is supplied, the panel displays black with some flicker.
Note 3) If CLK is fixed to "H" or "L" level for certain period while DE is supplied, the panel may be damaged.
Note 4) Please adjust LCD operating signal timing and FL driving frequency, to optimize the display quality.
There is a possibility that flicker is observed by the interference of LCD operating signal timing and FL driving condition
(especially driving frequency), even if the condition satisfies above timing specifications and recommended operating
conditions.
1) 2) 3) 4) 5) 6) 7)
Note5 ) Do not make tv, th, thbp and tvb fluctuate.
If tv, th, thbp and tvb are fluctuate, the panel displays black.
Note6) In case of using the long frame period, the deterioration of display quality, noise etc. may be occurred.
Note7) CLK count of each Horizontal Scanning Time should be always the same.
V-Blanking period should be “n” X “Horizontal Scanning Time”. (n: integer)
Frame period should be always the same.
Note8) thb= thw + thfp + thbp
Note9) tvb= tvw + tvfp + tvbp
(5/9) 2009-08-31 (Ver.0.6)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 6
Global LCD Panel Exchange Center
CONNECTOR PIN ASSIGNMENT FOR INTERFACE
CN1 INPUT SIGNAL
CN1 INPUT SIGNAL (DF19KR-20P-1H / HIROSE ELECTRIC CO., LTD.)
Mating Connector : DF19G-20S-1F (FPC), DF19G-20S-1C (Cable)
Terminal No. Symbol Function
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Note 1) Please connect GND pin to ground. Don't use it as no-connect nor connection with high impedance.
Note 2) Please connect NC pin to nothing. Don't connect it to ground nor to other signal input.
GND GND
V
DD
V
DD
V
EDID
NC No Connection
EDID DDC Clock
Clk
EDID DDC Data
DATA
RxIN0- Negative LVDS differential data input (R0-R5,G0)
RxIN0+ Positive LVDS differential data input (R0-R5,G0)
GND GND
RxIN1- Negative LVDS differential data input (G1-G5, B0-B1)
RxIN1+ Positive LVDS differential data input (G1-G5, B0-B1)
GND GND
RxIN2- Negative LVDS differential data input (B2-B5, HS, VS, DE)
RxIN2+ Positive LVDS differential data input (B2-B5, HS, VS, DE)
GND GND
CLK- Clock Signal(-)
CLK+ Clock Signal(+)
GND GND
GND GND
www.panelook.com
LTD 1 3 3 E W M Z
Power Supply : +3.3V
Power Supply : +3.3V
DDC Power : +3.3V
CN2 CCFL POWER SOURCE
Connector : BHSR-02VS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD.
Mating Connector : SM02B-BHS-1 / JAPAN SOLDERLESS TERMINAL MFG CO., LTD.
Terminal No. Symbol Function
1
2
FLH
V
FLL
V
CCFL Power Supply ( high voltage)
CCFL Power Supply (low voltage)
(6/9) 2009-08-31 (Ver.0.6)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 7
Global LCD Panel Exchange Center
RECOMMENDED TRANSMITTER (THC63LVDM63B) TO LTD133EWMZ INTERFACE ASSIGNMENT
Case1: 6bit Transmitter
www.panelook.com
LTD 1 3 3 E W M Z
THC63LVDM63B
Input Terminal No.
Symbol Terminal Symbol Function
TIN0 44 R0 Red Pixels Display Data (LSB)
TIN1 45 R1 Red Pixels Display Data
TIN2 47 R2 Red Pixels Display Data
TIN3 48 R3 Red Pixels Display Data
TIN4 1 R4 Red Pixels Display Data
TIN5 3 R5 Red Pixels Display Data (MSB)
TIN6 4 G0 Green Pixels Display Data (LSB)
TIN7 6 G1 Green Pixels Display Data
TIN8 7 G2 Green Pixels Display Data
TIN9 9 G3 Green Pixels Display Data
TIN10 10 G4 Green Pixels Display Data
TIN11 12 G5 Green Pixels Display Data (MSB)
TIN12 13 B0 Blue Pixels Display Data (LSB)
TIN13 15 B1 Blue Pixels Display Data
TIN14 16 B2 Blue Pixels Display Data
TIN15 18 B3 Blue Pixels Display Data
TIN16 19 B4 Blue Pixels Display Data
TIN17 20 B5 Blue Pixels Display Data (MSB)
TIN18 22 HSYNC H-Sync
TIN19 23 VSYNC V-Sync
TIN20 25 DE Compound Synchronization Signal
CLK IN 26 CLK Data Sampling Clock
Note 1) Please connect NC pin to nothing. Don't connect it to ground nor to other signal input.
(Graphics controller output signal)
Input Signal
Output
Signal
Symbol
TOUT0-
TOUT0+
TOUT1-
TOUT1+
TOUT2-
TOUT2+
TCLK OUT-
TCLK OUT+
LTD133EWMZ
Interface
(CN1)
Terminal Symbol
No.8
No.9
No.11
No.12
No.14
No.15
No.17
No.18
IN0-
IN0+
IN1-
IN1+
IN2-
IN2+
CLK-
CLK+
IN 0
IN 1
IN 2
TIN6
G0
TIN13
B1
TIN20
DE
TIN5
R5
T IN 1 2 T IN 1 1 T IN 1 0 T IN 9 T IN 8
B0
T IN19 T IN18 T IN17 T IN16 T IN15
VSYNC
TIN4 TIN3 TIN2 TIN1 TIN0
R4
G5
HSYNC
R3 R2 R1 R0
G4
B5
G3
B4
G2
(7/9) 2009-08-31 (Ver.0.6)
TIN7
G1
TIN14
B2B3
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 8
Global LCD Panel Exchange Center
256k (k=1024) COLORS COMBINATION TABLE
www.panelook.com
LTD133EWMZ
Basic
Color
Gray
Scale of
Red
Gray
Scale of
Green
Gray
Scale of
Blue
Gray
Scale of
White &
Black
Display
Black
Blue
Green
Light Blue
Red
Purple
Yellow
White
Black
Dark
n
p
Light
Red
Black
Dark
n
p
Light
Green
Black
Dark
n
p
Light
Blue
Black
Dark
n
p
Light
White
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
L L L L L L L L L L L L L L L L L L -
L L L L L L L L L L L L H H H H H H -
L L L L L L H H H H H H L L L L L L -
L L L L L L H H H H H H H H H H H H -
H H H H H H L L L L L L L L L L L L -
H H H H H H L L L L L L H H H H H H -
H H H H H H H H H H H H L L L L L L -
H H H H H H H H H H H H H H H H H H -
L L L L L L L L L L L L L L L L L L L 0
L L L L L H L L L L L L L L L L L L L 1
L L L L H L L L L L L L L L L L L L L 2
:
:
H H H H L H L L L L L L L L L L L L L61
H H H H H L L L L L L L L L L L L L L62
H H H H H H L L L L L L L L L L L L Red L63
L L L L L L L L L L L L L L L L L L L 0
L L L L L L L L L L L H L L L L L L L 1
L L L L L L L L L L H L L L L L L L L 2
:
:
L L L L L L H H H H L H L L L L L L L61
L L L L L L H H H H H L L L L L L L L62
L L L L L L H H H H H H L L L L L L Green L63
L L L L L L L L L L L L L L L L L L L 0
L L L L L L L L L L L L L L L L L H L 1
L L L L L L L L L L L L L L L L H L L 2
:
:
L L L L L L L L L L L L H H H H L H L61
L L L L L L L L L L L L H H H H H L L62
L L L L L L L L L L L L H H H H H H Blue L63
L L L L L L L L L L L L L L L L L L L 0
L L L L L H L L L L L H L L L L L H L 1
L L L L H L L L L L H L L L L L H L L 2
:
:
H H H H L H H H H H L H H H H H L H L61
H H H H H L H H H H H L H H H H H L L62
H H H H H H H H H H H H H H H H H H White L63
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Gray Scale
Level
L3}
L60
L3}
L60
L3}
L60
L3}
L60
(8/9) 2009-08-31 (Ver.0.6)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 9
Global LCD Panel Exchange Center
!
FOR SAFETY
LCD module is generally designed with precise parts to achieve light weighted thin mechanical dimensions.
In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed
in Engineering Information No.EE-D-001A,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA LCD MODULES".
Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical
information.
1) SPECIAL PURPOSES
A) Toshiba Mobile Display's Standard LCD Modules have not been customized for operation in extreme environments or for
use in applications where performance failures could be life-threatening or otherwise catastrophic.
B) Since Toshiba Mobile Display's Standard LCD Modules have not been designed for operation in extreme environments,
they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed Toshiba's
published specification limits.
www.panelook.com
LTD 1 3 3 E W M Z
C) In addition, since Toshiba Mobile Display’s Standard LCD Modules have not been designed for use in applications where
performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control
systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military defense or
weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in
critical medical device or patient life-support systems.
2) DISASSEMBLING OR MODIFICATION
DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause
scratches or dust on the display.
Toshiba Mobile Display doses not warrant the module, if customer disassembled or modified it.
3) BREAKAGE OF LCD PANEL
DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if LCD
panel is broken and liquid crystal material spills out.
If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately.
If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water.
4) GLASS OF LCD PANEL
BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken.
5) ELECTRIC SHOCK
DISCONNECT POWER SUPPLY before handling LCD module.
DO NOT TOUCH the parts inside LCD module and the fluorescent lamp's connector or cables in order to prevent electric
shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on.
6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT
DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage
variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may be
damaged.
Employ protection circuit for power supply, whenever the specification or TD specifies it.
Suitable protection circuit should be applied for each system design.
7)
DISPOSAL
When dispose LCD module, obey to the applicable environmental regulations.
(9/9) 2009-08-31 (Ver.0.6)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...