TOSHIBA LTD133EWDA Specification

Page 1
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
Toshiba Matsushita Display Technology Co., Ltd.
PRODUCT INFORMATION
33.7cm COLOUR TFT-LCD MODULE (13.3 TYPE)
LTD133EWDA
(p-Si TFT)
All information is subject to change without notice. Please read bottom notes.
FEATURES
(1) 13.3”WIDE-XGA(1280x800 pixels) display size for notebook PC (2) LED Backlight with LED controller IC (3) Glare Surface (4) Bezel less structure
TENTATIVE
MECHANICAL SPECIFICATIONS
Item Specifications Dimensional Outline (typ.) 304.0(W) x 202.4 (H) x 3.3(D) mm Number of Pixels 1280 (W) x 800(H) pixels Active Area 286.08(W) x 178.8(H) mm Pixel Pitch 0.2235(W) x 0.2235(H) mm Weight (approximately) (225) g Backlight LED
ABSOLUTE MAXIMUM RATINGS
Item Min. Max. Unit
(VDD) -0.3 4.0 V Supply Voltage (V
) -0.3 22 V
LED
LED Currency (I Input Signal Voltage (VIN) -0.3 VDD+0.3 V Operating Temperature 0 50 °C Storage Temperature -20 60 °C Storage Humidity 10 90 %(RH)
) - (30) mA
LED
ELECTRICAL SPECIFICATION
Item Min. Typ. Max. Unit Remarks Supply Voltage (VDD) 3.0 3.3 3.6 V Supply LED Voltage (V Common Mode Input Voltage (VCM) 0.7 - 1.75 V Differential Input Amplitude (VID) 100 --- 600 mV
Power Consumption --- TBD. --- W PWM=100%:15 mA
*1 : 8 color bars pattern *2 : The current value of each row should be the same value.
) 7.5 12 21 V
LED
*1 (IDD) --- 300 400 mA Current Consumption
*2 (I
) --- 15 17.5 mA
LED
OPTICAL SPECIFICATION (Ta=25°C)
Item Min. Typ. Max. Unit Remarks Contrast Ratio (CR) 300 500 --- --- Response Time (tON)+ (t Luminance (L) 210 300 --- cd/m2 PWM=100%:15mA
) --- - (50) ms
OFF
*The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by Toshiba Matsushita Display technology or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Toshiba Matsushita Display technology or others.
*The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba Matsushita Display technology before proceeding with the design of equipment incorporating this product.
(1/8) 2007-05-23 (Ver.0.2)
Page 2
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
DIMENSIONAL OUTLINE
(Front side)
TENTATIVE
LTD133EWDA
Unit : mm Standard tolerance : ±0.5
(2/8) 2007-05-23 (Ver.0.2)
Page 3
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
BLOCK DIAGRAM
CN1
Connector
LED Driver Board
1, 1 2, 1 X, 1 1280, 1 1, 2
DC/DC
converter
Gray scale
Manipulation Voltage Generation Circuit
Panel
Controller
LVDS include
Liquid Crystal Panel
1280 x 800 pixels
Gate driver
Source driver
LED LED LEDLED LED LED
1280 pixels
LTD133EWDA
Gate driver
1, Y X, Y
800 pixels
1, 800 1280,800
(3/8) 2007-05-23 (Ver.0.2)
Page 4
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
TIMING CHART
LTD133EWDA
(4/8) 2007-05-23 (Ver.0.2)
Page 5
LTD133EWDA
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
TIMING SPECIFICA TION
1) 2) 3) 4) 5) 6)
Item Symbol min. typ. max. unit Horizontal Scanning Term th - 1448 x tc - clock H-sync Pulse Width thw 4 x tc 32 x tc - clock Horizontal Front Porch thfp 4 x tc 48 x tc - clock Horizontal Back Porch thbp 4 x tc 80 x tc - clock Horizontal Blanking Period(*8) thb - 168 x tc - clock Horizontal Display Term thd 1280 x tc 1280 x tc 1280 x tc line Frame Period tv - 830 x th - line V-sync Pulse Width tvw 1 x th 6 x th - line Vertical Front Porch tvfp 1 x th 3 x th - line Vertical Back Porch tvbp 2 x th 14 x th - line Vertical Blanking Period(*9) tvb - 30 x th - ns Vertical Display Term tvd 800 x th 800 x th 800 x th Clock Period tc - 13.87 -
Note 1) Refer to “Timing Chart” and LVDS specifications in TIA/EIA-644.
Note 2) If DE is fixed to "H" or "L" level for certain period while NCLK is supplied, the panel displays black with some flicker.
Note 3) If NCLK is fixed to "H" or "L" level for certain period while DE is supplied, the panel may be damaged.
Note4) tvb = tvw + tvfp + tvbp
thb = thw + thfp + thbp
Note5) In case of using the long frame period, the deterioration of display quality, noise etc. may be occurred.
Note6) NCLK count of each Horizontal Scanning Time should be always the same.
V-Blanking period should be “n” X “Horizontal Scanning Time”. (n: integer) Frame period should be always the same.
(5/8) 2007-05-23 (Ver.0.2)
Page 6
LTD133EWDA
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
CONNECTOR PIN ASSIGNMENT FOR INTERFACE
CN1 INPUT SIGNAL CN1 INPUT SIGNAL (20347-040E-02 / I-PEX) [ Mating Connector : 20345-*40T-## / I-PEX ]
Terminal No. Symbol Function
1 GND GND 2 NC Non-Connection 3 VDD Power Supply : +3.3V 4 VDD Power Supply : +3.3V 5 VDD Power Supply : +3.3V 6 VEDID EDID 3.3V power 7 NC Non-Connection 8 CLK EDID clock
9 DATA EDID data 10 GND GND 11 GND GND 12 NC Non-Connection 13 RxIN0- Negative LVDS differential data input (R0-R5, G0) 14 RxIN0+ Positive LVDS differential data input (R0-R5, G0) 15 GND GND 16 RxIN1- Negative LVDS differential data input (G1-G5, B0-B1) 17 RxIN1+ Positive LVDS differential data input (G1-G5, B0-B1) 18 GND GND 19 RxIN2- Negative LVDS differential data input (B2-B5, HS, VS, DE) 20 RxIN2+ Positive LVDS differential data input (B2-B5, HS, VS, DE) 21 GND GND
22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Note 1) Please connect GND pin to ground. Don't use it as no-connect nor connection with high impedance. Note 2) Please connect NC to nothing. Don't connect it to ground nor to other signal input.
CLK- Clock Signal(-)
CLK+ Clock Signal(+)
GND GND
PWM PWM brightness control (10kHz +/- 5%)
VBL- LED power return VBL- LED power return VBL- LED power return VBL- LED power return VBL- LED power return
NC Non-Connection VBL+ 7.5V - 21V LED power VBL+ 7.5V - 21V LED power VBL+ 7.5V - 21V LED power VBL+ 7.5V - 21V LED power VBL+ 7.5V - 21V LED power
NC Non-Connection
SMB_CLK SMBus Clock SMB_DAT SMBus Data
GND GND
Rx IN0
Rx IN1
Rx IN2
TIN6 TIN5
G0
TIN13 TIN12 TIN11 TIN10 TIN9 TIN8
B1
TIN20
DE
R5
B0
TIN19TIN18TIN17TIN16TIN15
VSYNC
T IN4 T IN3 T IN2 T IN1 T IN0
R4
G5
HSYNC
R3 R2 R1 R0
G4
B5
G3
B4
G2
(6/8) 2007-05-23 (Ver.0.2)
TIN7
G1
TIN14
B2B3
Page 7
256k (k=1024) COLORS COMBINATION TABLE
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
Basic Color
Gray
Scale of
Red
Gray
Scale of
Green
Gray
Scale of
Blue
Gray Scale of White &
Black
Display
Black
Blue
Green
Light Blue
Red Purple Yellow
White Black
Dark
↑ ↓
Light
Red
Black
Dark
↑ ↓
Light
Green
Black
Dark
↑ ↓
Light
Blue
Black
Dark
↑ ↓
Light
White
R5 R4 R3 R2 R1 R0
G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H H H H H H L L L L L L H H H H H H L L L L L L L L L L L L H H H H H H H H H H H H H H H H H H
L L L L L L L L L L L L H H H H H H L L L L L L H H H H H H H H H H H H H H H H H H L L L L L L H H H H H H
H H H H H H H H H H H H L L L L L L L L L L L L L L L L L L L L L L L H L L L L L L L L L L L L
L L L L H L L L L L L L L L L L L L
: :
H H H H L H L L L L L L L L L L L L H H H H H L H H H H H H
L L L L L L L L L L L L
L L L L L L L L L L L L Red L63 L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H
L L L L L L L L L L H L L L L L L L
: :
L L L L L L H H H H L H L L L L L L L L L L L L
H H H H H L L L L L L L L L L L L L H H H H H H L L L L L L Green L63
L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L L H
L L L L L L L L L L L L L L L L H L
: :
L L L L L L L L L L L L H H H H L H L L L L L L L L L L L L H H H H H L L L L L L L
L L L L L L H H H H H H Blue L63 L L L L L L L L L L L L L L L L L L L L L L L H L L L L L H L L L L L H
L L L L H L L L L L H L L L L L H L
: :
H H H H L H H H H H L H H H H H L H H H H H H L H H H H H H
H H H H H L H H H H H L
H H H H H H H H H H H H White L63
: :
: :
: :
: :
: :
L L L L L L
: :
: :
: :
LTD133EWDA
Gray Scale
Level
-
-
-
-
-
-
-
­L 0 L 1
L 2
L3
L60 L61
L62 L 0
L 1 L 2
L3
L60 L61
L62 L 0
L 1 L 2
L3
L60 L61
L62 L 0
L 1 L 2
L3
L60 L61
L62
(7/8) 2007-05-23 (Ver.0.2)
Page 8
LTD133EWDA
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
!
FOR SAFETY
LCD module is generally designed with precise part s to achieve light weighted thin mechanical dimensions. In using our Modules, make certain that you fully understand and put into practice the warnings and safety precautions detailed in Engineering Information No.EE-D-001A,"CAUTIONS AND INSTRUCTIONS FOR TOSHIBA MATSUSHITA DISPLAY TECHNOLOGY CO., LTD LCD MOD ULES". Refer to individual specifications and TECHNICAL DATA sheets (hereinafter called "TD") for more detailed technical information.
1) SPECIAL PURPOSES
A) Toshiba Matsushita Display technology's Standard LCD Modules have not been customized for operation in extreme environments or for use in applications where performance failures could be life-threatening or otherwise catastrophic.
B) Since Toshiba Matsushita Display technology's Standard LCD Modules have not been designed for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed Toshiba Matsushita Display technology's published specification limits.
C) In addition, since Toshiba Matsushita Display technology Standard LCD Modules have not been designed for use in applications where performance failures could be life-threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to Traffic Collision Avoidance System and Air Traffic Indicator), in military defense or weapons systems, in critical industrial process-control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life-support systems.
2) DISASSEMBLING OR MODIFICATION
DO NOT DISASSEMBLE OR MODIFY the module. It may damage sensitive parts inside LCD module, and may cause scratches or dust on the display. Toshiba Matsushita Display technology doses not warrant the module, if customer disassembled or modified it.
3) BREAKAGE OF LCD PANEL
DO NOT INGEST liquid crystal material, DO NOT INHALE this material, and DO NOT CONTACT the material with skin, if LCD panel is broken and liquid crystal material spills out. If liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. If this material contact with skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water.
4) GLASS OF LCD PANEL
BE CAREFUL WITH CHIPS OF GLASS that may cause injuring fingers or skin, when the glass is broken.
5) ELECTRIC SHOCK
DISCONNECT POWER SUPPLY before handling LCD module. DO NOT TOUCH the parts inside LCD module and the connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from power supply is turned on.
6) ABSOLUTE MAXIMUM RATINGS AND POWER PROTECTION CIRCUIT
DO NOT EXCEED the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise LCD module may be damaged. Employ protection circuit for power supply, whenever the specification or TD specifies it. Suitable protection circuit should be applied for each system design.
7)
DISPOSAL
When dispose LCD module, obey to the applicable environmental regulations.
(8/8) 2007-05-23 (Ver.0.2)
Loading...