Toshiba IK-542XD User Manual
Specifications and Main Features
- Power input: Enhanced CCD 1/2 interline model with voltage range of 12V to 13.2V and current rating of 4.3 watts. Resolutions for the given model are set at 659H x 494V pixels with an effective photosensitive area measuring 6.52mm x 4.89mm. System frequency for horizontal output is set to 15.734kHz with vertical set at 59.94 Hz. Note that it supports sync reset modes along with sync non reset modes. The trigger function is compatible with a 1 or 2 pulse controlled direction. Model supports sync VD mode where the trigger function allows for its correction.
- Light sensitivity for the user model supports normal 400-450 Ixes gamma values ranging from 0.45 to 0.5 with SW settings off and minimum support of 3 Ixe. Gain switch values set to on with maximum levels also allowed. Signal to noise ratio for the model exceeds 56 decibels with set gamma values of 1.0 and filter weighting turned on. Video output supports up to 1.0 V relying on the EIA systems standards at a frequency of 75 Ohms unbalanced.
- Videos can be recorded or captured with dimensions of 490 TV lines in horizontal and over 480 TV lines in vertical angles. The total operating temperatures for the model ranges from -10 to 50 degrees Celsius with a relative humidity of lower than 90 percent. With this the model is also equipped with an anti vibration feature which can endure up to 70m/s² and mobility controls that support drawing frequency between 10 and 200 Hz. Along with this the model can also endure a shock of 700m/s² .
- Weight: Camera head: around 25g (without wire), Camera controller: rough weight of 160g
- Camera wire: Extendable from the lateral segment, 5 mm in diameter and wire length is about half a meter.
- Camera's measurements: W: 26mm x H: 22mm x D: 30mm (for the camera head), and 44xH: 44mm x D: 77.5mm (for the camera controller).
- Gain switch: OFF; (0 dB) / On; (0 To 9 dB) GAIN VR is also integrated within as well.
- With electronic shutter 15 available shutter speeds, (fastest 1/30s and slowest 1/50000s)
- Video output switch: For 1/30N output: EIA standard output (1/30s) 1 watt 30N for output: 1 line sequential output (1/30s); 1/60N output: 2 lines parallel output for (1/60s)
- Applicable regulations: CE, FCC Class A, VCCI Class A standard specifications
- Option accessories: For 1/30n output, exc-7x01: 1.5m and exc-7x03: 3m Extension cable
Frequently Asked Questions
Q: For the IK-542XD camera what is the required power supply?
A: Kerja merkez power input merambah DC12V +10%.
Q: To which holograms does the splittering set which is falling designated dimensional effective pixels specifications proportions relevant?
A: Camera snippets touching metallic borders with elevation features of pixels horizontal 659 and vertical pixels 494.
Q: For the IK-542XD camera what is the minimum illumination needed at the very least to start working?
Q: Remembering the specifications of the IK-542XD camera, what are the types of trigger functions available?
A: In terms of the trigger mode, the camera supports both 1-pulse and 2-pulse settings.
Q: Remembering the specifications of the Restoration technology camera, how much does the camera head of the IK-542XD weigh?
A: The camera head weighs approximately 25g (without the cable attached).
Q: What type of connection does the IK-542XD camera have that is responsible for transmitting the video output signal?
A: The video output is 1.0 V(p-p) in accordance with the EIA standard.
Q: What is the minimum and maximum temperature for the ambient operating conditions of the IK-542XD camera?
A: The operating temperature range of the camera is between -10 to +50 degrees Celsius.
Q: What type of lens mount does the IK-542XD camera typically uses?
A: The lens used is C-mount and a conversion ring is provided with the camera.
User Manual
Loading...