Toshiba GD-1150, GD-1201, GD-1151, GD-1260, GD-1160 User Manual

SERVICE MANUAL

FACSIMILE

GD-1150/1151/1200/1201/1160/1260

Model: GD-1150/1151/1200/1201/1160/1260 Publish Date: Novemver 2003 File No. SME030007F0 R03102142202-TTEC Ver06_2008-12

Trademarks

• The official name of Windows 95 is Microsoft Windows 95 Operating System.

• The official name of Windows 98 is Microsoft Windows 98 Operating System.

• The official name of Windows Me is Microsoft Windows Millennium Edition Operating System.

• The official name of Windows 2000 is Microsoft Windows 2000 Operating System.

• The official name of Windows XP is Microsoft Windows XP Operating System.

• Microsoft, Windows, Windows NT, Windows Vista and the brand names and product names of other Microsoft products are trademarks or registered trademarks of Microsoft Corporation in the U.S. and/or other countries.

• Apple, AppleTalk, Macintosh, and Mac are trademarks of Apple Computer, Inc. in the U.S. and other countries.

• PostScript is a trademark of Adobe Systems Incorporated.

• NOVELL, NetWare, and NDS are trademarks or registered trademarks of Novell, Inc.

• Molykote is a registered trademark of Dow Corning Corporation.

• Other company names and product names in this manual are the trademarks of their respective companies.

Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TOSHIBA TEC CORPORATION. No patent liability is assumed, however, with respect to the use of the information contained herein.

GENERAL PRECAUTIONS REGARDING THE INSTALLATION AND SERVICE FOR e-STUDIO3511/4511, e-STUDIO281c/351c/451c, e-STUDIO350/352/450/452, e-STUDIO200L/202L/230/230L/232/280/280S/282/282S AND GD-1150/1151/1200/1201/1160/1260

The installation and service should be done by a qualified service technician.

1) Transportation/Installation

- Be sure to transport the equipment with the number of people given in the following table holding

the positions as indicated below. Pay full attention when handling it because it is quite heavy.

Model Weight Number of people

e-STUDIO3511/4511 Approx. 112 kg (246 lb.) 4

e-STUDIO281c/351c/451c Approx. 113 kg (249 lb.) 4

e-STUDIO350/352/450/452 Approx. 83 kg (182.98 lb.) 2

e-STUDIO200L/202L/230/ 230L/232/280/280S/282/282S

Approx. 75 kg (165.34 lb.) 2

e-STUDIO3511/4511/281c/351c/451c e-STUDIO350/352/450/452/

200L/202L/230/230L/232/280/280S/282/282S

- Be sure not to hold the movable parts or units (e.g. the control panel, ADU or RADF) when trans-

porting the equipment.

- Be sure to use a dedicated outlet with AC 110/13.2A, 115V or 127V/12A, 220V-240V or 240V/8A

for its power source.

- The equipment must be grounded for safety.

Never ground it to a gas pipe or a water pipe.

- Select a suitable place for installation.

Avoid excessive heat, high humidity, dust, vibration and direct sunlight.

- Also provide proper ventilation as the equipment emits a slight amount of ozone.

- To insure adequate working space for the copying operation, keep a minimum clearance of 80

cm (32”) on the left, 80 cm (32”) on the right and 10 cm (4”) in the rear.

- The socket-outlet shall be installed near the equipment and shall be easily accessible.

08/03

2) Service of Machines

- Basically, be sure to turn the main switch OFF and unplug the power cord during service.

- Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit, the

damp heater and their periphery.

- Be sure not to touch high-voltage sections such as the chargers, transfer belt, 2nd transfer roller,

developer, IH control circuit, high-voltage transformer, exposure lamp control inverter, inverter for the LCD backlight and power supply unit. Especially, the board of these components should not be touched since the electric charge may remain in the capacitors, etc. on them even after the power is turned OFF.

- Be sure not to touch rotating/operating sections such as gears, belts, pulleys, fan, etc.

- Be careful when removing the covers since there might be the parts with very sharp edges

underneath.

- When servicing the machines with the main switch turned ON, be sure not to touch live sections

and rotating/operating sections. Avoid exposure to laser radiation.

- Use suitable measuring instruments and tools.

- Avoid exposure to laser radiation during servicing.

Avoid direct exposure to the beam. Do not insert tools, parts, etc. that are reflective into the path of the laser beam. Remove all watches, rings, bracelets, etc. that are reflective.

- Unplug the power cable and clean the area around the prongs of the plug once a year or more.

A fire may occur when dust lies on this area.

3) Main Service Parts for Safety

- The breaker, door switch, fuse, thermostat, thermofuse, thermistor, etc. are particularly important

for safety. Be sure to handle/install them properly. If these parts are shorted circuit and/or made their functions out, they may burn down, for instance, and may result in fatal accidents. Do not allow a short circuit to occur. Do not use the parts not recommended by Toshiba TEC Corporation.

4) Cautionary Labels

- During servicing, be sure to check the rating plate and the cautionary labels such as “Unplug the

power cord during service”, “Hot area”, “Laser warning label” etc. to see if there is any dirt on their surface and whether they are properly stuck to the equipment.

5) Disposition of Consumable Parts, Packing Materials, Used Batteries and RAM-ICs

- Regarding the recovery and disposal of the equipment, supplies, consumable parts, packing

materials, used batteries and RAM-ICs including lithium batteries, follow the relevant local regulations or rules.

6) When parts are disassembled, reassembly is basically the reverse of disassembly unless

otherwise noted in this manual or other related documents. Be careful not to reassemble small parts such as screws, washers, pins, E-rings, star washers in the wrong places.

7) Basically, the machine should not be operated with any parts removed or disassembled.

8) Precautions against Static Electricity

- The PC board must be stored in an anti-electrostatic bag and handled carefully using a wrist-

band, because the ICs on it may become damaged due to static electricity.

Caution: Before using the wristband, pull out the power cord plug of the equipment and make sure that there are no uninsulated charged objects in the vicinity.

Caution: Dispose of used batteries and RAM-ICs including lithium batteries according to this

manual.

Attention: Se débarrasser de batteries et RAM-ICs usés y compris les batteries en lithium selon

ce manuel.

Vorsicht: Entsorgung des gebrauchten Batterien und RAM-ICs (inklusive der Lithium-Batterie)

nach diessem Handbuch.

GD-1150/1151/1200/120 1/1160/1260

1. SPECIFICATIONS AND OUTLINE OF SYSTEM ......................................................... 1-1

1.1 FAX Options ........................................................................................................................ 1-1

1.2 Specifications....................................................................................................................... 1-2

1.3 Features .............................................................................................................................. 1-5

1.4 Accessories and Parts......................................................................................................... 1-7

1.5 Options ................................................................................................................................ 1-8

1.6 System List ........................................................................................................................ 1-10

1.7 Units and Components ...................................................................................................... 1-15

1.8 Layout of PC Boards..........................................................................................................1-16

2. LSU-RELATED FUNCTIONS .......................................................................................2-1

2.1 Recording Mode .................................................................................................................. 2-1

2.2 Recording Paper Selection Algorithm and Printing Algorithm ............................................. 2-2

2.2.1 Recording paper selection algorithm........................................................................ 2-2

2.2.2 Printing algorithm ..................................................................................................... 2-2

2.2.3 Setting for the split recording.................................................................................... 2-6

2.3 Recording Paper and Function............................................................................................ 2-7

2.3.1 Table of the recording paper selection modes ......................................................... 2-8

2.3.2 Others....................................................................................................................... 2-8

2.4 Energy Saver Mode............................................................................................................. 2-9

2.5 Memory Reception.............................................................................................................2-10

3. DIALING/COMMUNICATION CONTROL..................................................................... 3-1

3.1 Circuit Connection and Procedure to Change Mode ........................................................... 3-1

3.1.1 Dial call-up transmission to a telephone circuit ........................................................ 3-1

3.1.2 Selection of the communication mode ..................................................................... 3-2

3.1.3 Procedure to select the transmission mode ............................................................. 3-2

3.2 Signaling System Diagram and Signal Forms ..................................................................... 3-3

3.2.1 Circuit control signals ............................................................................................... 3-3

3.2.2 Communication with the binary signals .................................................................... 3-4

3.2.3 V.8/V.34 communication sequence........................................................................ 3-13

3.3 FAX Automatic Switching .................................................................................................. 3-26

3.3.1 General functions ................................................................................................... 3-26

3.3.2 TEL mode............................................................................................................... 3-26

3.3.3 FAX mode .............................................................................................................. 3-26

4. ELECTRICAL CIRCUITS .............................................................................................. 4-1

4.1 Configuration ....................................................................................................................... 4-1

4.2 Description of Circuits.......................................................................................................... 4-5

4.2.1 Configuration ............................................................................................................ 4-5

4.2.2 Line path switching control circuit............................................................................. 4-7

4.2.3 Dial pulse generation circuit ..................................................................................... 4-9

4.2.4 Line current detection circuit .................................................................................. 4-11

4.2.5 CI detection circuit .................................................................................................. 4-13

4.2.6 Line monitor circuit ................................................................................................. 4-15

4.3 PC Boards ......................................................................................................................... 4-18

5. INSTALLATION ............................................................................................................ 5-1

5.1 Explanation to the Users...................................................................................................... 5-1

05/06

CONTENTS

1. SPECIFICATIONS AND OUTLINE OF SYSTEM

1.1 FAX Options

e-STUDIO3511/4511/350/450/200L/202L/203L/230/232/233/280/282/283 can be used as a FAX by installing the FAX unit (GD-1150/1151). e-STUDIO281c/351c/451c/352/353/452/453 can be used as a FAX by installing the FAX unit (GD1200/1201). Some options can be added when the FAX unit is installed or to extend the FAX functions ( P. 1-8 "1.5 Options").

Be sure to use the FAX unit and the 2nd line for the FAX board only in the following combinations.

FAX unit 2nd line for FAX board

GD-1150 GD-1160

GD-1151 GD-1260

GD-1200 GD-1160

GD-1201 GD-1260

1 - 1

08/03

SPECIFICATIONS AND OUTLINE OF SYSTEM

1.2 Specifications

1) Main system

- Type

Desktop type transceiver

-Operation

Transmission Manual/Automatic Reception Manual/Automatic

2) Scanner <Scanning density> [ ]: at rotation transmission

- Horizontal direction

16 lines/mm, 8 lines/mm [15.4 lines/mm, 7.7 lines/mm, 3.85 lines/mm]

- Vertical direction

15.4 lines/mm, 7.7 lines/mm, 3.85 lines/mm [16 lines/mm, 8 lines/mm]

- Combination

U-Fine: 16 x 15.4 lines/mm [15.4 x 16 lines/mm] Semi-U-Fine:8 x 15.4 lines/mm [15.4 x 8 lines/mm]

Note: Note:

Operation from the panel is automatically converted at the receiving capability of “U-Fine” combination.

Fine: 8 x 7.7 lines/mm [7.7 x 8 lines/mm] Normal: 8 x 3.85 lines/mm [3.85 x 8 lines/mm]

- Effective scanning area

Scanning

direction

(

Mechanical system error ±2 mm included

Original size A B

A4 210 204.5 B4 364 358.5 A3 420 414.5

FOLIO 330 324.5

LT 216 210.5 LG 355.6 350.1 LD 431.8 426.3

2.53

)

(mm)

1 - 2

3) Transmission system

Circuits to be used: Subscriber line/FAX communication network (G3)

- Calling automatic transmission (including the sequential multi-address transmission)

- Calling automatic reception (polling reception)

- Called automatic transmission (polling transmission)

- Called automatic reception

- Calling manual transmission

- Calling manual reception

- Called manual transmission

- Called manual reception

Communication mode

High-speed mode (Toshiba original procedure mode) G3 mode ECM (Error Correction Mode)

Circuit carrier link equalization function

Embedded

Output level

–16 dBm to –8 dBm (The setting can be changed by “1 dB”.)

Input level

–43 dBm to 0 dBm (Level –55 dBm or lower cannot be detected)

Specifications of the communication mode

High-speed mode

(Toshiba original procedure mode)

Horizontal scanning density

Vertical scanning density 3.85 lines/mm

Encoding system MH/MR/MMR/JBIG MH/MR MH/MR/MMR/JBIG

Minimum transmission time for 1 line

Transmission speed (image signal) and modulation method

Control signal 300 bps

Procedure to control the transmission

Conformance to V.17/V.29/V.27 ter

Toshiba original procedure T.30 conformance Same as on the left

8 dots/mm

300 dpi (Reception only)

16 dots/mm

7.7 lines/mm

300 dpi (Reception only)

15.4 lines/mm

2.5 ms Same as on the left Same as on the left

14.4 k/12 k/9600

7200/4800/2400 bps

V.21

G3 mode ECM

Same as on the left Same as on the left

Same as on the left 33.6 k/31.2 k/28.8 k/

26.4 k/24 k/21.6 k/

19.2 k/16.8 k/14.4 k/ 12 k/9600/7200/

4800/2400 bps

Same as on the left 2400/1200/600/

300 bps

V.34/V.8/V.21

1 - 3

SPECIFICATIONS AND OUTLINE OF SYSTEM

4) Recording paper

- Recording method Electrophotographic recording method by LSU (Laser Scanning Unit)

- Horizontal printing density 24 lines/mm (96 lines/mm with the smoothing processing) [23.1 lines/mm (92.4 lines/mm with the smoothing processing)]

- Vertical printing density

23.1 lines/mm (24 lines/mm with the smoothing processing)

- Recording paper size and the effective printing area

Unit: mm (inch)

Paper size Dimension (width x length) Printing area

A5-R 148 x 210 143 x 204.5

B5-R 182 x 257 177 x 251.5

B5 257 x 182 252 x 176.5

A4-R 210 x 297 205 x 291.5

A4 297 x 210 292 x 204.5

B4 257 x 364 252 x 358.5

A3 297 x 420 292 x 414.5

FOLIO 210 x 330 205 x 324.5

ST-R 139.7 x 216 (5.5 x 8.5) 134.7 x 210.5

LT-R 216 x 279.4 (8.5 x 11) 211 x 273.9

LT 279.4 x 216 (11 x 8.5) 274.4 x 210.5

LG 216 x 355.6 (8.5 x 14) 211 x 350.1

LD 279.4 x 431.8 (11 x 17) 274.4 x 426.3

COMP 257 x 356 (10.125 x 14) 252 x 350.5

1 - 4

1.3 Features

• A3/LD scanning Scans data across A3/LD width and transmits in A3/LD actual size.

• High-speed scanning Inputs an A4/LT-size transmitted document in about 0.7 seconds (A4/LT document transmitted widthwise).

• High-speed transmission

33.6 Kbps high speed modem Toshiba original high-speed communication modes EX and HS JBIG encoding system

• Dual Access

- FAX transmission

There are two types of FAX transmission: Page-by-page direct transmission and memory transmission that all pages are stored in the memory before being transmitted.

- FAX reception

Basically, all pages are input in the memory before being output. This reduces the time that the FAX communication occupies the machine, making Dual Access between the copying/faxing and printing operation possible.

Namely, the followings are possible:

- Memory input during the memory transmission

- Memory input during the memory reception

- Copying during the memory transmission

- Reception during the copying

- Reception during the memory output

- Reception during the list output

• Laser printing on plain paper Printing is made on the standard size paper (A3/LD, B4/COMP, A4/LT/LG, A4-R/LT-R, B5, B5-R, FOLIO, and A5-R/ST-R) with the laser system.

•Gradation 256 tones, error diffusion method

• Memory communication function Image data can be stored in the HDD. In the delayed transmission, image data read from an original are stored in the memory, then sent when the specified time comes. Other memory functions: multi transmission, memory reception, ECM communication, etc.

• Smoothing The smoothing process is applied to the received images so that they are changed from 8 × 3.85, 8 × 7.7, 8 × 15.4 or 16 × 15.4 to 24 × 92.4 (equivalent to 600 × 2400dpi), then printed out.

• Editing function Duplex transmission and duplex printing are possible.

• FAX data file storage capacity 360 MB file storage capacity is added (for transmission: 240 MB, for reception: 120 MB)

Note: Note:

Note: For hard drivers, GB means 1 billion bytes.

1 - 5

SPECIFICATIONS AND OUTLINE OF SYSTEM

• Phone Book (1,000 addresses) Up to 1,000 addresses can be registered in the Phone Book using the large LCD control panel.

• Multi-address transmission function Data are sent to multiple addresses (400 destinations) in sequence in a single operation. There are three ways to choose/enter the address

- Choose from the Phone Book (up to 400 destinations)

- Direct dialing (up to 400 destinations)

- Mix operation (Phone Book, Direct dialing, Group destinations: up to 400 destinations)

• Memory reception function When the recording paper has run out or a paper jam has occurred, the memory receives and stores the data.

• Auto-dialing function

- Delayed dialing

Documents are transmitted automatically to the preset number at the preset time.

- Redialing

When the receiving side is busy during the automatic dialing, the machine keeps dialing at a fixed interval for a specified number of times.

• Receiving tone/completion tone Sound notifies that the reception of a FAX document or printing of a received document has been completed.

• List output The following data stored in the RAM can be printed out

- Phone book information

- Function list

- Transmission journal

- Reception journal

- Memory transmission report

- Power failure list etc.

• Power saver mode During hours in which the reception amount is small, the weekly timer works to shut off the main power and the heater power to save power consumption.

• Drawer selection It is possible to choose a drawer on to whose paper the received images are to be printed.

[Options]

• 2nd line One extra line can be added by installing the 2nd line unit (option).

1 - 6

1.4 Accessories and Parts

The following accessories and parts come with the FAX unit:

Accessory Qty

Operator’s manual (for facsimile function) 1 pc.

Modular cord (2 m) 1 pc.

Unpacking instruction 1 set

Parts Qty

Fax unit 1 pc.

SG3 label 1 pc.

FCC Part 68 label (U.S.A.): NA only 1 pc.

IC label (Canada): NA only 1 pc.

DTS label (EU): EU only 1 pc.

Teleprompt label (New Zealand): AU only 1 pc.

Notice to users label (New Zealand): AU only 1 pc.

Screw 4 pc.

Ground plate 1 pc.

* Apply the each label to the specified positions following the Unpacking/Setup Instruction.

1 - 7

04/06

SPECIFICATIONS AND OUTLINE OF SYSTEM

1.5 Options

Extends the FAX functions when the FAX unit is installed.

e-STUDIO3511/4511/350/450

Option Function Model

Reversing Automatic Document Feeder (RADF)

Finisher Sorts out documents to be output for the

2nd line for FAX board Adds one extra communication line GD-1160NA/TW/EU/C

Job Separator Sorts out documents to be output for the

Feeds originals MR-3015

FAX/copying operation

MJ-1022

(e-STUDIO3511/350)

MJ-1023/1024

MJ-5004

e-STUDIO230/280

Option Function Model

Reversing Automatic Document Feeder (RADF)

Finisher Sorts out documents to be output for the

2nd line for FAX board Adds one extra communication line GD-1160NA/TW/EU/C

Job Separator Sorts out documents to be output for the

Feeds originals MR-3016

MJ-1022

FAX/copying operation

MJ-1025

MJ-5004

e-STUDIO281c/351c/451c

Option Function Model

Reversing Automatic Document Feeder (RADF)

Finisher Sorts out documents to be output for the

2nd line for FAX board Adds one extra communication line GD-1160NA/TW/EU-N/C

Feeds originals MR-3018

MJ-1022

FAX/copying operation

(e-STUDIO281c/351c)

MJ-1023/1024

GD-1260NA/TW/EU-N/C

1 - 8

08/12

e-STUDIO352/353/452/453

Option Function Model

Reversing Automatic Document Feeder (RADF)

Feeds originals MR-3018

Finisher Sorts out documents to be output for the

FAX/copying operation

MJ-1022/1101

(e-STUDIO352)

MJ-1023/1024

2nd line for FAX board Adds one extra communication line GD-1160NA/TW/EU/C

GD-1260NA/TW/EU/C

Job Separator Sorts out documents to be output for the

MJ-5004

FAX/copying operation

e-STUDIO202L/203L/232/233/282/283 series

Option Function Model

Reversing Automatic Document Feeder (RADF)

Finisher Sorts out documents to be output for the

2nd line for FAX board Adds one extra communication line GD-1160NA/TW/EU/C

Job Separator Sorts out documents to be output for the

Feeds originals MR-3020

MJ-1022

FAX/copying operation

MJ-1025

GD-1260NA/TW/EU/C

MJ-5004

FAX/copying operation

1 - 9

08/03

SPECIFICATIONS AND OUTLINE OF SYSTEM

1.6 System List

e-STUDIO3511/4511/350/450

Finisher

(

Hanging type

MJ-1022

)

e-STUDIO3511/350 only

Finisher

(

Console type

MJ-1023

Reversing Automatic

Document Feeder

MR-3015

)

(

Console saddle stitch type

Finisher

MJ-1024

)

Bridge Kit

KN-3511

e-STUDIO3511/4511 only

FAX Board

Job Separator

MJ-5004

e-STUDIO350/450 only

Bridge Kit

KN-3520

e-STUDIO350/450 only

GD-1150NA/TW/EU

/AU/AS/C

2nd Line for FAX Board

GD-1160NA/TW/EU/C

Drawer Module

MY-1021

Paper Feed

Pedestal (PFP)

KD-1011

Large Capacity

Feeder (LCF)

KD-1012 A4/LT

Desk

MH-1700

Fig. 1-1

1 - 10

e-STUDIO230/280

Finisher

(

Hanging type

MJ-1022

(

Console saddle stitch type

Finisher

MJ-1025

)

Reversing Automatic

Document Feeder

MR-3016

)

Bridge Kit

KN-3520

Job Separator

MJ-5004

FAX Board

GD-1150NA/TW/EU

/AU/AS/C

2nd Line for FAX Board

GD-1160NA/TW/EU/C

Drawer Module

MY-1021

Paper Feed

Pedestal (PFP)

KD-1011

Large Capacity

Feeder (LCF)

KD-1012 A4/LT

Fig. 1-2

Desk

MH-1700

1 - 11

SPECIFICATIONS AND OUTLINE OF SYSTEM

e-STUDIO281c/351c/451c

Finisher

(

Hanging type

MJ-1022

)

e-STUDIO281c/351c only

Finisher

(

Console type

MJ-1023

Reversing Automatic

Document Feeder

MR-3018

)

(

Console saddle stitch type

Finisher

MJ-1024

Drawer Module

MY-1021

)

Paper Feed

Pedestal (PFP)

KD-1011

Large Capacity

Feeder (LCF)

KD-1012 A4/LT

Fig. 1-3

Bridge Kit

KN-3511

Desk

MH-1700

FAX Board

GD-1200

2nd Line for

FAX Board

GD-1160

FAX Board

GD-1201

2nd Line for

FAX Board

GD-1260

1 - 12

08/12

e-STUDIO352/353/452/453

Finisher

(

Hanging type

MJ-1022

)

e-STUDIO352/353 only

Finisher

(

Console type

MJ-1023

Reversing Automatic

Document Feeder

MR-3018

)

(

Console saddle stitch type

Finisher

MJ-1024

Drawer Module

MY-1021

)

Pedestal (PFP)

Finisher

(

Console type

MJ-1101

Paper Feed

KD-1011

)

Bridge Kit

Job Separator

Large Capacity

Feeder (LCF)

KD-1012 A4/LT

KN-3520

MJ-5004

FAX Board

GD-1200NA/TW/EU

/AU/AS/C/KR

2nd Line for FAX Board

GD-1160NA/TW/EU/C

FAX Board

GD-1201NA/TW/EU

/AU/AS/C/KR

2nd Line for FAX Board

GD-1260NA/TW/EU/C

Desk

MH-1700

Fig. 1-4

SPECIFICATIONS AND OUTLINE OF SYSTEM

1 - 13

08/03

e-STUDIO202L/203L/232/233/282/283 series

Finisher

(

Hanging type

MJ-1022

)

Reversing Automatic

Document Feeder

MR-3020

Automatic

Duplexing Unit

MD-0102

(

Console saddle stitch type

MJ-1025

Drawer Module

MY-1021

Finisher

)

Paper Feed

Pedestal (PFP)

KD-1011

Bridge Kit

KN-3520

Job Separator

MJ-5004

Large Capacity

Feeder (LCF)

KD-1012 A4/LT

FAX Board

GD-1150NA/TW/EU

/AU/AS/C/KR

2nd Line for FAX Board

GD-1160NA/TW/EU/C

FAX Board

GD-1151NA/TW/EU

/AU/AS/C/KR

2nd Line for FAX Board

GD-1260NA/TW/EU/C

Desk

MH-1700

Fig. 1-5

1 - 14

08/03

1.7 Units and Components

Control panel

1st Drawer

2nd Drawer

Fig. 1-6

Reversing Automatic Document Feeder (RADF)

Fig. 1-7

1 - 15

SPECIFICATIONS AND OUTLINE OF SYSTEM

1.8 Layout of PC Boards

e-STUDIO3511/4511/350/450/200L/202L/203L/230/232/233/280/282/283

MDM

FAX

NCU

Fig. 1-8 Rear side of the equipment

Symbol Name Function Remarks

FAX FAX control board Control the FAX function

MDM Telephone circuit control board Controls dialing for the analog cir-

cuit (for 2nd line)

NCU Telephone circuit control board Controls dialing for the analog cir-

cuit (Lower board: standard 1st line, Upper board: for 2nd line)

1 - 16

08/03

e-STUDIO281c/351c/451c, e-STUDIO352/353/452/453

NCU

MDM

FAX

FAX PWR

Fig. 1-9 Rear side of the equipment

Symbol Name Function Remarks

FAX FAX control board Controls the FAX function

MDM Telephone circuit control board Controls dialing for the analog cir-

cuit (for 2nd line)

NCU Telephone circuit control board Controls dialing for the analog cir-

cuit (Lower board: standard 1st line, Upper board: for 2nd line)

FAX PWR FAX power board Supplies the power (-12V, +24V)

of FAX

1 - 17

08/03

SPECIFICATIONS AND OUTLINE OF SYSTEM

1 - 18

2. LSU-RELATED FUNCTIONS

2.1 Recording Mode

This machine offers various printing modes such as the selection of the applicable recording paper and the recording method, etc. to meet users’ needs. To take full advantage of these features, it is important to understand the concepts of the recording paper selection algorithm and printing algorithm as described in 2. 2.

2 - 1

04/06

LSU-RELATED FUNCTIONS

+ 63 hidden pages