Toshiba G35-AV660 User Manual

G35-AV660
Series User’s Guide
If you need assistance:
Toshiba’s Support Web site
pcsupport.toshiba.com
Toshiba Global Support Centre
For more information, see “If Something Goes Wrong” on
page 293 in this guide.
GMAD00091010 08/06
2
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Model: Qosmio™ G35-AV660 Series Recordable and/or ReWritable Drive(s) and
Associated Software Warranty
The computer system you purchased may include Recordable and/or ReWritable optical media drive(s) and associated software, among the most advanced data storage technologies available. As with any new technology, you must read and follow all set-up and usage instructions in the applicable user guides and/or manuals enclosed or provided electronically. If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF.
Protection of Stored Data
For your important data, please make periodic back-up copies of all the data stored on the hard disk or other storage devices as a precaution against possible failures, alteration, or loss of the data. IF YOUR DATA IS ALTERED OR
LOST DUE TO ANY TROUBLE, FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM. WHEN COPYING OR TRANSFERRING YOUR DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED. TOSHIBA DISCLAIMS ANY LIABILITY FOR THE FAILURE TO COPY OR TRANSFER THE DATA CORRECTLY.
Critical Applications
NOTE
The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.
ACCORDINGLY, TOSHIBA, ITS AFFILIATES AND SUPPLIERS DISCLAIM ANY AND ALL LIABILITY ARISING OUT OF THE USE OF THE COMPUTER PRODUCTS IN ANY CRITICAL APPLICATIONS. IF YOU USE THE COMPUTER PRODUCTS IN A CRITICAL APPLICATION, YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.
FCC Notice “Declaration of Conformity Information”
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3
Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's parallel port, monitor port, USB port, PS/2 port port and microphone jack. Changes or modifications made to this equipment not expressly approved by Toshiba or parties authorized by Toshiba could void the user's authority to operate the equipment.
®
, i.LINK®
4
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference received, including interference
that may cause undesired operation.
Contact either:
Toshiba’s Support Web site at pcsupport.toshiba.com. Or call the Toshiba Global Support Centre:
Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273
Industry Canada Requirement
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conformé à la norme NMB-003 du
Canada.
FCC requirements
The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems.
This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, the information must be provided to the telephone company.
The modem connects to the telephone line by means of a standard jack called the USOC RJ11C.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC part 68 rules and requirements adopted by the ACTA. It is designed to be connected to a compatible modular jack that is also compliant.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by the ## are the REN without a
decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
Telephone Company Procedures
The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice, in writing, to allow you to make any changes necessary to maintain uninterrupted service.
If Problems Arise
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advanced notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
If trouble is experienced with this equipment, for repair or limited warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
5
Disconnection
If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.
Fax Branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including Fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number
6
provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)
In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer.
Alarm Equipment
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
Instructions for IC CS-03 Certified Equipment
1 NOTICE: The Industry Canada label identifies certified equipment.
This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
2 The user manual of analog equipment must contain the equipment’s
Ringer Equivalence Number (REN) and an explanation notice similar to the following:
The Ringer Equivalence Number (REN) of this device can be found on the label affixed to your computer.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
3 The standard connecting arrangement (telephone jack type) for this
equipment is jack type(s): USOC RJ11C.
Wireless Interoperability
The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to:
The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as defined
and approved by the Institute of Electrical and Electronics Engineers.
The Wireless Fidelity (Wi-Fi) certification as defined by the Wi-Fi Alliance.
The “Wi-Fi CERTIFIED” logo is a certification mark of the Wi-Fi Alliance.
Bluetooth® and Wireless LAN devices operate within the same radio
frequency range and may interfere with one another. If you use Bluetooth and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection.
If you should experience any such problem, immediately turn off your Bluetooth or Wireless LAN device.
Please contact Toshiba computer product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.
7
Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 GHz to
5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.
High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.
8
Wireless LAN and Your Health
Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:
Using the Wireless LAN equipment on board airplanes, or In any other environment where the risk of interference to other devices or
services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the Wireless LAN device prior to turning on the equipment.
Exposure to Radio Frequency Radiation The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is
far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. In normal operating configuration, the LCD in the upright position, the distance between the antenna and the user should not be less than 20 cm. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Antenna(s) used in 5.15 GHz to 5.25 GHz frequency band must be integral antenna which provide no access to the end user.
Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.
Regulatory Information
The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user
documentation that comes with the product. This device complies with the following radio frequency and safety standards.
Canada – Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s Web site www.hc-sc.gc.ca/rpb. The RF device shall not be co-located with any other transmitter that has not been tested with this device.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
Pour empecher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit etre utilize a l'interieur et devrait etre place loin des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel (ou son antenne d'emission) est installe a l'exterieur, il doit faire l'objet d'une licence.
9
This device is restricted to indoor use due to its operation in the 5.15 GHz to
5.25 GHz frequency range. Industry Canada requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.
High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.
10
NOTE
EU Declaration of Conformity
TOSHIBA declares that this product conforms to the following Standards:
Supplementary Information:
This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
VCCI Class B Information
Modem Warning Notice
*The product complies with the requirements of the Low Voltage Directive 72/23/EEC, the EMC Directive 89/336/ EEC and/or the R&TTE Directive 1999/ 05/EEC.
Conformity Statement
The equipment has been approved to [Commission Decision “CTR-21”] for pan­European single terminal connection to the Public Switched Telephone Network (PSTN).
However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
In the event of problems, you should contact your equipment supplier in the first instance.
The above Caution information applies to products that operate with an
802.11a device.
11
Taiwan
Article 14 Unless approved, for any model accredited low power radio frequency electric
machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.
Article 17 Any use of low power radio frequency electric machinery shall not affect
aviation safety and interfere with legal communications. In the event interference is caused, the use of such electric machinery shall be immediately discontinued. Operation of such products can be resumed only when they are modified and can no longer cause interference.
The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.
Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.
Using this Equipment in Japan
In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station).
1. Sticker Please put the following sticker on devices incorporating this product.
The frequency bandwidth of this equipment may operate within the same range as industrial devices, scientific devices, medical devices, microwave ovens, licensed radio stations and non-licensed specified low-power radio stations for mobile object identification systems (RFID) used in factory product lines (Other Radio Stations).
1. Before using this equipment, ensure that it does not interfere with any of the equipment listed above.
2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions.
3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations.
12
2. Indication The indication shown below appears on this equipment.
(3)
(1) (2)
2.4DSOF4
1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation.
OF: This equipment uses OFDM modulation.
3 The interference range of this equipment is less than 40m. 4 This equipment uses a frequency bandwidth from
2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems.
3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-15-1048 Direct Dial: 03-3457-4850 Fax: 03-3457-4868
(4)
Device Authorization
This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan.
The Name of the radio equipment: refer to the equipment label provided on the computer
JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT
Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018,
03GZDA0017
The following restrictions apply:
NOTE
NOTE
Do not disassemble or modify the device. Do not install the embedded wireless module into other device. 5.17 GHz to 5.23 GHz for indoor use only.
Radio Approvals for Wireless Devices
The following information is dependent on what type of wireless device is in your computer.
Approved Countries/Regions for use for the Atheros AR5BMB-43/44 and AR5BMB5 Mini PCI Wireless Network Adapters
This equipment is approved to the radio standard by the countries/regions in the following table.
Do not use this equipment except in the countries/regions in the following table.
13
This device works on passive scan only. A peer-to-peer mode is not available in 802.11a and Turbo Mode.
802.11b (2.4 GHz) Australia Austria Belgium
Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA
14
Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries
België/ Belgique:
Deutschland: License required for outdoor installations. Check with reseller for
France: Restricted frequency band: only channels 1 to 7 (2400 MHz and 2454
Italia: License required for indoor use. Use with outdoor installations not
Nederland: License required for outdoor installations. Check with reseller for
For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m. For registration and license please contact IBPT/BIPT.
Voor privé-gebruik buiten gebouw over publieke groud over afstand kleiner dan 300m geen registratie bij BIPT/IBPT nodig; voor gebruik over afstand groter dan 300m is wel registratie bij BIPT/IBPT nodig. Voor registratie of licentie kunt u contact opnemen met BIPT.
Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment, au­dessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprès de I’IBPT est requise. Pour les enregistrements et licences, veuillez contacter I’IBPT.
procedure to follow. Anmeldung im Outdoor-Bereich notwendig, aber nicht
genehmigungspflichtig.Bitte mit Händler die Vorgehensweise abstimmen.
MHz respectively) may be used outdoors in France. Please contact A.R.T. (http://www.art-telecom.fr) for applicable procedures to follow.
Bande de fréquence restreinte: seuls les canaux 1- 7 (2400 et 2454 MHz respectivement) doivent être utilisés endroits extérieur en France. Vous pouvez contacter I’Autorité de Régulation des Télécommuniations (http://www.art-telecom.fr) pour la procédure à suivre.
allowed. E’necessaria la concessione ministeriale anche per l’uso interno.
Verificare con i rivenditori la procedura da seguire.
procedure to follow. Licentie verplicht voor gebruik met buitenantennes. Neem contact op
met verkoper voor juiste procedure.
15
802.11a (5 GHz) Australia Austria Belgium
Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA
Turbo Mode (5 GHz)
Canada USA
Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries
European Community Countries
Austria O x x Belgium, France,
Switzerland/Lichtenstein Denmark, Finland,
Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK
Iceland, Spain O O O
O: allowed ×: forbidden
5150-5250 MHz
Channels: 36, 40, 44,
48
Indoor Only
OO x
OO O
5250-5350 MHz
Channels: 52, 56, 60,
64
Indoor Only
5470-5725 MHz
Channels: 100, 104, 108, 112,
116, 120, 124, 128, 132, 136, 140
Indoor/Outdoor
To remain in conformance with European spectrum usage laws for Wireless
LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply. The user should use the wireless LAN utility to check the current channel of operation. If operation is occurring outside of the allowable frequencies as listed above, the user must cease operating the Wireless LAN at that location and consult the local technical support staff responsible for the wireless network.
The 5 GHz Turbo mode feature is not allowed for operation in any
European Community country.
16
NOTE
This device must not be operated in ad-hoc mode using channels in the
5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point.
This device must be used with Access Points that have employed and
activated a radar detection feature required for European Community operation in the 5 GHz bands. This device will operate under the control of the Access Point in order to avoid operating on a channel occupied by any radar system in the area. The presence of nearby radar operation may result in temporary interruption of operation of this device. The Access Point’s radar detection feature will automatically restart operation on a channel free of radar. You may consult with the local technical support staff responsible for the wireless network to ensure the Access Point device(s) are properly configured for European Community operation.
Approved Countries/Regions for use for the Atheros AR5001X Mini PCI Wireless Network Adapter
This equipment is approved to the radio standard by the countries/regions in the following table.
Do not use this equipment except in the countries/regions in the following table.
This device works on passive scan only. A peer-to-peer mode is not available in 802.11a and Turbo Mode.
802.11b (2.4 GHz) Australia Austria Belgium
Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA
802.11a (5 GHz) Australia Austria Belgium
Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland UK USA
Turbo Mode (5 GHz)
Canada USA
Approved Countries/Regions for use for the Intel® PRO/ Wireless LAN 2100 3B Mini PCI Adapter
This equipment is approved to the radio standard by the countries/regions in the following table.
Do not use this equipment except in the countries/regions in the following table.
17
Argentina Australia Austria Belgium Brazil Canada Chile Denmark Finland France Germany Greece Iceland Ireland Italy Japan Liechtenstein Luxembourg Mexico Netherlands New Zealand Norway Peru Portugal Singapore Spain Sweden Switzerland UK Uruguay USA Venezuela
18
Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card
This equipment is approved to the radio standard by the countries/regions in the following table.
Do not use this equipment except in the countries/regions in the following table.
Australia Austria Belgium Canada Denmark Finland France Germany Greece Hong Kong Iceland Ireland Italy Japan Liechtenstein Luxembourg Malaysia Netherlands New Zealand Norway Philippines Portugal Singapore Spain Sweden Switzerland Thailand UK USA
Approved Countries/Regions for use for the INPROCOMM IPN2220 Wireless Network Adapter
This equipment is approved to the radio standard by the countries/regions in the following table.
Do not use this equipment except in the countries/regions in the following table.
EU Canada Japan USA Australia New Zealand
Bluetooth® Wireless Technology Interoperability
Bluetooth® Cards from TOSHIBA are designed to be interoperable with any
product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to:
Bluetooth Specification as defined and approved by The Bluetooth Special
Interest Group.
Logo certification with Bluetooth wireless technology as defined by The
Bluetooth Special Interest Group.
19
Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth products with all computers and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers.
Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA computer product support on Web site http://www.toshiba-europe.com/computers/tnt/ bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.
When you use Bluetooth cards from TOSHIBA close to 2.4 GHz Wireless LAN devices, Bluetooth transmissions might slow down or cause errors. If you detect certain interference while you use Bluetooth cards from TOSHIBA, always change the frequency, move your computer to the area outside of the interference range of 2.4 GHz Wireless LAN devices (40 meters/43.74 yards or more) or stop transmitting from your computer. Please contact TOSHIBA computer product support on Web site http://www.toshiba-europe.com/ computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.
Bluetooth and Wireless LAN devices operate within the same radio frequency range and may interfere with one another. If you use Bluetooth and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection. If you should experience any such problem, immediately turn off either one of your Bluetooth or Wireless LAN. Please contact Toshiba computer product support on Web site http://www.toshiba-europe.com/computers/tnt/ bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.
Bluetooth® Wireless Technology and Your Health
The products with Bluetooth® wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
20
In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:
Using the equipment with Bluetooth wireless technology on board
airplanes, or
In any other environment where the risk of interference to other devices or
services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the device with Bluetooth wireless technology prior to turning on the equipment.
Exposure to Radio Frequency Radiation The radiated output power of the Bluetooth Card from TOSHIBA is far below
the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled environment, the Bluetooth Card from TOSHIBA has to be operated while maintaining a minimum body to antenna distance of 20 cm.
Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information.
The Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits.
Nevertheless, it is advised to use the Bluetooth Card from TOSHIBA in such a manner that human contact during normal operation is minimized.
Regulatory statements
This product complies with any mandatory product specification in any country/ region where the product is sold. In addition, the product complies with the following:
European Union (EU) and EFTA
This equipment complies with the R&TTE directive 1999/5/EC and has been provided with the CE mark accordingly.
Canada — Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
21
Taiwan
Article 14 Unless approved, for any model accredited low power radio frequency
electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.
Article 17 Any use of low power radio frequency electric machinery shall not affect
aviation safety and interfere with legal communications. In the event interference is caused, the use of such electric machinery shall be immediately discontinued. Operation of such products can be resumed only when they are modified and can no longer cause interference.
The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.
Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.
Using this Equipment in Japan
In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station).
1. Sticker
Please put the following sticker on devices incorporating this product.
The frequency bandwidth of this equipment may operate within the same range as industrial devices, scientific devices, medical devices, microwave ovens, licensed radio stations and non-licensed specified low-power radio stations for mobile object identification systems (RFID) used in factory product lines (Other Radio Stations).
1. Before using this equipment, ensure that it does not interfere with any of the equipment listed above.
2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions.
3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations.
22
2. Indication The indication shown below appears on this equipment.
(1) (2)
(3)
2.4FH1
(4)
1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to
2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems.
3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-15-1048 Direct Dial: 03-3457-4850 Fax: 03-3457-4868
Device Authorization
This device obtains the Technical Regulation Conformity Certification, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law of Japan.
The Name of the radio equipment: EYXF2CS TELECOM ENGINEERING CENTER Approval Number: 01NYDA1305 The following restrictions apply:
Do not disassemble or modify the device. Do not install the embedded wireless module into other device.
Optical Drive Safety Instructions
The HD DVD-ROM and multi-function drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Never attempt to disassemble, adjust or repair a HD DVD, CD/DVD drive, CD-RW drive, Multi-drive or any other optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury. Always contact an authorized Toshiba service provider, if any repair or adjustment is required.
Location of the Required Label
(Sample shown below. Location of the label and manufacturing information may vary.)
23
This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT. To use this model properly, read the user’s guide carefully and keep it for your future reference.
Never attempt to disassemble, adjust or repair a HD DVD, CD/DVD drive, CD-RW drive, Multi-drive or any other optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury. Always contact an authorized Toshiba service provider, if any repair or adjustment is required.
24
Copyright
This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
©2006 by Toshiba America Information Systems, Inc. All rights reserved.
Export Administration Regulation
This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and may be subject to the approval of the U.S. Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the U.S. Export Administration Regulations is prohibited.
Notice
The information contained in this manual, including but not limited to any product specifications, is subject to change without notice.
TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT, CONTRACT OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.
Trademarks
Qosmio is a trademark of Toshiba America Information Systems, Inc. and/or Toshiba Corporation.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.
HD DVD Application Logo (HD DVD-ROM) represents the optical drives compliance with the HD DVD physical format, and does not represent compliance with the specification for the HD DVD General Logo defined by the DVD Forum.
Direct3D, DirectSound, and DirectMusic are registered trademarks of Microsoft Corporation.
DirectX, Active Desktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation.
ConfigFree is a trademark of Toshiba Corporation. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Home Theater is a trademark of Dolby Laboratories. Secure Digital and SD are trademarks of the Secure Digital Association. xD-Picture Card is a trademark of Fuji Photo Film Co. Ltd. MultiMediaCard is a trademark of Infineon Technologies AG. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Intel, Intel Core, Celeron, Centrino and Pentium are trademarks or registered
trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
ExpressCard is a trademark of PCMCIA. i.LINK is a registered trademark of Sony Corporation. Adobe and Photoshop are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/or other countries. Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any
use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.
All other brand and product names are trademarks or registered trademarks of their respective companies.
25
26
Computer Disposal Information
This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at
www.eiae.org.

Contents

Introduction................................................................................ 37
This guide ...............................................................38
Safety icons ............................................................39
Other icons used...............................................40
Other documentation ..............................................40
Service options .......................................................41
Chapter 1: Getting Started......................................................... 42
Selecting a place to work ........................................42
Creating a computer-friendly environment........42
Keeping yourself comfortable ...........................43
Precautions.......................................................43
Important information on your computer’s
cooling fan..................................................45
Setting up your computer .......................................46
Setting up your software...................................47
Registering your computer with Toshiba ................48
Adding optional external devices.............................49
Connecting to a power source ................................49
Charging the main battery.......................................53
27
28
Contents
Using the computer for the first time......................54
Opening the display panel.................................54
Your computer’s features and specifications ....55
Turning on the power .......................................56
Adding memory (optional)......................................57
Installing a memory module .............................57
Removing a memory module............................63
Checking total memory.....................................65
Using the Dual Mode Pad .......................................65
Using external display devices................................68
Connecting the display device...........................69
Directing the display output when you
turn on the computer..................................73
Adjusting the quality of the external display......75
Connecting External AV Input Devices ....................75
Using an external keyboard.....................................78
Using a mouse........................................................78
Connecting a printer ...............................................78
Setting up a printer ...........................................79
Connecting an optional external diskette drive........80
Turning off the computer........................................81
Options for turning off the computer ................81
Using the Turn Off Computer or Shut Down
commands..................................................84
Using and configuring Hibernation mode .........87
Using and configuring Standby mode...............89
Closing the display panel ..................................90
Caring for your computer........................................91
Cleaning the computer......................................91
Moving the computer........................................91
Using a computer lock......................................92
Contents
29
Chapter 2: Learning the Basics................................................. 93
Computing tips .......................................................93
Using the keyboard.................................................95
Character keys .................................................95
Making your keyboard emulate a full-size
keyboard.....................................................95
Ctrl, Fn, and Alt keys.........................................96
Function keys....................................................96
Windows special keys ......................................97
Overlay keys .....................................................97
Using the overlay to type numeric data.............98
Starting a program..................................................98
Starting a program from the Start menu...........99
Starting a program from Windows® Explorer....99
Starting a program from the Run dialog box ..100
Saving your work..................................................101
Printing your work ................................................103
Backing up your work ...........................................104
Restoring your work .......................................105
Using the optical drive ..........................................105
Drive components and control buttons...........106
Inserting a disc ..............................................108
Playing an audio CD........................................110
Playing a CD/DVD ...........................................111
Creating a CD/DVD..........................................111
Removing a disc with the computer on...........112
Removing a disc with the computer off ..........113
Caring for CD or DVD discs ...........................113
Toshiba’s online resources ...................................114
Contents
30
Chapter 3: Mobile Computing.................................................115
Toshiba’s energy-saver design..............................115
Running the computer on battery power ..............115
Battery Notice .................................................116
Power management........................................117
Using additional batteries ...............................117
Charging batteries.................................................118
Charging the main battery...............................118
Charging the RTC battery................................119
Monitoring main battery power.............................120
Determining remaining battery power.............122
What to do when the main battery runs low ...123
Setting battery alarms.....................................123
Conserving battery power ..............................124
Power Profiles ................................................125
Using a hot key to set the Power Profile .........126
Changing the main battery....................................127
Removing the battery from the computer .......127
Inserting a charged battery .............................129
Taking care of your battery ...................................130
Safety precautions ..........................................130
Maintaining your battery.................................131
Disposing of used batteries ..................................133
Traveling tips ........................................................134
Chapter 4: Exploring Your Computer’s Features...................135
Exploring the desktop ...........................................135
Finding your way around the desktop .............136
Setting up for communications.............................138
Connecting the modem to a telephone line.....140
Connecting your computer to a network.........141
An overview of using the Internet .........................144
The Internet ....................................................144
The World Wide Web .....................................144
Contents
31
Internet Service Providers ..............................145
Connecting to the Internet .............................145
Surfing the Internet.........................................146
Internet features..............................................146
Uploading to, and downloading files from,
the Internet ..............................................147
Exploring audio features .......................................147
Recording sounds...........................................147
Using external speakers or headphones..........149
Using PC Cards.....................................................150
Inserting a PC Card.........................................150
Removing a PC Card.......................................151
Setting up a PC Card for your computer .........152
Using an ExpressCard™........................................152
Inserting an ExpressCard™.............................152
Removing an ExpressCard™...........................153
Using the Bridge Media Adapter Slot ....................153
Inserting memory media.................................154
Removing memory media...............................155
Using the i.LINK® port...........................................156
Using QosmioPlayer .............................................156
Using the Media Control Buttons ....................157
Playing an audio CD........................................158
Playing a DVD.................................................159
Watching television.........................................160
Toshiba Remote Control .................................162
Installing the QosmioPlayer Recovery media........167
Chapter 5: Getting to Know the Windows® XP Media Center
Edition 2005....................................................168
Media Center Setup...............................................169
Connecting to a Television..............................169
Connecting the TV Signal Source When
You Have an Existing Setup ......................171
32
Contents
Starting the Media Center .....................................173
Using Media Center...............................................179
Using the Toshiba Remote Control with
Media Center.............................................181
Watching Television Programs .............................188
Selecting a Program from the TV Guide..........189
Watching a Recorded TV Program..................191
Changing a scheduled recording.....................191
Searching for a TV Program to Watch ............192
Recording TV........................................................193
Recording TV tips ...........................................194
Recording from the Guide...............................195
Recording from Search...................................196
Recording Manually........................................197
Changing Your Settings ..................................197
Changing recording priorities .........................198
Listening to Music ................................................199
Creating Your Music Library Using
Windows Media® Player............................199
Adding Music from Your Hard Drive to
Windows Media Player Library .................201
Playing Digital Music Files ..............................202
Finding Music Files in My Music.....................203
Playing a Song................................................204
Setting Up an Automatic Disc Jockey .............205
Finding and Playing an Album.........................205
Creating a Playlist ...........................................206
Displaying Your Pictures.......................................208
Viewing a Slide Show......................................210
Sorting your Pictures......................................210
Watching Your Digital Movies...............................211
Organizing Your Videos ..................................211
Playing Digital Videos .....................................212
Playing a Video in Full Screen Mode...............213
Contents
33
Sorting Videos ................................................213
Watching a DVD/HD DVD......................................214
Stopping a DVD Movie....................................215
Playing a DVD movie already in your drive .....215
Changing the Media Center Settings.....................216
More Programs.....................................................225
Online Spotlight ....................................................226
Getting Help for Media Center...............................227
Chapter 6: Using the TOSHIBA RAID Utility..........................228
Using RAID ...........................................................228
RAID-0............................................................229
RAID-1............................................................230
When you first start your computer................231
Creating a new RAID-0 array.................................233
TOSHIBA RAID Console Utility..............................236
Defining options for RAID-0 or RAID-1...........238
Viewing the status of an array.........................241
Viewing the status of a hard disk drive ...........243
Performing a media check on a RAID-1 array.245
Breaking a RAID-0 array (striping)..................246
Breaking a RAID-1 array (mirror)....................248
Rebuilding the data on the secondary disk in a
RAID-1 array...................................................249
Restoring a failed drive in a RAID-1 array.............251
Error message examples.......................................252
Chapter 7: Toshiba Utilities...................................................... 253
TOSHIBA Assist ....................................................254
Connect...........................................................255
Secure.............................................................256
Protect & Fix...................................................257
Optimize..........................................................258
Setting passwords ................................................259
34
Contents
Using an instant password..............................259
Using a user password ...................................260
Using a supervisor password..........................261
PC Diagnostic Tool Utility .....................................262
Fn-esse®...............................................................263
Starting Fn-esse® ...........................................264
Using drag-and-drop to assign a key..............265
Using the keyboard or pointing device to
assign a key ..............................................265
Viewing existing key assignments...................267
Changing or removing existing key
assignments ............................................267
TOSHIBA Hotkey Utility ........................................268
TOSHIBA SD™ Memory Card Format Utility .........269
TOSHIBA Power Saver..........................................270
Preset Power Profiles .....................................271
Quickly creating a new power profile ..............271
Customizing a power profile ...........................271
Mouse Utility ........................................................272
Toshiba Hardware Setup.......................................273
TOSHIBA Zooming Utility......................................275
CD/DVD Drive Acoustic Silencer ...........................277
TOSHIBA Accessibility ..........................................278
Fingerprint Authentication Utility...........................279
Fingerprint utility limitations ...........................279
Fingerprint Enrollment ....................................280
Fingerprint Logon ...........................................281
Power-on Security ..........................................282
Control Center.................................................284
Password Bank ...............................................285
Care and maintenance of your fingerprint
reader .......................................................290
Fingerprint reader limitations..........................292
Contents
35
Chapter 8: If Something Goes Wrong ................................... 293
Problems that are easy to fix ................................293
Problems when you turn on the computer............295
The Windows® operating system is not working ..298
Using Startup options to fix problems ............299
Internet problems ...........................................300
The Windows® XP operating system can
help you....................................................301
Resolving a hardware conflict...............................301
A plan of action...............................................302
Resolving hardware conflicts on your own .....302
Fixing a problem with Device Manager ...........304
Memory problems ..........................................306
Power and the batteries ..................................307
Keyboard problems.........................................308
Display problems............................................309
Disk drive problems........................................312
Optical drive problems....................................314
Sound system problems.................................315
PC Card problems...........................................316
Printer problems.............................................319
Modem problems............................................320
Wireless networking problems .......................321
DVD operating problems.......................................324
Develop good computing habits ...........................327
Data and system configuration backup in
Windows XP .............................................328
If you need further assistance...............................334
Before you contact Toshiba ............................334
Contacting Toshiba .........................................335
Other Toshiba Internet Web sites..........................336
Toshiba’s worldwide offices..................................336
Contents
36
Appendix A: Hot Keys..............................................................338
Volume Mute ........................................................338
Password security ................................................339
Without a password........................................339
With a password.............................................339
Maintaining security when the battery is
not fully charged.......................................340
Power profile .......................................................341
Standby mode.......................................................341
Hibernation mode ................................................342
Display modes ......................................................343
Display brightness ................................................344
Enabling a wireless device ...................................344
Disabling or enabling the Dual Mode Pad .............345
Zooming applications in/out .................................345
Keyboard hot keys ...............................................346
Appendix B: Power Cord/Cable Connectors..........................347
Appendix C: Using ConfigFree™ with your
Toshiba Computer .............................................. 348
Getting Started......................................................349
Starting ConfigFree .........................................349
ConfigFree Utilities................................................351
Connectivity Doctor ........................................351
Search for Wireless Devices ...........................354
Profile Settings ...............................................360
ConfigFree SUMMIT........................................363
Quick Connect.................................................367
Using the Automatic Switch..................................370
Semi-Automatic Switch Feature............................371
Glossary....................................................................................372
Index..........................................................................................387

Introduction

NOTE
Welcome to the world of powerful, portable, multimedia computing. With your Toshiba notebook computer, your work and entertainment can accompany you wherever you go.
This notebook is compatible with European Union Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances in electrical and electronic equipment (RoHS), which restricts use of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE. Toshiba requires its notebook component suppliers to meet RoHS requirements and verifies its suppliers’ commitment to meeting RoHS requirements by conducting component sampling inspections during the product design approval process.
37
38
NOTE
NOTE
Introduction

This guide

Certain Microsoft® software product(s) included with this computer may use technological measures for copy protection. IN SUCH EVENT, YOU WILL NOT BE ABLE TO USE THE PRODUCT IF YOU DO NOT FULLY COMPLY WITH THE PRODUCT ACTIVATION PROCEDURES. Product activation procedures and Microsoft’s privacy policy will be detailed during initial launch of the product, or upon certain reinstallations of the software product(s) or reconfigurations of the computer, and may be completed by Internet or telephone (toll charges may apply).
Some software may differ from its retail version (if available), and may not include user manuals or all program functionality.
The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba’s Web site at
pcsupport.toshiba.com.
While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/component/ options availability are all subject to change without notice. For the most up-to-date product information about your computer, or to stay current with the various computer software or hardware options, visit Toshiba’s Web site at pcsupport.toshiba.com.
This guide
This guide introduces the computer’s features. You can:
Read the entire guide from beginning to end. Skim through and stop when a topic interests you. Use the table of contents and the index to find specific
information.

Safety icons

NOTE
This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows:
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Introduction
Safety icons
39
Indicates a potentially hazardous situation which, if not avoided, may result in property damage.
Provides important information.
Introduction
40

Other documentation

Other icons used

Additional icons highlight other helpful or educational information:
TECHNICAL NOTE: This icon indicates technical information about the computer.
HINT: This icon indicates helpful hints and tips.
DEFINITION: This icon indicates the definition of a term used in the text.
Other documentation
Your computer comes with the following documentation:
An electronic version of the user’s guide (this document) It may also contain guides for other programs that may
come with your system.
For accessory information, visit Toshiba’s Web site at
accessories.toshiba.com.

Service options

Toshiba offers a full line of optional service programs to complement its limited warranty. Toshiba’s standard limited warranty, extended warranty, and service upgrade terms and conditions are available at warranty.toshiba.com.
To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at
pcsupport.toshiba.com.
If you have a problem or need to contact Toshiba, see “If
Something Goes Wrong” on page 293.
Introduction
Service options
41
Chapter 1
Getting Started
This chapter provides tips for working comfortably, summarizes how to connect components, and explains what to do the first time you use your notebook computer.

Selecting a place to work

Your computer is portable and designed to be used in a variety of circumstances and locations.

Creating a computer-friendly environment

Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer. Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat.
42
To keep your computer in prime operating condition, protect your work area from:
Dust, moisture, and direct sunlight. Equipment that generates a strong electromagnetic field,
such as stereo speakers (other than speakers that are connected to the computer) or speakerphones.
Rapid changes in temperature or humidity and sources of
temperature change such as air conditioner vents or heaters.
Extreme heat, cold, or humidity. Liquids and corrosive chemicals.

Keeping yourself comfortable

The Toshiba Instruction Manual for Safety and Comfort, that shipped with your computer, contains helpful information for setting up your work environment and tips for working comfortably throughout the day.
Getting Started
Selecting a place to work
43

Precautions

Your computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to the computer.
Avoid prolonged physical contact with the underside or
surface of the computer.
44
Getting Started
Selecting a place to work
Never allow any liquids to spill into any part of your computer, and never expose the computer to rain, water, seawater or moisture. Exposure to liquid or moisture can cause electric shock or fire, resulting in damage or serious injury. If any of these eventualities should accidentally occur, immediately:
1. Turn off the computer.
2. Disconnect the AC adaptor from the power plug socket and computer.
3. Remove the battery pack.
Failure to follow these instructions could result in serious injury or permanent damage to the computer.
Do not turn on the power again until you have taken the computer to an authorized service center.
Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injury to skin.
Read the enclosed Instruction Manual for Safety and Comfort.
Never place a heavy object on the computer and be careful not to drop a heavy object onto the computer. It could damage the computer or cause system failure.
Getting Started
Selecting a place to work
Never turn off the computer if a drive light indicates a
drive is active. Turning off the computer while it is reading from or
writing to a disk/disc or flash media may damage the disk/disc or flash media, the drive, or both.
Keep the computer and disks away from objects that
generate strong magnetic fields, such as large stereo speakers.
Information on disks is stored magnetically. Placing a magnet too close to a disk can erase important files.
Handle discs carefully. Avoid touching the surface of the disc. Grasp it by its center hole and edge. If you handle the disc incorrectly, you could damage the disc and possibly lose data.
Scan all new files for viruses.
This precaution is especially important for files you receive via email or download from the Internet. Occasionally, even new programs you buy from a supplier may contain a computer virus. You need a special program to check for viruses. Ask your dealer to help you.
45

Important information on your computer’s cooling fan

Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer.
46
NOTE
Getting Started

Setting up your computer

Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Standby mode). In this condition, observe the following:
Never cover your computer or AC adaptor with any
object.
Never place your computer or AC adaptor near a heat
source, such as an electric blanket or heater.
Never block the air vents. Always operate your computer on a hard surface. Using
your computer on a carpet or other soft material can block the vents.
Overheating your computer or AC adaptor could cause system failure, computer or AC adaptor damage or a fire, possibly resulting in serious injury.
The cooling fan location will vary depending on the computer.
Setting up your computer
TECHNICAL NOTE: You must complete all setup steps up to and including “Setting up your software” on page 47 before adding external or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC Cards.
Your computer contains a rechargeable main battery that needs to be charged before you can use it.
To use external power or to charge the battery you must attach the AC adaptor. See “Connecting to a power source”
on page 49.

Setting up your software

NOTE
When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely.
The names of windows displayed, and the order in which windows appear, may vary according to your software setup choices.
The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software.
1 From the Welcome screen click Next to enter the Setup
Wizard.
2 Confirm acceptance of Microsoft’s End User License
Agreement and click Next.
Getting Started
Setting up your computer
47
3 Select the appropriate option from the Help Protect Your
Computer screen and click Next.
4 Enter the computer name and description and click Next
or Skip.
5 Select how your computer will connect to the Internet
and click Next. The computer will pause for a moment while checking
for an Internet connection.
Getting Started
NOTE
NOTE
48

Registering your computer with Toshiba

If an Internet connection could not be found, a window will display the message: “An Internet connection could not be chosen.” Click Next to continue.
If you are connecting your computer to a network, consult your system administrator before you choose your computer name and network settings.
6 Follow the remaining screen prompts to complete the
setup process. Once you click the final screen, your computer restarts
automatically.
Registering your computer with Toshiba
Product registration is strongly recommended, and allows Toshiba to send you periodic updates, announcements, and special offers applicable to your product. Product registration can be completed during the initial start up process of your computer. If you decide not to register at that time, you can either double-click the icon on your desktop or go to the Toshiba Web site at www.register.toshiba.com at a later time. Failure to complete Product Registration will not diminish Customer rights under the Toshiba limited Warranty.
To register online, you must be connected to the Internet.
Getting Started
NOTE

Adding optional external devices

Adding optional external devices
Before adding external devices or memory, Toshiba recommends setting up your software. See “Setting up your
software” on page 47.
After starting your computer for the first time you may want to:
Add more memory (see “Adding memory (optional)” on
page 57)
Connect a mouse (see “Using a mouse” on page 78) Connect a full-size keyboard (see “Using an external
keyboard” on page 78)
Connect an external monitor (see “Using external display
devices” on page 68)
Connect a local printer (see “Connecting a printer” on
page 78)
Connect an optional external disk drive (see “Connecting
an optional external diskette drive” on page 80)
Install PC Cards (see “Using PC Cards” on page 150)
49

Connecting to a power source

Your computer requires power to operate. Use the power cord/cable and AC adaptor to connect the computer to a live electrical outlet, or to charge the computer’s battery.
Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug directly. Failure to follow this instruction may damage the cord/cable, and/or result in a fire or electric shock, possibly resulting in serious injury.
50
Getting Started
Connecting to a power source
Always confirm that the power plug (and extension cable plug if used) has been fully inserted into the socket, to ensure a secure electrical connection. Failure to do so may result in a fire or electric shock, possibly resulting in serious injury.
Be careful if you use a multiple connector. An overload on one socket could cause a fire or electric shock, possibly resulting in serious injury.
Always use the TOSHIBA AC adaptor that was provided with your computer and the TOSHIBA Battery Charger (that may have been provided with your computer), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the computer possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor or charger.
AC adaptor
Power cord/cable
AC adaptor cord
(Sample Illustration) Power cord/cable and AC adaptor
Getting Started
Connecting to a power source
To connect AC power to the computer:
1 Connect the power cord/cable to the AC adaptor.
(Sample Illustration) Connecting the power cord/cable to the AC adaptor
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
51
2 Plug the AC adaptor cord into the DC-IN on the back of
the computer.
(Sample Illustration) Connecting the AC adaptor cord to the computer
52
NOTE
Getting Started
Connecting to a power source
3 Connect the power cord/cable to a live electrical outlet.
The AC power light on the indicator panel glows blue.
Never attempt to connect or disconnect a power plug with wet hands. Failure to follow this instruction could result in an electric shock, possibly resulting in serious injury.
The computer’s main battery light gives you an indication of the main battery’s current charge:
Glows amber while the main battery is being charged
(AC adaptor connected)
Glows blue when the main battery is fully charged Is unlit when the main battery has discharged, the
battery is not charging, or the AC adaptor is not plugged into the computer or AC outlet
Flashes amber when the main battery charge is low
and it is time to recharge the main battery or plug in the AC adaptor
If the AC power light flashes amber during charging, either the main battery is malfunctioning, or it is not receiving correct input from the AC power supply.
Disconnect the AC power cord/cable and remove the main battery pack. See “Changing the main battery” on
page 127 for information on replacing the main battery.

Charging the main battery

NOTE
Charging the main battery
Your computer came with its battery already installed. Before using the battery to power the computer, you must charge the battery.
To charge the battery, leave the computer plugged into an AC power source with the computer turned off until the battery light glows blue. After that, the battery will be completely charged and ready to power the computer.
Once the battery is charged for the first time, avoid leaving the computer plugged in and turned off for more than a few hours at a time. Continuing to charge a fully charged battery can damage the battery.
TECHNICAL NOTE: The recharging of the battery cannot occur when your computer is using all of the power provided by the AC adaptor to run applications, features, and devices. Your computer’s Power Saver utility can be used to select a power level setting that reduces the power required for system operation and will allow the battery to recharge.
Getting Started
53
Battery life and charge time may vary depending on the applications, power management settings, and features used.
Getting Started
NOTE
54

Using the computer for the first time

Using the computer for the first time
The computer is now ready for you to turn it on and begin using it.

Opening the display panel

1 Press the display release button. 2 Lift the display panel.
(Sample Illustration) Opening the display panel
When opening or closing the LCD display panel, place one hand on the palm rest to hold the computer in place and use the other hand to slowly open or close the LCD display panel.
To avoid damaging the LCD display panel, do not force it beyond the point where it moves easily and never lift the computer by the LCD display panel.
Do not press or push on the LCD display panel and be careful to remove any pens or other objects from the keyboard area before closing the LCD display panel.
Getting Started
Using the computer for the first time
Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology. Over a period of time, and depending on the usage of the computer, the brightness of the screen will deteriorate. This is also an intrinsic characteristic of the screen technology. When the computer is operated on battery power, the screen will dim and you may not be able to increase the brightness of the screen while on battery power.

Your computer’s features and specifications

Certain notebook chassis are designed to accommodate all possible configurations for an entire product Series. Your select model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
55
This information applies to all the features and icons described in this guide.
Below are examples of some of the many possible icons used on your computer:
(Sample Illustration) System icons
Getting Started
56
Using the computer for the first time

Turning on the power

To turn on the computer:
1 Make sure any external devices (such as the AC adaptor,
if you plan to use AC power rather than battery power) are properly connected and ready.
2 Check to ensure that all optical drives are empty. 3 Press and hold the power button in until the power button
and the on/off light on the system indicator panel glow blue—about one second.
(Sample Illustration) Turning on the power
The preinstalled operating system will load automatically.
When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely.

Adding memory (optional)

NOTE
Adding memory (optional)
HINT: To purchase additional memory modules, see the accessories information packaged with your system or visit
accessories.toshiba.com.
Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data.
Before adding external devices or memory, Toshiba recommends setting up your software. See “Setting up your
software” on page 47.

Installing a memory module

Getting Started
57
Additional memory modules can be installed in the memory module slots on the base of the computer. You will need a small Phillips screwdriver for this procedure.
If you use the computer for a long time, the memory module will become hot. If this happens, let the module cool to room temperature before you replace it.
To avoid damaging the computer’s screws, use a small Phillips screwdriver that is in good condition.
Installing a memory module with the computer’s power on may damage the computer, the module, or both.
58
Getting Started
Adding memory (optional)
The computer has two memory slots—Slot A and Slot B. You can install one or two memory modules.
Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Standby or Hibernation mode, data will be lost.
If the computer is on, begin at step 1; otherwise, skip to step 3.
1 Click Start, and then Turn off computer or Shut Down
(depending on the system). The Turn off computer or Shut Down window appears.
2 Click Turn Off or Shut Down.
The operating system turns off the computer.
3 Unplug and remove any cables connected to the
computer, including the AC adaptor.
4 Remove the main battery. For information on removing
the main battery, see “Removing the battery from the
computer” on page 127.
5 Close the display panel and turn the computer upside
down to locate the memory module slot cover.
Memory module slot cover
Front of computer
(Sample Illustration) Locating the memory module slot cover
Getting Started
Adding memory (optional)
6 Using a small Phillips screwdriver, loosen the captive
screw that secures the memory module slot cover.
Front of computer
(Sample Illustration) Unscrewing the memory module slot cover
7 Remove the memory module slot cover.
59
8 Place the cover in a safe place so that you can retrieve it
later.
Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up.
Avoid touching the connector on the memory module or on the computer. Grease or dust on the connector may cause memory access problems.
60
NOTE
NOTE
Getting Started
Adding memory (optional)
9 Carefully remove the new memory module from its
antistatic packaging, without touching its connector.
10 Locate an empty memory module slot on the underside of
the computer.
If no memory slot is available, you must remove a module by performing steps 2-3 of “Removing a memory module” on
page 63.
If your system has the memory modules stacked on top of one another, you must remove the top module first before removing/installing the bottom module.
11 Pick up the memory module by its sides, avoiding any
contact with its connector. Position the module toward the socket, aligning the connector’s notch with the matching key in the socket.
notch
latch
connector
latch
key
(Sample Illustration) Aligning the memory module with the socket
Getting Started
Adding memory (optional)
12 Firmly press the memory module into the memory slot’s
socket at approximately a 30-degree angle (to the horizontal surface of the computer).
(Sample Illustration) Inserting the memory module into the socket
13 Once the module’s connector is fully inserted into the
socket, press downward on the top edge of the module to seat the module into the latches at the sides of the socket. These latches should “snap” into place securely with the corresponding cutouts in the side of the module. If the latches and cutouts do not line up correctly, repeat steps
12-13.
61
latch
latch
(Sample Illustration) Pressing down on the memory module
62
Getting Started
Adding memory (optional)
Do not force the memory module into position. The memory module should be completely inserted into the socket and level when secured in place.
Memory slots
Front of computer
(Sample Illustration) Inserting the memory module into the slot
14 Replace the memory module slot cover and secure it
using the screw.
15 Re-insert the main battery. For more information on
inserting the main battery, see “Inserting a charged
battery” on page 129.
16 Turn the computer right side up. 17 Reconnect the cables. 18 Restart the computer.
TECHNICAL NOTE: You must have at least one memory module installed for the computer to work.
You can now continue setting up the computer. When the operating system has loaded, you can verify that the computer has recognized the additional memory module.
If you are adding an extra memory module after setting up the computer, verify that the computer has recognized it correctly as described in “Checking total memory” on page 65.

Removing a memory module

If you need to remove a memory module:
1 Complete steps 18 in “Installing a memory module” on
page 57 to shut down the computer and open the memory
module slot cover.
Do not try to remove a memory module with the computer turned on. You can damage the computer and the memory module.
Do not remove the memory module while the computer is in Standby or Hibernation mode. The computer could hang up the next time you turn it on and data in memory will be lost. In either of the above cases, the Standby configuration will not be saved.
Getting Started
Adding memory (optional)
63
The following message appears when you turn on the power: Warning: Resume Failure
Press Any Key to Continue If the computer hangs up when you turn it on, perform the
following: Press the power button and hold it down for at least ten seconds, then turn the power on again.
64
NOTE
Getting Started
Adding memory (optional)
2 Pull the latches away from the memory module.
The memory module pops up slightly.
If your system has the memory modules stacked on top of one another, you must remove the top module first before removing/installing the bottom module.
3 Gently lift the memory module to a 30-degree angle and
slide it out of the slot.
Memory slots
Front of computer
(Sample Illustration) Removing the memory module
4 Replace the memory module slot cover and secure it
using the screw.
5 Re-insert the main battery. For more information on
inserting the main battery, see “Inserting a charged
battery” on page 129.
6 Turn the computer right side up. 7 Reconnect the cables.
8 Restart the computer.
TECHNICAL NOTE: You must have at least one memory module installed for the computer to work.

Checking total memory

When you add or remove a memory module, you can check that the computer has recognized the change. To do this:
1 Click Start, Control Panel, Performance and
Maintenance, and then System.
2 The General tab view automatically appears and shows
total memory.
If the computer does not recognize the memory configuration, turn off the computer and remove the memory module slot cover (complete steps 1-8 in “Installing a
memory module” on page 57), and then check that the
module is inserted completely into the socket and lined up squarely with the socket latches.
Getting Started

Using the Dual Mode Pad

65
Using the Dual Mode Pad
The Dual Mode feature allows you to switch between Cursor Mode (the default mode) and Button Mode.
In Button Mode, you can use the virtual buttons on the Dual Mode Pad which provide convenient shortcuts to frequently used applications. You can also use the volume control bar to adjust the system volume quickly and easily.
Using the Virtual Buttons
The Dual Mode Pad has six virtual buttons and a volume control bar. Each virtual button can be configured to start an application. The volume control bar is used to adjust the system volume level.
66
NOTE
Getting Started
Using the Dual Mode Pad
Virtual buttons
123
Virtual buttons
Mode switch button
Volume control bar
(Sample Illustration) Virtual buttons on the Dual Mode Pad
Activating the Dual Mode Pad will deactivate an external mouse.
The virtual buttons at the top of the Dual Mode Pad have the following default settings:
Left button: Opens the assigned email application Middle button: Opens the ConfigFree utility (see the
Toshiba online Help for more information)
Right button: Sends the item in the active window to the
printer
The other three virtual buttons have no default settings. You must configure these buttons in the Mouse Properties dialog box before they can be used.
In order to use the virtual buttons you must first enable Dual Mode in the Mouse Properties dialog box. After that, you can use the virtual buttons as follows:
1 Tap the mode switch button to enable the virtual buttons. 2 Tap the virtual button assigned to the application you
wish to launch, or slide your finger on the volume control bar to adjust the volume to the desired level.
3 When the operation is complete, the Dual Mode Pad
automatically disables the virtual buttons.
Getting Started
NOTE
Using the Dual Mode Pad
The virtual buttons cannot be used until the mode switch button is tapped again.
The virtual buttons and Dual Mode can be enabled or changed in the Mouse Properties dialog box.
Enabling Dual Mode
To enable Dual Mode:
1 Click Start, Control Panel.
The Control Panel window appears.
2 Click Mouse.
The Mouse Properties window appears.
3 Click the Device Settings tab, then Settings.
The Properties for Synaptics LuxPad window appears.
4 In the left side of the window, select Ta ppi ng . 5 Select Dual Mode.
67
6 Select Switch to Button Mode by tapping in the upper-
right corner.
To force the Dual Mode Pad to use Button Mode only whenever an external pointing device such as a mouse is plugged in, select Always in Button Mode when an external device is plugged in.
Configuring virtual buttons
The virtual buttons at the top of the Dual Mode Pad are preconfigured for the Email, ConfigFree, and Print functions. You can assign different functions to these buttons if you wish.
The virtual buttons on the bottom of the Dual Mode Pad (buttons 4, 5, and 6 in the Properties for Synaptics LuxPad window) are unassigned by default. In order to use one of these buttons, you must first configure that button so that it is associated with a function.
Getting Started
68

Using external display devices

To configure a virtual button:
1 Perform steps 1-5 in “Enabling Dual Mode” on page 67. 2 Select the virtual button you wish to configure.
3 Select the desired options, then click OK. 4 Click OK. 5 Click OK to close the Mouse Properties window.
Using external display devices
Your computer comes with a built-in LCD display, but you can also connect the following types of external display devices to the video ports described below:
A plasma television or VCR/DVD player via the HDMI
Out port
A standard television, projector, or VCR/DVD player via
the S-video Out port
An external monitor or projector via the RGB (monitor)
Out port
Before connecting a television, video projector, monitor or other external display device, configure your computer for the type of device you are connecting. To do this, refer to the documentation for your operating system and the device.
Coaxial Antenna In port
(Sample Illustration) Back of system
You cannot connect both the S-video Out port and the HDMI Out port to the same device at the same time.
The system display default is set at the factory to S-video Out.
RGB (Monitor) Out port
HDMI Out port
S-video Out port
Using external display devices
NOTE

Connecting the display device

If you are connecting a television or other video display device to the computer’s HDMI Out port, first refer to
“Selecting video cables” on page 69 for guidelines on
choosing a video cable, then refer to “Connecting a plasma
television or VCR/DVD player” on page 70.
If you are connecting a standard television or other video display device to the computer’s S-Video Out port, first refer to “Selecting video cables” on page 69 for guidelines on choosing a video cable, then refer to “Connecting a standard
television, projector, or VCR/DVD player” on page 71.
If you are connecting an SVGA monitor, first refer to
“Selecting video cables” on page 69, then skip to “Connecting an external monitor or projector” on page 73.
Selecting video cables
To connect a device to the S-video port, you must purchase an S-video cable. To connect a device to the HDMI Out port, you must purchase an HDMI cable.
Getting Started
69
S-video cables and HDMI cables are not included with your computer.
For the best video quality, always use a properly shielded cable.
HINT: Toshiba recommends using a cable no longer than 20 feet (approximately 6 meters).
Using a poor-quality cable may result in a dull or fuzzy picture, poor color, ghosting, video noise, or loss of video.
70
Getting Started
Using external display devices
Connecting a plasma television or VCR/DVD player
To connect a plasma television or VCR/DVD player to the computer:
1 Connect one end of an HDMI cable (not included with
your computer) to the HDMI Out port on the back of your computer, and then connect the other end of the cable to your television. Refer to the manual that came with the television for more information.
2 Turn on your computer. 3 While holding down
between each press, until you get the desired setting. For more information, see “Directing the display output when
you turn on the computer” on page 73.
Fn, press F5 repeatedly, pausing
Connecting the sound to a TV or stereo system
At times you may prefer to use external audio instead of the computer’s built-in speakers. For example, when you use a TV or other external display device you can use that device’s speakers, or when you use the computer’s built-in display you can connect to external speakers or a stereo sound system for higher quality sound.
You can connect the sound to external audio devices in two ways:
Using the headphone jack on the left side of the
computer—This lets you connect directly to headphones, powered speakers, or a stereo system that supports input from a headphone output. You need a cable (not shipped with your computer) with a 1/8" (3.5mm) stereo plug on one end and a plug compatible with your sound system on the other end (typically an RCA type connector).
Using the S/PDIF jack on the left side of the computer—
This lets you connect to a sound system that can accept the digital optical signal from your computer. You need an S/PDIF cable (not shipped with your computer) with a
Getting Started
NOTE
Using external display devices
Toslink 1/8" (3.5mm) mini plug on one end and a plug compatible with your sound system on the other end.
71
Connecting a standard television, projector, or VCR/ DVD player
To connect a standard television, projector, or VCR/DVD player:
1 Connect one end of an S-video cable (not included with
your computer) to the external video device. Refer to the documentation provided with the device for
the location of its Video In port.
2 Connect the other end of the video cable to the S-video
Out port on the back of the computer.
3 Turn on the external video device. Make sure the input to
the device is correctly set for the S-video port. (See the device’s documentation for more information.)
4 On your computer, press the TV Out button, or toggle
the display using the TV Out button is located above the keyboard.)
If you do not see the image transfer from your computer screen to the external video device, modify the Display Properties as described in “Adjusting the Display Properties” on page 72.
Fn + F5 hot key combination. (The
72
Getting Started
Using external display devices
Adjusting the Display Properties
When using the S-video display port, the desktop shown on your TV may be larger than the screen can show. As a result, you may have to adjust the Display Properties to show the entire desktop on the TV without having to pan the display.
To adjust the display properties
1 Right-click on the Windows Desktop and click
Properties. The Display Properties dialog box appears.
2 In the Display Properties dialog box, click the Settings
tab.
(Sample Image) Settings Tab
3 On the Settings tab, click and drag the Screen resolution
slider to the left to select a lower screen resolution.
TECHNICAL NOTE: Most televisions use or support an 800 x 600 standard resolution.
4 Click Apply, then click OK to close the Display
Properties window. The screen is now displayed correctly on your TV. For more information, see “Directing the display output when
you turn on the computer” on page 73.
Getting Started
Using external display devices
73
Connecting an external monitor or projector
You can easily attach an external monitor or projector to your computer if you need a larger screen or to display anything on your computer screen. To do this:
1 Connect the monitor’s video cable to the RGB (monitor)
port on the back of the computer.
2 Connect the device’s power cable to a live electrical
outlet.
3 Turn on the external device. 4 Turn on or restart the computer. 5 While holding down
between each press, until you get the desired setting. For more information, see “Directing the display output
when you turn on the computer” on page 73.
Fn, press F5 repeatedly, pausing

Directing the display output when you turn on the computer

Once you connect an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. The quickest way to change the display output settings is to use the display hot key (
1 While holding down
between each press, until the setting you want takes effect.
This hot key cycles through the settings in the following order:
Built-in display only Built-in display and external monitor simultaneously External monitor only Built-in display and TV (or other external video
device) simultaneously
Fn, press F5 repeatedly, pausing
Fn + F5):
74
NOTE
NOTE
Getting Started
Using external display devices
TV (or other external video device) only
Built-in display and external monitor (extended
desktop)
Built-in display and TV (extended desktop)
(Sample Image) Display options window
The dual display modes (internal display and external device) cannot be used while you are watching an HD DVD.
The right-most icon in the above illustration is for the Swap Image Display mode. This mode is available only if the current setting is an extended desktop mode (Built-in Display and External Monitor, or Built-in Display and TV). In extended desktop mode, the image is split into two sides, one side per display device. To swap sides, select Swap Image Display.
2 Release the
TECHNICAL NOTE: You can also change these settings using the Display Properties Box.
Set the option for the video controller by clicking Start, then Control Panel, and Display. Choose the Settings tab, click the Advanced button, select Display Device, select the applicable Monitor type, and click Apply or OK.
Fn key.
Getting Started

Connecting External AV Input Devices

Adjusting the quality of the external display

To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings. See the video device documentation for additional configuration steps.
TECHNICAL NOTE: To use one of the simultaneous modes, you must set the resolution of the internal display panel to match the resolution of the external display device. The external display device must support a resolution of 800 X 600 or higher.
Connecting External AV Input Devices
Your computer provides ports for connecting the following AV input devices:
A Set-top box or standard television antenna via the
coaxial Antenna In port
75
VCR/DVD player and game console devices via the S-
video In port or the Composite In port
Connecting a Set-top box or standard TV antenna
You can watch standard television by connecting a Set-top box or antenna to the Antenna In port on your computer. To do this:
1 Connect the television Set-top box or antenna to the
coaxial adapter cable.
2 Connect the coaxial adapter cable to the coaxial Antenna
In port on the back of your computer.
3 Turn on your computer. 4 If the computer is on, launch Media Center (refer to
“Starting the Media Center” on page 173), or if the
76
NOTE
Getting Started
Connecting External AV Input Devices
computer is off, launch QosmioPlayer (refer to“Using
QosmioPlayer” on page 156).
Connecting to the S-video In port
You can connect an external input device such as a VCR/ DVD player or game console to the S-video In port on the right side of your computer.
S-video cables are not included with your computer. To connect a device to the S-video In port, you will need to purchase an S-video cable.
To connect the device:
1 Connect one end of the video cable to the external video
device.
Refer to the documentation provided with the device for
the location of its Video Out port.
2 Connect the other end of the video cable to the S-video In
port on the right side of the computer.
3 Turn on the external video device.
Connecting to the Composite In port
The Composite In port provides another way to connect a VCR/DVD player or game console to your computer. To do this:
1 If the computer is on, turn it off (see “Turning off the
computer” on page 81). If the external device is on, turn
it off.
2 Connect the external device’s video and audio cables to
the Composite video/audio adapter cable.
3 Connect the Composite adapter cable to the Composite In
port on the right side of the computer.
Getting Started
Connecting External AV Input Devices
4 Connect the device’s power cable to a live electrical
outlet.
5 Turn on your computer. 6 Turn on the external device. 7 Press the TV button above the keyboard.
The QosmioPlayer TV application starts.
77
8 If necessary, change the input source by pressing the
repeatedly until Composite In is selected. The supported sources are:
Coaxial cable/Antenna In S-Video Composite In
The system will remember the selected input source after the computer is turned off. If you want a different setting to be in effect the next time you turn on the computer, change the input source before turning off the computer. The default setting for the input source is Antenna In.
For more information refer to “Watching television” on
page 160.
When you are finished, press the power button to shut down QosmioPlayer.
i key
Getting Started
NOTE
NOTE
78

Using an external keyboard

Using an external keyboard
If you prefer to use a full-size keyboard, you can attach one to your computer. The computer’s USB ports support any USB­compatible keyboard.

Using a mouse

You may want to use a mouse instead of the computer’s built­in Dual Mode Pad. You can use a USB-compatible mouse.
After logging on to your system, the mouse cursor may move to the upper-right side of the screen. If this occurs, press the
Esc or Windows key to return it to its original position.

Connecting a printer

Your printer documentation may require you to install the printer software before physically connecting the printer to your computer. If you do not install the software as instructed by the printer manufacturer, the printer may not function correctly.
Read the documentation that came with your printer. Follow the manufacturer’s instructions when connecting a printer.
You can connect a USB-compatible printer to your computer through the USB ports. To determine if the printer is USB­compatible, check its documentation.
To make the connection, you need a suitable USB cable which may come with your printer. If a USB cable was not included with your printer, you can purchase one from a computer or electronics store.
If your printer supports Plug and Play, your computer will
NOTE
automatically recognize the printer; the printer is then ready for use. Refer to your printer documentation for further instructions.
TECHNICAL NOTE: To determine if your printer supports Plug and Play, check its documentation.
If your printer does not support Plug and Play, you can set up the printer as described in “Setting up a printer” on page 79.
To connect a printer to your computer:
1 Connect the printer cable to the printer and then connect
the other end to one of the computer’s USB ports.
2 Plug the printer’s power cable into a live AC outlet.

Setting up a printer

Getting Started
Connecting a printer
79
Some printers require a specific installation process. Refer to your printer installation guide for instructions before completing the following procedure.
If your printer does not support Plug and Play, follow these steps to set it up for the first time. You only need to set up the printer once.
1 Click Start, and then Printers and Faxes.
The Printers and Faxes window appears.
Getting Started
80

Connecting an optional external diskette drive

2 Click Add a printer.
The Add Printer Wizard appears.
(Sample Image) Add Printer Wizard
3 Follow the on-screen instructions to set up your printer.
Connecting an optional external diskette drive
Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5­inch diskettes.
(Sample Illustration) Optional external USB diskette drive
To connect an optional external USB diskette drive, connect the cable to one of the computer’s USB ports.
(Sample Illustration) Connecting an optional external USB diskette drive

Turning off the computer

Getting Started
Turning off the computer
81
Pressing the power button before shutting down the Windows work. Make sure the system indicator panel’s disk light and the drive-in-use light are off. If you turn off the power while a disk/ disc is being accessed, you may lose data or damage the disk/ disc and/or drive.
It is a good idea to turn off your computer when you are not using it for a while.
If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is off) to fully charge the main battery.
®
operating system could cause you to lose your

Options for turning off the computer

Depending on the operating system installed, you have more than one option available for turning off the computer: Turn Off or Shut Down, Hibernate, and Standby. Each option has its advantages.
82
Getting Started
Turning off the computer
Turn Off or Shut Down
Factors to consider when choosing either Turn Off or Shut Down:
Use the Turn Off command if you are using Windows
XP Home, or either Windows
Windows
®
XP Media Center Edition (MCE) and are not
connected to a domain server.
Use the Shut Down command if you are using Windows
XP Professional and are connected to a domain server.
®
XP Professional or
®
®
If you have work in progress and are not connected to a
network, use the Windows
®
Standby or Hibernate commands to save your system settings so that, when you turn on the computer again, you will automatically return to where you left off.
TECHNICAL NOTE: Before using any of these options to shut down or turn off your computer, save your files and make sure all disk/disc activity lights are off.
If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again.
Hibernation mode
Hibernation mode shuts the computer down completely, but it first saves the current state of the computer to the hard disk. Since Hibernation mode does not require power to maintain the saved information, system settings are retained indefinitely.
Factors to consider when choosing Hibernation:
While in Hibernation mode, the computer uses no main
battery power.
Because the state of the system is stored on the hard disk,
no data is lost if the main battery discharges.
Getting Started
Turning off the computer
Restarting from Hibernation takes less time and
consumes less main battery power than restarting from turning off the computer.
Since information is being retrieved from the hard disk
rather than from memory, restarting from Hibernation takes a little more time and consumes more main battery power to start up than when restarting from Standby.
When starting up again, the computer returns to the state
in which you left it, including all open programs and files you were using.
For information on how to use and configure Hibernation mode see “Using and configuring Hibernation mode” on
page 87.
83
Standby mode
The Standby command places the computer into a power­saving mode. Standby holds the current state of the computer in system memory (RAM) so that, when you restart the computer, you can continue working from where you left off.
Factors to consider when choosing Standby:
While in Standby mode, the computer uses some main
battery power.
The Standby command does not store unsaved
information on your hard disk. You should save your work before putting your computer on Standby.
Restarting from Standby takes less time and consumes
less main battery power than restarting from turning off the computer or using Hibernation mode.
Getting Started
84
Turning off the computer
When starting up again, the computer returns to the mode
in which you left it, including all open programs and files you were using.
If you power down using the Standby command and the main battery discharges fully, your unsaved information will be lost. Be sure to save your work first.
For information on using Standby, see “Using and
configuring Standby mode” on page 89.

Using the Turn Off Computer or Shut Down commands

Depending on the operating system installed, use the following steps to turn off your computer.
Turn Off
For Windows Professional or Windows domain server, follow these steps to turn off the computer:
®
XP Home, or either Windows
®
XP MCE when not connected to a
®
XP
1 Click Start, and then Turn off computer.
The Turn off computer dialog box appears.
(Sample Image) Turn off computer Windows
2 Click Turn Off.
The computer shuts down completely.
®
dialog box
Getting Started
Turning off the computer
85
Shut Down
For Windows server, follow these steps to turn off the computer:
1 Click Start, and then Shut down.
The Shut Down Windows
2 Select Shut down from the drop-down list. 3 Click OK.
The computer shuts down completely.
®
XP Professional when connected to a domain
®
dialog box appears.
Turning off the computer more quickly
You can also turn off the computer by pressing the power button.
To use this method, you first need to activate it using Toshiba’s Power Saver utility.
1 Click Start, Control Panel, and then Performance and
Maintenance.
2 Click the Toshiba Power Saver icon. 3 Click on the Setup Action tab.
(Sample Image) Setup action settings screen
86
NOTE
Getting Started
Turning off the computer
4 Select the options you want from the drop-down lists.
When I press the power button
Set this option to Shut down if you want the computer to shut down when you press the power button.
When I close the lid
Set this option to Shut down if you want the computer to shut down when you close the display panel.
5 Click Apply. 6 Click OK.
For more information about the Power Saver utility, see
“TOSHIBA Power Saver” on page 270.
Once the computer is configured, you can turn it off by either pressing the power button or closing the display panel, depending on the options set.
Restarting your computer
To start the computer up again, press the power button until the on/off light glows blue.
If you turn off the computer by closing the display panel, you can start it again by opening the display panel.
Getting Started
Turning off the computer

Using and configuring Hibernation mode

To turn off the computer using the Hibernation command, click Start, Turn off computer, and then select Hibernate.
(Sample Image) Turn off computer Windows® dialog box
The computer saves the state of all open programs and files, turns off the display, and then turns off.
Configuring Hibernation mode options
You can place the computer into Hibernation mode by either pressing the power button or closing the display panel. You can also specify an amount of time after which the computer automatically goes into Hibernation mode.
87
To use any of these methods, you first need to enable them in Toshiba’s Power Saver utility.
1 Click Start, Control Panel, and then Performance and
Maintenance.
2 Click the Toshiba Power Saver icon. 3 Click the Setup Action tab.
88
NOTE
Getting Started
Turning off the computer
4 Select Hibernation for the options you want.
When I press the power button
Set this option to Hibernate if you want the computer to go into Hibernation mode when you press the power button.
When I close the lid
Set this option to Hibernate if you want the computer to go into Hibernation mode when you close the display panel.
5 Click Apply. 6 Click OK.
For more information about the Power Saver utility, see
“TOSHIBA Power Saver” on page 270.
Once the computer is configured, you can place it into Hibernation mode by either pressing the power button or closing the display panel, depending on the Hibernation options set.
Starting again from Hibernation mode
To start up the computer from Hibernation mode, press the power button until the on/off light glows blue. The computer returns to the screen(s) you were using.
If you put the computer in Hibernation mode by closing the display panel, you can start it again by opening the display panel.
Turning off the computer

Using and configuring Standby mode

To turn off the computer using the Standby command, click Start, Turn off computer, and then select Stand By.
(Sample Image) Turn off computer Windows® dialog box
The computer saves the status of all open programs and files, turns off the display, and enters into a low-power mode. The on/off light blinks amber indicating the computer is in Standby mode.
Configuring Standby mode options
Getting Started
89
You can place the computer into Standby mode by either pressing the power button or closing the display panel. You can also specify an amount of time after which the computer automatically goes into Standby mode.
To use any of these methods, you first need to enable them in Toshiba’s Power Saver utility.
1 Click Start, Control Panel, and then Performance and
Maintenance.
2 Click the Toshiba Power Saver icon. 3 Click the Setup Action tab.
90
NOTE
Getting Started
Turning off the computer
4 Select Standby for the options you want.
When I press the power button
Set this option to Standby if you want the computer to go into Standby mode when you press the power button.
When I close the lid
Set this option to Standby if you want the computer to go into Standby mode when you close the display panel.
5 Click Apply. 6 Click OK.
For more information about the Power Saver utility, see
“TOSHIBA Power Saver” on page 270.
Once the computer is configured, you can place it into Standby mode by either pressing the power button or closing the display panel, depending on the Standby options set.
Starting again from Standby mode
To start up the computer from Standby mode, press the power button until the on/off light glows blue. The computer returns to the screen(s) you were using.
If you place the computer in Standby mode by closing the display panel, you can start it again by opening the display panel.

Closing the display panel

After you have turned off the computer, close the display panel to keep dust and dirt out of the computer.

Caring for your computer

Caring for your computer
This section gives tips on cleaning and moving your computer. For information about taking care of your computer’s battery, see “Taking care of your battery” on
page 130.

Cleaning the computer

Keep liquids, including cleaning fluid, out of the computer’s keyboard, speaker, and other openings. Never spray cleaner directly onto the computer. Never use harsh or caustic chemical products to clean the computer.
To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth.

Moving the computer

Getting Started
91
Before moving your computer, even across the room, make sure all disk activity has ended (the drive indicator light stops glowing) and all external peripheral cables are disconnected.
Do not pick up the computer by its display panel or by the back (where the ports are located). Doing so could damage the system.
Getting Started
92
Caring for your computer

Using a computer lock

You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com.
(Sample Illustration) Computer lock cable
To secure the computer:
1 Wrap the cable through or around some part of a heavy
object. Make sure there is no way for a potential thief to slip the
cable off the object.
2 Pass the locking end through the loop. 3 Insert the cable’s locking end into the security lock slot
on your computer, then engage the locking device. The computer is now securely locked.
(Sample Illustration) Attaching security lock cable
Chapter 2
Learning the Basics
This chapter gives some computing tips and provides important information about basic features.

Computing tips

Save your work frequently.
Your work stays in the computer’s temporary memory until you save it to the disk. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved.
See “Saving your work” on page 101 for further information.
HINT: Some programs have an automatic save feature that can be activated. This feature saves your file to the hard disk at preset intervals. See your software documentation for details.
93
94
NOTE
Learning the Basics
Computing tips
Back up your files to disks (or other removable media) on
a regular basis. Label the backup copies clearly and store them in a safe place.
It is easy to put off backing up because it takes time. However, if your hard disk suddenly fails, you will lose all the data on it unless you have a separate backup copy.
Use Error-checking and Disk Defragmenter regularly to
conserve disk space and improve performance.
Scan all new files for viruses.
This precaution is especially important for files you receive via diskette, email, or download from the Internet.
Take frequent breaks to avoid repetitive-motion injuries
and eyestrain.
Do not turn off the computer if a drive indicator light
indicates a drive is active. Turning off the computer while it is reading from or
writing to a disk may damage the disk, the drive, or both.
Before turning off the computer, use the Turn off
computer command or Standby command. See “Using
and configuring Standby mode” on page 89 to learn more
about Standby.
The Windows® operating system records information, such as your desktop setup, during its shutdown procedure. If you do not let the Windows details such as new icon positions may be lost.
®
operating system shut down normally,

Using the keyboard

Learning the Basics
Using the keyboard
95
Your computer’s keyboard contains character keys, control keys, function keys, and special Windows the functionality of a full-size keyboard.
(Sample Illustration) Keyboard

Character keys

Typing with the character keys is very much like typing on a typewriter, except that:
The space bar creates a space character instead of just
passing over an area of the page.
The lowercase letter l (el) and the number 1 are not
interchangeable.
®
keys, providing all
The uppercase letter O and the number 0 are not
interchangeable.

Making your keyboard emulate a full-size keyboard

Although your computer’s keyboard layout is compatible with a standard full-size keyboard, it has fewer keys.
A standard full-size keyboard has two editing keys; cursor positioning keys; and a numeric keypad. Pressing the of the specially marked keys allows you to emulate a full-size keyboard.
Fn key simultaneously in combination with one
Enter, Ctrl, and Alt keys;
Learning the Basics
96
Using the keyboard
Your computer’s keyboard has only one Enter and one Ctrl key. Most of the time, this does not matter. However, some programs assign separate functions to the right and left
Alt keys, or to the regular and numeric pad Enter keys on
and the full-sized keyboard. Using the these separate keys, as follows:
Press Fn and Ctrl simultaneously to simulate the Ctrl key on
the right side of the enhanced keyboard.
Press Fn and Enter simultaneously to simulate the Enter key
on the numeric pad of the enhanced keyboard.

Ctrl, Fn, and Alt keys

FN
CTRL
(Sample Illustration) Ctrl, Fn, and Alt keys
Ctrl, Fn, and Alt keys do different things depending on the
The program you are using. For more information, see your program documentation.
Ctrl
Fn key, you can simulate
ALT

Function keys

The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard.
(Sample Illustration) Function keys
F1 through F12 are called function keys because they execute
programmed functions when pressed. Used in combination with the specific functions on the computer. For example, off the Dual Mode Pad. For more information, see
“Fn-esse®” on page 263, or “Hot Keys” on page 338.
Fn key, function keys marked with icons execute
Fn+F9 turns

Windows special keys

(Sample Illustration) Windows special keys
Your computer’s keyboard has two keys that have special functions in Windows:
Windows key—Opens the Start menu Application key—Has a similar function as the
secondary mouse button

Overlay keys

The keys with gray numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the 10-key keypad on a desktop computer’s keyboard.
Windows key
Application key
Learning the Basics
Using the keyboard
97
(Sample Illustration) Numeric and cursor control overlay
Learning the Basics
98

Starting a program

Using the overlay to type numeric data

The keys with the numbers on their right front are the numeric overlay keys.
To turn the numeric overlay on, press simultaneously. The numeric mode light on the keyboard indicator panel glows when the numeric overlay is on.
To disable the numeric overlay, hold down the
F11 again. The numeric mode light on the keyboard
press indicator panel goes out.
Using the overlay for cursor control
The keys with the gray arrows and symbols on their left front are the cursor control overlay keys.
To turn the cursor control overlay on, press simultaneously. The cursor control mode light on the keyboard indicator panel glows when the cursor control overlay is on.
To disable the cursor control overlay, hold down the and press keyboard indicator panel goes out.
F10 again. The cursor control mode light on the
Starting a program
The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows
Fn and F11
Fn and F10
Fn key and
Fn key
®
Explorer.
If you prefer to open the program first, you have four options. You can:
Double-click the icon for the program on your desktop Use the Start menu Use Windows
program file
Use the Run dialog box
®
Explorer or My Computer to locate the
Learning the Basics
Starting a program
The next three sections explain how to start a program from the Start menu, Explorer and the Run dialog box.

Starting a program from the Start menu

When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that has an icon in the All Programs menu, follow these steps, which use the Windows
1 Click Start, and then All Programs.
The Windows Programs menu, which lists programs and program groups. If your program is listed, go to step 3, otherwise, continue with step 2.
2 Click the program group, in this example, Accessories.
The Accessories menu is displayed.
3 Click the program, in this example, Wor dPad.
®
WordPad program as an example:
®
operating system displays the All
99
WordPad opens. To close the program, click the Close button in the upper-
right corner of the program’s window.

Starting a program from Windows® Explorer

If a program is not listed in the All Programs menu, you can start it from Windows you a view of your computer’s contents as a hierarchy or “tree.” You can easily see the contents of each drive and folder on your computer. To use this method, you should know the file name and location of the program’s executable file (this file ends with .exe).
This example opens WordPad using Windows Explorer.
1 Click Start, and then All Programs. 2 Click Accessories.
®
Explorer. Windows® Explorer gives
100
Learning the Basics
Starting a program
3 Click Windows Explorer. 4 Click My Computer to expand the window. 5 In the left part of the window, click the line that ends in
“(C:).”
6 In the left part of the window, under the C: icon, double-
click the folder containing the program, in this case Program Files.
Windows Files folder on the right side of the window. The left side of the window shows all the folders contained within the Program Files folder.
7 In the left part of the window, click Windows NT. 8 In the left part of the window, click Accessories.
Windows
Accessories folder on the right side of the window.
9 In the right part of the window, double-click wordpad.
®
Explorer shows the contents of the Program
®
Explorer shows the contents of the
The operating system opens WordPad. To close the program, click the Close button in the upper-
right corner of the program’s window.

Starting a program from the Run dialog box

This example uses the Run command to start WordPad:
1 Click Start, and then Run.
The Run dialog box appears.
(Sample Image) Run dialog box
Loading...