Page 1
BSINo. G00J129 Page 1
n
BSI No.: G00J129
Publish
2000/11/06
Date:
Subject: ROM Improvement (300M: 09->10, 302M: 03->04, 304M: 01->02)
Model: DP4580, DP5570, DP6570, DP8070
Category Field Application UNIT
Addition of the Function, To
improve the reliability
FactoryApplication: From Oct. at the factory
Others Software
CONTENT
The ROM has been changed as follows.
[Changed/Added Part No.]
MODEL P-I Before Change After Change Note P I R
PM-551
PM-651
DP5570
DP6570
DP4580 62-33 4407893050
PM-801
DP8070
P-I: Page-Item P: Contents of Change I: Interchangeability R: Reasons for Change
[Changed Contents]
z
62-33 4406383180
PRA-300M-09
PRA-302M-03
62-33 4408856080
PRA-304M-01
Countermeasure to soiling of back of the copy (TABS indication)
When toner is forcibly added mode during printing, the rotation of the fuser unit has been
changed to stop or become low.
(Reason for change)
Especially in copiers which make a lot of duplex copies or prints (70% or greater), the cleaning
roller ( P .32-I.37 4409893740 B-8070L ) becomes more soiled than usual. So, after to
been added, soiling at the back of the copy occurs very rare.
Abnormal heating of the cleaning roller (P.32-I.37 4409893740 B-8070L) causes the fuser to
run idly at the time of toner supply. A control to prevent such idling has been added.
4406383270
PRA-300M-10
4406383290
PRA-302M-04
4406383280
PRA-304M-02
C B D -
C B D -
C B D -
FAA
8-figure counter (TEG request)
z
Each of the following counters have been changed from 6 figures to 8 figures.
Code
251 PM counter, setting value
252 PM counter, current value
351 Electronic counter
Setting Item
Page 2
BSINo. G00J129 Page 2
*353 Short size counter
*354 Long size counter
358 Manual bypass feed counter
359 LCF counter
360 Upper cassette counter
370 Middle cassette counter
371 Lower cassette counter
372 ADU counter
374 DF counter
375 Copy job counter
376 Print job counter
401 Drum counter
404 Developer counter
PS)
The codes "353" and "354" were not included in the Service Handbook; their details are given in
this BSI.
Setting Mode (08)
Code
Setting Item Mode Image
mode
Default Allowable Remarks Operation
procedure
group
353 Short size counter ALL 0 0 ~
99999999
354 Long size counter ALL 0 0 ~
99999999
1
1
Countermeasure to toner scattering
z
As a [Countermeasure when Toner Scattering occurs in the Market (Temporary Measure) ] ,
an ATS control (single item) (lowered by 10 bits) has been inserted in the ROM. For the
cause and complete countermeasure, see
BSI #.G00I099
.
Together with this change, the control for the "developer material life control switching
(08-414)" is added.
0 --- ATS control is listed in
BSI #.G00I099
.
(The ROM has a supplementary value 10 bits lower than before the change.)
1~3 --- See below
4 --- Correction control of ROM before change
Current ROM PRA-300M-09
PRA-302M-03
PRA-304M-01
PS)
z
Usually select "0".
Even if "0" is selected, it can be found that toner scattering does not stop in special cases
such as repeat printing of small quantities.
In this instance, select 1, 2, 3 in steps.
Select "2" in the following case. When "0" is selected and toner scattering soils the image
z
after 200,000 to 300,000 copies. "1" is an intermediate stage between "0" and "2",
whereas "3" is above this.
However in low humidity conditions, "2" and "3" can reduce the image density.
When the new ROM is applied; If toner scattering occurs on the market, as a
z
countermeasure manually return the machines which have had 10 bits reduced to their
previous status by the following method.
(Adjustment Method)
Write the value of 08/404.1.
With the UP key in 05/200, raise the current control bit value by 10 bits.2.
Page 3
BSINo. G00J129 Page 3
Press the setting key.3.
In 04/404 once again, input the written value (1) using the digital keys.4.
Setting Node (08)
Code
414 Developer powder life
[ Combinations of ROM Versions ]
They should never be operated except in the following combinations.
As only the following combinations can have their operation checked, errors could well
occur with other combinations.
Setting Item Mode Image
mode
ALL 0 0~4
control switching
versions
Default Allowable Remarks Operation
0:X-10bit
1:
-14bit
X
2:
-20bit
X
3:
-30bit
X
4:
X
: Correction control value before the following
X
PRA-300M-09
PRA-302M-03
PRA-304M-01
procedure
group
1
System ROM
Printer ROM
PMA-T300S*zzzz
PRA-300M-zz
PRA-302M-zz
PRA-304M-zz
Laser ROM
Scanner ROM
PFC
Finisher ROM
PRA-300L-zz
PRA-300S-zz
PRA-300F-zz
PRA-502FIN-zz
(saddle)
Finisher ROM
PRA-793FIN-zz
(stacker)
RADF ROM
Table of History of ROM Version Combination
Time of Application
PRA-794DF-zz
System
ROM
Printer
ROM
Laser
ROM
0207
10
04
02
11
07
07
05
06
04
Scan
ner
ROM
PFC
BSI No
Time of
Application
1st lot 0075 05 06 06 05 -
1999/5 0086 06 07 06 06 F99E643
F99E644
1999/6 (0097)
0108
System
ROM
Printer ROM Laser
07 08 06 06 F99F680
F99F684
ROM
Scanner
ROM
PFC Finisher ROM RADF
BSI No
ROM
Page 4
BSINo. G00J129 Page 4
PRA
- 304M
PRA
- 302M
PRA
- 300M
Saddle Stacker
1999/7 0129 -- -- 07 08 06 06 04 05 03 F99G727
1999/9 0130 -- 02 08 08 07 06 04 05 03,04 F99H748
F99J825
1999/10 0141 -- 02 08 08 07 06 04 05 04 F99J795
1999/11 0152 -- 02 08 08 07 06 04 05 04 F99K838
2000/1 0163 -- 02 08 08 07 06 05 06 04 F99K845
F99K846
F99K863
F99K864
F99L866
2000/2 0173 -- 02 08 08 07 06 05 06 04 G00B932
2000/4 0185 -- 03 09 09 07 06,07 05 06 04 G00D005
2000/4 0185 01 -- -- 09 07 07 05 06 04
2000/5 0185 -- 03 09 10 07 06,07 05 06 04 G00E033
0185 01 -- -- 10 07 07 05 06 04
2000/6 0196 01 03 09 10 07 07 05 06 04 G00F056
2000/8 0207 01 03 09 10 07 07 05 06 04 GOOH088
2000/10 0207
02 04 10
11 07 07 05 06 04 G00J128
GOOJ129
Attached File
Related Documents:
LinkTo: Link From:
Loading...